Search Documents

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By José Cuadros

"El presente trabajo señala el proceso de evolución del método de minado en la mina Chupa, perteneciente a la unidad minera de Iscaycruz. La evolución del método de minado se determinó por la búsqueda de mejores condiciones de seguridad y eficiencia en la operación. En ese sentido, los resultados logrados con cada una de las alternativas de minado por subniveles, indica que se ha logrado optimizar las diferentes variables mineras y cumplir con el plan estratégico de Empresa Minera Iscaycruz S.A. (EMISA). Para cumplir con el citado plan estratégico, se debe optimizar el método de minado de Chupa, a través de una mayor producción a un menor costo,así como del aprovecho de las labores de desarrollo y preparación ejecutadas según el planeamiento inicial del minado. Por ello, la secuencia del avance del minado y la reestructuración del sistema de relleno de la mina son los aspectos importantes para lograr este objetivo. "

Jul 31, 2003

As it is my opinion that deep alluvial mining in Victoria and in the Murray Flats in New South Wales is practically in its infancy, and considering that we, the old school of alluvial miners, who have thirty or forty years' experience to guide us, must in the natural order of things hand over the management of our mine, to the younger and less experienced' generation of miners, I thought that as our Association has been formed for the purpose of disseminating information and the exchange of ideas, a few notes on the practical working of alluvial mines might be of some service to aspirants for the position of mining manager.The greatest difficulty the alluvial miner has to contend against is the immense quantity of water contained in the drifts overlying the wash in the gutters or ancient river beds, and to cope with this water successfully and economically is the point to be aimed at by our mining managers; and if they thoroughly understand this part of their business in all its details, they will not only win kudos for themselves, but will be the means of saving large sums of money to the companies they represent, and, in many instances, will make a success of a venture which otherwise might be stopped for want of funds before it is properly proved. At the present time, although we have had over forty years' experience indraining the deep leads of the colony, I regret to say that a large amount of ignorance still prevails amongst both directors and managers.

Jan 1, 1901

By Daniel H. McClain

A unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT)Center resulted in a video CD-ROM training program for new miners entering the aggregate industry. Cooperation from everyone involved, including the U.S. Mine Safety and Health Administration (MSHA),made this the product against which other training materials in the mining industry will be measured in the 21stcentury. This product’s versatility and wide application make it a tool that is as critical to a mine’s success as any earthmoving machine. The state and federal grant money involved allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2003

By Green P. F

Apatite Fission Track Analysis (AFTA) is a thermal history reconstruction tool that enables determination of magnitude and timing of maximum paleotemperature and paleo-geothermal gradient at the time of maximum paleotemperatures. From this information, the amount of section missing at major unconfornities can be estimated and incorporated into basin models. The Gippsland Basin has a number of distinct problems that can be tackled using AFTA. 1. The nature of the regional break between the Late Cretaceous-Tertiary Latrobe Group and the underlying Early Cretaceous Strzelecki Group. 2. The tectonic history of the basement flanking the basin and its effect on sediment composition. 3. The age of igneous activity in the basin, as typified by the widespread basaltic plugs and dykes intruding the outcropping Strzelecki Group. Major uplift and erosion within, and adjacent to, the early Cretaceous rift basin in the Mid-Cretaceous, at -95 to 100 Ma, initially constrained the Latrobe Group depositional area to the central deep of the Gippsland Basin and provided an elevated source of quartz-rich detritus for the Latrobe Group reservoirs. This is in marked contrast to the preceding period in the early Cretaceous when contemporaneous volcanism dominated as a source of detritus, producing quartz-poor lithic sandstones, in which a host of attendant diagenetic reactions destroyed their reservoir potential. Initial uplift and erosion of the volcanogenic Strzelecki Group also occurred in the mid-Cretaceous as revealed by a number of distinct inversion structures, and erosion of this material will have locally provided very poor quality sand to the basal Latrobe Group.

Jan 1, 1992

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By Brent C. Jellicoe, Phil Robertshaw, J. Murphy, Peter Williamson

Kimberlites and associated diamonds have been the focus of extensive exploration in central Saskatchewan since 1988. During 1989, Uranerz Exploration and Mining Limited identified 71 shallow magnetic anomalies in the Fort a la Corne area from detailed aeromagnetic surveys. By the end of 1991, 18 of these targets had been proven, by drilling, to be kimberlite bodies encased within Cretaceous sedimentary strata. From 1991 to 1997, the number of drill-confirmed kimberlite bodies increased to 69. Our current view, drawing on an integration of geophysical and geological information, is that the kimberlites are composed of individual bodies and multi-vent clusters of coalesced bodies, all apparently constructed of stacked, temporally distinct layers of pyroclastic crater-facies kimberlite. Diamond recoveries and geochemical results from associated heavy minerals at Fort a la Corne remain highly variable, although continued minibulk sampling is expected to improve the estimation of diamond grades for the most prospective bodies.

Jan 1, 2001

By Alex Del Castillo

The mineral processing industry has followed the development of database control systems, and various systems have been installed in existing and new plants. The goal is to improve product quality, raise productivity and lower production costs. Improvements in different units for mineral .processing .have been applied. This has led to increasing information for the operators. To support the operators and for an easy overview of the process, a complete concept for an integrated process-control system is required. This paper describes the plant-wide [process control system for the Collahuasi copper project located in northern Chile. The total investment for the project was $1,700,000,000 and included a port area and two copper processing plants, an oxide plant with a cathode production of 50 tons per year and a sulfide plant with a concentrate production of 330 kilotons per year. The main characteristics of the plant-wide process control system include a 200- kilometer long redundant control network and a 24-kilometer long redundant serial network providing coverage for the entire plant. The plants are located around 4,700 meters above sea level, serial communication lids allow the integration of over 2,700 SCADA data units, and the system handles over 7,500 physical signals plus the SCADA data integration. The main equipment consists of 39 different sized controllers, 16 operator stations, 5 engineering stations, 2 information management systems and 4 X- terminals. The project management, control configuration, factory acceptance test, system integration test, training, commissioning and start-up were carried out in close cooperation with the customer. The result was completely satisfactory for the customer.

Jan 1, 1999

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By Kanau JL, Kilgour I

This paper describes the metallurgical processes at the 80 000tpd Ok Tedi Mining Limited concentrator, which treats copper- gold ore by single-stage crushing, SAG and ball milling and flotation to produce over 500 000tpa of concentrate. Plant and process developments, including installation of column cells, reduction of fluorine in concentrate, use of sulphidisation and process control improve- ments are also discussed.

Jan 1, 1991

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interiors This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941.£1 No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed

Jan 1, 1949

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

By B. H. Moore

The opportunity to evaluate the pile design procedures used on a major project is an infrequent occurrence. It is even more infrequent that the project involves piles with significant tension and horizontal capacities. This report synopsizes over twenty years of design and construction experience on just such a major pile founded structure. The philosophy governing foundation design procedures is described and discussed. The order and extent of full scale pile testing are evaluated. Principal points in the specifications are established and their effect on construction progress and claims are noted. The report concludes with recommendations for future projects.

Jan 1, 2010

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By R. F. Shurtz

The problem of estimating the precision of systematic samples from a mineral deposit is attacked by interpolating the quality, or other attribute measured, by using Fourier approximation. Such approximation using trigonometric functions yields a particularly simple expression for the variance of the mean value of the attribute sampled. The increasing volume of publication in which the science of statistics has been applied to the problem of predicting the quality of an ore deposit from sets of samples taken from it might lead one to believe that engineering judgment can be replaced by statistics. There is, in fact, an implicit application of the principle of indifference or of "no advance knowledge" which has been discredited in modern statistical theory and practice. These pages will show that it is not always advantageous, efficient, or safe to apply this principle. This problem will be dealt with by using series of orthonormal functions to describe the distribution of the quality of ore in space as contrasted with the more commonly used distribution of quality as a frequency function. Mining engineers are rarely well acquainted with the use of such series or of the functions comprising them. These uses are commonplace in the fields of communication and information theory and it is not surprising that applications taken from these fields should be found appropriate for the analysis of the information contained in a set of samples from an ore deposit. It is hoped that presentation of the following basic, but incomplete, results will generate wider interest in this method and a fuller development of it as well as of the necessary computational techniques. FUNDAMENTAL PREMISES Random variables in the strictest sense are not very common in mine sampling. The sets of samples are almost always taken systematically and are, hence, not subject to all the laws governing random events. Therefore, unless there is indeed random experimental error in the determinations of quality, the treatment of systematic samples of n members as though they were random samples of n members often leads to calculation of confidence limits for the mean quality which are larger than they should be with the result that unnecessary additional sampling is done. The reason for this will emerge in the following discussion leading to Eq. 24 and its generalization. In order to inquire into such questions on a rigorous basis and at the same time avoid arithmetic complications that would obscure the concepts involved, a one dimensional distribution of quality will be assumed. The quality, Q, in suitable units is expressed as a function of the distance, x, along some straight traverse of the deposit. Such a function

Jan 1, 1967

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991