Search Documents

By P. Louis

Although cobalt is known and used for its hardness and wear resistance, ductile cobalt can be obtained by electrolysis in chloride solutions, under the following conditions : pH : 1.5 - 2, Co++ : 30 - 60 g/l, current density : 100 - 500 A/m2, temperature 40 - 70°C. No explanation was found for the ductility of the deposit under these conditions. Indeed the ductile P (FCC) cobalt and the hydrogen contents in the cobalt deposits are nearly the same as those obtained in a sulfate media, which gives brittle depo¬sits under equivalent electrolysis conditions. Malleable cobalt sheets can be easily obtained under the proposed conditions which could lead to new applications for cobalt.

Jan 1, 1988

By M. Okido, R. Ichino, K. Kuroda

"Compound semiconductor, ZnTe, was electrodeposited in an acidic solution with K2TeO3, ZnSO4 and Na2SO4 solution. Since the reduction potential Te(IV)/Te(O) is remarkably noble from the solution comparing to Zn(II)/Zn(O), code position of Te and Zn was thought to be difficult from this solution. Resulting from EQCM analysis, furthermore, Te(IV) reduced to Te(O) and Te(-II) in this order so that Te catholically dissolved from the electrode surface at more negative potential. But ZnTe alloy were formed by the UPD of Zn at -0.7V at 298K on Te surface in lmM K2TeO3, 100mM ZnSO4 and 100mM Na2SO4 solution adjusted at pH 4. Content of Te in the deposits is, however, more than 80%.Electrolytic temperature is well known to affect on the deposits characteristics. The higher bath temperature was, the better ZnTe crystal was detected in this study. Thermal electrode method is a. process of heating only substrate by flowing ac current in substrate. This process makes the surface temperature of substrate higher than boiling point of the solution, 373K. From EDX analysis, deposits without thermal current were Te-rich, Te content in the deposits with thermal current decreased with increasing of thermal current. Te content was 62% for 5A ac current, 51 % for I OA and 45% for 20A, respectively. The deposits that produced with ac current of IOA were closed to the stoichiometric ratio, i.e. ZnTe.Consequently, thermal electrode method is more effective to obtain a good crystallized ZnTe without heat treatment after deposition.IntroductionThe current subject of solar cell materials is silicon. Compound semiconductors including GaAs and II-VI group are generally used in the developing field of digital information such as the rapid cellular phone and car telephone. Compound semiconductors consist of more than 2 kinds of element. There are many materials for these compound semiconductors such a SiC, InSb, CdS for binary system and CuinSe2 for ternary system. It becomes generally difficult, to produce high quality crystal with increasing of kinds of element due to a complicated structure and a compound ratio of element. Semiconductor materials as a device are usually simple binary compounds and/or these mixed crystals. Properties of compound semiconductors have variety of the forbidden band and lattice constant and that can be change easily by addition of another element for the usage of the solar cell. Since most compound semiconductors are direct interband transition type, which has steep optics absorption edge and large light absorption coefficient."

Jan 1, 2000

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"In this study we attempted to model a response surface for the apparent dry density of ternary blends of calcitic marble particles. The crushed marble was divided into three granulometric ranges. Simplex network methodology was used to determine the mathematical relation between granulometric ranges and apparent dry density (ADD) of particle mixtures. A highly significant regression was obtained and the simplex network methodology proved to be able to predict high packing particle compositions.IntroductionProblems with packing and expected porosity of particles are common and widely recognized to be important in terms of both fundamental physics and engineering applications. For example, densification of a powder mass is important in the shaping of solids in ceramics, powder metallurgy or composite synthesis; chemical processes such as solid-liquid separation (sedimentation, thickening and filtration), raw material handling (stockpiling, blending, drying, storage and transportation) and pyrometallurgical processes (agglomeration, coke making, ore sintering, blast furnace iron making and new iron making processes) [1,2].Many factors can affect particle packing, but in practice, there are three main factors: (dimensionless) particle size distribution, particle shape and absolute particle size [2].Geometrical and practical methods were developed to predict properties in mixtures. Zou, Gan and Yu [2] present a paper treating a prediction of the porosity of multi-component mixtures of cohesive (fine) and non-cohesive (coarse) particles. Bahiense et al. [3,4] used a simplex network to determine a mathematical model for obtain the optimal compositions between aggregates to a greater packing of a ternary particles mixture. Despite these techniques for predicting particle packing, some studies in particulate composites production don't present clear criteria for choice of particle distribution [5,6]. As the best particle packaging depends on the size, distribution and shape of these particles, individual models can be constructed for specific combinations of these factors."

Jan 1, 2014

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By Jerome P. Downey

Technologies developed within the field of extractive metallurgy to recover, concentrate, and purify metals and industrial minerals from ores, have served as the foundation for all of the subsequent environmental remediation, materials recycling, and waste management technologies. This paper discusses the application of classical extractive engineering principles to the development of a thermal process for the recovery of mercury from solid wastes. Process development is presented as a series of logical stages, which begin with a thorough characterization of the site-specific waste, move on to bench and pilot scale testing of the process options, and end with a functional process flowsheet. This paper also presents thermodynamic data on many mercury species of interest to the minerals, power, and chemical industries. These data can be used to model the speciation and recovery of the mercury as a function of various process parameters.

Jan 1, 2003

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By Jefferson Caponero

The tire is an expressive component of Municipal Solid Waste, manly when its occupied volume is considered. Its treatment by pyrolysis stands for a list of advantages, such as: landfill releasing and a production of a high quality fuel. The exploitation of new natural resources is becoming more difficult each day, basically due to the environmental damages caused by this type of activity. This work presents a study on the thermal behaviour of Brazilian tires using thermogravimetric analysis and differential thermal analysis, in order to optimise the pyrolysis process of tires. Samples of I to 2 mm were investigated at atmospheres of nitrogen, argon, oxygen and mixtures of these gases at temperatures up to 1273K, under heating rates between 1 to 50 Klmin . The results showed that the behaviour of each sample is related to both the atmosphere composition and the heating rate.

Jan 1, 2001

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderurgica Belgo Mineira, Joao Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By A. Haxhiaj, Mitovica, E. Haxhiaj

"The paper discusses problems encountered during the release and possibility of using the thermal gas quantity Mathematical models are used to calculate the positive thermal effects of the gases and losses of thermal quantity with gases in the melting process of electric furnaces. The paper discusses in details the percentages of CO, CO2, H2S, O2 and the humidity in gases and their impact on the technological process in electrical furnaces in Drenas. The paper also confers the quantity and temperature of gases, the transfer of thermal quantity and dust with gases in the environment. The paper presents the percentage of humidity in the load which is added in electric furnace for melting and its impact on thermal and environmental balance in the technological process of melting in electric furnaces. Key words: Furnace, load, temperature, humidity, gases.IntroductionNickel easily reacts with gases in the atmosphere of the furnace in which the nickel ore is processed. Such reactions can explain challenges in producing high quality nickel. Reductive atmosphere with the surrounding gases composed of sulphurous anhydrite has harmful effects on the production of nickel. This is mainly due to solubility of hydrogen as well as nickel oxide in the melted metal. Nickel reacts with carbon monoxide and forms carbide of nickel and nickel oxide which dissolve in the melted metal. Carbon monoxide also dissolves in the melted metal. The presence of carbon dioxide and water vapor in the atmosphere of the furnace impact the decrease of acidity in reductive atmosphere of the furnace. The carbon dioxide reacts with nickel and forms nickel oxide and carbon monoxide. Water vapor reacts with nickel and forms hydrogen and nickel oxide that have negative impact on the structure of nickel and its alloys. In this paper the analytical and experimental analyses are proposed that lead to minimization of the negative effects of gasses and humidity in the melting process. As the practical example, the electrical furnace in Drenas is analyzed.1. The Load and Its CompositionThe basic function of the rotational furnace is drying and reductive roasting of the ore which directly is loaded into the electrical furnace for melting. It is important to mention that the degree of roasting and pre-reduction of iron-nickel oxides is reached if the roasting process of the load in the rotational furnace is done at the temperature of 900°C to 1000°C, with the reductive atmosphere in the furnace and with minimal amount of oxygen in the processing gas. The optimal process of roasting and pre-reduction of the load in its mass is around 13 wt%. With the removal of the humidity and the sterile pare of the ore, with the positive impacts in utilization of the thermal and electrical energy in the melting process in electrical furnaces."

Jan 1, 2013

By Jong Hyeon Lee, Go-Gi Lee, Chang-Kyu Lee, Hong Youl Ryu, Sung-Koo Jo

This study deals with research on the reduction process of neodymium oxide by molten salt electrowinning. Neodymium fluoride and lithium fluoride electrolyte were used for feed stock of electrolyte and neodymium oxide was added as precursor. Cell current was confirmed that cell potential was applied as constant potential of 4.5V. Argon gas injection into the electrolyte was carried out to confirm convection effect on current efficiency. Applied current was gradually decreased without argon flow, but applied current was kept within a certain range with argon flow in electrolyte.

Jan 1, 2015

By Liangying Wen, Xuewei Lv, Yuelin Qin, Feng Zhu, Guibao Qiu, Chenguang Bai, Meilong Hu, Shengfu Zhang

"The COREX process is the first reduction ironmaking technology with coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal and some coke. In order to increase the utilization of fine coal, reduce coke consumption and enhance the competitiveness of the technology, the combustion behavior of pulverized coal injection in melter gasifier is studied experimentally. The results show that the combustion rate of PCI increases with the increase of temperature. And the combustion rate increases with decreasing coal particle size. Compared bituminous coal with anthracite, the former’s burning ratio is higher than the latter in the same granularity. The combustion effect is remarkable when coal blend of bituminous coal and anthracite with the smaller particle size is pulverized in COREX process.IntroductionThe COREX process is the first reduction ironmaking technology with raw coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal [1-3]. However, the proportion of lump coal in raw coal is very small, and it is avoidless to produce fine coal because of mechanical coal cutter and storage and transportation process, so it is important to resolve utilization of fine coal in COREX ironmaking process in order to energy conservation and reduce the cost of hot metal [4]. Currently, Coal briquetting technology is adopted to utilization of fine coal in COREX process [5], but coal briquetting system has high investment cost and requires feasible adhesive agent. The pulverized coal injection (PCI) into a blast furnace is being used on a global scale to improve the stability and reduce the cost of blast furnace operations [6]. The successful development of PCI in blast furnace is contributed to pulverized coal in COREX melter gasifier. However, it is different in PCI process between COREX melter gasifier and blast furnace, and the differences are as follows: firstly, The air is injected into blast furnace, which temperature is about 1200 ?, but in COREX melter gasifier the normal temperature oxygen is blasted, so PCI in blast furnace begin burning in blowpipe, but the combustion of PCI in COREX melter gasifier is only in raceway. Secondly, the racway of COREX is smaller than that of blast furnace of the same size. So, the combustion behavior of PCI is complex in COREX melter gasifier, which is not use for reference."

Jan 1, 2012

By V. Ramachandran

Under the Resource Conservation and Recovery ACT (RCRA), generators of listed or characteristic hazardous wastes must find satisfactory means for disposal. of wastes. Initially, for many this meant landfills and deep-well injection. Until recently, mining and metallurgical by-products have largely been exempt from RCRA, but now are coming under its jurisdiction. With the increasing closures of landfills, companies in the U.S. such as electroplaters, miners, metallurgical plants and others are turning to recycling as an alternative to treat their wastes. While the cost of recycling has been challenging, the long-term economics prove attractive because recycling interrupts the cradle- to-grave responsibility for the waste generator. The present paper describes the recycling of hazardous wastes at ENCYCLE/TEXAS. Encycle extracts marketable metals from metal-bearing sludges and wastewater using hydrometallurgical processes borrowed from the mining and metallurgical industry.

Jan 1, 1994

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities&apos; control. The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b)process chemistry c )discharge options and recovery of treated water and d) sludge disposal. The long term goal of any smelter and/or refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By Anxiang Wang, Kunhua Wu, Yifu Li, Junjie Xu, Yongnian Dai, Bin Yang, Lingxin Kong

In this study, the saturated vapor pressures of tin (Sn) and antimony (Sb), the separation coefficient and the vapor-liquid phase equilibrium of Sn-Sb alloy were theoretically analyzed, which demonstrate that it is possible to separate Sn and Sb by vacuum distillation. The process parameters of vacuum distillation, including the distillation temperature, distillation time and alloy mass (thickness of raw materials) on the direct yield of Sn and the content of Sn in liquid phase were investigated by using single factor experiments. The preliminary results show that the direct yield and the content of Sn are 98.77 wt.% and 96.01% with the optimized distillation conditions of a distillation temperature of 1473 K, a distillation t ime for 45 min and a Sn-Sb alloy mass of 125 g ( thickness o f 8 mm). The distillation parameters in the study provide effective and convenient conditions on separation of Sn-Sb alloy.

Jan 1, 2016

By Robert Matusewicz

Ausmelt Technology has been applied to the recycling of spent pot liner (SPL) generated from primary alnminum production. The process is centered on the Ausmelt furnace, in which the SPL is converted under high temperature, oxidizing conditions to an HF containing gas stream and inert slag. fluorine is recovered from the SPL as HF gas and is concentrated and used to manufacture AIF) for recycle to the aluminum smelters. Approximately 87% of the fluorine can be recovered and converted to AIF), with the remainder being effectively tied up in the by product slag. Cost projections show that the recycling process will be competitive with other processes for SPL. The production and recycling of AIF) provides available credit that significantly offsets the operating cost of the facility. Ausmelt Technology for recycling of SPL is currently being marketed in North America by Ausmelt Technology Corporation in Denver, Colorado, and in the rest of the world by Ausmelt Limited of Dandenong, Australia.

Jan 1, 1996

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By Byung-Su Kim

The reaction between calcium sulfate and hydrogen is of interest both as a means of regenerating calcium sulfide as a reductant of sulhr dioxide to elemental sulhr and for producing elemental sulhr from gypsum. This reaction was investigated using a thermogravimetric analysis technique in the absence and presence of nickel catalyst. The reaction temperature was varied between 973 and 1153 K, while the hydrogen partial pressures of 12.9 - 86.1 kPa were utilized. At 1073 K and a hydrogen partial pressure of 86.1 kPa, 60 % of the original calcium sulfate in the absence, and 95 % in the presence, of the nickel catalyst was converted to calcium sulfide in one hour.

Jan 1, 1999

By J. D. Sunderkötter, M. F. Stroosnijder, V. A. C. Haanappel

"TiAI-based intermetallic compounds have attracted considerable interest as structural materials for high-temperature applications due to their low density and substantial mechanical strength at high temperatures. However, one major drawback hindering industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 °C. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium, and of the effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of such materials.Extended AbstractIntroductionTiAI-based intermetallics are being considered as construction materials for high temperature components, e.g. in aircraft and car engines, due to their low density and substantial mechanical strength at high temperatures, see e.g. [1,2]. The best ductility can be attained with alloys consisting of y-TiAI with around 5-15 vol.% Q2-Ti3AI. However, one major hindrance to industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 aG. In spite of their high aluminium content, TiAI-based intermetallics do not generally form long-lasting protective alumina scales. After longer exposure times the scales, which are initially rich in alumina, deteriorate and scales consisting of mixed alumina and titania predominate, with high growth rates similar to pure titania.It is not the intention of the present paper to present a general overview of the high temperature oxidation behaviour of TiAI based intermetallics, for which the reader is referred to the literature [3,4]. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium. The effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of these intermetallics will also be considered."

Jan 1, 1996

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014