Search Documents

By Thomas R. Kuesel, Harvey W. Parker

INTRODUCTION This paper describes the use of a shield and compressed air for construction of a short section of a pair of twin single-track tunnels for the Metropolitan Atlanta Rapid Transit Authority (MARTA) transit system. Although only two blocks long, this section posed the greatest difficulties to both engineers and contractors, and is the most expensive section of line construction on the MARTA system. All this derives directly from its setting--these tunnels had to be constructed through mixed-face conditions. SETTING The Broad Street tunnels form a link between the Peachtree Center and Five Points Stations, in the heart of Atlanta's central business district (Figure 1). Peachtree Center sits atop a solid rock ridge, which inspired the design of a deep rock-mined station, as described in the 1979 RETC. Five Points Station is MARTA's hub--the intersection of the system's two main branches. It is located in the old railroad gulch, a filled-in erosional valley at the base of Peachtree Ridge, and was constructed by open-cut methods. The alignment and profile of the Broad Street tunnels were closely constrained by these two adjacent anchors, and in the six-block stretch between them there was very little room for maneuvering. Since the rock ridge petered out about in the middle of the section, it was evident at the outset that there would be about two blocks of rock tunneling at the north end, two blocks of soft ground construction at the south, and two blocks of mixed-face in between. It is this central two-block section that is the focus of this paper.

Jan 1, 1981

By Allegra Yeley, Ted Klemetti, Gamal Rashed, Tim Miller, Nicole Evanek

In 2015, the Subtropolis Mine in Petersburg, OH, experienced a massive ground collapse that continues to grow over time. Horizontal stress effects have affected the roof at this operation in the past and may have played a large role in this collapse. Horizontal stress can impact the roof and floor stability and endanger the health and safety of underground stone miners. Mines experiencing damaging effects from horizontal stress typically find that the principal stress direction is the same throughout the mine and the region. At the Subtropolis Mine the principal horizontal stress direction appears to change as conditions change and differs from the regional horizontal stress, particularly near the collapse or other roof fall areas. The growth over time of this collapse and other roof falls have been captured and analyzed using geologic mapping, 3D LiDAR scanning, numerical modeling and geographic information systems like ArcGIS. Utilizing these tools to better understand sitespecific conditions can be critical to reducing the potential of massive ground collapses in the underground limestone industry.

Feb 1, 2024

By F. L. Pirkle, W. C. Bagby

The International Mineral Valuation (IMVAL) Committee, founded in 2012, develops strategies for conducting mineral valuations. These strategies have been developed into a mineral asset valuation template called the International Mineral Property Valuation Standards Template and is part of IMVAL's work to establish consistent international standards for mineral property valuation and reporting. This template is a living document that is updated from time to time and is based on three core values or pillars (Fundamental Principles): Competence, Materiality, and Transparency. Objectivity, Independence, and Reasonableness may be applied as required by national codes or standards. The Template harmonizes international standards for valuation of mineral assets as real property and represents a consensus of current good practices. It is not a stand-alone reporting code and does not supersede existing national reporting standards. The Template deals with mineral-property valuation as distinct from mineral-project evaluation. INTRODUCTION In his 1989 book, “The New Realities”, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, California, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized.” (p. 209) The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze, and interpret data that are material to a mineral valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality, and transparency, the three pillars of mineral valuation (“minerals valuation”, “mineral-property valuation”). The International Mineral Valuation Standards Template (“IMVAL Template”, IMVAL”, “Template”), third edition dated May 2018, defines mineral valuation as: “The estimation of the Value of a Mineral Property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the Valuation conclusion) or to refer to the preparation of the estimated Value (the act of valuing).” (p. 14) Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The Template deals with Valuation, which is distinct from Evaluation. The distinction inherent in these defined terms is that Valuation addresses the estimation of value of a Mineral Property, whereas Evaluation addresses the broader assessment of a Mineral Property for an investment decision.” (p. 2)

Jan 1, 2019

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"Drill and blast represent the most important, and sometimes the costliest processes in the mine. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum and Temeng, 2015). The use of available information to improve the drill and blast processes can be the difference between a wasteful process and one that is optimized for costs, safety and desired fragmentation. Mining operations have access to several types of data sets that include a variety of different systems. This information can be used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the drill and blast process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting across multiple sites, it becomes valuable to create auditable, automated and sustainable workflows for handling the information.In some cases, the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Wixom, Watson, 2007). The author’s initial implementation plan for the drill and blast solution included using data stored at the sites on local servers. However, we learned early in the process that much of the work for aggregating and supplying the required data was already completed and was available in the EDW ready for use. This saved time, reduced risk and added value to the system.The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, especially highlighting the value of using an EDW for managing drill blast information; and to discuss how technical challenges encountered during the implementations were resolved. This article targets users that want to better manage their drill and blast data or try to set up standardized workflows for using this information.This case study will discuss the process of implementing a drill-and-blast workflow at multiple sites within Freeport-McMoRan (FMI) using both data at the sites and information available from the EDW."

Jan 5, 2017

By T. W. Camm

"We hear all the time about the value of hard work and perseverance, and the part they play in the professional life of successful people. What we do not hear so much about are the many professionals who work hard and persevere, yet never seem to quite reach the level of success they aim for. Some current authors are beginning to give more attention to the part luck/black swans/outliers play in success. This is not a new phenomenon, Machiavelli had a lot to say about it back in the Renaissance. So how can knowledge of this dynamic help in a modern organization? INTRODUCTION Work hard and you will succeed. Go to the right school, major in the right degree, study hard, and get a good job. Look at the lives of successful people, and do what they do. Be all that you can be. You can be anything you want to be. Really? Those who are successful always get attention, people want to know what they did to reach such a high position. Invariably, at least part of their narrative will include hard work, wise insight, taking advantage of opportunities, etc. If they are of a more generous nature, they might also allow that building the right friendships and collaborations also played a role. All of this may be true; what we do not often hear are the stories of those who did all of these very same things, but did not find success. An example from pop culture: The Voice. I have watched this show occasionally the past couple of years. One of the things I like about the show is that the initial screening of contestants is based solely on their singing voice (hence the name of the show), and not on their appearance. At the time of this writing (early November), the judges have just finished elimination rounds for their final teams to go on to the live shows. Here is my point—in almost every case the judges agonized over choosing who would go forward and who would be eliminated. And the reason is because all of them are really talented singers. It is impressive how gifted they are. At the end of each season, only one is declared a winner, out of that gifted pool of singers. When you hear their stories, they are all talented, hard-working individuals sacrificing for their art. And as far as I know, none of them has ever become a star. Hard work, dedication, sacrifice, talent—sometimes it is enough, sometimes not. I will be looking at the part uncertainty/luck/black swans play in our lives, but I want to make it clear at the beginning that I am not saying everything that happens to us is out of our hands or beyond our control. Taleb makes this same point (2007, p. 52): “This problem is chronic: if you tell people that the key to success is not always skills, they think that you are telling them that it is never skills, always luck.”"

Jan 1, 2017

By E. J. Wasp

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the manufactured product. Clearly, the engineer who is responsible for selecting a mode of transport must base his decision, at least in large measure, on economic comparisons. And today, the engineer usually finds that he has to choose between several modes, including slurry pipelines. For the purpose of an initial economic screening, it is not necessary to go deeply into the technical details of a slurry system. What is usually needed, however, is a method with which the engineer can make a quick economic assessment to determine whether a slurry pipeline should be included in the detailed final analysis. This paper presents a rapid method for making such a preliminary appraisal. Experience with commercial slurry pipeline systems in several countries and with a variety of solid materials has shown that if several assumptions pertaining to critical design variables are made, it is possible to roughly estimate the transportation cost of a slurry system on the basis of only three factors: the specific gravity of the solid material, the length of the system, and the quantity of slurry to be pumped each year. It is assumed that conditions pertaining to field construction, corrosion inhibition, and the like, will be favorable. This assumption is critical because any factor which analysis shows to be particularly unfavorable will raise the total transportation cost estimate which this paper establishes. If the engineer employs this estimating procedure and decides that the use of a slurry pipeline is economically unattractive, his chances of being wrong are small. Conversely, if his quick appraisal indicates that the use of a slurry system is economically favorable, the engineer is justified in committing the time and money needed to make a more detailed investigation of the slurry pipeline potential.

Jan 1, 1969

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant's ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator's end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969

By John L. Shafer

A process for the conversion of stibnite (Sb2Sj) concentrates, crude antimony oxide, or metal to a pure cubic antimonous oxide (senarmontite) has been developed on a laboratory scale. The conversion of stibnite to senarmontite has been piloted. The high purity of the final product is the result of forming antimony trichloride as a low temperature distillable intermediate. To obtain the antimony trichloride the stibnite, or crude oxide is slurried in molten antimony trichloride and reacted with gaseous hydrogen chloride. Antimony metal is oxidized to the trichloride with chlorine. The hydrogen sulfide produced from the hydro- chlorination of stibnite can be upgraded to a strength of 95% or greater for further treatment. The crude antimony trichloride is separated from the gangue by a preliminary evaporation and then is fractionally distilled and the trichloride distillate has less than 50ppm of arsenic and lead combined (the most troublesome impurities in antimony processing). The purified antimony trichloride is then hydrolyzed with sodium or ammonium hydroxide to produce the cubic form of antimonous oxide (senarmontite) to the exclusion of the rhombic form (valentinite) which is photosensitive. The advantage of this process is the ability to treat a wide range of antimony ores, concentrates, and metal to yield a high purity oxide in a controllable range of particle sizes.

Jan 1, 1975

By M. Xing, S. Usman, K. Awuah-Offei

"While mines generally focus on achieving operational efficiency, creating shared value for all stakeholders is also a management goal. This includes taking a holistic view of their supply chains and increasing local participation. This paper examines the role of supply chain management in mine management; in particular the effect of a strong local supply chain on regional economic impacts. Using input-output analysis, the impact of a local supply chain on a mining sector’s regional economic impact is examined by increasing local sourcing (increasing local purchase percentage -- LPP) for 10 key commodities. An approach, based on multipliers and excess local capacity is used to identify key commodities. The impacts examined are sales, employment, labor income, and value added. The work is illustrated with stone mining and quarrying in Missouri. Ten percent increases in LPP of the key commodities, in this example, result in $4.1 million additional impact on the Missouri economy. This work can provide insight on how to better create shared value for all stakeholders. INTRODUCTION Little research has been published on improving mine supply chain management (SCM) to enhance regional economic impacts. Although some extensive academic research has explored the importance of an industries’ supply chain, not much is known about how a locally-based supply chain increases shared value in the resource sector. Across industries, traditional SCM is getting more and more complex. This is true of the mining sector as well. However, this increased sophistication is not directed towards increasing shared value for all stakeholders, particularly, the local communities. Further research is required to develop new SCM strategies that enhance local participation. One major point of difference between this work and traditional supply chain management is the inclusion of stakeholders’ shared value as a goal in SCM. Creating shared value has become a business goal in recent years (Porter and Kramer, 2011). The authors use input-output analysis (Leeuw, 2012) to evaluate the regional economic impacts of supply chain decisions, which is not part of traditional SCM. Although input-output analysis has been applied to SCM for decades, most of the research uses input-output analysis as a tool to advance an industries’ own operational efficiency (Accenture, 2014)."

Jan 1, 2015

By K. Lagnese, C. Robinson, S. Muddasani

"Mine water generated from underground coal mining operations contains both dissolved and particulate solids. Dissolved solids primarily consist of sodium, calcium, magnesium, potassium, chlorides and sulfates. When discharged to a receiving stream without treatment, these constituents create a potentially toxic environment for aquatic life. A case study is presented to discuss how a centralized treatment plant treats mine water from six locations to meet discharge limitations for chlorides. Located in West Virginia, this facility consistently achieves less than the NPDES permit limitation of 218 mg/L chlorides in the discharge while generating almost zero liquid waste. The dissolved solids concentration in the influent ranges between 5,000 and 10,000 mg/L, with chloride concentrations of 1,000 to 2,000 mg/L and sulfate concentrations of 2,000 to 6,000 mg/L. The mine water is treated using advanced treatment technology to produce clean water for discharge or reuse. The treatment process comprises aeration, softening, filtration, reverse osmosis, RO reject softening, evaporation, crystallization, final effluent remineralization and sludge dewatering. The solid waste generated in the treatment process is landfilled on site. The leachate is sent back to the facility’s thermal treatment process. Because no liquid waste leaves the property, this plant is termed a “Zero Liquid Waste” (ZLW) facility. INTRODUCTION The advanced water treatment system was built to meet a new 218 mg/l regulatory limitation imposed by the West Virginia Department of Environmental Protection for chlorides discharged to surface waters. The system is designed to treat a maximum flow of approximately 5 million gallons per day (795 m3/h) of mine water. The treatment process utilizes reverse osmosis (RO) membrane treatment to achieve the effluent criteria, and evaporation and crystallization technology to manage the RO concentrate from the water treatment process. As a result, the system produces clean water for discharge while generating zero liquid waste. The effluent water can be used for industrial purposes or discharged to a receiving stream. A Water Impact Index (WIIx) study indicated that discharge of this high-quality water into the Monongahela River watershed may improve the water quality for downstream water users. The waste produced in the treatment process, including softening sludge and salt, is disposed of in an on-site landfill."

Jan 1, 2015

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure, and other types of sensors are increasingly being used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP) while older forms of serial communication are being retired. This paper presents the selection, configuration, and testing methodologies that were employed by researchers from the National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide Internet Protocol data transport. INTRODUCTION To enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry [1]. However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology (IT) infrastructure in place to handle the data transport requirements for the newer IP-based technologies that are part of IIoT. This was the case with a mine in the Western United States; it lacked the infrastructure to perform critical monitoring in remote headings. The mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH’s) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder system to achieve IP data transport using commercially available land mobile data radios. DATA RADIO SELECTION The primary selection criteria for the data radios were network data format, modulation type, and radio channel spacing. The network data format decided upon was Internet Protocol. This format allowed for straightforward integration between the IP-enabled data acquisition system located in a remote heading and the network switch located in the control room. It also eliminated the added complexity of additional network hardware such as Ethernet to Serial converters. IP additionally provided a direct path to integration into higher bandwidth networks, such as fiber optic, should they become available."

Jan 1, 2018

By R. N. Chakravorty

Spontaneous combustion presents a very serious hazard to both safety and economics of mining operations. Notwithstanding considerable research that has been done over the years to present and control spontaneous combustion the risk still exists. Consequently, this problem poses a major challenge to mine safety researchers; new and improved techniques are constantly being developed to deal with this major hazard. This paper reviews the current practices to prevent and control spontaneous combustion in coal mine operations highlighting new developments in this area. Research and development work presently being carried out in Canada to' deal with this problem is also discussed which includes monitoring, inertization and application of biotechnology.

Jan 1, 1988

By Anthony W. Garson

Good morning, ladies and gentlemen: It is a pleasure to be here this morning as a representative of Dean Witter Reynolds; one of the foremost international investment firms in North America. My colleague, Hugh Wilmer (who will be speaking to you a little later), and I are involved as research analysts in the research and writing of published reports containing recommendations on the buying or selling of North American and South African gold and silver mining shares. Our talk this morning will focus on the gold mining operating costs of North American and South African gold producers. However, I am not going to bore you with reams of statistics on the operating costs of large numbers of gold mining operations; how meaningful would this data be to you? Instead, I will discuss what the investor should look for, and how he should use this knowledge in making his investment decision.

Jan 1, 1984

By E. J. Duggan

In the course of the grinding experiments conducted at Climax over the past twenty years one interesting phenomenon was discovered. This was that balls made of certain types of steel grind more ore than some others. The most significant variation was found in the results secured with a hard alloyed forged bail compared with the forged carbon ball supplied by most ball manufacturers These findings were confirmed in many repeated controlled tests. The value of these tests depends on the methods used, the facilities available and the care with which the investigations were conducted. These are described in the following. This testing has largely been done in eight 91 x 81 low discharge ball mills in closed circuit with 7811 duplex screw classifiers. The mills run at 20 RPM on a feed approximately minus 3/8 inch. The ore is ground through 28 - 35 mesh in one stage. Each mill and auxiliary classifier is in a separate, parallel grinding and flotation section The, ore to each: section is the same in every particular and is fed to each mill bin from a common conveyor tripper. The ore from the bin to the ball mill is weighed on a conveyor scale. The power input to each mill motor is determined with a watt hour meter which measures the power to the mill motor only. Both the scales and meters are checked periodically by standard methods and have been found to give consistent readings. Automatic samplers are employed on each section to obtain accurate measurement of the size reduction. A size analysis of the classifier overflow is made each shift and a composite size analysis is obtained from a weighted average of the various shift analyses. The mills are driven by 450 horsepower synchronous motors so that there is no speed variation and shell liner age is kept as nearly the same as possible in mills under test. The same set of operators is assigned to a mill under test as to the control mill. In all other particulars such as ball load, mill density, liner design, etc., the mills are operated in precisely the same manner. This is an ideal arrangement for plant testing. From observations of ball mill performance over the past twenty years, it is the opinion of the operating staff that variations of as little as one to two percent in mill capacities may be determined if sufficient operating hours are devoted, to a test. Relations between mill capacities, fineness of grinds and power consumptions have been established with a high degree of accuracy. In Table I are given the figures for one test. These show that while the grind with the hard ball was slightly coarser, the tons ground per hour was 5.4 percent greater with the soft ball, and 6.1 percent greater on the basis of minus 100 mesh produced. The power consumed per ton with the hard ball was 4.4 percent greater on a tons per hour basis. The soft ball was inferior in wearing qualities and steel consumption per ton of ore was 24 percent greater with it. In this test the mills were charged with the two different balls for a period of three months to allow the ball loads to come to equilibrium. In Table II are given the specifications of the two balls. The difference in grinding rates may be accounted for by the nature of the ball surfaces. The surfaces of the soft balls after being worn a while are rougher to the touch. Enlarged photographs of the worn-in surfaces of hard and soft balls are shown in Figure I. These show the presence of scratches or skid marks on the hard ball surface which indicates less nipping effect. The Climax ore pulp has a pH of 6.0 and is in a dispersed state. The viscosity is low compared with most ores especially those that are conditioned with lime. This would lower the tendency of the pulp to adhere to the balls with a lower grinding efficiency as a result. It was also thought that the relative rates of wear from surface to center might affect the make-up of an equilibrium ball charge. This probably has little effect on capacity as shown by the size analyses of the two ball charges in Table III. This hypothesis was subsequently investigated by the use of rationed charges. The rationed charge did not overcome the advantage in

Jan 1, 1958

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By Natalie White, Joel Asp, Allyz Kramer

"Minnesota has robust reclamation standards and have proven results in the taconite mining industry. Reclamation of overburden spoils, lean ore spoils and fine tailings from taconite production has generally been successful on the Iron Range, using a low input standard reclamation practice. Success at reestablishing vegetation on these landscapes is likely due to fairly favorable chemical and physical properties (e.g., few limitations due to acidic generating materials, metal toxicities and water and nutrient holding capacities). However, coarse tailings reclamation has proven more difficult, presumably due to lower nutrients and challenges with moisture holding capacities. Research efforts conducted since 1990 have struggled to develop a reclamation strategy for coarse tailings that meets the Minnesota Mineland Reclamation Rules, Chapter 6130. However, new breakthroughs in scram mining technologies are producing fine and coarse tailings that have not been encountered nor reclaimed in northern Minnesota. Scram mining in Minnesota is defined as those mining operations that produce natural iron ore concentrates. Innovative research is underway to investigate and determine successful reclamation strategies to reclaim scram mining tailings from these scram mining operations. The research program is conducted through collaboration with SEH, Prairie Restorations, Inc. (PRI) and Mining Resources, LLC with funding support from the Iron Range Resources and Rehabilitation Laurentian Vision Partnership minescapes grant program.The research program was divided into three phases:Phase I. Bench-scale testing to identify successful treatments to reclaim and restore scram tailings through evaluating surface soils amendments, viable seed mixes and plant germination, growth and densities. Phase I was completed in early 2015.Phase II. Field-scale pilot trial to test larger scale effectiveness of the treatments deemed successful in Phase I and test various vegetative assemblages and planting techniques focused on the unique challenges with scram tailing basins. Phase II was completed in late 2016 with a summary monitoring report.Phase III. Produce a technical report of results for the research undertaken in this study, as well as compile prior reclamation results used during previous Minnesota iron mining reclamation projects on tailings basin applications. Phase III was completed in 2017 with a summary monitoring report and recommendations."

Jan 2, 2018

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By M. E. Mellado

In this paper, we present an a posteriori validation of a heap leaching analytical model using sensitivity analysis. The model is suitable to represent the process of heap leaching of solid reactants from porous pellets and is based on a combination of the leaching kinetics at two levels: particle and heap. The validation is simple, and a sensitivity analysis can easily be performed. The simplicity of the analysis provides insight into the control and optimization of the heap leaching process without strong mathematical complexities. The model and the corresponding sensitivity analysis include the effects of heap height, particle sizes, flow rates and several operation-design variables. Using a case study, we discuss the importance of model validation based on sensitivity analysis. We also comment on several choices for optimizing the process. We had three goals in this work: a posteriori validation, highlighting the importance of model validation and providing insight into optimization choices. We can conclude that the model has good internal logic and there are no extra variables; i.e., all of the variables in the model are necessary.

May 1, 2012

By Charles H. Greene

This paper will describe briefly the steps taken in the development of a Central Florida phosphate ore deposit from acquisition to mining. Further, the design and early operation of the mining and beneficiation facilities will be depicted. During the 1950's, with confidence in the continually increasing requirement for phosphate fertilizer materials essential for producing food, I'. R. Grace & Cc acquired the Hookers Prairie tract containing approximately 45 million metric tons o. (50 million short ton~ of potential phosphate rock product. In 1973, at a point when the Grace captive need for rock was being greatly enlarged by a planned doubling of its Bartow phosphate chemicals plant capacity, the decision was made to expand existing phosphate rock production by building a new mine and plant. The initial annual capacity was to be 2.3 million tons (2.5 million st); however, subsequent investigation pointed to a higher than estimated dragline operating factor 'and the forecast of annual capacity was set at 2.5 million tons (2.8 million st).

Jan 1, 1977