Search Documents

By Hong Ouyang

A unified computational model has been developed for the Bridgman growth processes of B-NiAI and CdTe crystals. To handle the geometrical and physical complexities, a two-level approach has been developed. At the gtobatlevel, conjugate heat transfer, phase change dynamics, and variable material properties along with the realistic geometries and thermal boundary conditions are accounted for inside the entire crystal growth system. Refined calculations are then made within the ampoule, with the boundary conditions supplied by the global simulations. This model can optimize the use of computational source, help understand solidification behaviors, and improve designs of crystal growth system.

Jan 1, 1996

By M. Oliazadeh

Spodumene [LiAl(Si2O6)] is the most common and desirable economic lithium-bearing mineral due to its high lithium content. In Canada, there are several spodumene deposits at the development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and increasing use of electric vehicles. Spodumene processing can be conducted using Dense Media Separation (DMS), flotation or combination of both. If spodumene liberation is sufficient at coarse particle sizes, DMS can be used for primary lithium concentrate production and silicate gangue minerals rejection. If liberation is not sufficient, flotation is then the main processing route for spodumene concentration. Even in cases where DMS is a viable beneficiation option, flotation may still be required to process the DMS middlings and/or the undersize fraction which is outside the particle size range for DMS. Considering flotation as a technique for spodumene beneficiation, there are several alternatives including the use of mechanical flotation cells, column flotation cells, coarse particle flotation cells, and/or Staged Flotation Reactors (SFR), either alone or in combination. Ore sorting can be incorporated at the start of the spodumene flowsheet to remove gangue minerals, particularly amphibole and pyroxene in the early stages. The main objective of flowsheet development for hard rock lithium deposits is to evaluate the ability of these options to produce a spodumene concentrate with a concentrate grade above 6% Li2O, lithium recovery of above 80%, and with the minimum operating and capital cost. This paper aims to describe the various processing options available for the beneficiation of spodumene from hard rock deposits and compare the associated operating and capital costs for each.

By Teuku A. R. Putra, Patrick R. Taylor

Various pyrometallurgical methods for treating copper concentrates that contain appreciable arsenic are reviewed. Various aspects of the engineering of these treatment methods are discussed. The methods discussed include: complete oxidation with arsenic fixation; selective volatilization of arsenic; acid baking, soda ash roasting, and others methods. Methods for the ultimate disposal, or marketing, of the arsenic are discussed.

Jan 1, 2014

By Wei Luo, Yuanbo Zhang, Zhixiong You, Zijian Su, Guanghui Li, Tao Jiang

"In this study, the appropriate sintering process parameters for low-grade ferromanganese ores were investigated. The results showed that, under the condition of natural basicity (R=0.03), the optimal parameters were obtained as follows: moisture of mixture 9 .1 %, coke powder 9 .9% and sintering negative pressure 7 KPa. And the corresponding yield, ISO tumbling index and utilization coefficient reached at 80.18%, 61.27% and 1.515t·m-2·h-1, respectively. Under the optimal parameters, the emission of harmful gases, such as S02 and NOx, were reduced evidently with 30% of coke powder replaced by biomass charcoal. Moreover, it was found that the basicity had obvious effects on the quality of the sinters when it changed between 0.03 and 2.4. The ISO tumbling index gradually decreased from 61.27% to 55.47% with the basicity increasing from 0.03 to 1.2, then, it began to increase after the basicity further increased to 2.4.IntroductionManganese is mainly consumed by steel and battery industries, particularly in the steel plants and ferroalloy units. The consumption of metal manganese in the ferroalloy industry accounts for 85%-90% of the total Mn [1-2]. Therefore, ensuring sufficient manganese alloys is essential to meet the rapid development of steel industry. Recently, rich-manganese slag containing high grade Mn (>40%), low Fe (1%) and P (<0.03%) is considered as superior raw materials for manganese alloys. While the sinters made from manganese ores are major raw materials for producing rich-manganese slag with the increasing exhaustion of natural rich manganese lump ores [3-5]."

Jan 1, 2013

By Liming Wang

One of the steps in the extractive metallurgy of lead is a refining process called drossing. Hot dross is mixture of impurity compounds that form on the surface during the cooling of lead blast furnace bullion, and in Missouri, the main impurities are copper and sulfur. The slow cooling of bullion throws out of solution all other minor impurity elements (or their compounds) which are much less soluble at lower temperatures (mainly nickel, arsenic, iron, and zinc). The transfer of bullion from the blast furnace to the refinery and the subsequent hot drossing step cause fugitive emission of lead-containing fume and dust, which creates a plant hygiene problem. One cause of the emissions is the high vapor pressure of lead and its compounds during transmission of = 1000 °C bullion to the drossing kettle. Another cause is the lifting of dross dust during manual skimming of dross. The environmental problems associated with the traditional hot drossing process provided an incentive to investigate a new drossing process that avoids contact between plant air and hot bullion or dross. A key aspect of the process development was a detailed mineralogical examination of dross from two different bullions. The bullion samples were cooled at different rates, and the dross filtered out and examined. The morphology, phase identification, and composition of the dross was examined by optical and SEM microscopy. The principal dross phases were copper and cuprous sulfide, galena, a complex sulfide containing copper, nickel and lead, and speiss (containing nickel, cobalt, iron, copper, lead, and arsenic compounds). The copper was acicular, with nickel and arsenic in solid solution. The cuprous sulfide was largely digenite in a granular or dendritic form. A substantial part of the dross was solidified matte with a eutectic microstructure, consisting mainly of CU2S and PbS. Small particles (some of which had a eutectic microstructure) never floated to the surface of the lead during the slowest cooling rate, thus indicating that flotation of tiny matte droplets and dross crystals is exceedingly slow. The success in separating dross and lead by centrifugal filtration suggests its application in industry as a replacement for traditional hot drossing.

Jan 1, 1995

By Ram V. Ramachandran

As an industry with major potential impacts (both good and bad) on water resources and due to the rising costs of process water, the mining and metallurgical processing industry has a key responsibility to contribute to the overall goal of preserving both the quantity and quality of water available within the watersheds they operate in. As we plan for new and existing mining and metallurgical projects, we need to consider a hierarchy of options to minimize our impact within the watersheds we operate; keeping clean water clean by diverting around our operations; reduction in the amount of water we use; reuse of water wherever possible, and improvements to water quality for recycling and/or release to environment. Technology is needed to treat water to improve its quality for reuse or release to the original watershed. While lime precipitation followed by sulfide polishing is effective for removal of most of the metals, it does little or nothing to remove ammonium ions and anions such as chloride, nitrate, molybdate, arsenate and selenite/selenite. Regulations on sulfate limits in treated discharge water has drawn close attention to the treatment of acid mine drainage (AMD). Management of brine and salt disposal is also posing a problem due to strict regulations and cost of disposal. This paper will: (a) address issues associated with managing water with the objective of maintaining water sheds—status quo-during and after operation (b) discuss potential technologies for advanced water treatment plants.

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be &apos;increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FexAs2O2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS203 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By L. A. Neumeier

The Bureau of Mines, U.S. Department of the Interior, is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide .phases by sulfldation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes initial research involving sulfidation partitioning of chalcopyrite concentrates. Small chalcopyrite samples were sulfidized with elemental sulfur in glass capsules sealed after evacuating and backfilling with helium, by heating for 1 to 24 h at specific temperatures in the range of 250° to 500° C. which extends from below to above the boiling point of sulfur (-445° C). Above the boiling point of sulfur, the overall reaction with adequate sulfur (13.9 wt pct of CuFeS2) is 5CuFeS2 + 4S g ? Cu5FeS6 + 4FeS2.

Jan 1, 1989

By Liu Chunpeng

Under an inert atmosphere, the temperature enhancement of nickel bearing pyrrhotite irradiated by microwave was measured with a special metal-sheathed thermocouple and the non-isothermal rate equations were obtained. Under the controlled oxygen potential of the reacting gas in the microwave field, over 90% sulfur contained in the pyrrhotite is converted into elemental sulfur directly, the iron and the nickel are transformed into FeO,, NiO, NiFe,O, and FeSiO,. According to the experimental data the rate of the elemental sulfur produced is in diffusional control and the non-isothermal equation derived is

Jan 1, 1993

By Hebi Yin

A coupled cellular automaton (CA) - finite element (FE) model was developed to calculate the growth of dendrites during the solidification of cubic and hexagonal metals. The model solves the conservation equations of mass, energy and solutes in order to calculate the temperature field, solute concentration and the growth morphology of dendrites, including the grain structure and the dendritic microstructure. Validation of the model was performed by comparing the simulation results with calculation results from previously published works, showing qualitatively good agreement in the dendritic morphology. Application to magnesium alloy AZ91 illustrates the difficulty of modeling dendrite growth in hexagonal systems, observed as deviations in growth direction caused by mesh-induced anisotropy. The model was applied to the simulation of small specimens with single- and multiple- equiaxed grain growths and columnar grain growth in directional solidification. The influence of cooling rate and some kinetics parameters on the grain morphology are also discussed.

Jan 1, 2009

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don&apos;t allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir&apos;s law is discussed for different operating conditions.

Jan 1, 1996

By W. W. Albrecht

I. Introduction Refractory metals like tungsten, molybdenum, rhenium, tantalum and niobium and their compounds are essential ingredients of our modern technology. Especially in purified form, they are used in special alloys, electronics, optics and ceramics. The processing route from raw material to high purity refractory metals and their compounds includes, as a prime option, the following steps: - dissolution of raw materials. - liquid liquid extraction. - precipitation of high purity intermediate compounds. - calcination/reduction to high purity oxides/metals. Especially in the first three steps, major amounts of chemicals like acids or sodium hydroxide are used and, as by-products, substantial quantities of residues and effluents are generated. The impact of environmental regulations on these by-products and the attempt to reduce or minimize the amount of residues and effluents produced will be discussed in this presentation using Ta/Nb chemistry as the example. The basis of our considerations will be the way these by-products are handled at HCST, a major, and in some cases, the biggest producer of refractory metals (tungsten, molybdenum, rhenium, tantalum, and niobium).

Jan 1, 1992

By R. A. Spitz, R. Leiby, M. Bricker

Electrochemistry plays a significant role in minimizing wastes at East Penn's secondary lead smelter. East Penn has been recovering spent battery acid for reuse in new batteries since 1992. East Penn also produces a fertilizer feedstock from sulfur dioxide in the smelter stack gases. The success of these processes is, in large part, due to the installation of electrochemical cells. The cells in the acid recovery plant allow the waste from this process to be concentrated into less that 10% of the original spent acid. The cells in the fertilizer plant treat the solution to remove dissolved metals prior to sale to fertilizer manufacturers.

Jan 1, 2000

By Zhao Hengxian

We studied the phase diagram of Na3AlFe-ZrO system, reduction of ZrO2 by aluminium and electrochemical behaviours of ZrO2 in the system. The results show that Na3ALF6-ZrO2 system is a simle eutectic one, that the velocity of reduction of ZrO2 in the system is rapid al 960&apos;C and that the Zr content in the alloy abtained can reach as high as 2.5wt%. Potential scanning shows that there exist new current peaks on the potential scanning plats except for the cuurent peaks corresponding to the oxidation of aluminium. The method of making Al-Zr alloy in our paper has advantages over the traditional method of mixing metals.

Jan 1, 1992

By C. M. Diaz

The chemistry of the main unit processes in nickel extractive pyrometallurgy is reviewed. Key re1a ions between smelter feed composition and process selection are discussed, with particular reference to operating conditions, energy requirements and products. The paper a1 so includes a brief discussion of current nickel smelters, based on the results of a recent survey carried out by TMS.

Jan 1, 1988

By T. T. Chen

Hydrometallurgical products are difficult to characterize because of their fine grain sizes, heterogeneity, often amorphous structures and water soluble or hydrated constituents. Such products are advantageously studied using complementary mineralogical techniques including >50, ore microscopy, SEM-EDX, electron microprobe analysis, selective leaching and wet chemical analysis to determine the phases and their morphologies, to identify specific element carriers, and to elucidate the chemical reactions occurring during the metallurgical process. Sample preparation is an important consideration for these materials. For extremely fine-grained particles, or soft and brittle products such as elemental sulphur, the study of loose powder mounts provides information not available from the examination of polished sections. To demonstrate the application of the various mineralogical techniques, commercial zinc roaster calcines and leach residues, copper refinery anodes and anode slimes, and laboratory bornite leach residues were examined in detail. The various sample preparation and mineralogical methods are presented, and the use of these complementary and practical mineralogical techniques to improve the understanding of a particular hydrometallurgical system is discussed.

Jan 1, 1989

By Chris Twigge-Molecey

As emission constraints for metallurgical plants become more difficult to meet; control of major, multi-vessel, flue systems become more critical. Control instabilities can result in significant loss of system capacity or emissions to the environment. This paper will discuss the use of dynamic simulation techniques to optimize both the design and control strategies for these systems. A significant ,safety hazard is associated with pressure excursions from process upsets or equipment failures. Pressure rise rates of up to 10 kPajsec can occur. These cannot-be followed by conventional controls. Fail-safe high speed venting is required to protect both the furnaces and operating personnel&apos;. Design options, sizing techniques and practical problems are discussed.

Jan 1, 1992

By Thierry De Nys

A direct leaching process of sulphidic zinc-based concentrates in aqueous sulphuric acid solutions has been developed by the V.M. R & D Department. By a very accurate control of the oxidation potential of the leach solution, this process enables a separate recovery of the zinc, copper, silver, lead and sulphur of the concentrate and makes it extremely attractive for treating more complex ores. The iron, solubilized during leaching, is eliminated out of the zinc solution by means of the V.M. goethite process. Alternative flow sheets for a conventional zinc electrolysis plant are presented.

Jan 1, 1990

By J. A. Holmes

Due to varying and complex mineralogy, the flotation tailings from the Chingola Concentrator have, for some years, contained upwards of 0.4% acid soluble copper. In 1968, an investigation was initiated, to determine a method for recovering this acid soluble copper. This initial investigation concluded with a recommendation to install a leach-solvent extraction-electrowinning plant at Chingola, to treat up to 900 000 tonnes of material per month, for an additional copper production of some 4 500 tonnes per month. The process consists basically of six stages :- Materials reclamation handling and preparation, acid leaching in air agitated pachucas, solid-liquid separation by countercurrent washing in thickeners, solution concentration and purification by solvent extraction, copper recovery by electrowinning, and residue neutralisation and disposal. This paper describes the development of the main parameters for design of each of the six sections, and gives details of the final plant design. Problems encountered in commissioning and initial operations are commented on, particularly insofar as they indicated any errors or misjudgements in the design. The choice of materials of construction is commented on in some detail.

Jan 1, 1976