Search Documents

By Bin Zhu, Mingmei Zhu, Hong Zhou, Xiaofei Dou, Bin Xie, Yu Wang, Tiancheng Lin

In this study, the formation of 2CaO·SiO2 and 3CaO·P2O5 solid solution (nC2S-C3P) in hot metal dephosphorization process is discussed. The variations of CaO and SiO2 mass, both in nC2S-C3P solid solution phase and liquid slag phase with increasing P2O5 mass in CaO-SiO2-FetO-P2O5 slags were calculated using Factsage software. CaO-SiO2-FeOt-P2O5 slag containing up to 18 % P2O5 was melted at 1823 K then cooled to 1673 K. The contents of CaO and SiO2 both in the solid solution phase and liquid slag phase of quenched samples were observed and analyzed by SEM/EDS. Both the calculated and experimental results show that the contents of CaO and SiO2 in the solid solution phase decreased, just opposite in the liquid slag phase, with increasing P2O5 content in the slags. Formation mechanism of nC2S-C3P solid solution in the slags was derived based on the ionic structure theory of molten slag. The SiO4 4- in the nC2S-C3P solid solution can be replaced by PO4 3- in the liquid phase resulting in the increasing of free Ca2+ and SiO4 4- in liquid phase.

Jan 1, 2015

By G. S. Hill

A large amount of the stereological error associated with liberation studies can he eliminated by assessing areas instead of linear intercepts. The presentation of a simple geometrical model as a stereological 'worst case' allows calculation of the worst possible grade/recovery curve for a given assemblage of areas. The true results are expected to lie in the window between this worst case and the hest possible case, represented by uncorrected data. The width of this window typically corresponds to an error margin of about 5% grade at a given recovery. An indication of where the data lies within the range of possible grade/recovery results may he obtained from a qualitative analysis of the locked section complexity. Assemblages consisting of texturally complex locked sections (ie. containing many mineral nuclei) are likely to exhibit minimal stereological bias and therefore will tend to lie close to the uncorrected side of the grade/recovery window.

Jan 11, 2011

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil. One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester. Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e .? in flash combustion mode. The velocity. temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data. this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester, Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e., in flash combustion mode. The velocity, temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data, this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"Drying (water removal) prior to smelting is always economically feasible. Unnecessary heating of vapour can thus be eliminated resulting in savings of5-15 MUSD every year.Thermodynamically removal of one ton of water out of copper concentrate at 100 °C (with 10 % moisture) requires approximately 3150 MJ/tH2o, consisting of heating of the water (377 MJ), heating of the concentrate (509 MJ) and water evaporation (2260 MJ). This is quite independent of the selected drying technology. In reality some more heat is needed as higher temperature is practiced to enhance the drying performance and to reduce the equipment size.Major nominator in drying energy efficiency is amount of gases, which depends greatly on the drying technology. Dryers based on direct heating with fossil fuels have high gas flow rates, and thus they require additional energy of about 1400-1600 MJ/tH2o, compared to indirect modemsteam drying at 250-400 MJ/tH2o.Significant benefits in energy consumption (900-1300 MJ/tH2o) with additional potential for a bonus profit of 2-4 MUSD/y year, together with full elimination of some 40 000 tpy CO2 per mid-size dryer is available by selecting sustainable, energy efficient steam drying.IntroductionRemoval of water from the concentrate is very energy intensive thus having a significant environmental impact. However, drying prior to smelting is always economically feasible and very often viable also from the perspective of process operations. This environmental impact of drying can, however, be decreased or even fully eliminated with proper selection of the drying technology.Energy incorporated in drying consists always of a number of phases like liquid (water), solids (concentrate) and gases (water vapour, purging I dilution air, combustion gases). Each phase is heated to a specific temperature during the drying process.Heating of water, heating of the concentrate and water evaporation consumes more or less the same amount of energy despite of the drying technology (3150 MJ per ton of water). In conventional drying this amount of energy is achieved by combustion of fossil fuels wirg subsequent CO2 emission. Alternatively, chemical energy derived from sulphide smelting can be utilized in a form of steam thus generating zero emission ofCO2, in modem steam drying."

Jan 1, 2012

By Francois Barthelat, Sam Goroshin, David Frost, Alexander Cappozi, Atefeh Nabavi

"In this study, a novel chromium–chromium sulfide cermet was produced by self-propagating high-temperature synthesis (SHS). Conventional techniques for manufacturing metal sulfides are complex, environmentally harmful, and not suitable for producing complex-shape articles. To overcome these disadvantages, a new method for the preparation of the metal-sulfur precursor charge is proposed, which can be described as reactive casting. The first cermet samples produced with the SHS process were found to be very porous, brittle, and have low mechanical strength. The possible sources for the generation of porosity were identified and analyzed and the process for manufacturing the cermet was modified. By improving the manufacturing process, the porosity inside the produced cermets was reduced from 70% to 12%.IntroductionMetal sulfide composites are in high demand in the chemical, metallurgical, and electrical industries because of their valuable characteristics such as hardness, semi-conductivity, electroluminescence, infrared transparency and catalytic properties. Current manufacturing methods for metal sulfides usually involve one of two different principal methods, including a complex multistage wet chemical process involving the precipitation of the corresponding salts from an aqueous solution with hydrogen sulfide, or hot sintering of the respective elemental reactant powders in a resistive furnace in a high-pressure inert or hydrogen-sulfide atmosphere [1, 2]. These conventional methods for synthesizing ceramic metal composites are complex, extremely time and energy consuming, environmentally harmful, and rarely able to manufacture articles with complex shapes. Therefore, in order to overcome these disadvantages, self-propagating high-temperature synthesis (SHS) was considered as an alternative method that offers significant improvements over the traditional cermet manufacturing methods [3]. SHS, which is a relatively new and attractive method for producing a wide range of advanced materials, is based on the self-sustaining feature of the highly exothermic reactions of the reactants. The SHS process results in high product purity, since the high temperatures generatedin the reaction cause any impurities to volatilize [4, 5]. SHS has low energy consumption and doesn’t require an external energy source and complex equipment, and it is self-contained [1, 5]. Since combustion synthesis has low power requirements, it is one of the few methods of materials synthesis that is feasible in outer space. Also, the process has a low cost and is capable of directly synthesizing articles with the desired shape, size and structure [5, 6]. The chemical reactions associated with SHS are typically completed in a few seconds leading to the formation of the condensed product. The high reaction rates and relatively rapid cooling in SHS reactions can avoid undesirable grain growth in products which often occurs with the conventional sintering method [3, 5, 7]. The traditional method for sample preparation in the SHS technique is to compact the reactant mixture powders in a steel die by a press to a typical density of about 80% of the theoretical maximum value, before igniting the mixture [8]. This method requires a large compression force to increase the green density and to minimize any pores in the green compact. To overcome these disadvantages, a new method for the preparation of the precursor charge in metal-sulfur by SHS is proposed which can be described as melt casting of a reactive mixture, or reactive casting in short."

Jan 1, 2012

By J. W. Matousek

Cobalt behavior in pyrometallurgical processes is traditionally analyzed using slaglmatte distribution coefficients as functions of matte grades or matte iron contents. L(s/m) = (%Co) I [%Co] = f [%CuNi] or f [%Fe] The method is inconvenient to use in predictive mass balance work because of the interdependence of assays and mass quantities. An alternative procedure is proposed based on cobaltliron ratios for slags and mattes: Js = (%Co) / (%Fe), Jm = [%Co] / [%Fe], and J, = b + m [Jm]

Jan 1, 1993

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By Hui Zhang

The leaching behavior of palladium powder in aqueous solutions containing NaCI or N'H4Cl was investigated. Cupric ion was used as an oxidant for the dissolution reaction. The effect of a number of leaching parameters such as temperature, concentration, stirring speed and surface area on the leaching rate was studied. The leaching system containing chloride and cupric ion was found to be very effective for the dissolution of metallic palladium. Based on the experimental results the overall leaching rate was believed to be controlled by a chemical reaction step. The dissolution rate of palladium was found to be first order with respect to the concentration of cupric ion and second order with respect to the concentration of chloride.

Jan 1, 1996

By Chao Du, Xiaohui Ning, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

"TiCxOl-x solid solutions were synthesized by sintering a mixture of titanium carbide and titanium monoxide at 1600 °C. The corresponding structures and morphologies of the TiCxOl-x solid solutions were characterized by XRD and SEM. A series of tests has been performed on the electrochemical dissolution behavior of TiCxOl-x solid solutions in NaCl-KCl molten salt. The influences of synthesis time and electrokinetic parameters on the anodic dissolution behavior were also investigated. The results showed that TiCxOl-x solid solutions can dissolve as Tin+ into alkali chloride melt. Titanium ion species dissolved from TiCxOl-x solid solutions changes between Ti2+ and Ti3+ depending on the applied potential. The tail gas on the anode was monitored by a mass spectrometer. It was found the synthesis time significantly affects the components of the anodic gas.IntroductionTitanium and titanium alloys have been desired greatly because of their many uses. The critical factor that restricts the range of uses for Ti is its high cost of extraction. The primary titanium metal, sponge titanium, is still produced industrially worldwide by a process invented by Dr. Kroll in the 1940s[1] •Since the early 1970s, the research focus of the titanium industry has been directed towards developing a continuous process to produce high purity titanium at low cost. [2-10] Of the many alternative methods that have previously been investigated, the electrolytic process has been considered a promising method for titanium metallurgy [4-10]. Recently, several electrolysis and related methods such as the PFC-Cambridge process[11-15], calciothermic reduction[16-18], USTB [19,20] and MER[21] process were extensively investigated.The USTB process is a new approach where the pure titanium can be directly obtained by the electrolysis with an anode of titanium oxycarbide in molten salts[19, 20]. The titanium oxycarbide was produced by carbothermal reduction of titanium dioxide under vacuum at a temperature"

Jan 1, 2011

By Shekhar Bhansali, Shyam Aravamudhan

"This paper reports on the design and simulation results of a silicon bulk-micromachined diaphragm-type piezoresistive pressure sensor capable of operating linearly over a wide dynamic range (0-1000 meters of water). The piezoresistor elements of the sensor are arranged in a wheat stone bridge configuration to achieve a higher output response. Simulation results (output voltage and sensitivity analysis) obtained using coupled MemPZR-MemMech module of the CoventorWare2003 Finite Element tool are presented. The effect of diaphragm size, diaphragm thickness and thickness of the piezos on output sensitivity were analyzed and optimized to get a linear response over the wide dynamic range.IntroductionThe physical and biological processes in the ocean are critically influenced by ocean parameters (pressure, salinity and temperature). Thus there is a need to develop inexpensive and reliable sensors to continuously measure large volumes of sea-space over long time spans. A key component in any such system will be a pressure/depth sensor. This sensor is routinely employed in marine applications such as wave and tide gauges, tsunami detection, platform leveling etc. More significantly, pressure measurement is needed for depth determination. Depth sensors are vital for remote operated vehicles (ROVs), profiling instruments and towed arrays.Several techniques have been routinely used in the past to measure pressure in the marine environment [1-3]. In general, the pressure sensor design is based on a flexible membrane as the spring element for the sensing pressure [4]. The deflection of the membrane, induced by the applied pressure, is converted into an electrical output through a component that is sensitive to diaphragm deflection (capacitive coupling) or associated stresses (piezoresistors, strain gauges). The temperature compensated pressure measurement can be readily converted to depth using"

Jan 1, 2004

By S. B. Bortnikova

This paper presents the results of an investigation of the gold-silver oxidized ores at the Salair mine. West Siberia. High losses of precious metals during primary ore processing are the result of outdated technology that is not suited to treat the present ore compositions. The main mineralogical forms of gold and silver and their confinement to different grain size fractions have been determined. About 50% of gold in the slime fraction and 60% of the silver in the form of acanthite that are scattered from the secondary minerals are lost to the waste. The results of these investigations have provided the basis for the recommendation of a new technological process to upgrade the current practice of the gold extraction plant and for methods to reprocess the concentrates.

Jan 1, 1995

By Andriy Burbelko, Daniel Gurgul, Wojciech Kapturkiewicz, Marcin Gómy

"The mathematical model of the globular eutectic solidification in 2D was designed. The proposed model is based on the Cellular Automaton Finite Differences (CA-FD) calculation method. The model has been used for studies of the primary austenite and of globular eutectic grains growth during the ductile iron solidification in the thin wall casting. The model mentioned above takes into account, among other things, non-uniform temperature distribution in the casting wall cross-section, kinetics of the austenite and graphite grains nucleation, solute diffusion and non-equilibrium nature of the interphase boundary migration.Some aspects of stochastic nature of the solidification processes are taken into account. The results of the CA solidification modeling have been shown, that differences between cooling curves obtained in the same conditions of the casting solidification may be a result of the stochastic nature of the grain nucleation.The results of modeling were compared with the experimental microstructure. The model is well worked for thin walled ductile iron casting, for fast solidification process.IntroductionNodular graphite cast iron, also known as ductile iron (DI), has major applications in critical engineering parts due to its mechanical properties and castability. The mechanical and physical properties of this material depend on the shape and number of the graphite grains andmicrostructure of the metallic matrix.Solidification of DI was a subject of many computer modeling programs described in literature [ 1-5], in which the stationary conditions of carbon diffusion in austenite is pre-assumed. Recently, a tendency for production of thin-walled castings has been observed [ 6-8]. In this technology, the process of the fast solidification may be very far from equilibrium and steadystate conditions [9].The purpose of the present work is a two-dimension model development for simulation of the DI structure formation during the solidification in the condition of non steady-state temperature and diffusion fields in the thin-wall casting.Model of process The CA-FD is one of the known methods of the simulation ofmicrostructure formation during the solidification [ 10, 11]. In the CA microstructure modeling the outer grain shape is the result of the simulation and does not superimposed beforehand. The model development for a onephase microstructure evolution is a subject of the numerous researches [12 -23]. Model of the eutectic solidification of DI in the uniform temperature field and superimposed cooling rate is known [24]."

Jan 1, 2013

By C. M. Antony

The galvanizing process involves the use of accessory equipment in a series of aggressive environments including zinc ammonium chloride flux, molten zinc at 45S°C (850°F), and acid for stripping of adherent zinc. An Fe-Ni-Cr-Co alloy has been identified which combines excellent strength and resistance to molten zinc and acid attack making it suitable for accessory equipment. The alloy was field tested by a commercial galvanizer as basket material and was found to provide improved life compared to original low-alloy steel baskets while cross-section thickness was reduced 44%. Additionally, other associated processing cost savings were realized.

Jan 1, 1992

By B. J. Jody

At Argonne National Laboratory, we have been developing a potentially economical process to recycle automobile shredder residue (ASR). We identified three potentially marketable materials that can be recovered from ASR and developed technologies to recover and upgrade these materials. We built and tested a field-demonstration plant for recycling polyurethane foam and produced about 2,000 lb (907 kg) of recycled foam. Several 300-lb (I36-kg) samples were sent for evaluation and were found to be of marketable quality. We are also preparing for a large-scale test in which about 200 tons (181 tonnes) of ASR-derived fines «0.25 in. [<0.62 cm]) will be used as a raw material in cement making. A major cement company has evaluated small samples of fines prepared in the laboratory and found that they meet its requirements as a substitute for iron ore or mill scale. We also produced about 50 lb (23 kg) of recycled acrylonitrile butadiene styrene (ABS) from obsolete automobiles and found that it has properties that could be readily upgraded to meet the specifications of the automotive industry. In this paper, we briefly discuss the process as a whole and summarize the results obtained from the field work on foam and fines recycling.

Jan 1, 1996

By Felipe Daroch, Maria C. Ruiz, Rafael Padilla

Copper concentrates with high arsenic contents must be pretreated before conventional smelting to prevent environmental pollution with arsenic compounds. In this work, experimental results concerning the selective removal of arsenic and antimony from copper concentrates are presented. The process consists of an alkaline digestion using concentrated NaHS-NaOH solutions to transform the arsenic and antimony sulfides into soluble compounds. A water leaching follows the digestion to dissolve the arsenic and antimony, leaving clean copper sulfide solid residues. The laboratory scale tests were carried out using a copper–arsenic concentrate with 15.05% As and 1.42% Sb. The results showed that the most important digestion variables were temperature and concentrations of NaHS and NaOH. Over 97% of arsenic and 92% of antimony could be removed in 10 min of digestion using 8.9 M NaOH and 100% excess of NaHS at 80 °C. The subsequent water leaching was performed at 80°C for 20 min.

Jan 1, 2015

By Tetsuya Uda

Our recent achievements of rare earth separation technique[1,2] and new process idea for rare earth magnet recycling[3] are reviewed, (1) Binary chloride mixtures of rare earths were separated by a new selective reduction-vacuum distillation process. According to our experimental results, apparent separation factors were 8.1 for the Pr-Nd chloride mixture and 570 for the Nd-Sm chloride mixture. These values are much higher than conventional solvent extraction methods. (2) A study of recycling process of magnet sludge was carried out. The rare earths in the neodymium magnet sludge were extracted by chlorination with FeCI2, An activated carbon was used as a de-oxidation reagent Metallic iron in the sludge was not chlorinated because the iron monochloride is not stable, The extracted rare earth chlorides were easily separated from Fe-alloy and the excess of FeCh by vacuum distillation, 96 % of neodymium and 94 % of dysprosium in the sludge were extraeted into chloride phase, By the vacuum distillation, a mixture of neodymium and dysprosium trichlorides of 99.2 % purity was recovered, On the other hand, the rare earth chlorides can be converted to the corresponding oxides by a pyrohydrolysis reaction accompanied by a formation of HCl gas, The HCI gas can chlorinate metallic iron to FeCh, Therefore, a new recycling process for rare earth magnet waste can be realized as a chlorine circulation type process. During the process, only carbon and water are consumed and there are no toxic pollutants, Moreover, the obtained rare earth oxide can be directly used as raw material in the conventional oxide electrolysis process,

Jan 1, 2003

By R. P. King

The essential features of an image analysis system for the measurement of mineral liberation are described. Good procedures for image acquisition and image processing prior to image analysis are defined. The basic stereological methods for the measurement of volume fraction, surface area per unit volume, particle size distribution and liberation spectra are given. The appropriate methods for fractal correction when measuring perimeters of irregular features and for frame correction when measuring linear intercepts are developed. Practically useful and accurate procedures for the stereological correction of particle size and liberation distribution methods are given.

Jan 1, 1995

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By M. Soltanieh

The liquidus surface? and tie-lines in the nickel-cobalt-sulphur ternary system have been determined between 1<273-1573 K. The experiments were conducted by equlibrating the liquid sulphide with the metallic alloy phase. The liquid sulphide phase was sampled and chemically analyzed. The alloy was analyzed by electrol} microprobe. Combining the present results with the.avai1abl~ literature data, the thermodynamic properties of this system were calculated.

Jan 1, 1998