Search Documents

By C. B. Cecil

The sulfur content of United States coal can be assessed by using a variety of approaches. The sulfur content may be expressed in terms of total sulfur in the coal, pounds of sulfur per million Btu, or sulfur remaining after reduction by coal preparation. In addition, the sulfur content may be applied to the demonstrated reserve base or to coal resource estimates. Unfortunately current data bases do not allow for an integrated assessment at the National level. Although classification of coal resources and reserves according to sulfur content is arbitrary, preferential production of low-sulfur reserves will positively skew the total sulfur of the remaining coal resource.

Jan 1, 1986

By K. N. Han, K. Peri, Y. Guan

The leaching behavior of gold in ammonical solutions with iodine as an oxidant was investigated using cyclic voltammogram and Tafel polarization. The majority of the experiments were carried out at 75°C, and the results were compared with consideraton given to the equilibrium of the iodine-ammonia system. The distribution of nine iodide-containing species at various pH values in the absence and presence of ammonia were considered at three different temperatures. It was found that, with the introduction of ammonia into the system, the concentration of iodide (I-), iodine (I2) and triiodide (I3-) is increased substantially, which in turn helps the rate of gold dissolution. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical-controlled mechanism.

Jan 1, 2002

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By Charles C. Y. Chen, Duane R. Skidmore

Batch leaching of Ohio #1, Ohio #4A and Ohio #5 coals was conducted with the thermophilic. sulfur, oxidizing microorganism: Sulfolobus acidocaldarius. Four different size fractions of each coal, with median sizes of 508, 200, 90, and 49 microns, were subjected for 10 days to leaching in a 5% coal-water slurry at 72°C and a pH of 2. Release rates and extent of sulfate and iron I1 and I11 ions from the coals during the leaching process and distribution of sulfur forms (sulfate, pyritic and organic) in the coal samples before and after treatment were determined. Data indicated that Ohio #1 coal, with an initial sulfur content of 0.6%, showed no significant changes with leaching in total sulfur content or forms of sulfur. The Ohio #4A coal, with initial total sulfur content near 5%, yielded product, for sizes below 200 microns with 90% reduction of pyritic sulfur while the extent of organic sulfur removal varied with coal particle size. Results similar to those for Ohio #4A were observed on the Ohio #5 coal, which had an initial total sulfur content of 3% and a final sulfur content near 1%. The findings were interpreted in terms of basic biological, chemical and physical mechanisms.

Jan 1, 1989

By H. Wilcox, M. Prichard, Y. P. Chugh

Environmental considerations related to the disposal of coal combustion byproducts (CCBs) and the impacts of deforestation associated with the harvesting of timber for utilization as roof supports in mines should become more severe in the future, as landfill space and suitable timber reserves become more scarce. To help address these concerns, lightweight artificial supports, such as post and crib elements, that use large percentages of coal combustion byproducts as aggregate have been developed for use in underground mines. These structural products show equal or better engineering characteristics than timber, and they have the potential to replace timber support in underground mines. CCB-based ultralight structural material (ULSM) has also been developed and commercialized for use in the construction of ventilation stoppings in underground mines. The bulk densities of these blocks range from 0.40 to 0.64 g/cm3 (25 to 40 lb per cu ft) with more than 75% CCBs. Efforts are also given to develop and demonstrate large volume CCB-based subgrade improvement technique for road construction. Soil treated with SIUC fluidized-bed combustion (FBC) fly ash developed an immediate bearing value exceeding 25% with a swelling strain of less than I %, which is greater than untreated soils, and met Illinois Department of Transportation (IDOT) standard specifications. In this paper, development procedures, engineering characteristics and beneficial uses of CCB-based structural products are given.

Jan 1, 2002

By Y. Wang, E. Forssberg, R. J. Pugh

The coagulation of dispersed ultrafine weakly-magnetic oxide mineral particles (e.g., natural hematite and chromite) in an external magnetic field can be described by interparticle forces. Essentially, coagulation occurs when the short-range London-van der Waals interactions and the long-range magnetic forces outweigh the stabilizing electrical double-layer repulsion. Using the classical colloid chemistry theory, the various components of the potential energy for different-sized particles at a series of ionic strengths and magnetic field intensities were calculated. The results of this theoretical analysis were then related to the results obtained from experimental studies in which the magnetic field-induced coagulation of the ultrafines of natural hematite and chromite in aqueous suspensions were investigated using a laboratory-scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, the maximum coagulation occurred near the pH of zero-point-of-charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, the long-range magnetic forces enabled coagulation to occur in the "secondary minimum." This caused the formation of chains that appeared to be relatively stable during sedimentation.

Jan 1, 1995

By A. E. Reisenauer, R. W. Nelson, G. W. Gee

A model assessment was made to evaluate contaminant transport to ground water from clay-lined and unlined tailings pits. The input hydrologic soil characteristics were measured on materials typical of those found at the Morton Ranch uranium mill site in central Wyoming. The assessment involved combined saturated and partially saturated flow and contaminant transport models for two-dimensional cross-sections typical of the proposed Morton Ranch burial pits. Specifically obtained from the models were contaminant flow paths, the advancing contaminant flow fronts for sorbed and non-sorbed constituents, and travel times of contaminants along flow paths. Such results enable evaluation of the environmental consequences for the alternative control methods.

Jan 1, 1980

By D. H. Y. Tang, S. S. Peng

Three-dimensional finite element modeling (3-D FEM) was performed to analyze the safety factors of stump pillars, 5.5 m x 5.5 m, under a cover of 63 m using the Modified Drucker-Prager Theory. The results showed that they were safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and analyzes the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By Y. Nakahiro, T. Wakamatsu, M. S. Elsalmawy

The flotation of quartz, feldspar and alumina was studied as a function of pH when using N-alkyldiamines as collectors. The lengths of alkyl chains of diamines were 8, 9, 10, and 12 carbon atoms. It was found that shorter hydrocarbon chain length of alkyldiamines has stronger tendency to float quartz while the feldspar responded poorly to flotation with these collectors at high pH values. The effect of addition of nonionic surfactant of Brij type, when using dodecadiamine as collector, was investigated. Flotation studies in the absence and in the presence of sodium dodecylsulfonate were carried out. These studies have indicated that sodium dodecylsulfonate, in the concentration studied, functions as strong depressant for feldspar.

Jan 1, 1995

By Y. H. Alghamdi, A. D. S. Gillies

"INTRODUCTION Background Diesel Particulate Matter (DPM) has been a critical issue during the last decade in underground mines. This problem is threatening the health of mine workers, as well as the mine’s productivity. It has been confirmed that the diesel engine exhaust is the main source for the diesel particulate matter (DPM), and that it has the highest impact in raising carbon monoxide, carbon dioxide, oxide of nitrogen, and hydrocarbons in the underground environment. Miners who are exposed to this kind of emission are at high risk for developing lung cancer and other lung diseases. The Mine Safety and Health Administration (MSHA) has issued standard rules to regulate diesel emissions in underground mines. The final ruling confirmed in 2008 that the total carbon should not exceed 160 µg/m3. (MISHA, 2008) Monitoring DPM in underground mines has become important to ensure compliance with the MSHA regulations. There are many different types of DPM monitoring systems that are currently being used in underground mines. Two methods are typically used for DPM sampling: the personal sampling method or the direct exhaust sampling method, which takes a direct sample from the engine’s tailpipe. Many mines do not recommend using the direct exhaust sampling method since it involves complex measuring equipment and procedures, as well as it is not regulated in the United States or Canada. Thus, the personal sampling method is the preferred method in many mines when taking DPM samples. Even this method includes many variations, such as the Respirable Combustible Dust (RCD) method and the method devolved by the National Institute for Occupational Health and Safety NIOSH 5040. The NIOSH 5040 method is the preferred method overall because it gives more accurate measurements compared to the other methods. This method does not allow organic carbon sources other than those coming from diesel engine exhausts to interfere with the measurements, which otherwise would lead to overestimating the actual amount of the DPM in the mine environment. An impactor feature in the cassette, which holds the samples in the instrument, characterizes this method. Since the diesel particles are less than 0.9 micron, this impactor does not allow particles more than 0.9 microns to be collected in the cassette filter. The cassette is then analyzed in a lab and the concentrations of organic carbon (OC), elemental carbon (EC), and total carbon (TC) are determined. Lately, the National Institute for Occupational Safety and Health (NIOSH) has developed a new instrument that can use the same concept of NIOSH 5040, but with instant measurements of elemental carbon. It utilizes laser radiation with the cassette so it can give a real time measurement. The real time measurements give instant information about the underground environment that will allow the mining engineer to take immediate action and enact plans instead of waiting for results from the laboratories where NIOSH 5040 method may take several weeks to get the measurements."

Jan 1, 2016

By A. Bleier, E. D. Goddard, R. D. Kulkarni

The influence of the collector structure on the amine (RNH2, R=alkyl) flotation of quartz has been systematically investigated using a modified Hallimond microflotation cell. This study focuses on the effect of varying chain length, branching in the alkyl group R, polyfunctionality of the collector molecule, and alkyl substitution on the nitrogen atom. In addition, adsorption at the solution/air interface and electrokinetic results for the solid/solution interface were employed to further elucidate the role and the interrelation of the structural parameters in the flotation process. Estimates of an electrical double layer attractive energy between the bubble and the solid particle are made.

Jan 1, 1976

By Clark B. Risler

Conveyors constitute a critical artery, essential to the successful operation of most ore processing plants. Technological progress is permitting the recovery of metal from low grade ores which previously could not be worked economically. Significant in this progress are improved material handling techniques highlighted by the frequent and successful application of conveyors. From the standpoint of the plant manager the successful conveyors are those he never hears about. They continue to economically transport the loads applied to them, requiring only routine maintenance attention. When such conveyors are subjected to closer scrutiny you will find that they have been carefully selected and engineered to perform the required function under the anticipated conditions. Among the primary elements in a conveyor drive are the electrical motor and the speed reducer. The selection of these elements can be aided by the systematic consideration of several factors. These factors which focus attention on the critical operating conditions, will be individually evaluated and their effect upon the selection of the electrical drive system and speed reducer analyzed.

Jan 1, 1958

By J. J. Crowhurst

The Carson Hill mine in Calaveras County, California, was explored and developed by Grandview Resources Inc., as an open-pit heap-leached operation, with production commencing in the fall of 1986. Grandview entered the district in 1983 after a 40-year period of quiescense, the initial contact being by Barden Stevenot, V.F. Hollister, and J.J. Crowhurst. The last dividend declared by the Carson Hill Gold Mining Corp. was 3 1/2$ per share paid in January 1943. The mine was originally discovered in August 1848 by Jim Carson. Preceding the entry by Grandview in 1983, Cyprus Mines explored Carson Hill in 1975, and drill exposed a mineral inventory of 7.3 Mt (7,982,000 tons) averaging 1.4 g/t (0.040 oz per ton) gold. From that time until the Grandview entry, R.W. Thomssen and B.E. Stevenot continued investigations into the potential of the deposit. Grandview successfully investigated many of the metallurgical problems involved with heap leaching the ore. Metallurgical investigations were con- cluded under the direction of R.S. Shoemaker. By November 1984, J.A.C. Ross had prepared a prefeasibility report that included the earliest Grandview investigations. This report concluded that the deposit contained at least 6.8 Mt (7,440,000 tons) of ore that average 1.5 g/t (0.045 oz per ton) gold and that this ore could be mined with a 2: 1 stripping ratio. A final feasibility report was prepared by D.W. Pringle in September 1985. It showed a final ore reserve of 14.7 Mt (16,160,000 tons) of 1.7 g/t (0.049 oz per ton) gold. Attached is a description of the geology of the deposit from an internal report covering Cyprus activity in 1975 and a brief portion of USBM IC 6940 (1937). General location and geologic maps attached are from the Pringle report.

Jan 1, 1990

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997

By Samuel S. Adams

The Grants uranium region of northwest New Mexico is the largest uranium district in the United States (approximately 50% of U.S. production plus reserves) and one of the largest In the world, with approximately 900 million pounds U308 production plus reserves. Deposits of the region are unusual among sandstone deposits for their high content of epigenetic carbonaceous material, generally interpreted but not proved to be of humic origin--that is, co-extensive with uranium in the primary deposits. Virtually all production in the region has been from the Jackpile Sandstone and Westwater Canyon Member of the Jurassic Morrison Formation. The tabular uranium deposits contain, in addition to humate and uranium, significant authigenic phyllosilicates, quartz overgrowths, humate-replaced detrital silicates, and a trace-metal assemblage typical of other sandstone uranium deposit types. Surrounding the deposits in the two sandstone units of the Morrison Formation is an alteration zone within which iron leaching has altered detrital ilmenite-magnetite to residual masses of titanium oxides. Feldspar alteration is locally present within this zone, below deposits in the Jackpile Sandstone, and above those in the Westwater Canyon Member. The feldspar alteration increases in inten¬sity toward the Brushy Basin Member which separates the two sandstone units, ranging from partial replacement to replacement and dissolution of plagioclase and sanidine. Spatial relations among the epigenetic humate, authigenic silicates, and the broad alteration zones that extend from the Brushy Basin Member to and including the uranium deposits suggest that (a) the organic material was involved in the unusual silicate alteration, transport, and authigenesis, and (b) that the humates originated in shales of the Brushy Basin Member. Stratigraphic relations among the Brushy Basin Member and the overlying Jackpile Sandstone and underlying Westwater Canyon Member suggest [in turn] that there was continuous, interfingering deposition controlled in part by contemporaneous basement subsidence along northwest- and northeast-trending zones. Following minor erosion of upper Jackpile Sandstone and deposition of basal organic-rich Cretaceous sediments, the silicates of the Jackpile Sandstone were once again altered by organic-bearing fluids, this time permeating down from Cretaceous sediments and partly obliterated ore-stage alteration.

Jan 1, 2013

By J. S. Y. Wang, R. C. Trautz

To evaluate the potential for water seeping into an underground opening, a 9-m- (30-ft-) long drift was constructed in the unsaturated fractured tuff at Yucca Mountain. Forty seepage tests were performed by releasing finite volumes of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2002

By C. Huang, S. Lin, Y. J. Wang

Introduction A mine characteristic curve is of great importance for both theoretical analysis and daily management of a mine ventilation network. Ventilation engineers are well acquainted with the ways of obtaining and using a mine characteristic curve that is conventionally associated only with single-fan networks. However, for a multiple-fan network, difficulty has long been recognized in defining the curve, not to mention, obtaining or using it. To extend the concept of mine characteristic curves for a multiple-fan network, a subsystem-based approach has been introduced by Wang (1992a). He defines a subsystem characteristic curve for a multiple-fan network and discusses the numerical procedure for constructing the curve. A graphical method of obtaining a subsystem characteristic curve for serial-parallel, multiple-fan networks has also been accomplished (Wang, 1992b). In spite of the maturity of the fundamental concepts related to and the numerical analysis tool for a multiple-fan ventilation network, information regarding the related laboratory tests is very scarce. To make up this gap, laboratory experiments have been done by using a two-fan experimental network. This paper presents the methodology and major findings regarding the construction and features of a subsystem characteristic curve. Characteristic curves and measurement fundamentals A characteristic curve A characteristic curve is a graphic presentation of the relationship between any two variables of a two-terminal component. It is typically defined in the form of a quantity-pressure curve for a ventilation component, which can be a single branch (airway), a fan, a regulator, a portion of a network or even a whole network. If a component is a single branch, the curve is called a branch characteristic curve. If it is a fan, then the curve is called a fan characteristic curve, and so on. Figure I illustrates the characteristic curves of some typical ventilation components. A general method for obtaining a characteristic curve from measurement is to apply an adjustable-pressure source between the two terminals of a component and measure the quantities corresponding to the different pressures. Mine characteristic curve A single-fan network can be easily divided into two ventilation components, the fan and the remaining network. The latter consists of only branches and regulators. Under this subdivision scheme, two characteristic curves can be constructed. They are the fan characteristic curve and the characteristic curve of the remaining network. The latter is referred to as the mine characteristic curve or the system characteristic curve. Although the general method for constructing a characteristic curve from measurement can be applied to obtain a mine characteristic curve, there is a shortcut for constructing the curve by introducing a mine resistance factor R. It is a constant if all of the resistance factors in the network are constant. R relates mine pressure H with quantity Q as in: H=RQ2 (1) For a given R, Eq. (1) can be directly used to plot a mine characteristic curve by assigning a series of Q values and calculating the corresponding H values. Hence a shortcut to constructing a mine characteristic curve is to measure one set of mine pressure H and quantity Q values, calculate the mine resistance factor R using Eq. (1) and then plot the curve. Subsystem characteristic curve Applying a similar scheme as is used for a single-fan system, divide a multiple-fan network into two components, a fan under consideration and the remaining network that contains all the other elements (branches, regulators and remaining fans) of the network. The fan under consideration

Jan 1, 1994

By R. Schlüter

"The global mining industry is facing increasing challenges in terms of geological, technological and social aspects. Potential exploi-tation of deposits shows a tendency to increasing depth with complex ores and decreasing grades. A promising approach to deal with these constrains is by applying alternative extraction methods like (bio-)hydrometallurgy as in-situ leaching (ISL) technology. The Bergakademie Freiberg University of Mining and Technology established the “Biohydrometallurgical Center for strategic Elements” (BHMZ) to foster the interdisciplinary research along the entire biohy-drometallurgical process chain to extract indium from sulfide ores. The involved Department of Underground Mining Methods deals with the design and implementation of a pilot-scale underground testing facility for microbial in-situ stope leaching in its “Research and Educational Mine”. This paper discusses the potential of in-situ bioleaching under technological aspects. In addition, different conditioning approaches based on hydraulic and explosive methods for enhanced permeability in the formation are introduced and the gathered data will be presened. INTRODUCTION A reliable, substantial and sustainable supply of raw materials is of crucial importance for any industrialized country. This dependency applies to “strategic elements” including rare earth elements (REEs), platinum group metals (PGMs) as well as a variety of other metals like indium and germanium which are needed for high-tech industry and products such as electric and electronic devices, fibre optics and laser technology (Barakos et al., 2016; European Commission, 2010). Due to the economic growth of the BRIC-countries (Brazil, Russia, India, China), the resource policy of China as well as the volatile world mar-ket prices of different metals the availability of these critical raw materi-als and therefore the dependency of the high-tech producing countries has become increasingly important (Barakos et al, 2016). Adequate supply is often affected by the increasing depth of de-posits, lower metal concentrations and more complex ore mineralogy. In addition, mining activities are increasingly restricted by their envi-ronmental and social impact and footprints. As a consequence, con-ventional mining and processing methods are limited by high energy consumption and technical constraints."

Jan 1, 2018

By C. G. Cunningham

The Marysvale volcanic field of west-central Utah contains large areas of argillically altered rocks (fig. 1) that, in turn, enclose smaller areas of fine-grained, medium-grade, replacement alunite deposits and coarsely crystalline, high-grade vein-type alunite deposits. The largest replacement alunite deposits are [ ] located peripheral to a 23-m.y.-old monzonite stock called the Central Intrusive (fig. 1). The deposits formed in near-surface, highly oxidizing environments at the tops of hydrothermal plumes that were spaced irregularly around the stock. The deposits are horizontally zoned from alunitic cores through kaolinitic to propylitic envelopes. Vertically, characteristic alteration minerals progress from a pyrite-propylitic alteration assemblage at the base, upward through alunitic, jarositic, and hematitic assemblages to a flooded silica cap as shown on figure 2. The silica caps are cut by hydrothermal explosion breccias. d34Sso4 values of + 11.5 to + 15.4 permil indicate that sulfur in the hydrothermal plume was derived from underlying Mesozoic evaporites. The sharp upward transition from pyrite- propylite to alunite probably marks the paleowater table, and the top of the flooded silica cap represents the paleoground surface. Basin-Range extensional tectonism began shortly after alteration, and buried the replacement alunite deposits in basins beneath sediments eroded from uplands. The deposits were only recently exhumed.

Jan 1, 2013

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958