Search Documents

By K. Yamada, T. Takaoka, A. Ozeki, M. Yamaga, Y. Kawai, S. Nishioka, Y. Kikuchi

"Recently, smelting reduction of chromium ore in BOF has been actively investigated as a key unit process for an innovative future stainless steelmaking. The prominent feature of this new process route is energy and process saving, and production cost saving. The development is already in the midst of application to the commercial production, however there still remain the following key technologies to be established for the full use of the process. One is a speed up of the reduction of chromium ore to match with sequential continuous casting, and the other is efficient combustion of carbonaceous materials in BOF to reduce their consumption, and hence to assure the steel quality. High degree of post combustion technology and new charging technology, i.e., ore-coal-flux-oxygen mixed injection, could be effective for those two subjects. In 2000 or beyond, the new process would have become quite popular owing to the establishment of those key technologies.Introduction Since stainless steel was invented, its production has continued to expand because of its attractive combinations of functions of excellent corrosion resistance, good formability, a pleasing appearance, and a wide range of strength levels. New types of stainless steels as well as new applications are continually being developed.Compared to the production of ordinary steels (1), stainless steel production (2,3) shows steady growth worldwide, while the former production remains on the same level, as Figure 1 shows. It can be estimated that future production would show further growth since materials consumer demands are more fashionable, or more functional, which could be satisfied by stainless steels.Thus market needs would be met, if it could be produced with reasonable production cost. The emergence of an innovative production technology is then potentially requested as VOD and AOD processes have emerged, which has saved substantial production cost. This paper describes a possibility of a future stainless steelmaking process, which uses the in-bath smelting reduction of chromium ore in BOF, and which would save production as well as energy cost."

Jan 1, 1988

By Baozhong Zhao

Laboratory experiments have been conducted on the removal of As, Sb and Bi from molten copper by SF 6 injection. The results showed that the impurities can be removed by SF6 injection in the? sequence of Sb >As >,Bi and the rate of Bi removal is affected significantly by the concentration levels of As and Sb in the copper melt. Analysis of the experimental data indicates that the impurity removal process is under chemical reaction control rather than by mass transfer of impurity through the molten copper phase. On the basis of experimental results, a kinetic model was developed and the order of chemical reaction and the volumetric chemical reaction rate coefficients of impurity removal were determined.

Jan 1, 1996

By Linlin Wu, Marlen Bertram, Chris Bayliss, Bernard de Gelas, Samantha Jones, Kurt Buxmann

"Environmental management is one of the industry cornerstones of sustainable development. In order to understand fully the environmental aspects associated with the raw material acquisition, production, use, and end-of-life operations of aluminium products, the Aluminium Industry has developed an approach based on Life Cycle Analysis (LCA) methodology.Within this framework, the Primary Aluminium Industry has established a global Life Cycle Inventory (LCI) data set. Inventory flows include inputs of raw materials, energy and water, emissions to air and water, and solid waste.This paper presents the latest LCI data update by the International Aluminium Institute for the year 2010, based on a survey of aluminium plants globally, including bauxite mining, alumina refining, anode production, electrolysis and casting. This update also includes some performance tracking based on the last LCI data collection in 2005, reflecting progress in efficiency and technology, as well as changes in the geographical location of the industry [2010 data pending]. IntroductionIn 2010 the Primary Aluminium Industry produced a total of 41 Mt of aluminium. The International Aluminium Institute (IAI) membership represents approximately 70% of total global production. The industry recognises the importance of co=itting to reducing the environmental impacts of producing primary aluminium, and the significance of working towards a more sustainable future. As part of this co=itment the IAI has developed an in depth Life Cycle Inventory programme, in which data is collected every five years, with supplementary key metrics collected annually.In 2003 the IAI released its first Report ""Life Cycle Assessment of Aluminium: Inventory Data for the Worldwide Primary Aluminium Industry"" based on the year 2000 with an update Report released in 2007, based on 2005 data.This paper presents the latest update for the year 2010 [2010 data pending]. It has been prepared with the same view of collecting all significant Life Cycle Inventory data (raw materials and energy use, air and water emissions and solid waste generated) associated with producing primary aluminium ingot from bauxite ore, with worldwide coverage. The intended purpose of the Inventory Report is to accurately characterize resource consumption and significant environmental aspects associated with the worldwide production of primary aluminium. It reflects the fuct that primary aluminium is a globally traded co=odity."

Jan 1, 2012

By Y. Y. Liu, H. M. Domanus, W. T. Sha

"Casting is fundamental to manufacturing of many types of equipment and products. Although casting is a very old technology that has been in existence for hundreds of years, it remains a highly empirical technology, and production of new castings requires an expensive and time-consuming trial-and-error approach.In recent years, mathematical modeling of casting has received increasing attention; however, a majority of the modeling work has been in the area of heat transfer and solidification. Very little work has been done in modeling fluid flow of the liquid melt. This paper presents a model of fluid flow coupled with heat transfer of a liquid melt for casting processes. The model to be described in this paper is an extension of the COMMIX code and is capable of handling castings with any shape, size, and material. A feature of this model is the ability to track the liquid/gas interface and liquid/solid interface. The flow of liquid melt through the sprue and runners and into the mold cavity is calculated as well as three-dimensional temperature and velocity distributions of the liquid melt throughout the casting process.IntroductionBower et al. (1), in their 1969 review of the evolution of some of the casting techniques, stated that:""The evolution of technology requires alternatives to be available so that choices can be made that lead to changes. The role of solidification science and other disciplines related to casting technology is to develop a better understanding of process and product, so that a wider range of alternatives is possible.Alternatives, whether from science or from invention, must lead to improvements in casting ""utility."" Utility, or economic advantage, must include consideration of total system costs, and final product value. The cost of materials, melt processing and finishing should be optimized with casting costs, since all are part of the production system. It is the favorable relationship between total processing costs and product value that makes a change in casting technology viable, but the best change is not possible unless technology has provided an understanding."""

Jan 1, 1986

By Y. Fautrelle, F. Felten, O. Metais, Y. Du Terrail

"We deal with the prediction of electromagnetically-driven turbulent flows by means of a Large-Eddy- Simulation method (LES). The model is applied in the case of a liquid metal pool submitted to a polyphase linear electromagnetic stirrer. We investigate two cases: (i) the frequency of the magnetic field is equal to 50 Hz; in that case the effects of the pulsating part of the Lorentz forces may be neglected; (ii) the frequency of the magnetic field is low (f= 1 Hz), then the oscillating part of the electromagnetic forces is taken into account. The LES predictions agree well with the mean velocity measurements, as does the standard k-a model. However, as for the turbulent kinetic energy predictions, there is a large discrepancy between the two models. When the oscillating part of the Lorentz forces is taken into account, the computations show that the fluid flow is sensitive to the unsteady part of the forces. We find that the mean velocity is not affected by the fluctuating component of the force. As for the turbulence parameters, the presence of the pulsating part leads to a significant reduction of the turbulent kinetic energy, whilst the turbulence length scale decreases.IntroductionElectromagnetic stirring is commonly used in various metallurgical processes. In continuous casting for example, it may improve the structure of the solidified metal products. Fluid flows generated by electromagnetic stirrers have been extensively investigated (1 ). As for numerical predictions, many works have been published on the subject. In most of the previous works, onepoint closure models have been used. The most used model is the well-known k-i:: model. Those models yield fairly good results as for the mean velocity prediction. However, it has two main drawbacks:(i) the turbulence is not predicted accurately,(ii) it is not well fitted for unstationary flows as well as transitional turbulent motions, where theReynolds number is moderate."

Jan 1, 1999

By Joo Hyun Park, Kyu Yeol Ko

The viscosity of the CaO-SiO2-xMnO-yCaF2 slags (C/S=1.0; x=10, 40%; y=0 to 15%) was measured to clarify the effect of CaF2 on the viscous flow of molten slags at high temperatures. Furthermore, the Raman spectra of the quenched glass samples were quantitatively analyzed to investigate the structural role of CaF2 in a depolymerization of silicate networks. The critical temperature of the slags abruptly increased at 15%CaF2, which was confirmed to originate from a crystallization of cuspidine using XRD analysis. The viscosity of the slags continuously decreased by CaF2 addition in the 10%MnO system, whereas the viscosity of the 40%MnO system was not significantly affected by CaF2 addition. The effect of CaF2 on the viscosity of the slags was quantitatively analyzed using micro-Raman spectra of quenched glass samples accompanying with a concept of silicate polymerization index, Q3/Q2 ratio. A polymerization index continuously decreased with increasing content of CaF2 in the 10%MnO system, whereas it was not affected by CaF2 in the 40%MnO system. Consequently, the bulk thermophysical property of the CaO-SiO2-MnO-CaF2 slags was quantitatively correlated to the structural information.

Jan 1, 2014

By Dalene Joalet Steenkamp

Excavation of industrial-scale furnaces allows for the systematic study of reaction sequences by identifying the different reaction zones within the furnace. In 2013, Transalloys excavated a 48 MVA submerged arc furnace that was used for silicomanganese production using the ore-based route. The excavation method was reported elsewhere as was observations made in terms of refractory wear and modes of electrical energy dissipation prior to excavation. The paper presented here, reports on the process reaction zones observed during the excavation and subsequent phase chemical analyses of a number of process samples obtained during the excavation. The zones identified were a loose burden zone, a dry coke-bed zone, a wet coke-bed zone, a hard build-up zone, and an alloy zone. The results are compared to observations made in the excavation of an industrial-scale SAF and a pilot-scale SAF in Norway. The presence of the hard build-up zone below one of the electrodes and absence of a slag zone below all three electrodes are unique features of the SAF excavated at Transalloys.

By Grégory Miette

The paper deals with a process that allows the recycling in a cupola of EAF dusts with 18 % Zn. It produces dusts with zinc grade higher than 50 - 55 % and commercial cast iron with less than 200 ppm Zn, 50 ppm Pb, 0.15 % S. The paper focuses mainly on lab tests made with the aim to develop an effective formulation of self reducing - melting pellets. With such a formulation, agglomerates develop a breaking load higher than 125 - 150 kg without any thermal treatment. Zinc and lead are volatilized in the cupola with yields higher than 95 % at 1200 OC, before any melting. Sulphur is transfemed into gas and slag. All these conditions allow to lower zinc, lead and sulphur grades below the cast iron specifications. Results of first bench scale tests performed at Fonderie Piret to validate the process will be presented.

Jan 1, 2002

By A. C. Wadhawan

In the present context of rapid industrialization, production of Lead-Zinc metals from low grade materials, residues and wastes can make substantial contribution to the supply of these metals in India. Recovery from secondary sources also plays an important role in conservation of mineral resources and lower power consumption. Conscious effort is therefore, required to increase the secondary metals which, besides saving in energy cost will also help in waste material management and keeping environment clean. The major thrust is, therefore, needed in this direction. During all these years, the Indian Lead- Zinc industry has made sustained efforts for recovery of metals from low grade ores and from metallurgical wastes and residues. The paper identifies the treatment of low grade ores by various technologies and techniques and the treatment of metallurgical residues and wastes generated during primary Lead and Zinc smelting in India. Some of the major achievements in past decade have also been elaborated in the paper. The strategies to be followed for continuing treatment of low grade ores and waste materials by adopting newer, environmental friendly technologies, in consonance with the rigid standards being adopted by most of the countries including India. have also been dealt with in the paper.

Jan 1, 1994

By José D. T. Capocchi

Viscosity of liquid lead, tin, and Pb-Sn alloys has been measured by the rotational viscometer method in the temperature range from 50 K above their respective liquidus temperature to 823 K. The results are accurate to within ±1.0 %. The variation of viscosity with temperature followed the Arrhenius-type equation µ = µo.exp(Q/RT). The composition dependence of the isothermal viscosity and the activation energy for viscous flow have not shown anomalous changes at the eutectic composition of the Pb-Sn system.

Jan 1, 2000

By Björn Saxen

Outotec atmospheric Direct Leaching has so far been implemented for zinc production capacities of around 100,000 t/a. Lately, there has been growing interest for small scale direct leaching plants, producing circa 30,000 t/a of Zn. Such small leaching plants can provide extra front-end capacity in existing roaster-based plants and enable treatment of feed materials not suitable for roasting. In small scale plants the proven OKTOP® 9000 Direct Leaching reactors are not readily applicable, due the large size. For smaller installations a modular approach is proposed providing multiple advantages, such as reducing the construction time and amount of the site work required causing less disturbance to regular plant operation with reduced cost. In this paper, we present advantages that can be achieved by using modular OKTOP®C reactors and discuss also process design when connecting a small scale direct leaching process to an existing zinc plant. Also benefits of direct leaching expansion are presented.

By Larry M. Southwick

Considerable process and equipment development and analysis were conducted during design of Freeport Sulfur's laterite nickel facilities in the late 1950's. These covered ore concentration at Moa Bay, Cuba, and concentrate refining at Port Nickel, Louisiana. Both facilities utilized acid pressure leaching and product refining steps that were similar to those later used elsewhere in the laterite processing industry. Unfortunately, developments in Cuba removed the Moa Bay facilities from Freeport control. This deprived the project of a start-up that would have allowed thorough resolution of difficulties and a quicker attainment of production capacity. This meant lost opportunity to positively prove and complete the technology when optimum resources and staff were available. This paper reviews the original rationale of how design was developed via laboratory, bench scale and pilot studies by Freeport Sulfur. Some later operating problems will also be discussed. This case is unusual, but the lessons learned may be instructive in the application of difficult and complicated technologies, as well as the need to understand and retain access to the original development and design activities Keywords: Moa Bay, Freeport Sulfur, Port Nickel, acid pressure leaching, pilot plant, pachuca, Chemical Construction, pressure letdown, cobalt, titanium

Jan 1, 2004

By Yu Hu, Gabriella Tranell, Song Zhang, Eivind Johannes Øvrelid

"In the present research, recycling feedstock of silicon for Photovoltic (PV) application is investigated. Whether these recycling feedstocks are reliable in the future use is discussed in this work to assess the properties of the crystal silicon ingot, which is commercially pulled from top-cuts of casted multicrystalline ingot via one kind of Czochralski method - FerroTech. Dopant is the acceptor type Boron (B) and growth direction was <100>. Crystal diameter and the length were 190mm and about 1700mm, which were controlled by the temperature and the pulling speed, then cut to 156mm * 156mm wafers with 2000um and 200um thickness. Resistivity measurements of these wafers by Four Point Probe (FPP) are in good agreement to the calibrated profile after Rapid Thermal Process (RTP). In this work, the Minority Carrier Lifetime MCI, shown by Carrier Density Image (CDI) and Quasi Steady State Photo Conductance (QSSPC), gives the mapping results on the cross section and the relationship to the injection level, increases in an arrange from 40us to 90us along the ingot height, which is abnormal distribution compared to the standard ingot. Then Oxygen and other metal impurities distributions, measured by Flourier Transform Infra - Red (FTIR) respectively, account for the novel phenomenon of the continuously increased MCI. Various types of heat treatments were performed on these wafers (different ingot and different positions) in N 2 and 0 2 mixture atmosphere. Before and after heat treatment, micro-defects were revealed by copper decoration and etching work. Solar cells are fabricated by Energy Research Center of the Netherlands from the experimental ingot, and processed under an industrial standard line. Compared to results of the reference mono-crystalline and multi-crystalline silicon solar cells, the performances of experimental ones show excellent efficiency values up to 18.5%, and Jsc values up to 37mA/cm2.IntroductionThe PV industry has gone through rapid development, with a high growth rate resulting in an increasing demand for silicon feedstock. In addition, costs in production need to be reduced such that solar energy can compete other conventional and renewable energy. Searching low cost, reliable and efficient feedstock is one promoting way to improve and enhance the competitiveness of the PVindustry.More and more researchers start searching new raw materials for PV application [1]-[4]. The key to make full use of low cost raw materials is to control the distribution and effect of impurities, such as Carbon, Nitrogen, and other metal contamination [5]."

Jan 1, 2013

By David M. Davidson

Seven intrusive phases have been mapped to date in the 1 b.y. Red Bluff Granite Complex (RBGC) near El Paso, Texas. This batholith is 20 km2 in area and intrudes older supracrustal units as well as a trachyte ignimbrite cap. Two early microgranite sills are spatially separated 6 km from a porphyritic, three-phase "ring complex" by a tin-bearing, biotite granite which cores the RBGC. These units are intruded, in turn, by a riebeckite granite which locally exhibits lineated and pegmatitic textures as well as exceptionally high light REE and Zr values (800 ppm La; 3,000 ppm Zr). The riebeckite granite is exposed in three separate occurrences within the Franklin Mountains. REE values in the RBGC are depleted in HREE and show distinct negative Eu anomalies. Typical La/Yb ratios are 5:1-2:1 with Eu values ranging from 10-80 ppm. The mineral source of the high REE values in the riebeckite granite has not yet been specifically identified, but is believed to be zircon.

Jan 1, 1988

By Stephen K. Pave1

Over 1,100 tons per day of Fluid Catalytic Cracking Unit (FCCU) catalyst is used worldwide. During the cracking reaction, catalyst is contaminated by deposited metals including nickel, vanadium, potassium, copper, iron, sodium, etc. To compensate for contaminants, a portion of the circulating catalyst inventory is withdrawn for disposal and fresh catalyst is added. The DEMETR process takes spent FCCU catalyst and removes a portion of the metal contaminants, enabling the refiner to recycle demetallized catalyst, thus reducing the solid waste from the refinery. Through August, 1993, the operation of one unit for one refiner has resulted in the recycling of over 7,500 tons of spent catalyst.

Jan 1, 1994

By Ralph H. Nafziger

The Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory, has electroslag melted a V-5Ti-5Cr alloy using a fused CaF2, flux. The alloy is a candidate for use in future fusion reactors. One objective of this research was to evaluate the feasibility of the electroslag melting process in separating simulated radioactive isotopes from the V alloy to demonstrate recyclability. Small amounts of Ca, Y, and Mn were added as surrogates for radioactive isotopes. Results showed that this vanadium alloy can be electroslag melted satisfactorily. The impurities added intentionally were removed or decreased successfully. Among the major alloying constituents, Cr was retained but there were some Ti losses. The latter may be controlled with process refinements. This research suggests that the electroslag melting process could be a suitable method for recycling V alloys after use in future fusion reactors, or for processing other reactive metal alloys with more immediate applications.

Jan 1, 1996

By Philip E. J. Green

Two of the cornerstones of total quality management, the use of statistical and problem solving tools, and the involvement of employees, are directly applicable to environmental protection. The reduction in variation decreases the chances of violations and mishaps. Involving employees in minimizing environmental impacts is critical. One mistake, even with the best technology, and your plant can be shut down, customers lost and fines and penalties imposed - your reputation and the environment damaged. Proven strategies for involving employees in environmental protection, and over-coming the frequently strong differences of opinions about what constitutes environmental protection, will be discussed.

Jan 1, 1992

By A. S. Block-Bolten

Two innovations in nickel-arsenic separation have been studied on a laboratory scale. The first requires only a nitric acid atmospheric leach without preliminary roasting and leads to favorable final conditions for precipitation of arsenic as highly stable FeAsO4, The second is an NaOH-H2O2 pressure leach which is an alternative to the known NaOH-O2 pressure leach. Either method offers the possibility of rapid and efficient separation of nickel from arsenic and is applicable, for example to the high grade niccolite deposits in the Great Slave Lake area of northern Canada.

Jan 1, 1982

By Makoto Ohlsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SME). The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force. The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films. The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a Ni50Mn25Ga25 or Ni52Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace. The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains. After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature. The martensitic transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated. After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found. The constraint-aged films also showed the two-way 3ME by thermal cycling.

Jan 1, 2003

By Makoto Ohtsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SMB), The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force, The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films, The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a NisoMn2sGa25 or Nis2Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace, The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains, After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature, The martcnsitie transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated, After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found, The constraint-aged films also showed the two-way 5MB by thermal cycling,

Jan 1, 2003