Search Documents

By Alden B. Carpenter

Brines (a solution containing more than 100,000 mg/l dissolved solids) in sedimentary basins are genetically related to evaporites in one of three ways: (1) dissolution of evaporite minerals, generally halite; (2) interstitial fluids in evaporites which are expelled from their source rock during compaction; (3) incongruent alteration of hydrous evaporite minerals (carnallite). Most brines of commercial interest originate as interstitial fluids in halite-rich rocks. These fluids are initially rich in magnesium, sulfate, and potassium but evolve in composition to an Na-Ca-Cl brine during their migration to their present host rock. A particularly important reaction in this process is: 2CaCO3 + Mgt+ = CaMg(CO3)2 + Cat (1a) This reaction reduces the magnesium content of the brine and ultimately converts it to a calcium-rich brine. The loss of sulfate occurs by two mechanisms. One of these is by direct precipitation as calcium sulfate (either as gypsum or anhydrite): Ca 2+ + SO4 2- = CaSO4 (2a) Additional sulfate may be lost from the brine by sulfate reduction: S042 + 1.33CH2 + 214- = H2S + 1.33CO2 + 1.33H20 (3a) The loss of carbonate species occurs by precipitation as carbonates: H2O + C02 + Cat = CaCO3 + 2H+ (4a) The net result of reactions 3 and 4 is: Ca 2+ + SO4 2- + 1.33CH2 = H2S + CaCO3 + 0.33H2O + 0.33CO2 (5a) The loss of potassium from brines is caused by the formation of potassium aluminosilicates: 2K+ + Al2Si2O5 (OH)4 + 4SiO2 = 2H + 2KAlSi2O8 + H2O (6a) The hydrogen ions produced by this reaction dissolve carbonates: 2H+ + CaCO3 = Ca 2+ + CO2 + H2O (7a) The net result of reactions 6 and 7 is: 2K+ + CaCO3 + Al2Si205 OH)4 + 4SiO2 = Ca2 + 2KA1Si3O8 + H2O + C02 (8a) A study of brines from central Mississippi has shown that the composition of these brines is related to the interaction of pore fluids from evaporites with minerals in the enclosing sedimentary rocks.

Jan 1, 1978

By St. Mergentime, K. Zeidler, V. Gall

2001, the New Jersey Transit Authority commissioned the JV Merco-Obayashi with the rehabilitation contract of the approximately 130-year-old, 4,200 ft long, partially brick- lined Bergen North Tunnel. The contract entailed the tunnel enlargement, shotcrete and rock dowels initial support according to the NATM, a waterproofing system, tunnel drainage and a cast-in-place concrete lining. The rock conditions encountered required design adaptations and significant modifications of the initial tunnel support. Flexibility, skill and extensive experience on the Authority’s and Contractor’s side finally lead to a success. This paper describes the operations and design modifications carried out.

Jan 1, 2003

By David P. Keller, George Podolsky

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The world production of iron oxide pigments is estimated by the authors to be between 350 and 400 kt. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test which now has some 20,000 years of exposure. In addition to abundance, iron oxides (about 7% of the earth's crust) have the advantage of low cost, permanency, and are non- toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when these properties were desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States, the combined production of natural and synthetic iron oxides produced sales of over $97 million in 1980 (Spimad, Jr., 1980), increasing to $138 million by 1990 (Templeton, 1990) NOMENCLATURE With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products that are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a competitive commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and are able to command a premium price over iron ores used for steel manufacturing. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary particles are produced as opposed to the use of comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1994

By L. W. Pommier

In the field of minerals processing the concentration of valuable minerals normally takes place in suspensions of ore particles in liquids. The fluid resistance offered by Newtonian liquids to the movement of free settling spheres for the limiting cases of creep flow and turbulent flow is well described by Stokes' and Newton's Laws. However, these equations are not applicable to non-Newtonian fluids, since the relationship between applied shearing stress and resulting rate of shear is a non-linear function, and more than one viscosity parameter is necessary to describe their rheological properties. For this reason, the term "apparent viscosity," which has been commonly used to explain the flow resistance of the non-Newtonian systems including suspensions, may be misleading. A rigorous analysis of the mechanisms of momentum transport of solid-liquid systems is complex indeed. There are many variables that affect the properties of such systems, and precise limitations and assumptions are necessary in order to produce quantitative relationships for predicting their behavior. Very dilute suspensions of spherical particles in Newtonian liquids of identical density as the solids have been examined in the past (12); however, the study of suspensions in which there is a considerable difference in density, between the liquid and the suspended solids has been neglected.

Jan 1, 1968

By Clay Haynes, Tim Pearia, Robert Robinson, Judy Cochran

A 1.89 km-long, 4.5 m-I.D. tunnel was successfully constructed through saturated hard clay, and highly abrasive dense sand and gravel, with groundwater heads ranging from 10 to 20 m. In order to address these conditions, a Lovat earth pressure balance TBM was used, with soil conditioning by foam, water and various polymers. Support was provided by a single-pass segmented concrete lining. Groundwater inflows of 400to 1,600 lpm at times created challenges for changing cutting tools. Surface settlements were generally less than measurement thresholds, except under very low cover at startup. This project provides a pivotal case study of the successful application of EPBM technology in saturated, abrasive glacial soils and the successful application of soil conditioners.

Jan 1, 2003

By L. E. Allen, J. F. Abel, D. R. Morgan

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the U.S. Department of Energy (DOE). The repository is located at a depth of 655 m in the Permian age salt beds of the Salado Formation, 40 km east of Carlsbad, NM. A key component in the design of the WIPP repository is the installation of concrete structures as panel seals in the intake and exhaust drifts after a panel has been filled with waste containers. The DOE has proposed several panel closure design modifications to the EPA. EPA approval of the changes is required since the details of the designs are specified in EPA’s final rule as a condition for WIPP certification. The Environmental Evaluation Group, in its role of providing technical oversight on the WIPP project, has evaluated the proposed modifications. An analysis of this evaluation is discussed.

Jan 1, 2003

By Vladimir Adamek

Due to the variability of subsidence characteristics across the U.S. coalfields, it was concluded that it would be practically impossible to develop a universal predictive model for mining-induced subsidence based on theoretical assumptions. Therefore, an effort was made to find a procedure to develop an empirical subsidence predictive model based on a sufficient Mount of field data from one mining area (in this case the Northern Appalachian Coal Region). It was also thought that this procedure, if successful, could be used as the template for developing predictive capabilities for other coalfields with different subsidence characteristics given a reasonable amount of field data. It has been found, in the Northern Appalachian Coal Region, that the variability of subsidence characteristics can be expressed by a polynomial equation developed through regression analysis of the variable subsidence coefficient and derived directly from the field data. In this study, field data were obtained from 11 Bureau longwall panel studies (16 half profiles) for static subsidence and 14 panels for dynamic subsidence. The effects of lithology, expressed in the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hythetically homogeneous overburden and existing ithological conditions. For each longwall panel, the characteristic of the variable subsidence coefficient was defined along individual static profiles. The definition of mean values with acceptable deviations is the substance of the predictive method. The same procedure was used to develop a predictive model for dynamic subsidence, since it war discovered that the rate of longwall face advance is not a necessary functional parameter. This paper presents the theory, development, and application of the static and dynamic subsidence prediction models.

Jan 1, 1986

It took me nearly nine months to make the move from Arizona to Berkeley, opening an office and planning our new home. While I was in Warren Dorothy had rented two rooms for my office In the new California Commercial Union Building at 315 Montgomery Street in San Francisco. She made such a good choice that this remained my address for more than 50 years Dorothy had also looked over many lots In Berkeley, and took an option on the one that pleased her the most. It was a beautiful lot, or rather three, as we took three lots to protect our view. The only possible drawback was that it was in a new district and there were only two houses within two blocks. No one could tell how the area would develop but we liked it so much that we bought the lots on the spot and signed a note to guarantee payment. Dorothy's good judgment was shown by the fact that after 50 years we are still glad to be living on the same property, at 168 Southampton Avenue. We arranged a meeting with the distinguished architect Bernard Maybeck-and employed him to design a house for us. Dorothy spent most of her time with Maybeck planning the house and an attached studio for her, and she later wrote an amusing essay on her dealings with Maybeck. They were so successful that even now we could not think of any changes we would have wanted. It took several months to design a house that suited Dorothy and would fit on our hilltop. I was glad to overcome some of Maybeck's scorn for "only an engineer" by showing how, by rotating the studio addition 45º, it would fit the lot without serious excavation. We finally signed a contract with Maybeck, borrowing so much money that it scared us. First Consulting After short jumps to the gold mines in the Secret Pass District near Kingman, Ariz., and to the Espiritu Santo prospect adjoining the rich

Jan 1, 1976

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By Walter C. Labys, William A. Vogely, David O. Wood

INTRODUCTION The past decade has witnessed a literal explosion in formal modeling of energy systems and markets. This rapid development was stimulated primarily by policy issues arising from the energy price shocks of 1973- 1974 and 1979- 1980. The suddenness of this interest is illustrated by comparing the current and earlier editions of Mineral Economics. The third edition, published in 1976, includes an addendum to the section of projection and forecasting methods because, Since the foregoing chapter was written, major events in petroleum have caused an explosion in formal modeling efforts in the energy field.a In contrast, this fourth edition includes the present chapter on energy modeling, and a separate chapter on nonfuel minerals modeling. The considerable interest in formal energy models is based on the complexity of the system, in particular the interaction between technical and engineering data and designs, and economic behavior of energy producers and users. Energy is a vital component in the economic and social well-being of nations, and must increasingly be explicitly considered in developing economic growth and welfare policies. Energy models can contribute to policy development and analysis, both by improved understanding of the energy system, and of the interaction between energy markets and the economy, and as an explicit means of analyzing and comparing the implications of alternative policy actions. At their best, formal models can clarify and illuminate policy options. In this chapter we will survey the objectives, methods, and potential contributions and limitations of energy system modeling. Section 2 considers the objectives, scope, and approaches to energy system and market modeling. Methodological approaches are then discussed more formally in section 3. Our approach is to intro- duce each model type and method via relatively simple generic models, illustrating their use by a selective review of the applications literature. Section 4 shifts the focus from modeling methods to procedures for model evaluation and improving model credibility especially in policy research and analysis. We conclude with some brief remarks on directions and opportunities for future modeling research. ENERGY MODELS: OBJECTIVES, SCOPE AND APPROACHES The concept of a model usually evokes an image of a complex, computerized system of mathematical or econometric equations providing detailed information concerning the operation of the process being modeled. In fact. models may be simple or complex, formal or mental, depending upon the purposes for which the model is intended. Simple judgmental models may be most appropriate when monitoring the overall performance of a process. When more detailed information is required and/or when the model

Jan 1, 1985

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By E. F. Schnitzer, C. Lidstone, D. Cramer, P. J. Wampler

The River Island mining site is located at approximately river mile (RM) 15 on the Clackamas River, a large gravel-bed river in northwest Oregon. During major flooding in February 1996, rapid channel change occurred. The natural process of meander cutoff, slowed for several years by dike construction, was accelerated by erosion into gravel extraction ponds on the inside of a meander bend during the flood. In a matter of hours, the river cut off a meander and began flowing through a series of gravel pits located on the inside of the meander bend. The cutoff resulted in a reduction in reach length of approximately 1,100 m. Erosion by bed lowering, knick point retreat and lateral erosion of upstream river banks occurred quickly. Within two days of the peak flow, 3.5 hectares of land and 105,500 m3 of gravel were eroded from the river bank just above the cutoff location. Much of this gravel moved a short distance downstream into the excavation. Reach slope increased from 0.0022 to approximately 0.0035 in the cutoff reach. Between 1996 and 2003, the knick point from the meander cutoff has migrated 2,290 m upstream, resulting in increased bed load transport, incision, and local lowering of the water table. In 1993, prior to the meander cutoff, transects were surveyed in the River Island reach upstream of the cutoff location. Resurvey of these transects and aerial photo analysis indicates that 96% of the knick point migration occurred during the first winter following meander cutoff. Connection of the flowing river to the off-channel ponds has had minimal effect on water temperatures in the mainstem Clackamas River. It is likely that this minimal change in temperature will decrease as ponds are isolated from active river flow by gravel bar deposition. Fish net-ting in spring 2002, suggests that salmonid use of the pond in the spring is minimal. The most abundant native species netted were large-scale sucker and northern pikeminnow. The most abundant non-native species netted was brown bullhead. Early regulation by state and federal agencies did not adequately evaluate potential impacts to the river and the floodplain; nor did it evaluate future impacts related to geomorphic processes and sediment transport. New permit evaluation methods, currently implemented by both Oregon and Washington, incorporate 1) river dynamism through historic river migration analysis; 2) stability of human structures in light of river dynamics; and 3) sediment transport and its impact on channel stability and dynamics. The gravel pit capture at River Island highlights the potential risks of mining in an active secondary channel of a large gravel-bed river. Mining deeper than the depth of the adjacent channel, within the active migration zone, may increase off-site impacts. In locations where multiple gravel excavations are present within the meander zone, a comprehensive reclamation and restoration plan should be developed which provides long-term channel stability within the natural variability of the entire river reach.

Jan 1, 2006

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985

By Edie Trimmer

Utah statute defines sovereign lands as "those lands lying below the ordinary high water mark of navigable bodies of water at the date of statehood, and owned by the state by virtue of its sovereignty." The lands within the bed of Great Salt Lake (GSL) are, by this definition, sovereign lands, acquired at statehood in 1896 in accordance with the "equal footing" doctrine, granting each state control and ownership of navigable waters and the lands underneath those waters within its borders. Under public trust doctrine, the state, as trustee for the people, bears responsibility for preserving and protecting the right of the public to use of the waters for navigation, commerce, fishing, recreation, and wildlife habitat. Also by statute, sovereign lands are defined as "state lands," to be managed by "multiple use sustained-yield principles." The Division of Forestry, Fire and State Lands is given management authority for sovereign lands and, as manager, has responsibility to prepare comprehensive plans, initiate studies of the lake and its resources, implement comprehensive plans through state and local entities, and coordinate the activities of various divisions within the Department of Natural Resources (DNR). The Division of Forestry, Fire and State Lands also has responsibility for management of mineral leasing on sovereign lands. The many resources on the lake--water, minerals, wildlife, recreation, archeological and historical values--are managed by as many state agencies which occasionally creates conflicts. The brines of GSL contain several ions that crystalize into valuable minerals during evaporation. The major ions in the lake are, in order of relative abundance, chloride, sodium, sulfate, magnesium, and potassium. Mineral products which are currently extracted from lake brines are sodium chloride, magnesium chloride brine which can be sold as flake magnesium chloride or further processed into magnesium and chlorine gas, and potassium sulfate. Mineral products which have potential for extraction include gypsum, sodium sulfate, and trace amounts of lithium, boron, and bromine. The GSL contained an estimated 4.3 billion short tons (st) (3.9 billion metric tons [mt]) of dissolved salts in 1998. Utah Geological Survey (UGS) estimates of the dissolved salt content in GSL have fluctuated from 4.0 to 5.5 billion st (3.6 to 5.0 billion mt) due to the dynamic conditions in the lake as salts are precipitated and redissolved, and due to the diversion of brines from GSL, such as the West Desert Pumping Project. The lake has four areas of varying salinity, separated by dikes or other man-made structures: north arm and Stansbury Bay brines at near saturation (25 to 27 percent total dissolved solids [TDS]); the main body of the south arm with concentrations ranging from 7 to 15 percent TDS as lake elevations fluctuate; the waters in Farmington Bay at approximately 3 to 5 percent TDS; and Bear River Bay at <1 to 7 percent TDS. The percent TDS in Bear River Bay fluctuates with lake level, and changes in Bear River inflow. The transfer of salts from the south arm to the north arm has raised questions about the viability of the mineral and brine shrimp industries. The UGS and the U.S. Geological Survey (USGS) continue to monitor salinities at designated sites on the lake to document changing lake salinity. A recurrent theme is that placement of dikes and diversions can have significant and rapid impacts on various conditions in the lake. Hydrocarbon resources on the lake are significant, but presently undeveloped. The hydrocarbons are low gravity (4 to 9 degree API) and tar-like, contain high nitrogen concentrations, and up to 12 percent sulfur. The unusual characteristics of the oil have been the subject of studies by chemists at Weber State University and University Louis Pasteur de Strasbourg. However, these resources are difficult, and at present, uneconomic to extract using current technology because of the nature of the hydrocarbons, and production in "an offshore, highly saline environment." Oolitic sand deposits make up many of the beaches and shorelines around the lake. Because of their high calcium carbonate content, oolites have been used by Magnesium Corporation of America (MagCorp) and its predecessors for acid neutralization and dike construction. Oolites are also used in very minor amounts in flower drying. The Utah Division of Oil, Gas and Mining reports up to 130,000 st (118,000 mt) mined annually by MagCorp from U.S. Bureau of Land Management (BLM) lands adjacent to GSL. Currently, there are twelve producing mineral leases which generated slightly more than $1,000,000 in royalties during calendar year 1998. IMC Kalium Ogden Corp. (IMC Kalium) produces potassium sulfate and magnesium chloride from brines concentrated through solar evaporation in Bear River Bay and Clyman Bay. By-product sodium chloride is transferred to IMC Salt, which packages and sells the salt. MagCorp produces magnesium metal from brines concentrated in Stansbury Bay. Cargill Salt produces sodium chloride from brines provided by MagCorp under a lease agreement. Morton Salt produces salt at the southeast end of Stansbury Island. Lastly, North Shore Limited produces cocentrated brines for use in dietary and mineral/vitamin supplements near Spring Bay in the north arm of the lake. Producers of magnesium, potash, and salt from GSL contribute significantly to the value of metals and industrial minerals in Utah. Together these companies contribute approximately $240 million in gross value, or 18 percent of the value of the state&apos;s nonfuel mineral production. Most of this production is exported.

Jan 1, 2001

By R. D. Herron

Mining coal under deep cover conditions is certainly the proper phrase to use in describing one of our newest operations. Located in the southwest corner of Virginia is this operation which is the Beatrice Mine of the Beatrice Pocahontas Company, a joint venture of Republic Steel Corporation and Island Creek Coal Company. The mine is working in the No. 3 Pocahontas seam in an assigned area of over 9500 acres containing over 60 million tons of recoverable, high quality, low volatile coal. The site of the mine opening was at Keen Mountain, Virginia, where the seam lay 1350 feet below the surface. This depth, greater than anything attempted thus far in the coal industry on this continent, would pose some problems, we felt, with which we had not previously had to contend.

Jan 1, 1968

By B. Kolonja

This paper considers simulation of truck dispatching system designs using maximum expected production of the truck-shovel system as the measure of performance. Two methods are utilized, multiple comparisons with the best (MCB) and the combination of MCB and the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. The results show that the combined procedure of MCB with CRN is the superior tool to reduce the total number of replications needed to ensure the specified probability of correct selection over the finite number of designing systems. In this case study, MCB with CRN reduces the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1994

By Lloyd H. Yeager

Good morning gentlemen. I&apos;m very pleased to be a part of this fine program for the Society of Mining Engineers. Gypsum, as many of you know, is one of the most unique minerals on earth. The very excellent presentations which you have just witnessed, revealed the geological aspects of gypsum operations. It is not our purpose this morning to pursue this subject further. Instead, we felt you would be interested in some of the uses of gypsum . . . and what the future holds for gypsum products. To help accomplish this, we&apos;re going to first show the Gypsum Association&apos;s new film, "Shape Of The Future. &apos; This short movie traces gypsum f ram mines and quarries to its ultimate destination in homes, schools, offices -- in virtually every type of construction. We think you&apos;ll be particularly interested in the description of gypsum&apos;s fire resistive nature.

Jan 1, 1965

By W. K. Utt

This report discusses U.S. Bureau of Mines&apos; research involving modem vehicle position determination techniques in surface mining. The applications would include haul trucks, power shovels, and drilling rigs. Accurate position determination of these vehicles in near real-time is expected to result in safer and more efficient mining operations. The requirements for a vehicle position monitoring and warning system were determined. After screening several concepts, the global positioning system (GPS) and a radar positioning system were selected for further evaluation. A state-of-the-art GPS receiver was taken to a surface mine to assess the feasibility of receiving the satellite signals. A state-of-the-art radar positioning system was evaluated with regard to accuracy.

Jan 1, 1995

By Chee S. Theng

As the 2017 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2017 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 342. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2017 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH), a special review article on Heap Leach Modeling, and articles from two Special Issues on Rare Earths. The 2017 Transactions consists of a total of 54 technical papers, encompassing all 21 papers published in 2017 in the Technical Papers Section of Mining Engineering (Vol. 69) and all 24 papers published in 2017 in Minerals & Metallurgical Processing (Vol. 34). Additionally, this volume contains 9 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2017 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2017