Search Documents

By Earle J. Klohn

INTRODUCTION The paper presents a broad overview of the geotechnical site studies required for siting uranium tailings dams. These studies, which are interdisciplinary in nature, touch upon such related fields as: hydrogeology, hydrology, and seismicity. Tailings dams are commonly used to develop tailings ponds for the storage of the waste products generated by mine milling operations. In the past, most tailings ponds have been developed either above ground on dry land, or in existing lakes. In the United States a majority of the uranium mines are located in arid or semi-arid regions and past practice has been to store the wastes above ground on dry land (1,2). Currently, the United States Nuclear Regulatory Commission (N.R.C.) recommends below ground disposal of uranium waste products, although they indicate that they will consider above ground alternatives (3). In Canada many of the existing uranium mines are located in a wet environment and past practice has been to use small lakes and depressions as tailings ponds (1,4). However, current practice in Canada leans towards above ground, dry-land storage (5,6,7), and the Atomic Energy Control Board (AECB) guidelines (5) indicate this to be the preferable method. In B.C., where a moratorium on uranium mining has been declared by the Provincial Government, there are no existing uranium tailings ponds. However, both the formerly proposed Birch Island and Blizzard uranium developments would have used dry land storage. Most of the existing non-uranium mill wastes in B.C. are stored behind tailings dams on dry land. The waste products delivered to the tailings pond comprise, the ground-up rock that remains after most of the uranium values have been removed and the excess chemicals used in the milling process. These waste products, which are called "tailings", are normally mixed with water to produce a slurry and then pumped to the tailings pond. Since the uranium recovered constitutes only a small percentage of the ore (usually less than 1%) (8), large quantities of waste rock and associated transportation water are discharged into the tailings impoundment area. Consequently, relatively large tailings pond areas are required for the uranium tailings. In recent years, major advances have been made in the design, construction, and operation of non-uranium tailings storage facilities (9,10,11,12,13,14, 15). These improvements have been based on combining the latest advances

Jan 1, 1980

By K. Kavouridis

Coal is broadly recognized as sure, competitive, diversified, not vulnerable and predictable in price energy resource. In power generation coal is playing a dominant role in the EU-27 with 25% of installed capacity and almost one third of the power generation. The role played by the domestic resources and especially by coal are increasingly becoming the focus of the EU energy strategy. There is a strong pressure for the decarbonization of the energy mix. The Emission Trading system (ETs) can have an impact on the shift to lower carbon-intensity fuels. The impact of ETs on coal can be important, because it is very short sighted and only defines the period up to 2008-2012. The ETs CO2 regime must ensure that investment in coal-fired plants in the long term are supported. EU Research Institutes and Coal Industry identified an important CO2 reduction potential by improving the efficiency of the conversion of solid fuels into electricity. Highly efficient clean coal technologies can contribute to reasonable costs and challenge the issue of climate change. It must be pointed out that the EU Energy policy should now concentrate on the necessity to effectively support demonstration projects and to create the legal framework for the integrated approach of efficiency enhancement and CCS. It is not a right approach to implement CCS before the technology is demonstrated and before it is clear that it will be commercially viable.

Jan 1, 2007

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By John A. Haggman

Philippines is a country that is richly endowed in mineral wealth. In 1988, Climax Arimco Mining Corp. (CAMC) geologists found the Dinkidi porphyry gold-copper deposit in Nueva Vizcaya province. It is the most significant mineral discovery in that country in recent times. To date, the company has defined indicated resources of 124 Mt (136 million st) of 1-g/t (0.029-oz/st) gold and 0.4% copper. This includes a high-grade core of 7.9 Mt (8.7 million st) of 6-g/t (0.175-oz/st) gold equivalent. Total contained metal is 124.4 t (4 million oz) of gold and 499 kt (1.1 billion lb) of copper. Dinkidi's discovery resulted from initial geologic reconnaissance and recognition of the intrusive complex that is exposed at surface and anomalous in its topographic expression. This was followed by systematic exploration. This includes extensive gradient array induced polarization (IP), ground magnetics, geochemical sampling and diamond drilling. This later defined a further 16 satellite porphyry targets in the Didipio region. Climax was been granted a Financial and Technical Assistance Agreement contract with the Philippine government. It allows 100% foreign ownership of mining projects. After four years of negotiations, Climax was the first company to have such an application granted. Some 120 applications from numerous international mining companies are waiting for approval following implementation of new Philippine Mining Act of 1995. Exploration history Didipio is located 200 km (125 miles) north of Manila at an elevation of about 700 m (2,300 ft) in the remote Sierra Madre mountains. This region remains mostly unexplored. The property is accessed by 25 km (15 miles) of logging track from the town of Cabarroguis, Quirino. The area experiences an average rainfall of about 3,000 mm (118 in.) a year. Most of it falls during the July-to-November typhoon season. Didipio was first recognized as a gold province in the 1970s when native Ifugao and Ilongot hunters discovered alluvial gold in the region. The region had been prospected over the years by local companies. They were mostly prospecting for alluvial gold. However, in 1988, Climax Mining geologists identified the potential of an obscure razorback ridge protruding from the alluvial valley floor. This ridge, later named Dinkidi by Climax, was the site of several small- scale tunnels. Locals had mined narrow quartz stockwork veining and sluiced soft argillic alteration zones, using irrigation canals and sluice boxes to catch free gold.

Jan 1, 1997

By Ian P. G. Hutchison

12.1 INTRODUCTION This chapter deals with the tools required to design leach operations to minimize spillage from leach pads and ponds and erosion damage during flood events or prolonged wet periods. It outlines methods used to design for prolonged dry periods when water shortage can be a problem. Seasonal operational aspects such as winter shutdown and coping with spring snowmelt periods are also discussed. General criteria useful when designing pregnant and barren solution ponds are also outlined. The aim of these notes is to provide designers and operators with a simp1ified approach to developing design parameters which make effective surface water management easy to achieve without resorting to extensive or elaborate analyses. Section 12.2 briefly outlines the types of problems associated with wet climates and floods, as well as dry periods. Determination of flood design parameters is discussed in Section 12.3. Circuit water balance and pond sizing are outlined in Section 12.4. Pond design considerations are included in Section 12.5. Worked examples are included in Section 12.6. 12.2 RAINFALL/RUNOFF PROCESSES There are two types of rainfall-runoff processes that are important when designing heap leach facilities. The first of- these is the short-term, intense rainfall or snowmelt events that occur over a period of a few minutes or hours, causing flooding that can lead to erosion damage and overtopping of ponds and containment dikes. Specific problems that can manifest themselves during these events include: • Washout of access roads; • Damage to containment dikes; • Flood water contamination of circuit water; • Damage to process water ponds by perimeter erosion or overtopping and erosion; • Loss of process circuit fluid due to breaks in containment dikes or process water ponds; and • Erosion of leach pile and consequent sediment contamination of process fluid. Other types of rainfall -runoff processes that could cause problems are the long-term-(generally months-long) wet or dry periods. Extended wet periods

Jan 1, 1988

By Frank A. Aplan, Barbara J. Arnold

INTRODUCTION Coal flotation is a fine cleaning process usually present in all but the older preparation plants. It is typically used to clean either the -28 mesh (-500 pm) or - 100 mesh (- 150 pm) raw coal fines, and it is the only commonly used preparation method that can effectively recover coal particles finer than, say, -200 mesh (74 pm). To place coal flotation into its proper context, it should be noted that the bulk of the raw coal sent to preparation plants is treated by gravity concentration. On a worldwide basis, from 0 to 40% of the raw feed to a preparation plant is treated by flotation, while in the US only about 10% of the raw coal feed is floated. Roughly, 50% of US preparation plants use flotation to process at least a portion of the raw coal feed, although most of the newer plants incorporate flotation into their flowsheet. Historically, the process has only been used to treat the raw coal fines naturally occurring after mining and a minimal amount of crushing at the preparation plant. This is in sharp contrast to ore flotation where, typically, the entire tonnage is first ground and then floated. As a consequence, of the approximately 500 Mt of raw coal treated by preparation in the US yearly, it is estimated that only about 40 Mt are sent to the flotation circuits (producing -30 Mt of clean product).'O1 This small tonnage compares with about 400 Mt of ores treated annually in the US by flotation. By analogy to ore flotation, where it is an effective, large tonnage, low cost, easy to operate process, its potential in coal preparation should be great. Reasons why it has not achieved a greater potential in coal preparation have been attributed by Aplan 102 to: 1. Indifferent results in removing sulfur and ash. 2. Difficulty in floating low rank and oxidized coals. 3. Inability to make clean separations with the finer sizes. 4.Inability to clean slurries with a high percentage of clay. 5. Problems with water chemistry. 6. Competition with effective, gravity coarse-cleaning methods. 7. Low value of coal historically. 8. Dewatering problems. 9. Transportation and storage problems with coal fines. 10. Marketing problems with coal fines. 11. Inadequate attention to the process in the plant. 12. Inefficient use of capital and operating monies. Inadequate attention to procedures, machines, and processes.

Jan 1, 1991

By A. Wahab Khair

There are a number of factors, including mine geometry, local geology, geotechnical properties of overburden materials, surface topography, sequence of overburden strata, and extraction rate, affecting characteristics of surface subsidence imposed by large underground excavation. Among the factors, the first three have the major impact on magnitude and area of influence of final subsidence. Hence, a model has been developed, considering mine geometry and geologic and geotechnical properties of the associated area, to predict maximum possible subsidence and subsidence profile at any cross-section within the subsidence influence zone. Based on extensive field measurements and mechanics of strata behavior, under the action of overburden pressure in the vicinity of the large underground excavation, the vertical plane of influence zone has been divided into five areas: 1) excavated, 2) caved, 3) fractured, 4) highly deformed but continuous, and 5) subsided zones. In the final state of subsidence each area maintains a certain volume expansion/contraction, i.e. a factor which depends on geologic, geotechnical properties of overburden strata and state of stress within the subsidence trough. The cumulative volume expansion and contraction partially compensates for the extracted volume and the difference between the two is reflected as the subsided area in the form of the area within a curve defined by a probability function. The input parameters for the model are mine geometry (i.e. length and width of the panel), depth of cover, and geologic and geotechnical properties of overburden strata (i.e. percentage of hardrock, sandstone and limestone, and soft rock, shale within the overburden strata and Rock Quality Designation). The model calculates angle of draw for the site, expansion factor for each zone utilizing empirical relationships, maximum possible subsidence and plots the subsidence profile curve. The model is developed for a longwall excavation with unique characteristics of prediction of angle of draw and maximum possible subsidence for a given geologic and mining condition at any cross-section within the influence zone of subsidence.

Jan 1, 1986

By Daniel W. H. Su

The ability to predict the effects of longwall mining on topography and surface structures is important for any coal company in making permit applications and anticipating potential mining problems. The sophisticated finite element model described and evaluated in this paper is based upon five years of underground and surface observations and evolutionary development of modeling techniques and attributes. The model provides a very powerful tool to address subsidence and other ground control questions. The model can be used to calculate post-mining stress and strain conditions at any horizon between the mine and the ground surface. This holds the promise of assisting in the prediction of mining-related hydrological effects.

Jan 1, 1986

By Tim Cleary, Steve Skelhorn

The 9th Line / 16th Ave tunnels are part of a $700 million expansion of the York Durham Sewage System, north of Toronto. The 15 km of tunnels presented many challenges, including glacial and postglacial deposits, at depths up to 55 m. Due to high hydrostatic heads, the Owner specified EPB tunnelling, however, an alternate was proposed utilising rib and lagging tunnels, combined with a de-watering scheme. State of the art technology was utilised with a new Lovat TBM, incorporating PLC control, soft start water-cooled motors and a head designed to tackle the mixed ground expected. The 9th Line tunnels were completed in 2002. Subsequently the second section of tunnel along 16th Avenue has been awarded to the Joint Venture. This paper presents a case history of the soft ground tunnelling, including design elements, tunnel systems and TBM operations.

Jan 1, 2003

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By Ian Graham

In 2013 the Government of New Zealand launched a number of ‘National Science Challenges’ (NSC) to address major issues facing the nation, and raise public consciousness about science and its role in promoting evidence-based decision making. One of the 10 proposed NSCs focuses on New Zealand’s extensive Exclusive Economic Zone (EEZ) and Extended Continental Shelf (ECS)1, with an objective to enhance utilisation of marine resources within environmental and biological constraints, and the desired outcome of:

Sep 1, 2014

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel's set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By Michael A. Linkous, Mark J. Zdunczyk

Silica in the form of sand and sandstone is one of the most common, and at the same time, unique industrial minerals. Found in every rock type of every geologic age and virtually everywhere in the world, silica is used in products that touch just about every aspect of daily life. Imagine a world in the 1990s without computer chips, fiber optics, or glass, and you have just begun to understand how important silica is to the quality of life we enjoy. The elements silicon (Si) and oxygen (0) comprise roughly 60% of the earth's lithosphere to a depth of about 16 km. The crystal structure of silicon dioxide consists of one atom of silicon bonded to four surrounding atoms of oxygen to form a three-dimensional network of SiO, tetrahedra. This network makes up the mineral quartz (Murphy and Henderson, 1983), the most common detrital mineral in most sandstones. Quartz is also a major constituent of many igneous and metamorphic rocks and is widespread as a siliceous cementing agent in various rock types. Although quartz is common, sandstones, quartzites, and pegmatites and the unconsolidated sediments derived from them that have a silica content high enough and pure enough to meet today's market demands for quality and consistency are not common. USES AND SPECIFICATIONS Silica sand that is mined and processed for industrial uses must conform to the chemical and physical specifications set by customers. In the United States almost half of the silica sand produced is used in the manufacture of glass. Other important products include foundry sand, ground silica, blasting sand, and fracturing sand. Glass Sand Silica is the principal glass-forming oxide in a glass batch. Glass manufacturers develop model specifications for each source of silica sand used. These specifications broadly define the limits and ranges for chemical and physical properties of the sand and are used by the manufacturer in calculating the desired batch mix or formula. Some specifications may be critical to a glassmaker and require very stringent limits on the quantity of impurities in the sand. For example, the total iron oxide content of a batch is extremely crucial when making white or flint glasses (Mills, 1983). Iron is present in almost every raw material used in a glass batch and must be carefully controlled in order to obtain a consistent color in the finished product. It is difficult, however, for a raw material supplier to tightly control the chemistry of a naturally occurring material such as silica sand. To a great extent the commercial quality of a sand is determined by its geologic history. Realizing this, glass producers tailor their model specifications to each source of approved material. In general, a glass company is concerned most about the consistency of raw materials on a day-to-day basis. Soda-lime-silica glass was the earliest type of manmade glass (Baker-Can, 1967) and still accounts for most of the glass manufactured for commercial use today (Mills, 1983). It is relatively easy to melt and shape and is less expensive per ton to produce than most other types of glass (Baker-Can, 1967). Soda-lime-silica glass is used in fabricating containers, flat glass products, incandescent and fluorescent lamps, glass fiber, and many other products. Heavy minerals such as ilmenite, leucoxene, kyanite, and zircon are impurities on which strict limits are placed for a glass batch. Because of their refractory nature they either do not melt or only partially melt, which results in stones or feathers in finished glass. Aluminosilicates such as kyanite also contribute unwanted alumina to the batch as they partially melt. Limits are especially rigid for refractory mineral grains coarser than 0.60 to 0.425 mm (30 to 40 mesh). [Tables 1 and 2] present typical specifications for silica sand used in flat glass and container glass products. The percentages shown represent an average of many companies7 specifications.

Jan 1, 1994

By Z. Yu

Dewatering of a -0.5 mm fine coal has been studied extensively. Deep cleaning requires however fine grinding, and dewatering of such ultrafine products presents a great challenge. Several coal samples finely ground and characterized by different wettabilities have b.een used in the filtration tests. Vacuum and press filters have been employed. In this paper only the results obtained with different flocculants (totally hydrophobic. semi-hydrophobic and hydrophilic polymers) are included. The results reveal the effect of coal surface properties and flocculant type on filtration of ultrafine coal.

Jan 1, 1994

By R. B. Hoy, Stanley J. LeFond, Unni H. Rowell, K. Reckling, Derek G. Fullerton

In 1989 natural industrial diamonds counted for 55% of the world's natural diamond production. Australia is currently the leading producer (35%). Zaire is the second largest producer (19%). of what is primarily industrial grade rather than gem grade. Botswana (17%) is third, with the former USSR (15%) fourth, and the Republic of South Africa (8%) fifth. Diamonds are also mined in Angola, Namibia, the Ivory Coast, the Central African Republic, Ghana, Tanzania, Guinea, and other African countries. In the Western Hemisphere, Brazil is the principal producer, with some production from Venezuela and Guyana [(Fig. 1)]. A very small output of diamonds is mined today in India, which was the first source of commercial production. In the United States, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a pipe there in 1906. Small scale trial mining has not, however, proved economical. Since diamonds were first discovered more than 2,000 years ago, only about 380 t have been mined. In order to obtain 1 g (5 metric carats) of diamonds, it is necessary to remove and process approximately 25 t of rock. Recovering this small percentage involves a combination of highly developed techniques in mining and extremely sophisticated processes in diamond recovery. END USES Diamonds are used for two unrelated end uses: gem diamonds are jewels of great beauty, while industrial diamonds are essential materials of modem industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamonds in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (1.2 to 1.4 mm). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite", General Electric's Compaxa and Stratapax", and Megadiamond's Megapax" have replaced natural diamonds in turning tools, mining and oil drilling bits, and dressing tool applications. Industrial Diamonds The diamond is by far the most important industrial abrasive. As recently as 50 years ago, consumption of industrial diamonds was less than that of gem diamonds, but since that time, industrial use has grown to a position of great dominance. During the six-year period 1929 to 1934, the material produced for industrial use amounted to about 74% by weight of the world's total output of diamonds. In 1989 the percentage of natural industrial diamonds mined in the world was 55%. When synthetic industrial diamonds are added to the natural industrial diamond figures, this percentage becomes 87% of total world diamond production including gems, near gems, industrial, and synthetic stones. The many uses responsible for these significant increases are dependent on the properties of the diamond, including hardness, cleavage, and parting, optical characteristics, presence of sharp points and edges, and capacity for taking and maintaining a high polish. The utilitarian role of the diamond was confined primarily to lapidary products until the industrial revolution, which created the first demand for diamond as an industrial tool. In 1777, a British inventor and instrument maker, Jesse Ramsden, used a diamond to cut a precision screw for an engine that he had invented. The first authentic description of industrial diamonds being set in a saw was recorded in 1854 by a Frenchman, Durnain. Eight years later a Swiss watchmaker, Jean Leschot, developed the first diamond drill bit for use in a hand operated machine, which was employed to drill blastholes in rock. In 1864, diamond bits were put to their severest test up to that time in the construction of the Mont Cenis Tunnel in the Alps. A few years later a steam-powered diamond drill with a speed of 30 rpm was able to penetrate rock at the modest rate of 0.3 m/hr. As the industrial revolution gained momentum on both sides of the Atlantic, metal replaced wood and machines replaced people. Thus the foundation was laid for precision engineering and the recognition of diamonds as an indispensable tool of industry. The next major demand for industrial diamonds came after World War I with the development of cemented carbide cutting tools. Diamond was found to be the most effective medium for finishing and grinding the new ultrahard metal. This discovery rapidly increased the demand for industrial diamonds. The availability of inexpensive diamond material inspired tremendous research into applications. By 1935, the first successful phenol-resin grinding wheel containing diamond had been marketed. Soon afterward, the metal-bonded and vitrified diamond wheels were produced, and, as the matrices and bonds that held the diamond grit in place began to improve, the popularity of diamond grinding wheels grew. The outbreak of World War II, and the accompanying increase in use of hard-metal tools in the munitions industry, increased the demand for industrial diamonds. Since about 1950, the development of ultrahard ceramics, semi- conductor materials, plastics, and exotic metal alloys has further consolidated the diamond's position as an indispensable tool of industry. Only diamond is hard enough to cut these superhard materials with the precision, speed, and economy that industry demands today. Special machines equipped with industrial diamonds are used to remove bumps from concrete runways and highways and to modify highway surfaces in order to prevent skid accidents. Many skids are caused by hydroplaning, a phenomenon that occurs when the roadway is wet. Tires mount a film of water and virtually lose contact with the road surface. Diamond machines cut neat, narrow

Jan 1, 1994

By Frank F. Aplan

Introduction Heavy media separation (HMS), also called dense media or float¬sink separation, is one of the newer forms of gravity concentration. Though the concept can be traced to the last century, the process has enjoyed its major growth since 1940. Heavy liquid separation is a mutation. The heavy media process is used extensively to clean coal and for the concentration of a wide variety of ores such as those of iron, lead-zinc, chrome, manganese, tin, tungsten, fluorspar, magnesite, sylvite, garnet, diamonds, gravel, etc. It may be used where ever a significant density difference occurs between two minerals, and commercial separations are typically made in the range of 1.3 to 3.8 sp gr. The particle size treated ranges downward from 6-8 in. top size. Particles greater than about 1/16-in. (10 mesh) may be treated in a "static" bath, though for reasons of separation efficiency, + 1/2 -in- feed is usually preferred. For particles less than this size, separation in a heavy media cyclone is generally used. The flowsheet of a typical heavy media process, in this case one using a ferrous medium, is shown in Fig. I. In essence, the process consists of: (1) preparation of the feed usually by wet screening to remove undesired fines, (2) heavy medium separation, and (3) removal and recovery of the medium from the separated products. Many muta¬tions of the basic scheme are possible and numerous options are possi¬ble. HMS offers the following potential advantages:12 1) Ability to make sharp separations. 2) Ability to change the specific gravity of separation quickly to meet changing conditions. 3) Ability to remove products continuously. 4) Ability to treat a broad size range of products. 5) Ease of start-up and shutdown without loss of separating efficiency. 6) Relatively low medium cost and low media losses. 7) Low operating and maintenance costs. 8) High capacity with the use of relatively little floor space. 9) Relatively low capital investment per ton of capacity. The process may be used to produce a finished concentrate, two finished concentrates, or a concentrate and a middling of differing quality, or a preconcentrate by rejection of unwanted gangue. It is an ideal method for the reprocessing of coarse waste dumps. The greatest use for the process lies in coal cleaning and in the preconcentration of ores. The relatively inexpensive heavy media process may be used advantageously to reject large quantities of coarsely crushed gangue. When used in this way, the process will allow: (1) the use of lower cost but less selective mining methods with the "overbreak" material being removed at the front end of the concentrator or preparation plant; (2) a substantial reduction in the quantity of ore that must be finely ground for subsequent mineral liberation and separa¬tion. Since comminution is often the single most expensive step in beneficiation, it is desirable to eliminate as many essentially barren pieces of rock as possible before the grinding step, (3) a decrease in overall plant capital cost per ton of concentrate since the size of the plant from the dense medium step onward will be smaller. Several general references are available,12-18 though much of the technical data on the process is widely scattered in the general litera¬ture. Heavy Liquid Separation Organic Liquids Given sufficient settling time, it is possible to make a perfect separa¬tion between two particles of differing density by placing them in a liquid whose density is intermediate between the two. This means of achieving a perfect separation has proven to be elusive because of problems in feed preparation, particle settling rates, operational considerations, and economic constraints. There are a wide variety of heavy liquids that could be used, most of them halogenated hydrocarbons, and a few typical examples are given in Table 4. These liquids are most commonly used in ore dressing for the laboratory fractionation of ore particles on the basis of specific gravity. Laboratory Separations. Using liquids typified by those given in Table 4, separations are made to develop either the standard washability curves used to estimate the response of a given sample to gravity concentration or to prepare a partition curve to evaluate the effective¬ness of a given gravity separation process or piece of equipment. A typical washability curve is given in Fig. 2.19 Such curves are generated for raw coal, e.g., by treating either the whole or various size fractions of the sample in a series of heavy liquids and analyzing the various specific gravity fractions so produced. The procedure is relatively simple for coal samples because of the ready availability of a wide variety of relatively low cost heavy liquids in the density range 1.2¬-2.0. For ores the problem is much more complicated, because only a few high density liquids, all of rather high cost, are available. Parti¬tion curves are generated in the same manner by treating the separated products in the same liquids. Greater details on the procedures to be used in heavy liquid separa¬tions are to be found in the literature (for coal, Refs. 13, 14 and 19 and for ore, Refs. 20 and 21). For testing coal, calcium and zinc chloride solutions have been used extensively in the past, though today halogenated hydrocarbons (available under the trade name Certigrav) are the preferred media. The liquids shown in Table 4 may

Jan 1, 1985

By J. M. Rios

This paper exposes the reasons that led the Empresa Nacional Minera del Sahara, S.A. (ENMINSA) to the selection of a conveyor belt system for the transport of phosphate rock over a distance of 100 kilometers. ENMINSA was created in 1962, with the main objetive of the exploitation of phosphate rock deposits in the Spanish province of Sahara, in North West Africa. Poor grade outcrops were known previously. A detailed geological research carried over the province led ENMINSA to the discovery of deposits not exposed, and of much higher grade. The sector known as Bu-Craa was chosen as the most promising, and was explored by means of drill holing and shafting. The important amount of information obtained permitted a detailed evaluation of the capacity and grade of the rich ore contained in the Bu-Craa area. Simultaneously with the systematic reconnaissance of the Bu-Craa deposits, ENMINSA developped the study of the technical and economical problems required for the beneficiation of the rock, which comprised five main groups of projects: rock exploitation; beneficiation plant; rock transport from the mine site to the Atlantic coast; storage, handling and loading facilities by the sea- side, and power plant. Once determined the location of the marine loading facilities, which to date are in an advanced stage of construction (figs. 1 and 2), the studies conductive to the selection of the best transport system from the mine to the ocean, along 100 kms. distance were undertaken.

Jan 1, 1968

By A. G. Royle

Although these exhibit similar structures overall, there are more acute valuation problems in alluvials. Most of this description will therefore be about alluvials with comments on bedded vis-a- vis alluvial deposits where necessary. Although geological comments refer mainly to lateritic deposits the method of valuation described applies to all bedded deposits, e. g. coal, limestone, phosphate. In general, the more a deposit suffers alteration during or after its formation and the more the sampling process disturbs its material, the greater the difficulties of valuation. Emphasis is laid on structure, as in any kind of deposit valuation cannot proceed until its structures are understood. Not all the structures found in alluvials will occur in bedded deposits, of course.

Jan 1, 1982

By JA Vallejos

High stress underground mining poses a significant challenge to rock mechanics and rock engineering. To overcome theses challenges significative improvements in solutions and best practices of the design and operation of mines under high stress have been developed and implemented. This paper presents certain topics related to the management of high stress for sustainable underground mining. The topics include; the effect of preconditioning techniques (destress blasting and hydraulic fracturing) in the seismic rock mass response to underground mining and the dynamic behaviour of rock support systems. The opportunities associated with research in rock mechanics and practical rock engineering are discussed.

Apr 26, 2022

By L. Mao

A first-order flotation rate equation was derived by incorporating both hydrodynamic and surface forces involved in bubble-particle interactions. The hydrodynamic forces were calculated using an appropriate stream function, while the surface forces calculated using the extended DL VO theory. The equation was used to predict flotation results as functions of several important parameters such as contact angle, Zeta potentials of air bubbles and particles, and bubble size. The predictions are consistent with experience, and can be explained in view of the various sub-processes considered in the model.

Jan 1, 1997