Search Documents

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By M. A. Trevits

Methane gas is an ever-present problem facing the underground coal mining industry. Mine operators are mandated by law to maintain safe concentrations of methane gas within the mine environment. Ventilation is used by all mine operators to reduce gas concentrations. When gas emissions are such that ventilation alone cannot control the gas, methane drainage methods must be applied. In the 1970's, there was a concern that unprecedented gas emissions would be experienced as mine operators began new developments in the deep and gassy Blue Creek and Pocahontas No. 3 Coalbeds. Such concern was well founded as significant gas volumes are being emitted as these mining operations mature. In 1971, the O.S. Bureau of Mines began to tabulate and track the change in mine emissions. These data were extracted from the underground coal mine quarterly air quality-quantity inspections performed by the Mine Safety and Health Administration. At that time, approximately 6,560 Mm Id (231.7 MMcfd) of gas were emitted from 430 underground coal mines. It was determined however, that the mines emitting less than 2,832 m Id (100 Mcfd) contributed only 2.1 percent of the total daily gas flow. In 1988, underground coal mines emitted 8350 Mm Id (294.9 MMcfd) from 487 mines. This report evaluates the changing nature of U.S. mine gas emissions over the last 18 years.

Jan 1, 1993

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa's electricity using coal fired power stations,

Jan 1, 1990

By I. B. Tulu, M. M. Sears

"In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial, yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground fall related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground fall related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 21 longwall mines were visited, representing about 40% of the currently active longwall mines in 4 of the 5 major US longwall producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. The results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries. INTRODUCTION Maintaining ground stability in gateroad entries is essential for longwall productivity and safety (Campoli, 2015). In 2015, 148 unintentional roof falls were reported in US longwall mines. About 34% of these resulted in mineworker injuries. Safety considerations not only include injury from roof and rib falls but also egress from the longwall face during an emergency (Mucho et al., 1999). Over the past 30 years, a number of researchers have studied longwall tailgate support performance (Mirabile, 2015). This research aims to take a snapshot of the ground support installed in modern US longwall mines and provide a supplement and update to the overview provided by Barczak (2005). This will provide a framework for future research into improving gateroad support systems. BACKGROUND Large unplanned roof falls at or above the primary support or those impeding travel and/or ventilation must be reported to the Mine Safety and Health Administration (MSHA). Reportable roof falls, normalized based on production in million metric tons, generally relate to the amount of roof exposed during the mining process (Pappas and Mark, 2012) and provide an evidence-based statistical background for this review of current support practices. Figure 1 shows the reportable roof fall rate in US underground longwall mines for the period 2006-2015 (MSHA, 2016). Over the past decade, roof fall rates have shown a gradual decrease with numbers now at a rate nearly half of what was observed just five years ago. However, over the past few years, roof fall rates in US longwall mines appear to have stagnated at levels just over 1 per 2,000,000 tonnes mined."

Jan 1, 2017

By David Beck, Eko Wibowo, Hendri Silaen, Andres Sugiyanto, Karl Llewelyn

PT Freeport Indonesia’s Deep Mill Level Zone mine is one of the deepest block cave mines in the world and is in mountainous terrain in West Papua, Indonesia. The mineralization is hosted in a skarn deposit in a structural setting that is complex at the footprint, mine and regional scale. Large seismic events and significant episodes of rapid rock mass deformation are potentially critical geotechnical risks during this ramp-up stage of mining. Understanding the interaction between stress, strain, rock mass strength and geological structures is essential to minimize the hazard and engineer control measures to help ensure the safety of the employees while achieving production targets. This paper discusses how the seismicity and excavation damage have been shaped by the interactions between the mine and geological features, and how this affects strategic mining decisions. Additionally, the paper presents a summary of the mitigation measures used for mining the DMLZ in the safest and most productive way. These include improvements to geotechnical characterization of rock mass and structure, dynamic ground support designs, production scheduling for desirable cave propagation and a seismic monitoring system with re-entry protocols.

Apr 26, 2022

Last year in the US alone, about 425 Mt (468 million st) of minerals and coal were beneficiated by froth flotation. This number indicates that from 1983 there was a 10% increase in tonnage of min¬erals and coal beneficiated by the indus¬try. A significant improvement was seen in the tonnage processed by the nonferrous minerals and coal industries. BP Minerals America installed 85 m; (3000 cu ft) flotation cells at the Bing¬ham Canyon mine and concentrator. The new flotation circuit has fewer than 100 cells compared to 2000 flotation cells used in the old plant (Mining Engi¬neering, November 1988). Column flotation use on a commer¬cial scale continues to expand as seen from the interest expressed at the Col¬umn Flotation Symposium (Column Flotation '88). The Magma Copper Co., San Manuel Division replaced all con¬ventional cells with 1.8 x 12 m (6 x 40 ft) column flotation cells for copper con¬centrate cleaning. Also, 1220 mm and 760 mm-diam (48 in. and 30 in.-diam) column cells are operating at the plant in the molybdenum circuit. A commercial Diester Flotaire col¬umn cell for fine coal recovery was installed at the United Coal Wellmore No. 20 plant. The 36.8 m3 (1300 cu ft) cell recovers 13.6 to 18 t/h (15 to 20 stph) of -590 gm (-28 mesh) coal. A similar unit has been installed at Tanoma Mining Co. in Pennsylvania. Various modifications of the column cells are being designed around the world. Jameson (Mining and Metal¬lurgy, 1988) described a new concept whereby the feed and air stream mixture is discharged into a cylindrical column of about 1.2 m (4 ft) height. Recovery and grade of nonferrous minerals have been reported to be better than that in a four-stage conventional flotation clean¬ing circuit. Flotation reagents American Cyanamid and Dow Chemical continued development of a new generation of sulfide collectors. A general feeling is development of new sulfide collectors has not kept up with flotation technology. Additionally, joint efforts between industry and chemical suppliers will likely be necessary to realize the economic benefits of the new technologies, since new chemistries respond differently compared to the conventional collectors. Flocculant development in recent years has been evolutionary rather than revolutionary. Rothenborg reported on development of a new flocculant family (a hydroxymated polyacrylamide desig¬nated S-6703) that has shown consider¬able promise in red mud clarification. Plant testing showed that this new floc¬culant could replace starch and poly¬acrylate and provide significantly higher overflow clarity. Barol Kami (Siirak) and Cleveland¬Cliffs (Hancock) reported development of an amphoteric apatite collector (ATRAC 873) that was used in Tilden's silica flotation process to increase apatite rejection. The collector was engineered for the particular flotation conditions in the complex Tilden process. Significant plant testing with ATRAC 873 showed that this reagent gave significantly in¬creased apatite rejection without any effect on silica flotation effectiveness or selectivity. Electrostatic separation Electrostatic separation is now em¬ployed in the precious metals mining industry to recover gold and silver grills from crushed slag. The installation at Paradise Peak has prompted other op¬erators to consider this application. In another development, attractive potentials for treating very fine minerals (-45 µm or -325 mesh) are being devel¬oped by Advanced Energy Dynamics and by the Department of Energy. Demonstration tests using triboelectric charging/electrostatic separation have been successful on a variety of minerals as well as coal. Magnetic separation Developments in magnetic separa¬tion have transpired on a production scale. Superconducting, high gradient magnetic separation has gained accep¬tance with the successful startup of a second unit treating kaolin at J.M. Huber Corp. This liquid-helium-cooled mag¬net generates 2.0 tesla in a 3-m-diam (120-in.-diam) bore with no power con¬sumption. Wet, high-intensity magnetic separation has been applied to sulfide mineral separations both domestically and abroad. These continuous type of separators are effective in removing residual chalcopyrite and sphalerite from other base metal sulfide concentrates. Separators using high energy rare earth permanent magnets are continu¬ally increasing. Now offered as both drum and roll type, these units are be¬coming a staple in the processing of industrial minerals. Tests using rare earth magnets strategically placed on a spiral concentrator have demonstrated the enhanced recovery of heavy miner¬als such as ilmenite. Classification Although no major technology break¬throughs in classification appear immi¬nent, there is an increasing need for more efficient and cost-effective meth¬ods to make size separations. It is be¬coming more apparent that mineral concentration methods will be more common at very fine sizes, say below 50

Jan 1, 1989

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By Michael J. Beus

This paper describes research conducted under the BuMines's Advancing Metal and Nonmetal Mining Technology Program, a major element being the application of new and improved technology to shaft design in deep underground vein-type mines. Two basic design parameters considered in shaft planning are configuration (shape) and ground support. The most common shapes are circular and rectangular. Ground support systems include concrete, timber sets, steel sets, rock bolts, and steel liners. The inherent advantages and/or disadvantages of various shaft designs such as ventilation and fire resistance, flexibility and ground support characteristics are well known. Circular concrete-lined shafts have minimal resistance to air flora and are virtually fireproof, an important consideration in deep hot mines. However, concrete does not yield significantly, and failure conditions and misalignment cannot be easily repaired. Timber-supported rectangular shafts predominate in the Coons d'Alene Mining District with its highly stressed and frequently heavy ground. The sets can be relieved and reblocked when out of alignment. However, the constant maintenance and repair requirements result in exposure to an inherently dangerous working environment combined with excessive operating costs. Obviously a dilemma exists--a circular, concrete-lined opening has many desirable features, provided it is strong enough to withstand the stresses involved. Rectangular, timber supported shafts have proven adequate in the Coeur d'Alenes; however, the implication of increased maintenance and repair requirements on ever-deepening shafts in this district and other similar areas will be an important design consideration in the future. This paper, then, presents shaft-configuration and ground-support guidelines to help remove some of the uncertainty concerning the stresses to be encountered in typical deep vein mining areas.

Jan 1, 1976

By Warren D. MacEvoy

INTRODUCTION Good ventilation bulkheads (stoppings) can be obtained only by conscientiously adhering to four basic principles: carefully selecting the site for the bulkhead, adequately preparing the site, properly constructing and sealing the bulkhead, and checking the results with a smoke tube before leaving the area. If all these guidelines are followed during each ventilation project, a poor job will result only from the use of improper materials and cannot be blamed on carelessness or oversight. SITE SELECTION A perfectly constructed bulkhead in the wrong location can be completely worthless. Conceivably, a bulk-head in the wrong location could cause dangerous ventilation conditions that are difficult to identify and isolate. If the suggestions herein are followed, a considerable amount of work, time, and material may be saved. Perhaps the single most important step is always to select the exact site for a bulkhead before starting construction. Although the latitude in selecting a site may be limited by instructions or operating conditions, it is common to find poor bulkheads built within a few meters (feet) of a site that would have been far superior but was overlooked during the planning process. The ideal site for a bulkhead should have as many of the following features and conditions as possible: 1) To provide a solid bulkhead, the selected site should be in firm and unbroken ground. 2) To minimize the amount of work and material required and to minimize the danger of later damage to the bulkhead, the site should have as small a cross section as possible. 3) The bulkhead site should not be encumbered by interferences such as pipes, wires, ditches, wire roof supports, trash, muck piles, etc. 4) The walls and timbers of the site should be free from oil, grease, or tar that would inhibit adhesion of the sealant used on the bulkhead. 5) Unless special precautions are taken, the site should not have water seepage, standing water on the floor, or water-carrying ditches. 6) To expedite construction of the bulkhead, the site should have reasonable access to transportation, supplies, communication facilities, and compressed-air lines. 7) The site should have a reasonably level floor, allowing direction of the bulkhead door swing to be reversed at a later time if so desired. In a steeply sloping location, it may be possible to open the door in one direction only. SITE PREPARATION Once a suitable site has been selected for the bulk¬head, it must be prepared properly. All site preparation work should be completed before starting any construction work on the stopping itself. Unfavorable site conditions can be identified during the course of thepreliminary site preparation, saving time, effort, and materials that otherwise might be wasted. The follow¬ing preparation steps help assure the construction of a good stopping: 1) If wire mesh has been used at the site, a strip 457 mm (18 in.) wide should be cut and removed from the walls and roof at the selected location. 2) The exposed strip of rock should be barred down thoroughly to provide a smooth surface. 3) All obstructing materials should be removed, including old timbers, pipes, rockbolts, wires, etc. If a conduit must cross the bulkhead area, it should be located or relocated away from the floor, walls, and roof to allow a 6.28-rad (360°) seal around the juncture between the conduit and the bulkhead structure. 4) All loose muck should be cleaned from the site and a trench about 152 mm (6 in.) deep should be dug from wall to wall in the floor. The trench must be wide enough to accommodate the entire bulkhead, including the posts. 5) The rock surfaces of the walls and roof should be cleaned with a wire brush to remove as much loose surface material as possible. Thorough cleaning promotes adhesion of the bulkhead sealant to the surfaces of the walls and roof, thus promoting an airtight seal. 6) It is quite difficult to seal landing mats that cross a bulkhead. If such a crossing cannot be avoided, the bulkhead should be placed between the end and the first hole in the steel so at least one side of the bulk-head can be sealed easily and completely. That may have to be done prior to actual construction if the end is located on the opposite face from the seal coating of the bulkhead. BULKHEAD CONSTRUCTION The three principal considerations in bulkhead con¬struction are the type of bulkhead, materials to be used, and construction method to be employed. For many projects, the bulkheads are specified by the requesting agency, with no latitude for independent choice of the type, materials, or construction method. In such cases, any deviations from the specifications, for any reason, must be approved in advance by the proper department or by the project senior ventilation engineer. Types and Materials When a choice of type, materials, or method is allowed, consideration should be given to factors such as cost, required useful life, proximity to blasting concus¬sions, availability of materials, direction of permissible air leakage, and degree of airtightness required. Other factors to be considered include the amount of time available, accessibility of transportation, potential for interference with operations or production, ambient water conditions, availability of connections to com¬pressed-air lines, etc. Despite the multitude of factors to be considered, most stoppings can be analyzed easily and the proper choices can be made without much difficulty. The four common classes of bulkheads utilized in

Jan 1, 1982

By David X. Zhang

This paper describes the results of using shear flocculation and flotation known as aggregative flotation technique for the enrichment of coal-derived char produced from mild gasification process. Aggregative flotation is a separation process which involves the use of suitable aggregating liquid under the action of high shear forces to render hydrophobic surface of coal-derived char particles to aggregate in an aqueous slurry. The fine carbonaceous particles are aggregated into larger floes while the impurities remain hydrophilic. In subsequent flotation process, the char aggregates are then separated from mineral matters by aeration in the flotation cell. The floatability of char aggregates and removal of mineral matters from chars are studied in a lab scale flotation column cell. The effect of various operating parameters on the aggregative flotation responses is presented. Emulsification of aggregating liquid using high intensity agitation and ultrasonic energy provides excellent aggregating liquid dispersion and increases selectivity for char aggregation. In subsequent flotation process, it results in significantly increasing the flotation rate of char aggregates. The microscopic examinations of bubble attachment to coal-derived char particles under various aggregating liquid dispersion levels were conducted by induction time measurement. The distributions of hydrophobicity of char particles and char aggregates prepared under various aggregating liquid dispersion techniques were measured by film flotation. The char particles prepared under high intensity emulsification attach at significantly faster rates to air bubble and with lower mean critical wetting surface tension than that of char with direct aggregating liquid addition. An interrelationship of increasing in flotation rate/combustible recovery with decreasing in induction time, mean critical wetting surface tension and dispersion of hydrophobicity on the char particles and char aggregates were obtained.

Jan 1, 1992

By H. Majima

In spite of the importance of the presence of pyrite in the flotation of sulphide ores, not many studies have been made from the electrochemical point of view. It is generally recognized that the oxidation of sulphide minerals is one of the most Important factors among those which affect the floatability of sulphide minerals. The concept that the presence of oxygen is essential to the flotation of sulphide minerals is supported by numerous experimental results (1). The presence of oxygen in sulphide minerals- aqueous solution systems would affect the electrochemical behaviour of sulphide minerals and subsequently lead to more complicated reactions on the surface of sulphides. Actually some of the phenomena observed in sulphide flotation are deemed to be more appropriately explained from the electrochemical point of view. The author and co-workers have studied extensively the electrode reactions of pyrite and its significance in sulphide flotation. The results have been partly published elsewhere (2-7). In this paper, the author discusses the electrochemical nature of pyrite, and the three different phenomena observed in pyrite flotation: (1) Xanthate¬dixanthogen system on pyrite, (2) Flotation of complex sulphide ores containing pyrite and (3) Depressive mechanisms of pyrite with cyanide. The phenomenon which has been known as an iron contamination effect due to steel grinding media on sulphide flotation is also explained from the electrochemical aspect. However, this problem is not directly concerned with pyrite, and it will be discussed elsewhere (8).

Jan 1, 1971

By E. M. Wilde

Through the USGS's National Coal Availability program, coal resource appraisals have been completed for three 7.5-minute quadrangles (Willow Crossing, Colstrip East, Colstrip SW) in the Powder River Basin area of southeastern Montana. Available coal reserves (original reserves minus tonnages affected by current restrictions) vary from 44 to 70 percent of the original reserves. Major restrictions impacting each area also vary. In each area, one or two beds contain most of the reserves, but up to eleven beds contain available coal. The main beds in completed studies are the Knobloch, Rosebud, Sawyer and Flowers-Goodale. Three additional areas (six 7.5-minute quadrangles) are in preparation.

Jan 1, 2001

By John J. Stetler

The Companhia Vale do Rio Doce in Brazil operates one of the most extensive systems in the world for the mining, transportation, processing, pelletizing and shipping of high grade hematite iron ore and pellets. Current shipping of unbeneficiated, sized, high grade ore from its ports at Tubarão and Vitória is now at the rate of 17,500,000 metric tons annually. An increase in this annual rate is now under study. Using the technology and facilities of Lurgi (1) and Arthur G. McKee company CVRD undertook a program to process and pelletize two types of fines - "Blue Dust" and ?Itabira Fines?. Blue Dust is a high grade fine ore which was bypassed while mining the direct shipping ores and which, also, exists as a very large ore body called the Conceição Mine. Itabira Fines is a lower grade of fine ore which is comprised of in-situ fines and, also fines which are generated in sizing the direct shipping ores for a rigid specification market.

Jan 1, 1970

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By T. F. Dumm

With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink-float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and sub-sieve particle size analysis of the specific gravity fractions, a complete size-specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.

Jan 1, 1987

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By A. S. Ibrado, D. W. Fuerstenau

"Gold, silver and copper form various complexes with cyanide, of which only the singly charged dicyano form adsorbs appreciably on activated carbon. The adsorption of the dicyano complexes appears to be controlled predominantly by chemical reaction at the surface of a shrinking unreacted core. Metal uptake over time is non-linear, which eliminates control by boundary layer diffusion. The rate of adsorption is not enhanced by a reaction interruption, which suggests the absence of concentration gradients in the pores. Finally, the rate of adsorption increases with decreasing activated carbon size in a manner consistent with the shrinking core model. The results of this investigation accentuate the importance of efficient acid washing of carbon and removing carbon fines from the barren carbon stream. INTRODUCTION With the dwindling reserves of high-grade ores, most of the world’s gold is produced from low-grade ores by cyanide leaching. In the past, leaching was followed by the Merrill-Crowe process, in which gold is precipitated from clarified pregnant solutions by zinc cementation. This process is still being used for high-silver ores, where the cost of carbon stripping becomes prohibitive. For deposits with silver-to-gold ratios of about 4 or less, adsorption on activated carbon would be the usual solution purification step taken. The process simplifies solid-liquid separation and offers a viable solution to preg-robbing organic carbon in some ores. The modern industrial application of carbon adsorption started with the carbon-in-pulp (CIP) process, where carbon adsorption was used mainly as a solution purification step. In 1973, Homestake Mining Company commissioned the first large-scale CIP plant in the U.S.A.1 Later, carbon was added earlier in the circuit to control preg-robbing by adsorbing gold cyanide onto activated carbon as soon as it is dissolved. The scheme is successful because activated carbon is a stronger adsorber than the organic carbon found in preg-robbing ores. This process came to be known as the carbon-in-leach (CIL) process. Numerous research investigations have been performed on the chemistry involved in the CIP process, which at the time of its introduction was not clearly understood. Of these, research on the kinetics of adsorption probably bears the most immediate impact on industrial practice,2,3 where adsorption systems rarely reach equilibrium, if at all, and slight slowdowns in the adsorption rate can translate into significant decreases in revenue. To illustrate this, organic compounds, like flotation reagents, have been known to impair CIP circuits. However, laboratory tests showed that the organic compounds do not significantly affect the adsorption capacity of activated carbon. Rather, the harmful effect may be attributed to a lowered adsorption rate.4,5 Also well known is the faster rate at which fine activated carbon powders reach equilibrium compared to coarse activated carbon, even though the final (equilibrium) amount of material adsorbed per unit weight is the same."

Jan 1, 2015

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By S. S. Xue

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipex® extractant, P,P?-di(2-ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 10 6 Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Jan 1, 2011