Search Documents

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite / Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades. EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized.

Jan 1, 2003

By Thomas W. Chapman, Shi-Chern Yen, I-Min Lu

"An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore, local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces.The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.IntroductionRemediation of soils contaminated with toxic chemicals is a difficult and expensive task. Washing or leaching are not particularly effective if the contaminate is sequestered in small pores; hydraulic flows of water pass through larger pores leaving the smaller pores relatively untouched. Electro-osmosis appears to be the most promising new technology for removing heavy metals and organic substances from contaminated soils (Segal, 1980; Hamed et al., 1991, Masliyah, 1994).Electro-osmosis is one of several electrokinetic phenomena that occur through the interactions among an electric field, fluid motion, solute adsorption, and the existence of a net charge on a solid-fluid interface (Newman, 1991, Masliyah, 1994). Electro-osmosis refers to the fluid flow in a porous medium that results when an electric field acts on the mobile region of the electrical double layer, the solution-side region of charge separation that exists at the pore walls."

Jan 1, 1996

By Robert Mensah-Biney

The loading characteristics of gold-tetrabromide species onto a weak-base resin, PAZ-4, were evaluated using a completely mixed batch reaction system. The time. to attain equilibrium loading was substantial, on the order of several days. However, abnormally high loading capacity values of 15 to 20 meq Au/g dry resin (1000 to 1300 kgAu/tonne) were attainable in 24 hours. The loading of gold-bromo species by P AZ-4 was visualized as consisting of two processes: (i) the rapid adsorption of [AuBr4r species by simple ion exchange mechanisms and (ii) reduction of [AuBr4r to metallic gold by an electron exchange mechanism. Elution of gold from loaded resin was feasible provided the resin had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the loaded resin. For the high loading capacities observed this option would appear to be cost effective.

Jan 1, 1991

By Maria K. Kojo

The interaction between various slags and a nickel concentrate containing pyrite, pentlandite, and violarite were investigated by submerging concentrate pellets in molten slags. The slags were contained in MgO-A12O3 spinel crucibles. The slag oxidizes the iron sulfides in the concentrate, resulting in a nickel matte. The amount of S02 gas formed during reaction was measured to determine the oxidation reactivity of the slags. The experimental variables included temperature, the ferric/ferrous ratio of slag, and other slag properties such as the FeO/SiO2 ratio and the MgO and NiO contents. The reactivity of the slag depended in a complex manner on its oxidizing power, viscosity, and interfacial tension. The slag composition for the greatest reactivity was determined to be Fe3+/Fe2+ = 0.3, Fe/SiO2 = 1.3, and % MgO = 2. This slag, however, caused substantial foaming. Increasing the MgO content to 10% or replacing it by 5% MgO + 8% NiO eliminated at a slight decrease in reactivity. The implications of the findings from this work in the bath smelting of nickel sulfide concentrates are discussed.

Jan 1, 1995

By Balladares V. Eduardo

Most of the arsenic contained in copper concentrates is removed in the gas phase during the smelting and converting processes and, according to recent environmental regulations, it is required to fix it in a solid stable form. In this regards, ferric arsenate has been reported as thermal and aqueous stable compound. Therefore, various alternatives for treating gas containing arsenic were considered in this work. From data obtained at laboratory scale on fixation of arsenic using iron oxide, a new process to treat copper concentrates containing arsenic was evaluated. The effect of temperature, oxygen potential and the sample porosity on the fixation of arsenic contained in a gaseous stream was studied, and the iron oxide converted into ferric arsenate was up to 10%. The obtained results suggest a new alternative for gas treatment with an interesting and attractive technical development. The arsenic was retained as ferric arsenate with thermal and aqueous stability, and it allows a safe disposal keeping the environmental restrictions. The kinetics parameters are used to scale up laboratory results to higher processing rates.

Jan 1, 2005

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By George A. Calboreanu

In order to overcome drilling and tapping of high hardness wear resistent material in slurry pumps, most of time mild steel inserts are mounted in the mold and after pouring they become an integrated part of the casting. This process is limiting the size and design possibilities of slurry pumps and efforts were made to drill and tap the hard iron itself. The paper will present practical results obtained in drilling and tapping Cr-Mo wear resistent material with hardness in excess of 700 HBN. The life time of the slurry pump parts used in hazardous waste fuel transportation with high slurry velocity and 15% solid loading some of it being quartz, increased 2.5 to 6 times.

Jan 1, 1996

By E. Krystad, G. Tranell

"The kinetics of boron removal from liquid silicon during slag refining, as a process step in the production of solar grade silicon, has been investigated by means of small scale mass transfer experimental series at 1600°C, using a graphite crucible. The slags were SiO2-CaO based, with or without addition of approx. 19 wt% MgO. Experiments were carried out at slag-metal ratios of 1 or 2, where the silicon initially contained approx. 250 ppm boron. The metal-slag mass transfer coefficients for boron were found to be in the order of 1-3 · 10-6 m/s and were largely influenced by slag composition. The mass transfer rate was higher for the MgO-containing slag than the slags without MgO. The final equilibrium distribution of boron between metal and slag, LB, was determined to be in the order of 2.3-3.3.I. INTRODUCTIONRecent years have seen a race in industry and research aimed at obtaining a reliable metallurgical route for production of silicon for solar cells (SoG-Si) from metallurgical grade (MG) silicon. Metallurgical routes can successfully challenge the traditional chemical routes for production of SoG-Si if they generate metal of sufficient purity while being less expensive in terms of production cost and energy consumption. Efficient removal of boron is one of the greatest obstacles in the refining of silicon by a metallurgical route, because the segregation coefficient of boron in silicon makes directional solidification unfeasible; in addition, the vapour pressure of boron is not high enough for removal by vacuum refining. However, the thermodynamic properties of boron makes removal from silicon by oxidation possible, and thus the process of slag refining of silicon has been receiving increasing attention as a method for boron removal."

Jan 1, 2012

By Animesh Jha, Chris Dometakis

"Without the use of a flux, only a poor dispersion of ceramic phase can be achieved. A molten-flux-assisted ceramic phase dispersion technique for producing aluminium alloy metalmatrix composites has been developed. In this paper, we report the physical chemistry for the dispersion of TiB2 in molten aluminium. In particular, aspects of the interfacial energy and the thermodynamics of the dispersion reactions are briefly discussed for enhancing the volume of dispersion phase in the molten metal and for controlling their morphology. This investigation also addresses the role of molten flux in the fabrication of AI-alloy mmc using a casting technique. The morphological aspects of the dispersion are explained on the basis of the classical theory· of nucleation.IntroductionMetal matrix composites (MMCs), have long been recognised as an important class of material due to their greater wear resistance, specific stiffness and temperature capability when compared to conventional monolithic alloys. Particulate reinforced composites produced by melt casting techniques have been amongst the first MMCs to achieve commercial market viability. The advent of melt mixing techniques such as the Duralcan™ process have enabled low cost, easily fabricated composites based on the AI-SiC and AIAlz0 3 systems to be produced. In this process, uncoated ceramic particles with diameters 10ltm and larger, are incorporated into conventional monolithic alloys with reinforcement levels up to 25 volume percent. The AI-7Si-SiC metal-matrix composites have good wear resistance, high strength, low density and high thermal conductivity. The combination of these physical and mechanical properties has become a major attraction for the fabrication of light-alloy composite disc rotor brakes for the automotive sector2. However, in silicon-free alloys, SiC is thermodynamically unstable above the composite melting point and is extensively attacked by the melt to form aluminium carbide3 :"

Jan 1, 1996

By J. W. Lyman

Nickel-metal hydride (Ni-MH) battery electrodes have been developed as a substitute for cadmium-containing negative electrodes. Use of Ni-MH electrodes offers enhanced electrochemical properties in many instances as well as reduced environmental toxicity. Rechargeable batteries using Ni-MH electrodes are also strong candidates for electric vehicles. During the production and secondary reclamation of these battery types, recycling procedures will be needed to prevent environmental impact caused by these wastes as well as to recover the value inherent in the scrap. The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical technology that separates and recovers purified metallic components from Ni-MH battery scrap of two types, AB, and AB,. An investigation of acid dissolution and metal recovery techniques has determined several processing alternatives that may be used to promote the successful recycling of much of the battery fabrication scrap and eventual secondary scrap. Although recovery techniques have been identified in principal, their applicability to mixed battery waste stream and economic attractiveness remain to be demonstrated.

Jan 1, 1995

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By Animesh Jha

The carbothermic reduction of chalcopyrite has been studied in the temperature range 1073 to 1273K in presence of lime. The role of lime during the reduction process is explained and the phase equilibria leading to the metallisation of copper and iron are discussed. The effect of coal and carbon monoxide on the reduction process have been studied and the rate governing steps are identified. This investigation also cites examples of possible mechanisms of physical separation of metallic Cu from iron during the reduction process.

Jan 1, 1992

By Junbiao Liu

Rutile is mostly produced from placer sands. Its beneficiation from primary deposits has rarely been investigated. However, there is interest in primary deposit because of the depletion of sand deposits. The Zaoyang deposit in China is the only rutile primary deposit currently mined. The plant employs a Tabling-Magnetic process which recovers only 20% Ti02 at a grade of 87%. This study shows that significant improvement on the recovery (52% at the same grade) can be achieved. This study includes a detailed mineralogical examination and the development of a processing flowsheet of the ore. The gangues are primarily amphiboles, garnets, zoisites, and chlorites. The liberation of rutile occurs at about 200 mesh. Gravitational, flotation, and magnetic separations are all employed in the process developed, depending on the mineral characteristics and experimental results. The flotations circuit utilizes benzyl arsonic acid to float rutile and sodium fluosilicate to depress the gangues. This is a new reagent scheme for rutile flotation.

Jan 1, 1989

By Joseph Bloch

The hydriding of bulk metals and alloys is a gas-solid reaction in which a hydride product layer is initially nucleated adjacent to the gas-solid interface and continues to grow until a complete transformation of the parent (a) phase into the hydride phase. The combination of measurements of the overall hydriding kinetics of samples having defined shapes and dimensions, together with examinations of partially hydrided samples, enables the presentation of the reaction rate in terms of an appropriate reaction model. A common and important type of topochemical development of the hydride in bulk metals and alloys involves a hydride layer formed on the metallic surface. The continuity of the layer can affect the reaction rate. The rate of hydrogen absorption in a sample, in the presence of a hydride layer, is usually analyzed using a model combining several sequential steps in which the hydrogen is transferred from the gas phase into the reaction site. Coupling the flux equations across the layer under proper steady state conditions, results in a complex rate equation in which the steady state rate of hydrogen absorption (proportional to the hydride layer velocity) is expressed in terms of the pressure, temperature, the rate constants of the sequential steps and the critical concentrations of hydrogen in the hydride. Generally, the rate constants of the individual microscopic processes are comparable in magnitude, so that the overall rate is not controlled by any of the specific sequential steps. However, there are two limit cases related to the first stage, the adsorption, for which the general rate equation is much simpler, namely, the fast and the slow adsorption approximations. Using this limit cases, equations are derived for the steady state hydriding rate of a given system. These equations provide means to anticipate the pressure dependence of the steady state absorption rate under low pressures, close to Peq and under very high pressures. At the low pressure regime both the fast and slow absorption cases yield linear pressure dependence. For the very high pressure range, it is found that the rate become independent of the applied pressure. The rate is given then by a combination of the individual rate constants of the system and the critical hydrogen concentrations. The model is shown to apply in several real cases, such as ZrCo, LaNi5 and titanium.

Jan 1, 2002

By I-Min Lu

An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces. The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.

Jan 1, 1996

By J. E. Clemson

The Black Pine sediment-hosted, disseminated gold deposit is located in Cassia County, Idaho. Gold mineralization occurs in flat-lying zones 50 to 100 feet thick. Total geological ore reserves are 5.6 million tons grading 0.049 oz/t. Ore types include: non-carbonaceous, oxidized ore; carbonaceous, sulfide ore; and carbonaceous, partly oxidized ore. In the oxidized ores, native gold grains commonly occur in porous hematite pseudomorphs that have replaced disseminated framboidal and euhedral pyrite, and this gold should be readily leached by cyanide solutions. Approximately 4 % of the native gold observed in the oxidized ores is locked within gangue and may be refractory to cyanide solutions. Native gold has not been observed in the unoxidized samples, all of which are characterized by primary sulfides. It is suspected that the bulk of the gold mineralization in the sulfide ore occurs as submicroscopic particles within pyrite and will be refractory to cyanidation. It is believed that much or all of the gold observed in the oxidized samples was originally in pyrite but was released and re-precipitated during oxidation. The degree of oxidation of the pyrite and the presence/absence of preg-robbing carbonaceous material is used as a guide in delimiting zones of mineralization amenable to heap leaching.

Jan 1, 1988

By C. A. Silva

Ladle change-over, during continuous casting of steel, initiates transient flow in the tundish which influences the inclusion content and degree of mixing between two consecutive batches of steel. The mixing behavior in the tundish during this period is determined by the casting rate and the ratios of: inflow to outflow during the refilling period; and, the low liquid level relative to the nominal level in the tundish during the transiency. A 3:10 scale water-model of a typical one strand slab caster was operated in conjunction with a tracer technique to characterize the velocity fields for several combinations of these parameters. Steady operation, a limiting case of the transiency, provided a basis for comparison. High-order moments -- skewness and kurtosis -- of the residence time density function have been utilized as signature elements associated with a particular residence-time distribution for the system. A simple mathematical model incorporating the above parameters as well as a characteristic Peclet Number was successful in simulating the features of the transient period.

Jan 1, 1993