Search Documents

By Louis J. Mittoni

"It is well known that gas injection systems can exhibit a wide range of dynamical behaviours, ranging from linear periodic bubbling through to highly complex turbulent jetting. Recently, it has been observed that an important intermediate regime exists under certain system conditions, where the dynamics are complex in nature yet predictable for short time periods. This paper reviews the evidence to support the above hypothesis, and discusses the invariant quantitative measures such as density, return maps, Lyapunov exponent and dimension which may be used as pattern recognition features in a mOnitoring and control strategy.INTRODUCTIONThere has been a great deal of research on the submerged injection of gases into liquids. This interest is primarily due to the large number of applications in the pyrometallurgical and chemical engineering industries. Gases are typically injected into liquids to achieve goals such as heat and mass transfer, or physical mixing and agitation. Only recently though has the possibility of using the evolution of the gas dynamics as a probe to internal system conditions been raised [1, 2].At very low gas injection rates and small upstream chamber volumes, gas normally disperses in the form of stable bubbles of constant volume [3]. With increases in gas flow rate, the dynamics become more complex, bifurcating into double bubbling, multiple bubbling and complex coalescence behaviour. Irregularities measured in pressuretime series acquired upstream of the injection port under these complex conditions have usually been treated as bothersome noise or contamination to be filtered from the signal and ignored in the analysis. These irregularities, however, may contain physically interesting and useful information on the system from which they were produced if the system may be classified as deterministically chaotic [4]."

Jan 1, 1996

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By G. Nazari

ERAMET, through its subsidiary COMILOG, have rights to a rich niobium and rare earth deposit inGabon. The Mabounié deposit, is located 50 kmfromthe town of Lambaréné, in a fairly remote location. ERAMET has been developing a process to recover value metals for several years, and approached Hatch Ltd. to design a sizeable Demonstration Plant to help them further optimize the process, and prove the flowsheet is technically viable. The process employs concentration techniques to recover an upgraded Nb/REE feed material for processing in the subsequent leach step. Rare earths and niobium are selectively leached, and subsequently precipitated. Following precipitation, rare earths undergo bulk separation and are purified to produce LRE and mixed MRE/HRE products, which will be further processed by Third Parties. This paper provides a high-level overview of the process, summarizes the motivation for a Demonstration Plant in the vicinity of the deposit, and discusses technical challenges faced during the flowsheet definition and design phase. Key challenges are focused on and summaries of the methodologies used to address each challenge, as well as the solutions to overcome the challenges, are discussed. The paper provides motivation for further process simplification and concludes with a project update.

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By J. K. Brimacombe

Plant trials have been conducted at the Tacoma Smelter of ASARCO to assess the effect on tuyere blockage and refractory erosion at the tuyere line, of increasing the injection pressure of air into a Peirce-Smith con¬verter. Four tuyeres each having an ID of 19.1 mm (3/4 in) were installed toward one end of the tuyere line of the No. 4 Converter. Air and oxygen-enriched air were injected at 414 kPag (60 psig) through these tuyeres and at the usual 83 kPag (12 psig) through the remainder of the tuyeres in an otherwise normal converter campaign. The test campaign consisted of 88 charges and lasted for 89 days. During this period, punching of the high-pressure tuyeres was found to-be unnecessary; and when, as a precaution, the tuyeres were cleaned by hand at the end of a charge, they were always open. Also it was observed that the flow of high-pressure air remained constant. Accretion formation around the tip of the high-pressure tuyeres varied from charge to charge and was influenced by the matte grade and the level of oxygen enrichment.

Jan 1, 1983

By A. Treverrow, G. A. Brooks, H. K. Worner

"The work by H.K Worner and co-workers at CRA in the 1960s, and early 1970s, established that molten metals could be refined continuously utilising counter current flow of metal and slag. Womer also demonstrated that counter current refining could produce highly refined metal products. These developments coincided with the advent of high intensity metallurgical reactors in both the ferrous and non-ferrous industries (e.g. BOS, Q-BOP and later Sirosmelt) that utilised high levels of gas injection to produce rapid stirring and very fast reaction. These new generation of high intensity metallurgical reactors allowed high tonnage rates through relatively small volume vessels.Whilst, it is well known that the counter current flow of reacting phases offers the potential of efficient mass transfer and high purity products, the application of counter current reactors to molten metal/slag systems has been criticized on the basis that they suffer from either low intensity or, alternately, from poor refining due to excessive dispersion. These criticisms relate to the balance between intensity and the refining capacity of a reactor. That is, whilst high levels of mixing transversely to the direction of flow promotes high mass transfer, longitudinal mixing (dispersion) is detrimental to refining. Of course, mixing in one direction invariably leads to mixing in other directions, thus creating a playoff between high mass transfer and excessive dispersion.This balance between intensity and refining has been the subject of recent studies overseas, and at"" the University of Wollongong, using cold modelling techniques to evaluate the effect of mixing on dispersion in a counter current refining launder. These studies have shown that for a given geometry and mixing regime, dispersion decreases with increasing flow of liquid phases. This means that whilst high mass transfer cannot be achieved in a refining launder without sacrificing the degree of refinement, there is no impediment to achieving high productivity through such a system, in fact, high through puts may favour good refining. Thus, it may be possible to match a high productivity smelting operation with a equally productive counter current refining stage."

Jan 1, 1996

By V. M. Paretsky

Oxygen-flame converting of a solid ground matte containing heavy non-ferrous metals in a wide range of concentrations is one of the perspective trends meeting the demands of modern non-ferrous metallurgy. As. a result, of semicommercial tests on oxygen-flame smelting of nickel matte containing 13,5-17,5% Ni; 0,45-0,65% Co under continuous autogenous conditions a converter matte containing 68 8-75,0% Ni and 0,48-1-,0% Co and ferrite -calcium slag containing 1,4-8,4 Ni and 0,16-0,56 Co were pro¬duced. Nickel recovery in a converter-matte was 76,2%, copper - 58,'2% and cobalt recovery in. a slag was 90%. Slag cleaning in an electric furnace allowed to after-recover nickel and cobalt in an alloy to produce a dumpy slag containing 0,03% Ni and 0,02% Co. The development of modern' ecologically pure energy-saving autogenous technologies of the treatment of sulphide raw materials containing heavy non-ferrous metals makes certain demands of the perfection of a process of converting rich sulphide-metallic intermediate products obtained at autogenous smelting. These-demands were connected first of all with the fact that converting process stages because of process periodicity are more unfavourable from the point of ecology, power intensity and unit stability. Besides, during rich matte treatment the problems connected with heat shortage when using air blast and heat excess-when using top oxygen blast to treat luquid matte a-rise and when enriching air blast by oxygen up to 26% fast erosion of the brickwork of a tuyere zone takes place. The technology of Outokumpu and Kennecott companies-on solid- copper matte converting in a flash smelting furnace using air blast is not universal as its possibilities are limited by certain composition of mattes. Besides, flash smelting to produce highly basic or combined slags requires larger enrichment-of blast by oxygen or extra fuel feed. Naturally a flowsheet with continuous converting of matte of various composition up to white matte production is simple,

Jan 1, 1993

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450°C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By Nathan A. Tiner

Sulfuric acid anodizing process is extensively used in many industrial and consumer products to provide corrosion resistance to aluminum alloys. The anodic coatings produced consist of amorphous alhnum oxide with a pornus structure which is easily sealed and colored with dyes. The coatings may contain defects due to surface flaws, canposition and microstructure of the aluminum alloy, and/or due to the anodizing process conditions. This paper will describe the techniques used in anodizing process, various defects which may be produced in anodic coatings and the methods to control them.

Jan 1, 1992

By John A. Herbst

Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen and the coordination of all unit operations in pursuit of the highest performance level. However several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of Unit operations to account for critical interactions within and 'between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that 'knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significantly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated With the models and can be effectively optimized. Financial goals seems to be the objectives of choice. This paper discusses recent progress In overcoming the challenges and illustrates a promising approach which is being pursued at :Mexicana de Cobre's 'La Caridad copper ore concentrator. At M de C, advanced ,control strategies have been 'installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, 'increased from 76;000 tpd to 90,000 tpd. Plantwide integration is expected' to gain an additional 3% improvement in profitability.

Jan 1, 1996

By William Petruk

"Heap leaching is a developing technology for recovering native gold and electrum from low grade deposits and from tailings. Recovery depends on permeability of the rock and ore minerals, size of particles in the heap, and ore textures that influence exposure of gold grains to cyanide solutions. These ore textures include gold-bearing veinlets and microveinlets along fractures and microfractures, gold grains in porous minerals and rocks, and gold graim. occurring along grain boundaries of other minerals. On the other hand, small encapsulated gold grains arc not likely tote exposed even with fine grinding. Most gold grains that occtir along grain boundaries of other minerals can be exposed with a moderate to fine grind, but the. resulting material will be too fine-grained to be permeable in a heap. Such finely ground ore, as well as tailings from flotation operations, can however be prepared for heap leaching by agglomerating the material into porous briquettes. Oxidized and weathered zones above. orebodies are frequently amenable to heap leaching because the gold-bearing pyrite and arsenopyrite have become permeable by conversion to porous iron oxides and ferric oxyhydroxides. A review of ore textures in several types of gold deposits suggests that:(1) the gold in vein deposits would gtmerally be amenable to heap leaching of both oxidized ores and fresh non-refractory ores,(2) the gold in Carlin-type deposits and in volcanogenic massive sulfide deposits is not likely to be amenable to heap leaching fresh ore, but oxidized zones above the orebodies are generally amenable to cyanidation, and(3) the gold in porphyry copper-gold deposits and in Witwatersrand-type deposits would likely be amenable to heap leaching of both fresh and oxidized ores but with high cyanide consumption."

Jan 1, 1997

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The disposal of wastes is a serious environmental problem, since available landfill space is dwindling. Their treatment by pyrolysis or combustion has merit, and the corresponding fuel or power production is of technological interest. However, such processes need a rigid control of emissions. This work addresses the gaseous light hydrocarbons (LHCs) generated during sequential pyrolysis and partial oxidation of unserviceable tires, PET bottles, com wastes (DDGS) and sugarcane bagasse in a two-stage laminar-flow horizontal furnace, kept at 1000 °C. Gas chromatography was used to identify and quantify the components of the emitted gaseous light hydrocarbons. The results showed that the biomass residues generated the highest emissions of aliphatic hydrocarbons, whereas PET generated the most aromatic hydrocarbons. When stainless steel meshes were inserted in the exhaust flow, it was found that hydrocarbon emissions were curtailed; as such meshes catalyzed partial conversion of these carbon-bearing gases to carbonaceous nanomaterials.IntroductionLight hydrocarbons (LHCs) are volatile organic compounds, consisting of hydrogen and carbon with low molecular weight; the most common species are methane, ethane, propane, butane, etc. LHCs are valuable since they are a very important energy resource. However, uncontrolled release of light hydrocarbon gases to the atmosphere should be avoided [l, 2]. In this work, a development is presented for the evaluation of LHCs generated during the controlled pyrolysis/combustion of several wastes in a two-stage laminar-flow horizontal furnace. Samples of unserviceable tires, post-consumer PET bottles and waste residues from the bioethanol industry (DDGS and sugarcane bagasse) were burned. A catalyst system, consisting of stainless steel screens, was tested for its effects on the gaseous emissions."

Jan 1, 2011

By M. Nilmani, H. Pham

"A mathematical model was developed for the dissolution of particles in gas-stirred liquid baths, linking the hydrodynamic flow field of the bath, the average particle trajectory and liquid-side mass transfer controlled dissolution kinetics. The model was validated by comparison with experimental data for the dissolution rates of urea particles in gas-stirred aqueous CaCl2 solutions measured during this study. The dissolution rates of urea. particles were measured using an image analysis system.The effects of operating conditions on the dissolution rates of urea particles were investigated. It was found that the key operating parameters influencing the utilisation efficiency of particles were the gas flowrate, particle diameter and lance submergence. An optimisation of the operating conditions for the model urea-aqueous CaCl2 system indicated that the utilisation efficiency increased with decreasing gas flowrate and decreasing particle size for a given lance submergence.IntroductionThe utilisation solid reagents in molten baths varies from one process to another, depending upon the rates and mechanisms of the reactions between the particles and melts, as well as the trajectory and residence time of the particles in the melts. Previous studies have not attempted to predict the utilisation efficiency of injected solids by coupling the motion of the particle with its dissolution rate. Instead, the particles have usually been assumed to remain suspended in the bath until completely dissolved, and the mass transfer coefficients were based on the average specific mechanical energy dissipation rates in the bath. Investigations of this nature relevant to the present study have been undertaken by Apelian et al. [1], Brucato et al. [2] and Langberg and Nilmani[3]. The objective of the present study was to develop a mathematical model, incorporating both the reaction kinetics between the particles and liquid and the particle motion simultaneously, to predict the dissolution rates and times of the particles. The mathematical model was validated by comparison with experimental dissolution rates of a cold model analogue system measured using an image analysis technique, and then applied to optimise the operating conditions in the model system."

Jan 1, 1996

By M. Hashimoto

The equilibrium distribution ratios of sulfur between molten copper and CaO-fluxes containing caF2 and caC12 were determined in the range of 1300° to 1400° C under carbon monoxide. The rate of approach to equilibrium is rapid and increases with increasing CaCll concentration. In CaO-CaFl-CaCl2 fluxes, the distribution ratio varies in a complex way with temperature and CaFl concentration. The results are compared with those obtained with the binary fluxes of CaO with BaFZ and MgFl ?

Jan 1, 1983

By William Petruk

Mineralogical and image analysis studies have been performed on four volcanogenic base metal ores that contain 0.01 to 4.5 wt% Pb to determine the behaviour of galena during mineral processing. The galena in these ores is fine grained and is poorly liberated in both the primacy and regrind mill discharges. Consequently, low grade Pb concentrates are produced to obtain relatively high Pb recoveries. The Pb concentrates contain many impurities including high amounts of pyrite and sphalerite, and small amount of CU-, As-, Ag-, Bi-, and Se-sulfides. These impurities need to be rejected from the Pb bullion during smelting. The galena commonly contains up to 1 wt% Ag in solid solution with an average of 600 to 1460 ppu for the deposits studied to date. The Ag in galena accounts for up to 65% of the Ag in some ores.

Jan 1, 1990

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By William Petrul

Image analysis studies were performed on mill products from laboratory flotation tests of the Zn-Pb ore from the Faro deposit in Yukon, Canada, to determine mineral liberations at specific grinds and to predict recoveries at optimum flotation conditions. The minimum and optimum grinds for liberating sphalerite and galena were predicted from size analysis data for the minerals in large ore pieces, and determined by image analysis studies of the mill products. The determined optimum grinds are about 2 Tyler mesh sizes larger than predicted because sane of the fine grained sphalerite and galena occurs in interstices between coarser grained pyrite and is liberated when the pyrite grains are broken apart. Materials balance calculations were performed on the analyzed values for the liberated and unliberated sphalerite and galenaa to determine their distributions in the mill products. The laboratory flotation tests recovered 74% of the sphalerite and 83% of the galena in Zn and Pb concentrates respectively. The mineral evaluation study indicates that the optimum recovery for sphalerite and galena are 85 and 83% respectively. The company is currently recovering 80% 'of the sphalerite and 82% of the galena.

Jan 1, 1989