Search Documents

By Y. C. Kim

This paper describes the implementational aspects of a blast hole kriging system that has been developedfor the purpose of daily ore/waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore/waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBMIPC AT or XT computers, using the Fortran language and supplemented by a few assembly language routines for the bit- map manipulation. This paper emphasizes the practical implementation requirements of the system and discusses system design considerations.

Jan 1, 1991

By Y. J. Wang

In the, mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs. -quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1997

By Y. C. Kim

Three rock fracture parameters define three points along empirical cumulative size (of rock fragments) distribution curves at Inspiration copper mine. These parameters are: rock quality designation (RQD), longest piece of intact rock and % of +1 inch. The RQD and the longest piece are actually measured on drill hole cores whereas % of +1 inch is visually estimated on the same cores. These size distribution curves are then utilized in a variety of engineering applications such as; slope instability analysis, blast design, copper recovery prediction from heap leaching, etc. The three rock fracture parameters for two dominant rock types (porphyry and schist) in the pit had to be estimated separately due to different rock fracture characteristics.' Both ordinary kriging (OK) with measured hard data only and soft kriging (SFTK) with hard and soft data were used to estimate each parameter. The cross validation of 100 measured sample values served as the-basis for evaluating the potential benefits of SFTK over OK. Use of subjective information during SFTK required obtaining (prior) probability distributions for all three rock fracture parameters. These distributions were obtained from the typical rock fracture parameters observed in drill hole cores falling inside the geologically interpreted structural domains with varying degrees. of fracture intensity and also through direct mapping along the exposed bench faces. Two different types of soft information were developed for this study; namely, Type "A" and Type "K". The former is based on sample distribution of fracture parameters whereas the latter is based on two step estimation designed to narrow the range of variation observed in data Type "A". The results of the cross validation were analyzed using a linear regression of actual values versus estimated values. The results confirm an improvement on the estimates made by SFTK with hard and. both types of soft data over those produced by OK with hard data only.

Jan 1, 1989

By Y. K. Yen

The most serious problem for on-line coarse particle size measurement from a conveyor belt by image analysis is the overlap phenomenon that occurs between adjacent particles. A methodology is developed and described in this paper to estimate the sieve size distribution from the overlapped projected particle images as might be obtained from a conveyor belt. Two aspects of the overlap problem have been taken into consideration. First, several image processing algorithms were studied to find the most suitable technique to separate the projected overlapped particle images for narrow sized particles. These image segmentation algorithms include two-dimensional thresholding, edge detection and Watershed discrimination techniques. The other aspect of the overlap problem is related to the determination of the general kernel function for the partial particle images obtained from the projection of the overlapped particle bed. In this regard, a computer simulation technique was applied to mimic the overlapped particle bed for narrow sized particles, then the general kernel functions of the partial particle images were determined.

Jan 1, 1994

By K. Y. Haramy

A scale-invariant theory of the strength and deformability of rock masses in static equilibrium and at incipient failure is proposed. The theory provides a rationale for designing structures in rock. This paper presents results of experiments conducted by the U.S. Bureau of Mines and theoretical methods to determine and interpret in situ strength of rock masses using the borehole shear tester.

Jan 1, 1995

By Y. J. Wang

The use of controlled recirculation began in the early 1930s. Although this method has been applied in many mines since then, a generalized comprehensive network analysis is still lacking. This paper presents a unique approach in which the ventilation network with a controlled district recirculation is divided into two subsystems: a main subsystem and a recirculation subsystem. The subsystems are analyzed individually, and the results and their relationships are then integrated into discussions of the total ventilation system. The analysis of the recirculation subsystem is facilitated by introducing a nondimensional parameter (A), which represents the ratio of the air quantity for the working face to that for the subsystem. As a result, far and regulator pressures and air power for various recirculation arrangements can be effectively expressed as a function of and the subsystem air quantity. Numerical examples are included.

Jan 1, 1997

By Y. J. Wang

The concept of subsystem characteristic curves for multiple-fan ventilation networks is presented through the construction of characteristic curves for two-fan, series-parallel networks. By considering fans as the individual network branches, the multiple-fan network is viewed as consisting of two components: any one fan branch, which is called the reference fan branch, and its associated subsystem. Thus, F subsystems can be designated for the network with F fan branches. Each subsystem contains one or more fan branches. The subsystem characteristic curve is the pressure-vs.-quantity curve of the subsystem. As illustrated in the example networks, the subsystem characteristic curve is not a strictly increasing curve and does not pass through the origin. The intersection of the characteristic curves for the subsystem and the reference fan branch represents an operating point. Multiple intersections therefore represent multiple operating points.

Jan 1, 1994

By Y. J. Wang

Along with the inexpensive availability of computing hardware, a proliferation of powerful personal computers is being realized throughout the mining industry. People from every arena within the industry are designing, developing, and/or applying mining specific software, which is increasing at a rapid rate. In this section applications (or potential applications) that are being made in the analysis and design of mine systems are discussed, including the design of compressed air networks, the simulation of hoisting operations, analysis of longwall face maintenance, and a summary of computer and software applications for analysis and design of coal operations. In "Computer Aided Design of Mine Compressed Air Networks" the authors describe software, called CompAir, and the underlying theoretical and mathematical foundations of it that can be used to make accurate, cost-effective designs of compressed air systems for mines. It includes algorithms for network analysis and the optimization of pipe diameters. The techniques embodied in the software replace traditional rule-of-thumb approximations which have been used in the past and avoid the operating problems that often result from using average, steady-state parameter values, estimated for ideal operating conditions. CompAir, coded in Turbo Pascal for personal computer use, bases calculations on compressible fluid theory, which gives more accurate results than incompressible fluid theory whenever high flow rates or long line distances are involved. The net- work and pipe diameter analysis is formulated as a nonlinear programming problem. The solution technique requires a trial and error approach that iteratively applies the unconstrained optimal pipe diameter algorithm to successive solutions of the constrained network problem until the diameters become "fixed." The authors conclude by recommending the use of a mine-wide monitoring system to improve cost control and provide a better understanding of flow regimes in compressed air networks.

Jan 1, 1989

By Y. J. Wang

The ventilation network problem, having both fixed and nonfixed operating points as control devices, is examined in this paper. Emphasizing the concept of solving a system of n equations in n unknowns, this paper presents the generalized problem formulation, some conditions under which the problem does not have a unique solution, and a solution procedure based on the Newton (or Newton-Raphson) method. A numerical example is included.

Jan 1, 1989

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1988

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By Y. B. He

The effect of the overflow to underflow (O/U) flowrate ratio of a dense medium cyclone on its performance is tested utilizing a 6" dense medium cyclone and density tracers. The results show that the O/U flowrate ratio is clearly correlated with the separation cut point D50, the separation efficiency Ep, the density differential 0, and short circuiting of the cyclone. Within certain limits, a higher O/U ratio results in a better separation efficiency, a higher D50 and an increased density differential. A lower O/U ratio, on the other hand, reduces the cut point shift and density differential. The phenomenon of short circuiting to the underflow, which is especially significant for fine particles, is directly connected with an excessively low O/U ratio.

Jan 1, 1992

By Erich J. Jacob, Volker O. Meldner

INTRODUCTION Our company has made persistent efforts to utilize the very latest cost-saving technology in tunnel design and construction. However, we were relatively late in joining the clan of slurry shield tunnelers. The challenge came in 1973, when our company was low bidder on a major sewer tunnel in Hamburg, West Germany. The tunnel was to be driven under the harbor region through coarse and fine sands with up to 60 ft hydrostatic head of water. Outer diameter was 15 ft, and length was 2.9 miles. This contract appeared right to enter the new field of slurry face tunneling. We gathered a design-engineering team to develop the machine, called it "Hydroshield", and used it on the project. The good performance of the prototype machine encouraged us to improve and modify the equipment design. The very latest model is now in use on a subway tunnel in Antwerp, Belgium. This tunnel is 21 ft outer diameter and 2.4 miles in total length. In terms of excavated volume it is the world's largest slurry shield contract. While the drive is still in full swing, we are currently preparing for 3 further Hydroshield applications, with diameters ranging from 12 to 32 ft. This paper describes the Hydroshield's salient design features, operational characteristics, construction reliability and performance levels, as experienced in West Germany and Belgium.

Jan 1, 1979

By Ed Schodowski

Wireless technology is a hot topic for anyone involved in the design, operation, maintenance or upgrading of mines or mineral processing plants because wireless technologies overcome barriers that have prevented many useful data inputs. Wireless communications can contribute to worker safety, satisfy environmental concerns, support plant security, track human and physical assets, and improve equipment maintenance. The cost structure of wireless is compelling and users can realize savings ? up to 90 percent less installed cost than wired instruments ? since wireless technology eliminates the need for expenses associated with cabling, engineering, construction and documentation. Many applications previously considered too expensive have become economically feasible with wireless. Two examples are continuous monitoring of safety showers to notify operators when one has been activated, and monitoring effluents to ensure environmental regulations are being met. In many cases, wireless transmitters can be installed where wired devices were too expensive to justify, or were not feasible due to physical or technical barriers. Examples include monitoring temperature measurements inside a rotating reactor or monitoring process variables in a tough, corrosive environment too challenging for a wired solution. Wireless also gives operating personnel mobility with the ability to communicate from remote or hard-to-reach zones. According to a recent Venture Development Corp. survey covering radio frequency (RF) of microwave industrial monitoring and control products, these features are contributing to the expected nationwide growth rate for industrial wireless applications of 19 percent annually from 2007 to 2012 (Taylor, 2008). At the same time, mineral producers have many questions about wireless systems including their applicability, reliability and security in this industry. Just what can wireless do? Is it secure and reliable? Can these instruments stand up to the rigors of the industry? Can wire-less technology provide the flexibility needed for mining applications?

Jan 1, 2009

By Jacob L. Brinkman, Catherine E. Johnson

Researchers are exploring the use of unmanned aerial vehicles (UAV) to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect density-based concentrations as measured by some governing entities, including the Occupational Safety and Health Administration (OSHA). 

By Sean Dessureault

The mining industry has used fleet management systems (FMSs) for decades. These systems were developed long ago in large truck-and-shovel mines, where hardware sales were the core business driver for vendors. These traditional models can be overhauled in the era of the Internet of Things (IoT), Big Data, gamification and low-cost tablet technology. Relatively low-cost tablets are ubiquitous in modern life, and they are packed with communication radios and sensors like Global Positioning System (GPS) and inertial measurement units used widely for games, fitness measures and navigation. These powerful computer devices provide the same, if not more, sensing capability than traditional fleet management hardware, all at a fraction of the cost and without complicated cables or challenging supply lines. 

By D. A. Swanson

Predicting when and at what rate seepage will occur from waste-rock facilities is becoming an integral part of permitting and closure at mines situated in dry climates. Such predictions require development of a conceptual framework that accurately describes how water will percolate through a waste-rock facility. Also needed is a detailed hydrological characterization of the waste-rock facility, including measurement of the hydraulic properties of the waste rock and any potential cover materials. This paper presents a conceptual framework describing unsaturated water flow in a waste-rock facility and describes methods for characterizing the hydrology of a waste-rock facility in a dry climate. The methods are designed to collect site-specific data to support accurate and defensible predictions of long-term seepage rates.

Jan 1, 1998

By Omid Frough, Hossein Changani

Application of Tunnel Boring Machines (TBMs) is one of the main solutions to achieve a safe and high-performance method of construction in hard rock and soft ground tunneling. In order to adequately assess the progress and potential impacts of the tunneling operations with the TBM, it is required to record a series of data during the tunneling and process of the data to evaluate the TBM performance. Applying the right machine parameters during the excavation not only delivers an optimum penetration rate, but also prevents extra downtime due to over excavation or wear of cutting tools. In this paper, the effect of machine and operational parameters on TBM downtimes has been studied and supported with the real examples of TBM operation data.

Dec 1, 2022

By John D. Hanifin, C. Kevin Moon, Eric C. Wang

Value Engineering on Connecticut DOT’s Walk Bridge selected the trenchless option for utility relocation to address the channel crossing’s environmental concerns. The design and construction considerations of the twin micro-tunnel drives and associated shafts are presented. Key challenges included vertical alignment selection to achieve minimum one-tunnel diameter stable cover within thin glacial till underlying extremely soft clay, limited choice of pipe and joint materials meeting stringent non-metallic conduit requirements, thermal grout backfill application, and the close proximity of temporary trestle piles. Mitigation measures were developed for potential point loading pipe damage from remnant boulder fragments in the annular space.

Dec 1, 2022

By William H. Langer

I spent 41 years as a geologist with the US Geological Survey (USGS) conducting geologic studies and preparing peer reviewed maps and reports describing the results of those studies. Since retiring from the USGS in 2011, I have been a consultant specializing in aggregates and other industrial minerals. Consequently, I have had the opportunity and pleasure to apply the information contained in those kinds of geologic maps and reports to real-life situations. About half of my consulting is performing due diligence for mineral resource evaluations of one type or another where resource information has been provided by the property owner. Many of those jobs necessitate that I conduct desktop studies followed by field work. I then use my information to review and comment on the written reports of others; reports variably referred to as geologic reports, resource studies, reserve analyses, and so forth. While there are many well written reports addressing geologic resource issues, I was surprised to see that there are also a significant number of so-called geologic reports that only pay cursory attention to geology. Unfortunately, that lack of rigorous geologic investigation commonly leads to erroneous conclusions. This paper addresses three such reports covering concrete sand, metallurgical gravel, and proppants (frac sand). Although all three examples are located in the Gulf Coastal Plain Province, I do not reveal the exact location of any of the properties for purposes of confidentiality. Furthermore, I have generalized the site descriptions and illustrations. However, all the descriptions faithfully define the geologic situation.

Feb 1, 2024