Search Documents

By Kezhuan Gu

Data on the kinetics and thermodynamics of dephosphorization are analyzed in terms of the dynamic partition ratio, determined by a combination of slag thermodynamic properties and the balance of oxygen supply and consumption. A recently developed phosphate capacity correlation is combined with data on kinetics to quantify the most significant parameters in controlling the interfacial oxygen potential. The role of slag composition, entrained gas fraction and temperature are discussed in addition to metal carbon and sulfur content. It is demonstrated that the mass transport of oxygen in the slag is enhanced by factors increasing conductivity and inhibited by entrained gas. The mass transfer of phosphorus in the metal is described considering surface renewal induced by CO bubbles.

By N. M. Komkov

The main operation of obtaining zinc from sulfide raw materials by hydrometallurgical technologies is the oxidation roasting of zinc concentrates in fluidized bed furnaces. The technical-economic parameters are determined by the parameters of the roasting process, which depend on the composition of the initial raw materials, the temperature of the bed and on other factors. The predetermined roasting temperature is maintained due to the change of specific efficiency as well as to the quantity of the heat removed from the bed. The efficiency of caissons depends at a high degree on the composition and the thickness of the accretion formed on the surface of the caissons. Forecasting the roasting results is impossible unless we know the mechanism of the accretion formation. The aim of the present paper is the thermodynamic analyses of the behavior of the charge compositions under roasting and the determination of the potential mechanism of the accretion formation. The thermodynamic analyses show that under conditions of the oxidation roasting the thermodynamic probability of the formation of zinc sulfate is higher than the probability of the oxide formation until a temperature of 873°K is reached. The thermodynamic probability of the formation of the lead sulfate is higher than the probability of oxide formation in the entire temperature range of roasting. The probability of formation of ferrites and silicates of zinc decreases only insignificantly the sulfate stability. The results of the investigation of the accretions composition formed under roasting of concentrates with particle sizes less than 0.02 um (60%), containing 65% of sphalerite (ZnS), 12% of pyrite and chalcopyrite (FeS2 and CuFeSz2 each, 3% of galenite (PbS), 7% of silica and other non-ore minerals, have shown that the composition of accretion varies depending on the depth of the accretion layer. The accretions on the caissons and the thermo-siphons consist mostly of zinc sulfate (more than 50%). The accretions of forchamber consist mostly of zinc oxide. They also contain ferrites and silicates. The formation of the sulfate zinc accretion in the cold parts of the fluidized bed furnace (the caissons and thermo-siphons) may be explained by a lower temperature on the surface and probably by a catalytic influence of the present oxides in the formation of S02 and sulfates. The nature of the structure of the accretion in the hotter parts of the furnace may supposedly be explained by the formation of elemental vaporous zinc during roasting.

Jan 1, 2003

By Roy J. M. van Lier

In industrial aqueous solutions, germanium generally occurs in trace amounts amid high concentrations of other metals, such as zinc, copper and iron. Separation of germanium from these metals as well as its isolation from gallium and indium pose a real challenge to the hydrometallurgist. After a brief discussion of the aqueous chemistry of germanium, this paper reviews the flowsheet of the Apex Mine in Utah. The Apex property was the only mine in the world to be operated primarily for production of gallium and germanium, but apparently closed due to great operating difficulties. Several process variants proposed for the treatment of the Apex ore, including bioleaching methods, are addressed. Following a more general description of the behavior of germanium in hydrometallurgical zinc processing streams, available technology for its recovery from aqueous solutions is summarized. Precipitation, solvent extraction, ion exchange, electrowinning, ion flotation and liquid-membrane separation are all outlined in terms of the aqueous chemistry of germanium. Finally, the production of high purity germanium dioxide and metal is briefly discussed

Jan 1, 1995

By Chunyang Guan, Jilai Xue, Jun Zhu, Qiaochu Liu

"Al-Sc Alloys have showed many advanced properties for a wide range of industrial application, which is usually produced using thermal reduction process. This work is aimed to develop an electrochemical process to make Al-Sc alloy using industrial Hall aluminum reduction cells. The experiments have been carried out in a lab cell where NaF/AlF3-Al2O3-LiF as electrolyte, Sc2O3 as raw material, and liquid aluminum as cathode were used at operating temperature of 950 °C. The resulting Al contained 0.2 - 0.5 wt.% Sc that is the common range in its content for advanced applications. However, a small fraction of Sc was found from thermal reduction at Al melts interface. SEM-EDS and ICP-AES analysis showed a uniformed distribution of Sc at varying locations of the Al-Sc alloy sample. In addition, a higher Sc content in Al-Sc alloy can be obtained with introducing ultrasound through the cathode than that without it.IntroductionIn recent years, scandium has been investigated as an alloying element for aluminum alloys. With addition of a small amount of Sc, Al alloys can improve the strength, weld ability, resistance to re-crystallization and corrosion resistance [1-3]. Due to their advanced properties and potential applications, the demand for Al-Sc alloys will increase in the future. However, the difficulties in reduction technologies and the high costs in production process may limit their expansion in application areas.The current major method of producing Al-Sc alloys is to mix Sc into Al by melting Al-Sc master alloy. This alloying process has several technical problems, such as easy segregating and heavy burning loss, etc. The price of Sc metal or starting material is also high, so the mixing process is an expensive alloying method. Molten salt electrolysis is alternative method to prepare RE metal and RE alloys [4, 5]. It also can reduce the segregation of alloying elements. Sc2O3 is an ideal material as raw material with low price and decomposition voltage. Some work has proved that Al-Sc alloys can be obtained by electrolysis Sc2O3 directly in cryolite [6-8], or CaCl2 molten salt [9]."

Jan 1, 2012

By H. Bai, B. G. Thomas

"A three-dimensional finite difference model has been developed to study the liquid steel-argon bubble two-phase turbulent flow in continuous casting tundish nozzles. Experiments have been performed on a 0.4-scale water model to verify the computational model by comparing its prediction with velocity measurements using PIV (Particle Image Velocimetry) technology. The computational model was developed using CFX and then employed to investigate the effects of various casting process variables. A fast, simple inverse model to quantify relationships between those process variables was developed, based on interpolation of the numerical model results, using Bernoulli's Equation and advanced multivariable curve fitting methods. Predictions using this model compare well with plant measurements. The model has been applied to present trends and observations on the relationship between casting speed, tundish depth, slide gate opening, and argon gas injection rate. The results can also be used to predict .the theoretical steel flow rate through the nozzle, so that clogging conditions can be identified in the plant.IntroductionTundish nozzle geometry is one of the few variables that are both very influential on the casting process and relatively inexpensive to change. Designing an effective nozzle requires quantitative knowledge of the relationship between nozzle geometry and other process variables on the influential characteristics of the flow exiting the nozzle. This relationship depends on the flow pattern within the nozzle components. Most previous modeling studies of flow in the nozzle have focused on single-phase flow [1-4]. Argon injection into nozzle is an efficient and widely employed method to reduce nozzle clogging, even though the real working mechanism(s) are still not fully understood [5]. Argon injection may greatly affect the flow pattern in the nozzle, and subsequently in the mold. Therefore, two-phase flow modeling is needed to improve understanding of fluid flow in the nozzle."

Jan 1, 2000

By Hsi-keng Hu

"This paper deals with the flotability of stibnite and summarizes the major experiences and technological innovations of some typical practices of antimony sulfide ores in China. Experiences of cyanide-free and -less flotation of complex antimony sulfide ores and the application of the heavy media process to the preconcentration are described.Performance improvements obtained by innovations in operating techniques are also outlined and discussed. Technical innovations involve: (1) ramification roughing and differential-rate cleaning of stibnite-arsanopyrite ore; (2) the application of the new flotation reagent system; (3) process of separation flotation of Sb-Hg bulk concentrate; (4) extraction of gold from Au-Sb bulk concentrate; (5) flotation recovery of coarse stibnite particles.IntroductionChina is rich in natural resources of antimony and is one of the major antimony producers in the world. During the past several decades, a lot of research works have been done and many experiences in milling practices were gained, some of which are summarized briefly as follows.I. Heavy Media separation of Antimony sulfide Ore at Xikuangshan Hill, Hunan province (1)HMS as a technique of preconcentration of antimony ore has been performed more than ten years in China with good results.1. Ore characteristics The antimony ore of Xikuangshan belongs to the epithermal- metasomatic-filled doposit of antimony sulfide. Major minerals are stibnite (92.1%), antimony oxides (7.9%) and a small amount of pyrite and pyrrhotite; the gangue minerals are quartz, silicic limestone, calcite, hydrous kaolin, sericite, barite and others. The specific gravity of the ore is 2.8 and the specific gravity of stibnite and gangue are 4.6 and 2.654, respectively."

Jan 1, 1988

By R. P. Tavares, M. Isac, R. I. L. Guthrie

"The configuration of the metal delivery system used in twin-roll casting can play a significant role in determining both internal and surface quality of the strips produced by this process.In the present work, a mathematical model for coupled turbulent fluid flow, heat transfer and solidification was developed and used in the study of metal delivery systems for twin-roll casting of low-carbon steels. This study was applied to a pilot twin-roll caster being investigated in Canada, with a roll radius of 0.3 m, producing strips of thicknesses from 4 to 7 mm, at roll speeds ranging between 4 and 12 m/min. Various configurations of metal delivery systems were simulated and their effects on the advance of the interdendritic solidification front and levels of turbulence and temperature within the caster investigated. According to the predictions of the model, an extended nozzle with inlet flow towards the surface of the rolls seems to be the best alternative for feeding liquid steel into twin-roll casters.A full scale water model of a pilot twin-roll caster was also built and used to qualitatively validate the predictions of the mathematical model.Various techniques for fluid flowvisualization were applied. In general, the predictions of the mathematical model were in reasonable agreement with the experiments with the water model."

Jan 1, 1999

By Deventer Johanna van

Ore bodies around the world are declining in grade, whilst increasing in complexity. The level of impurities relative to the valuable metal is steadily increasing, posing new challenges to existing operations. Ion exchange is widely used in the hydrometallurgical industry for both primary recovery of metals and the removal of impurities. The superior selectivity of ion exchange resins makes them exceptionally suitable for the removal of target impurities to very low levels, thereby saving operating costs, increasing the value of the final product and significantly improving revenue. The ion exchange process in these applications is very simple, using standard ion exchange equipment and acid regeneration. The process can be fully automated, requiring minimal operator interference and supervision Examples of impurities that are successfully removed via ion exchange include iron, antimony and bismuth from copper electrolyte. In the copper electrolysis process, antimony, bismuth and arsenic tend to form slimes which are dispersed in the electrolyte. These slimes contaminate the cathode and/or decrease the quality of the copper deposition. A special chelating resin was developed to remove antimony and bismuth, while at the same time ensuring minimal chloride leakage to the sulphate matrix. The work is described in more detail in this paper. Ion exchange is also used to remove copper, zinc and nickel from cobalt electrolyte. This paper addresses a few of these examples in more detail.

By P. D. Lee

The effect of strontium on porosity formation in aluminum-silicon alloys is not well understood and there is no consensus upon the cause of the effects observed. This paper describes a series of experiments where the effect of adding strontium on pore formation was observed directly with combination of a traditional temperature gradient stage and real time micro-focus radiography. These in situ observations provide a new insight into the effect of strontium on the nucleation and growth kinetics of porosity. The addition of strontium was found to have a minor effect on the growth of the pores in the mushy zone. However, strontium appeared to alter the nucleation and stability of hydrogen bubbles within the melt. The interaction of strontium with titanium-boride grain refiners produced an even stronger change in the nucleation and stability of the bubbles formed.

Jan 1, 2002

By R. Boom, B. Kraaijveld, H. Kuntzel, Y. Meteleva-Fischer

"Alloying refining with rare earth elements followed by acid leaching was examined for the potential of upgrading of metallurgical grade silicon. Microstructure study of silicon alloyed with small additions of rare earths showed behavior relatively similar to the influence of calcium addition. After alloying with neodymium the phosphorus content was detected in various intermetallic silicides containing neodymium and iron. The content of lanthanum and neodymium in refined silicon was by several times lower than that of aluminium and calcium. Alloying with lanthanum and neodymium at smaller additions than calcium reduced the phosphorus content down to the same level. The efficiency of lanthanum and neodymium in removal of boron and phosphorus at the 1-2 wt% of their additions and their low solubility in silicon make the alloying with these metals followed by acid leaching an attractive option for the refining route of metallurgical grade silicon up to solar grade.IntroductionA striving for a cheap ""green"" energy directs the research interests in silicon solar cells towards new efficient refining routes for metallurgical grade silicon (MG-Si, -98% purity). The silicon price determines up to high extent the solar module's price, so that cheap and efficient metallurgical process is awaited. The research challenge is to fulfil the purity requirements of solar grade silicon (SoG-Si, 6N) by competing with the energy-consuming and environmentally unfriendly Siemens process. Most difficult impurities to remove are boron and phosphorus, so technologies dedicated to their efficient removal attract an attention of industry and academia.Alloying refining (also known as solvent refining) is one of the most promising refining options, which is based on a principle of solid-liquid extraction using limited solubility of impurity elements in solid silicon [ 1]. Various elements were proposed for alloying refining: aluminium [2], calcium [3], tin [4], iron [5], copper [6] etc. The attractiveness of the alloying refining is in decreasing a melting point of the metal mixture and an affinity of the alloying element to the most harmful impurities, especially to boron and phosphorus. However, the difficulties are still faced due to self-solubility of the alloying elements, their low affinity to boron and/or phosphorus, silicon losses and necessity of removal of the silicide impurity phases in an additional step, using acid leaching [7], fractional melting [ 8] etc."

Jan 1, 2013

By C. Ramasamy

The tariff reductions on imports, as a part of on-going liberalisation process in India, has fueled competition within and outside India and has, in turn provided an opportunity to reach global markets. This change calls for quality upgrades and cost-competitiveness without impairing the environment. In this context, gas based processes, contributing to improvement in quality and environment as well as processes where controls are applied when gases inimical to environment are involved, are discussed in a remelt/cast-house scenario. The impact of such processes on fabrication cost of sheet ingot is seen alongwith consumption and cost of materials and compared with a world class standard plant in North America.

Jan 1, 1996

By Helena Byrdziak

Polish Copper Industry, located in the Lepica-Glogów region and operated since the 1970's, includes four mines and two smelters, "Legnica" and "Glogów", the latter consisting of "Glogów" I" and "Glogów II" both having different technologies. The "Legnica" and the "Glogów I" smelters using shaft furnaces, so sulfur elimination largely takes place during batchwise converting, resulting in fluctuation SO2-concentration between less than 1% up to 10% in the converter pas W the sulfuric acid plants. The ensuing difficulties of the past have now largely been overcome. Introduction of flash smelting at "Glogów II" with subsequent acid making by double SO2-conversion from the stable process gas, contributed significantly to further reduction Of SO2-emission. In 1994 a new double conversion sulfuric acid plant was installed at "Glogów l" as well as a "Solinox" desulfurisation plant at "Legnica", further reducing SO2 emission considerably, The next step towards this goal under consideration is a semi-dry desulfurization system for the "Glogów I" power station, SO2- abatement measures by KGHM and the results thereby achieved are presented.

Jan 1, 1996

By Klas G. Hultbom

Mercury is present as trace contaminant in many raw materials for metallurgical plants. When such materials are treated with pyrometallurgical processes the mercury is volatilised. Mercury has a high vapour pressure, even at low temperatures, and therefore it is removed only partly by normal gas cleaning processes. The Boliden Norzink scrubbing process removes elemental mercury by converting it to calomel. It is widely used in the base metals industry. This paper gives examples of the application, and also outlines the background for the development of the process. Another technology developed by Boliden for mercury removal is the Selenium filter. This is a fixed bed filter based on the reaction between elemental gaseous mercury and selenium, by which mercury selenide, HgSe, is formed. The mercury selenide is a highly stable compound with extremely low solubility in water and very low vapour pressure. Mercury is removed selectively without any side reactions. Special applications for the selenium filter technology include mercury removal from gases containing sulphur dioxide and geothermal off-gases.

Jan 1, 2003

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By A. L. Paverd

The petrology of a number of pyrometasomatic mineral deposits in north Queensland, Australia, were studied to evaluate the use of mineralogy and major element chemistry in the exploration for copper, lead and zinc-bearing skarns. Results indicate a direct correlation between the character of the mineralization and the composition and nature of the host rock. The study of garnet compositions proved the most useful. Economic mineralization was limited to limestone-derived skarns containing garnet of And60-90, whereas skarns containing garnet of less than contained less than 1And55 contained less than 1% total sulfide. Skarns containing garnet of And60-8S host the best mineralization; above And8S' copper, lead and zinc sulfides decrease and magnetite and pyrrhotite become the dominant ore minerals. Similar correlations were found for pyroxene, amphibole and 'the bulk composition of the skarns.

Jan 1, 1981

By Milton Blander

A review of concepts and theories for predicting thermodynamic solution properties of multi- component high temperature liquid solutions is reviewed. During the last 50 years the ability to predict :such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.

Jan 1, 1996

By J. -P. Nepper

It has been possible to largely contain converter aisle emissions of SO2 and fumes in the case of batch-wise operated Peirce Smith converters during normal blowing periods with the help of suitably designed primary hoods. Controlling the escape of off-gas during the periods of turning the converter in or out of the stack has been problematic in the past. Effective automated contro1 systems have been deve1oped for the purpose and successfully applied in smelter operations in Spain, Taiwan and Germany. This has led not only to an effective reduction of emissions in the converter environment but also to an improvement in the converter operation.

Jan 1, 1992

By Colin Dessemond

Since 1950, the traditional process has been dominating the production of lithium compounds from spodumene ores to sustain the lithium market because of its economic viability and the markets need for technical grade (99.5% purity) product. This traditional process includes thermal conversion, acid roasting and lithium leaching. However, this process has not been challenged and very few studies have tried to explain its limitation (95% lithium yield) or optimize the thermal treatment. Here, α to β spodumene conversion and lithium extraction were performed in a rotary kiln on a 2 mm to 2 cm spodumene concentrate instead of a micrometric one using a 1050 °C, 30 min conversion treatment and 250 °C, 30 min, 30% H2SO4 excess leaching treatment. X-Ray Diffraction analyses were performed on the converted material to determine the conversion rate by Rietveld analysis. It was observed after thermal treatment that the α-spodumene particles fractured and divided while the impurities remained compact. A sifting was performed after thermal treatment and it was determined that 65% of the initial mass became finer than 180 μm. X-Ray diffraction analyses and lithium content measurement were performed on both fractions and it was determined that the finer fraction had a very high lithium content of 3.24 wt%. Lithium extractions were performed on both fractions separately. While the coarser fraction’s lithium yield was only 61% the finer fraction’s lithium yield went up to 99% without any additional treatment. These observations may open more economical ways for the traditional process by potentially bypassing two third of costly steps such as grinding.

By T. T. Chen

Raw anode slimes consisting primarily of PbSO4, AgCuSe, Cu3Se2, Cu2-x Se, Cu2O, CuSO4.5H2O, Sn arsenate and Sb-Bi-As oxide are batch-leached with electrolyte-O2 to dissolve Cu. During this process, Cu2O and CuSO4.5H2O are solubilized and the Cu in the selenides is leached with the formation of Ag2Se and Se. A small amount of Cu remains in the Ag2Se, Sn arsenate and Sb-Bi-As oxide. The decopperized slimes are repulped in Na2CO3 solution to convert most of the PbSO4 to NaPb2(CO3)2(OH). The Sn arsenate and Sb-Bi-As oxide partly react, but the Ag2Se is not significantly affected by the Na2CO3 solution. The NaPb2(CO3)2(OH) intermediate phase is dissolved in acetic acid to leave a final product consisting of Ag2Se, Se, Sn arsenate and Sb-Bi-As oxide, together with small amounts of PbSO4, NaPb2(CO3)2(OH) and various gangue constituents.

Jan 1, 1993

By Duan Xin-hui, Wang Xin, Peng Jin-hui, C. Srinivasakannan, Zhang Li-bo

The work attempts to optimize the process of preparation of modified semi-coke from semi-coke using phosphoric acid (H3P04) as the activating agent using the response surface methodology (RSM). The influences of three major dependent variables, the impregnation ratio, activation time, and activation temperature were assessed on the independent variables yield and the iodine number. The empirical relationship between the dependent and the independent variables were established using the quadratic response surface models, which were utilized to optimize the process parameters. The significance of each of the parameters and interaction among the parameters on the independent variable was assessed based on analysis of variance (ANOVA). The process variables were varied within the range of impregnation ratio (IR) from 1.5 to 4, activation time from 30 to 90 min and activation temperature from 550 'C to 650 'C. The optimized process conditions were estimated to be an IR of 2.29, activation time of 32 min, and an activation temperature of 605°C respectively using the process optimization tool. The BET surface area of modified semi-coke of the optimized sample was estimated to be 915m2/g, with the pore volume of0.71cm3/g, with an average pore diameter of 3.09 nm, with micropore volume fraction being 52.36%. The scanning electron microscope (SEM) images were utilized to visualize the surface pore structure.

Jan 1, 2013