Search Documents

By C. L. Karr, D. E. Goldberg

This paper considers optimization of the design and operation of an air-injected hydrocyclone (AIHC) via a genetic algorithm (CAI. The AIHC is a mineral separating device, developed by the U.S. Bureau of Mines, that combines the selectivity of flotation with the capacity and simplicity of hydrocyclones. GA's are search procedures based on the mechanics of natural genetics. Computer results demonstrate the ability of a GA to rapidly locate design and operating parameters that improve AIHC performance. A computer model of the GA-designed AIHC predicts improved recovery over that currently being obtained with an AIHC in operation at the U.S. Bureau of Mines Tuscaloosa Research Center.

Jan 1, 1990

By Edgardo I. Cifuentes, Andrew L. Mular, Andrew Burkert

Experimental designs are data acquisition plans which, if followed exactly, will quickly provide process engineers with information to assess statistically the individual and joint influence of factors on responses to permit of rapid decision making. Methodology employed to construct data acquisition plans is described in some detail. In production environments, factorial designs are appropriate for most purposes. Use of two level factorials to make decisions is described for a grinding circuit.

Jan 1, 1991

By J. A. Frew, G. I. Orrock, R. M. Glen

The zinc flotation circuit was sampled to provide sized information on its metallurgical performance. A good balance was obtained and the roughing, scavenging, cleaning and regrind sections were assessed. Substantial losses of sphalerite occurred in all sizes. The limitations were poor recovery in the cleaning section which resulted in substantial recycling of 15-30µm sphalerite and iron sulphides, and inability to float +38µm sphalerite in the roughers. Regrinding increased sphalerite recovery by 7% with no loss in grade. Liberation measurements enabled balances for six size fractions to be calculated and the role of liberation on the metallurgical performance was assessed.

Jan 1, 1993

By A. K. Haines, M. W. Godfrey, D. M. Miller, P. C. van Aswegen

The Bacterial Oxidation [(BIOX)] process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairvew Mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developmenst to improve plant operating efficiencies. These new developments, which include a higher solids content of the pulp feed to [BIOX], lower retention times, higher operating temperatures, lower power utilizaton for oxygen dispersion and reduced nutrient addition, have all been successfully implemented on the Fairvew plant. It has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Contineous cyanidation pilot plant work conducted on [BIOX] product has indicated that cyanide consumption can be drastically decreased if a continuons flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1992

By Jorgen Elbrond

The mineral industry shares a particularity- heterogeneity-with the other primary industries exploiting nature such as agriculture, fisheries, and forestry, which may not be found in the secondary industries, In the mineral industry heterogeneity is evident both in the raw material, the ore in situ, and in the working conditions. Mining engineering, which encompasses the tools for designing mine production systems, is mostly an assembly of the other branches of engineering and applied science. The assemblage's goal is to arrive at an optimal production system. As such, mining engineering is similar to systems engineering. The technique for the development of systems-mine production systems or mining operations -is operations research with its succession of activities: observations, modeling, experimentation, and verification. Comparisons among alternative systems are highly desirable during the development phase of a mining operation as well as during later phases where modifications, ameliorations, and expansions are carried out on the existing system. The role of the independent consultant in systems design and development lies in the collection and breadth of experiences from modeling and model verification in other operations, which he can add to a new system's development and thus in- crease its credibility with management.

Jan 1, 1979

By D. Royston

Curved pulp lifters can provide improved discharge performance from SAG mills, especially for the coarser fraction of rocks in the discharge. They also can provide improved wear life of the pulp lifter, especially the base of the pulp lifter and diversion cone, over comparable straight radial pulp lifters. Current experience with curved pulp lifters and associated grates is covered including design issues and discharge performance for both the slurry and rock components of the discharge.

Jan 1, 2003

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By Gordon R. Wicker, Peter V. Avotins, Steven S. Ahlschlager

Laterite ore slurries exhibit Bingham plastic behavior and can be characterized by the magnitude of their yield point and Bingham viscosity. These two parameters are affected by ore composition, solids concentration, and temperature and are used to predict the pressure drop in pipelines and heat transfer coefficients in shell-and-tube heat exchangers. In cycloning of laterite slurries, the calculated cut size is corrected by factors obtained from the rheological parameters.

Jan 1, 1979

By Kotaro Ohga, Kiyoshi Higuchi, Zhang Xun Tao

In Japanese coal mines, drivage works of in-seam gate roads are mainly carried out by blasting methods. Changes of methane concentration in gate roads are recorded by centralized monitoring systems in general. To obtain useful information from the recorded data, authors analyzed changes of methane concentration for 3 hours after blastings. As a result, the changes of methane concentration with time can be divided into five distinct patterns. It is thought that appearance of the each pattern depends upon the geological conditions of the surrounding of the headings. Therefore, we attempted to confirm such observations by simulations using mathematical models.

Jan 1, 1989

By Bruce B. Redpath

Single-charge cratering tests can provide a direct measure of the powder factor necessary for achieving a desired effect in conventional blasting. If a desired blast effect, such as fragmentation or mound velocity, is produced by a single point-charge at a particular scaled depth of burial, then the cube of the reciprocal of that scaled depth is the appropriate powder factor for duplicating the effect in a conventional array of blast holes. Scaling formulas are presented that provide a link between point-, line- and plane-charge geometries, and which can be Apparent crater used for blast design. Mound and burden velocities from several sources are compared and several examples of blast design are given.

Jan 1, 1977

By Donald Lau, Adrian Crawford

In the field of grouting, practitioners fre¬quently advocate procedures that are often unique and contradictory. As a result there has been considerable debate as to what constitutes optimum grouting practice. A knowledge of both the rheological properties and the flow characteristics of grouts is essential to the development of a rational understanding of the grouting process. Flow models and viscosity experiments have been conducted using cement grouts comprising High Early Strength Portland and Microfine cements. The addition of superplasticizers was found to enhance the flowability of the grouts as well as to reduce the effective groutability ratio. Steady state flow equations and design charts for predicting the radial penetration of cement grouts have been developed.

Jan 1, 1986

By K. R. Price, M. Gauna

Jim Walter Resources No. 4 mine produces coal through retreat longwall mining at 610 to 670 m (2000 to 2200 ft) of depth. A three entry, total yield pillar, longwall development experimental region was established for three adjacent longwall panels utilizing 6.1 m (20 ft) wide gate section pillars. Presently, the first longwall panel is completed with roadway deformational behavior monitored for a ground control assessment of the mining system. Data illustrate that the total yield pillar gate section design at No. 4 mine is presently comparable to gate section designs having large equal size chain pillars. Ground conditions will continue to be monitored during the mining of subsequent longwall panels in order to determine the ground control implications from multiple panel extraction.

Jan 1, 1986

By A. D. Unsted

The Premier mine has been in existence for over 75 years and is closely woven into the glamour of the history of South Africa. A note on the geological formation of the diamond pipe and the gabbro gives a clearer overall picture of the mine. Mining methods for operations above and below the gabbro sill are briefly discussed. Ventilation arrangements for mining above the sill are briefly described and possible ventilation arrangements for mining below the sill are discussed in more detail. Note: conversions to S.I. units are not exact as rounding has been done.

Jan 1, 1980

By J. Mark Richardson

Modern mining operations are increasingly affected by complex economic factors. Broad and rapid fluctuations in metal prices, rising operating costs, socio-political trends and the inherent technical difficulties encountered in most operations, all can combine to quickly change once-profitable ventures into money-losing propositions. Accurate knowledge of metal inventories during all phases of an operation has become essential to wise management decision-making. This paper reviews key elements of metallurgical accounting: sampling theory, measurement technology and computerized data adjustment. Application of current technology to the reconciliation of a hypothetical operation is discussed.

Jan 1, 1991

By D. M. Richards, A. D. MacPhail

Highland Valley Copper currently mines two low-grade ore bodies, Lornex and Valley. The partnership was formed in 1986. As a cost reduction measure, it was decided to use an in-pit crushing and conveying system to deliver the ore from the Valley Pit to the Lornex mill 3 km (1.8 miles) away and 175 m (575 ft) above the pit rim. The system uses two gyratory crushers that feed a series of conveyors to transport up to 130 kt/d (143,000 stpd) to the main stockpiles. This paper describes the performance of the in-pit crushing system as it is currently configured, as well as its evolution to date and future planned moves.

Jan 1, 1995

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By E. Topuz, M. J. McPherson, I. M. Konduri

This paper describes experiments conducted to evaluate the effectiveness of jet fans for ventilating blind headings in under- ground mines. A laboratory model of a mine heading was built by using dynamic similarity criteria, and water as the fluid medium. In order to verify laboratory test results, field experiments were designed and carried out in a full scale mine model and in a coal mine in West Virginia. Using CO, as the tracer gas and in combination with a computerized gas monitoring system, tests were conducted to evaluate jet fan performance. The results highlight the flexibility and versatility of jet fans for ventilating blind headings. Numerical modeling of a jet fan in a typical coal mine heading was carried out to evaluate the potential of computational fluid dynamics.

Jan 1, 1997

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By R. S. Das, A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in terms of complexity and value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer-based predictions and practical results. Research conducted to compare computer results with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only if reliable input data are provided.

Jan 1, 1987

By D. B. Stephens

Assessing the occurrence of natural ground-water recharge at mine and mill waste disposal sites may be crucial to addressing regulatory agency concerns regarding the potential impact of waste seepage on ground-water resources. Recharge has been shown to occur even in semi-arid areas where annual lake evaporation exceeds precipitation. Permanent storage of waste seepage in the unsaturated zone is not to be expected if recharge occurs under natural conditions. Establishing the direction and rate of fluid movement in the vadose zone by field measurements is an important element that should be included in the site selection process.

Jan 1, 1987