Search Documents

By S. Y. B. Subbarao, K. Ravindranath

Lead and Zinc concentrates are being recovered at Rajpura- Dariba (Distt. Rajsamand, Rajasthan, India) from a complex multi metal sulphide deposit since 1984 by selective flotation employing a large number of reagents. The cost of concentrates' production has been high. Due to the increased availability of concentrates world over and to be competitive, it is necessary to reduce cost of production. An effort has been made by the R.D. Department of Hindustan Zinc Limited to bring down the cost by resorting to production of Bulk Pb + Zn concentrate with enough Ag to make it attractive to the smelters. This paper gives an account of open cycle testing and locked cycle testing in the Dowa Continous Mini Flotation unit. The metallurgical data generated in the mini flotation unit indicate the possibility of obtaining smelter-acceptable bulk concentrates containing Pb+Zn 45%, Ag 400 ppm and graphite carbon about 3%. An in-plant trial in the 3000 TPD concentrator indicated that there would be savings through dispensing with and reduction in some reagents, lower power requirement, etc. Also, a substantial increase in revenue is expected due to higher recoveries by resorting to bulk concentrate production as against individual concentrates.

Jan 1, 1995

By J. M. Mutmansky, Y. J. Wang

The method usually used to predict the direction of flow in a connecting airway is to conduct a survey of the two existing nodes to be connected by the new pressure airway. It is then assumed that the air will flow from the node with the measured higher pressure to the node with measured lower pressure. This paper examines this direction-of-flow problem using properties of the system characteristic curve for a two-terminal network and specifies some conditions that will ensure that the air will flow in the direction anticipated. It was concluded that the only requirement is that all characteristic curves of the fans in the network should be strictly decreasing. Five numerical examples illustrate some important proper- ties of the direction-of-flow problem.

Jan 1, 2000

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease with increasing volume, while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. However, as every ventilation instructor knows, the fact that head loss is a negative number (debit) and fan head is an energy addition (credit) is often a stumbling block to student or audience comprehension since the curves seem to reflect the opposite. It is possible to use the intuitively correct curves- pressure losses as negative values and energy additions as positive values - and still obtain the correct operating point. Adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure. With the standard approach, it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1999

By J. A. Herbst, Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comminution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5x6.4-m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790:1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By Dragomir Gospodinov, Savka Dineva

A surprisingly large mining-induced seismic event occurred in the LKAB Kiirunavaara Mine (Sweden) on 18 May, 2020 at 03:11 (local time). The estimated moment magnitude was 4.2. The event caused extensive damage in a large section of the mine. The production in the area is not yet resumed, even by the beginning of 2022 (~20 months after the event). The Kiirunavaara Mine has one of the world’s largest underground seismic systems with approximately 253 geophones. The in-mine records of the event showed a very complex character with a several sub-events. The event was also well recorded by seismic stations out to over 9,000 km distance. Data from the underground and regional seismic systems were analysed to define and compare basic source parameters such as hypocenter location, seismic moment, as well as the seismic moment tensor. The data from the in-mine seismic system was used to study the development of the seismic process and to define elementary seismic sub-sources together with the official hypocenter location.

Apr 26, 2022

By S. S. Peng

Since the introduction of shield supports in 1975, safety and production in U.S. longwall faces have improved considerably. Many faces had a daily production of up to 8,000-10,000 tons and productivity reached 600 tons per man-shift. But a longwall face requires expensive equipment which slows down the growth rate of the percentage of longwall production. Among the equipment cost the shield support accounts for 50-60%, a very large proportion. Therefore, it will have a large impact on the growth of longwall mining in the U.S. to reduce the support cost (1).

Jan 1, 1988

By V. Králová

The TESCAN Integrated Mineral Analyzer (TIMA), an automated mineralogy system, enables fast and quantitative mineral analyses of rocks, ores, concentrates, tailings, leach residues or smelter products. It combines BSE and EDX analysis for identification and measurement of mineral concentrations, particle size distribution, and liberation/locking parameters. In addition, it can provide bright particle searches for PGM, gold-silver ores, and/or REE. With the newly developed Automated Loading System (AutoLoader), the TIMA has become the world?s first automated mineral analyzer which permits robust, continuous and unattended sample loading. With the AutoLoader (robotics) system, the TIMA has emerged as a powerful plant support instrument. It increases the sample throughput, minimizes manual labor and enables 24/7 operations. As such, it can be used in daily, continuous mineralogy for mine geology/ore control, concentrators, leach operations, and smelter support. It will also increase the capabilities of technical service centers for mining companies, commercial laboratories, large drilling programs or pilot test campaigns. In combination with a highly automated sample preparation lab (sizing, potting and polishing), TIMA technology can establish high-throughput and fast-turnaround automated mineralogy lab modules for mine-site production support.

Feb 23, 2014

The 2012 North American Tunneling (NAT) conference is expected to attract more than 800 tunneling and underground construction professionals. But don?t let the North American part of the meeting?s title fool you. Many of the attendees will come from all over the world. The meeting is scheduled for June 24-27 at the JW Marriott Indianapolis Hotel in Indianapolis, IN. In addition to two and a half days of technical programming, the accompanying exhibit has attracted 116 exhibitors in 140 booths. And the conference will include short courses, a field trip and plenty of social activities that will give attendees the opportunity to catch up with each other.

Jan 1, 2012

By J. Tavares

It is no mystery why the mining industry has such lofty safety standards. In dealing with Mother Nature and gravity, the combination of the two can create significant hazards from high wall and tunnel collapses to huge landslides. The loss of production from a major disruption could be enormous. The price tag on the loss of human life is immeasurable. The evolution of geotechnical instruments and software has been ongoing for years. But the biggest innovations have occurred during the era of cell modems, internet, and wireless networks, allowing for real time data and alarms to be delivered globally anywhere and anytime to one?s computer, laptop and smartphone. Yet in some ways you can thank the urban construction projects for developing much of the technology in use by today?s mines. Due to the density of population and the billions in dollars of structures and infrastructure in cities throughout the US and the world, urban projects have faced intense scrutiny for years. Out of this scrutiny was born the necessity of real time automated monitoring of instrumentation and sensors, a defence against catastrophic failures, and real time early warning systems through alarms that can and do saves lives. It is also possible to identify areas of concern with subsequent remediation prior to failure.

Feb 23, 2014

By A. W. Laughlin

Analytical costs are a major part of exploration programs in developing nations which may lack adequate laboratories. Laser-Induced Breakdown Spectroscopy (LIBS), a variant of atomic emission spectroscopy, can reduce exploration analytical costs and can provide the analytical results in <1 minute. CPI is now marketing battery-powered, backpack mounted analyzers, using LIBS to analyze for many elements of interest to the explorationist. LIBS is well suited to the analysis of elements in industrial minerals. Limits of detection in ppm for some of these are: Li-1, Be-2, Na-100, B-33, Sr-10, Ba-300, Cs-1, K-500, Fe-500, Mg-500, and Ti-500.

Jan 1, 1999

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By Bo-Hyun Kim, Mark K. Larson

"Bumps remain a critical safety concern in underground coal mining, despite significant advancements in engineering controls. These events occur when relatively high stresses in a coal pillar in conjunction with low confinement exceed the pillar’s critical capacity, causing the pillar to rupture without warning. Floor failure often occurs and can be an indicator of bump risk, as it is strongly associated with brittle failure known as spalling under a lower confinement. Significant floor heave at a western U.S. coal mine has been observed where the pillar width in a three-entry gate road system was 53 m, while no significant floor heave was observed where the pillar width in another gate road system was 22 m. This phenomenon was widely reported in the region and at another mine in another western coal field it has been reported that larger pillars are always associated with floor heave. In this study, a spalling model based on the S-Shaped brittle failure criterion and associated with the anisotropic characteristics of the materials was used in FLAC3D. The observed floor heave phenomenon associated with the larger pillars was demonstrated using this modeling approach.INTRODUCTIONFloor failure in a coal mines often inhibits longwall mining operation, as large displacement of floor strata, known as floor heave, interferes with travel, access, ventilation, and equipment operation. Aggson (USBM 1978) investigated floor heave in West Virginia where underclay is relatively strong and high horizontal stress is present. It was reported that the failure mode is mainly by buckling rather than by plastic flow.This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock mass behavior in longwall coal mines in highly stressed, bump-prone ground. More specifically, this study attempts to explain through numerical models small energy releases in the form of floor heave. The authors believe that brittle rock failure is associated with both floor heave and some bump mechanisms, if not directly involved in their cause."

Jan 1, 2019

By Jon Y. Kaneshiro, Donald W. Scapuzzi

The primary purpose of the Prototype Installation Facility (PIF) for the Superconducting Super Collider (SSC) in this conceptual design was to test the magnets and other physics equipment. PIF was located in the northwest quadrant of the SSC 54 mile (87 km) main ring and consists of the first segment of tunnels, approximately 17,060 lineal feet (5.2 km) of 12 foot inner-diameter (ID) (3.7 m) tunnel, three 250 ± foot (60 m) deep shafts, connecting tunnels, and associated niches and alcoves. PIF would be the first portion of the main ring collider tunnel to be constructed. The geology, underground excavation conditions, underground facilities, and contractual considerations are discussed.

Jan 1, 1991

By James Y. Oldshue, Paul M. Kubera

Ore processing requirements in the gold industry are similar to those in other sectors of the minerals industry. In all cases, the processes revolve around the handling of large volumes of ore slurry, incorporating either physical processing or chemical processing steps which are related to distinct mixing application classes as defined in Table 1. From this standpoint, the complexity of the applications range from the simple (blending, solid suspension, etc.) to the complex (e.g., multi-phase reactor systems). The large volume of material to be processed dictates the large equipment size which is characteristic of this industry, and the often remote locations place a premium on both mechanical and process reliability.

Jan 1, 1992

By James Y. Oldshue, Paul M. Kubera

Most coillillercial processing applications employing mixers in various types of slurry systems are continuous flow. These applications may also be multiple stage, with the stage number varying anywhere from two or three to ten or more. Two questions that usually come up at the beginning of any proposed pilot plant study are (1) can the pilot plant unit be operated batch-wise, and the results extrapolated both on the basis of scale and fluid motion to the full-scale tank which will be continuous-flow (and probably multi-stage), or (2) does the pilot plant need to be operated in a continuous-flow fashion, and if so, does the exact number of tanks/stages that are proposed for the plant need to be used in the pilot plant? We will consider these possibilities in sequence and present the principles involved in running some of the various pilot-plant arrangements.

Jan 1, 1992

By R. Mensah-Biney

The loading characteristics of gold-tetrabromide species onto activated carbon have been evaluated using a completely mixed batch reactor system. The overall loading of gold onto carbon was rapid for the first hour but continued slowly without cessation as a result of reduction of gold. Conventional equilibrium considerations were therefore not applicable. Although loading continued slowly after several days, abnormally high loading capacity values of 10-12 meq/g carbon (650-800 kgAu/tonne) could be attained within 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of [AuBr4l-onto the carbon surface where reduction to metallic gold took place. Elution of gold from the loaded carbon was feasible provided the carbon had not been loaded to too high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon is discussed.

Jan 1, 1992

By I. K. Gilmore

Texasgulf Inc. currently operates an open pit phosphate mine in the central coastal plain of North Carolina. The area of phosphate deposition lies within the Aurora Phosphate district which consists of an embayment which is in the center of the Neogene phosphate deposition. A variety of solid and liquid fertilizer products are produced at the Texasgulf complex. One of these products is known as North Carolina Natural Phosphate (NCNP). New potential for use of unacidulated natural phosphate, now exists in regions with acid soils due to the discovery of the findings from recent research, cost advantages, and moves to reduce chemical inputs.

Jan 1, 1995

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. To develop the model of the ventilation system with the fire in this validation study, the following adjustments were made: (1) flow and gas distribution in the entire ventilation network, and (2) fire parameters matching the data recorded by the monitoring system. After close correlations between simulation and real data were achieved, additional analysis of the ventilation system with the mine fire was performed. Presented and discussed in this paper are the following stages of the fire at the Pattiki Mine: (1) early fire (before the fire was detected), (2) preparation for and fire fighting with water, (3) fire sealing, and (4) fire extinguishing. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable dust samples from underground coal mines is the P-7 method, a combination of low temperature radio-frequency ashing (LTA) and infrared analysis (lR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive Infrared (IR), Fourier-transform Infrared (FTIR), and X-Ray Diffraction (XRD) methods are most commonly used for quartz analysis in powders. Several aspects of the experimental procedures such as the analysis sample preparation from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist, and data interpretation affect differently the results from each of the methods. Significant differences in analysis results from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All these studies point to the need for reliable quartz analysis methods. In a recent research, a procedure for preparing bulk coal and host rock samples for quantitative quartz analysis was developed. Further the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle size distribution, matrix, and calibration on analysis results. In this paper, several issues with the measurement of quartz in the samples of coal, host rock, and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1994

By A.M. Wala

A new radioactive tracer method to measure airflow in inaccessible airways has been developed for situations when studies of the mine ventilation system are not possible using conventional flowmeters (anemometers). The new method has been tested in the ventilation laboratory at the University of Kentucky and in the Experimental Underground Coal Mine at the U.S. Bureau of Mines. This new tracer method has been utilized in leakage, dilution and flow velocity measurements in laboratory and field (mine) experiments.

Jan 1, 1996