Search Documents

By Colleen A. M. Gibbs

On July 30, 1979 New Council on Environmental Quality (CEQ) regulations for implementing the procedural provisions of the decade-old National Environmental Policy Act went into effect. These new regulations replace approximately seventy different sets of agency regulations, providing some uniformity throughout the Federal government in the conduct of environmental reviews and preparation of environmental impact statements (EIS). This attempt by the Federal government at a general improvement in the preparation and quality of EIS's presents an opportunity for the mining industry to evaluate how the EIS process for mining proposals can be expedited. The environmental impact statement is often a key element on the critical path of a major mining project. Preparation of the EIS is ordinarily the responsibility of the Federal agency with primary decision-making authority over the project. Still, the proponent, i.e. the mining company, can play a major role in the process and have a major impact on the timeliness and adequacy of the effort. Typically, the Proponent will conduct (or will hire consultants to conduct) environmental baseline studies of, for example, air quality, wildlife, geology, water quality, vegetation and archaeology. These studies are then compiled into an environmental report and submitted to the agency. The agency verifies the data and incorporates them into the environmental impact statement.

Jan 1, 1979

By Thomas F. Clemens

This paper covers various changes in government regulations, taxation, and legislation for the past two plus years and the up- coming one. Part of the paper will discuss recent business conditions and how they have affected the cement and lime industry.

Jan 1, 1983

By W. Jacobi, B. Haider, D. Regulla, J. Huber

[Introductory Remarks] Thermoluminescence (TL) detectors are widely used for the dosimetry of X- and[ y]-rays. Also filter devices for radon daughter monitoring have been developed in which the a activity on the filter was measured with TL-detectors (Breslin et al., 1977). For this purpose normal LiF-tablets with a thickness of 0.4 - 1 mm were used. However the lower detection limit of such TLmonitors for radon daughters is relative high, especially in areas with a high [y]-background, due to the low [a /-y]-sensitivity ratio of such thick LiF-detectors. This [a/y]-sensitivity ratio can be increased if TL-detectors are used whose thickness is comparable with the range of [a]-particles. On the basis of this consideration we have developed a simple light weighted and sensitive TL-monitor for the measurement of the cumulative radon daughter exposure in air. [Description of the "Monitor] The monitor consists of two parts: The sampling pump with the accumulator, and the sampling probe which contains the air filter and TL-detector system. Both parts are connected with a plastic tube. For operation in mines a light weight, portable air sampler with a built-in accumulator (DuPont model 125 and 200, 400 g) is used which enables an adjustable, constant flow rate in the range of 7.5 -12 1/h. These air samplers allow a sampling period of 10 hours before recharging is necessary. For radon daughter measurements in houses this pump is replaced by a larger, netoperated pump with a flow rate of 180 1/h. Figure 1 shows a schematic cross section through the sampling probe whose weight is 40 g. The radon daughters are collected on a hydrophob membrane filter (Sartorius) with an effective filter diameter of 11 mm and a pore diameter of 3 µm; its collection efficiency for radon daughters is [>] 95%. Above the filter the detector system is mounted. It consists of two thin Tm-activated CaSO4-TL films of 8 mm diameter on a Al-carrier foil manufactured by Matsushita Inc., Japan. The thickness of the TL-film is 6 mg/cm2, which is comparable with the range of a rays. The first detector is faced in 3.5 mm distance above the filter; in addition to the ambient y background this detector is exposed to the [a] and ß radiation from the radon daughters on the filter. Between the first and the second TL-detector is an Al-absorber of 0.5 mm thickness which shields this detector against the [a] radiation and partly also to the ß radiation from the filter. Both detectors have the same [y] shielding. After air sampling both TL-detectors are read-out with a commercial, hot-air reader (Matsushita Inc. / Japan, Model 505 A). The glow-curves are identical for [a and y] rays (Regulla et al., 1980). The integral TLsignal from both detectors is displayed in mR-units (or mR-equivalent). The difference between the response of the unshielded TL-detector above the filter and the shielded TL-detector is proportional to the time-integral of the filter activity, integrated over the sampling period. Calibration and Intercomparison Measurements] The linearity of the a response was checked with a 241Am-source for an [a] fluence on the detector surface of 5400 [a's/cm2•s] in the range of 102 -105 mR-equivalent. Within the experimental error of 15% the response function is linear. The TLD-monitor was calibrated for radon daughters in air by comparison with a calibrated integrating, monitor (WLM-meter) equipped with a Si-surface barrier detector and a direct electronic read-out; this instrument was developed by us for area monitoring some years ago (Haider et al., 1976). The results of simultaneous measurements with the TL-monitor and the electronic WLM-meter in mine areas and in indoor air of houses are shown in figure 2. On the abscissa the mean potential [a] energy concentration (in WL) during the sampling period is given which was derived from the measurements with the electronic WLM-meter. On the ordinate the corresponding response of the TLDmonitor to radon daughters (difference between both TL-detectors) is displayed, expressed in terms of mRequivalent per liter sampled air. It follows from this comparison a linear relationship over the whole range of 0.005 - 5 WL with a standard deviation of 10%. The resulting calibration factor for the TLD-monitor is 18± 2 mRequiv per WL • 1.

Jan 1, 1981

By W. D. Bullock

The King-Beaver mine of Asbestos Corporation Limited operates an open pit in the city of Thetford Mines, Quebec. The approximate loca-tion of the open pit is at Latitude 46° 02' North and Longitude 71° 20' West. The general topography is 1020 feet above sea level. Thirty-six percent of the company's scheduled asbestos ore production, for the Thetford Mines area, comes from the King-Beaver pit. The pit operates 24 hours a day, six days a week. Normal production is 10,500 tons of ore per day at a waste to ore ratio of 2 to 1. The remaining ore requirements are mined from the King-Beaver underground mine and the British-Canadian mine.

Jan 1, 1980

By M. D. McInnis

The Jualin Gold Prospect is centered on Johnson Creek, approximately 40 air miles north-west of Juneau, Alaska. The property is on the southern end of the Kakuhan Range with Berners Bay immediately to the south and Lynn Canal to the west. The property is accessible directly by helicopter from Juneau or by float plane to the head of a 5.5 mile gravel road that begins on the north side of Berners Bay and terminates at the old workings of the Jualin Mine near the center of the property.

Jan 1, 1989

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

By U. Thorley

This paper presents an overview of surface mining activity in the Canadian oil sands and how the mine operators interact with the province of Alberta's Mine Financial Security Program (MFSP), which took effect April 1, 2011. The MFSP approach to reclamation assurance results in the government of Alberta sharing a portion of reclamation liability through the majority of an oil sand mine's life. In order to determine the potential fiscal magnitude of this shared liability, an examination of the expected costs of oil sands reclamation activities through a study of corporate asset retirement obligation (ARO) liabilities and other corporate disclosures is presented. The province of Alberta's Environmental Protection Security Fund (EPSF), which formerly secured oil sands mine reclamation activities is discussed. Reclamation costs in the oil sands are poorly understood. The MFSP provides what it characterizes as a conservative estimate of C$75,000/ha, while corporate disclosures by Canadian Oil Sands Ltd. place expected costs at C$180,000/ha. There is significant risk associated with the apparent uncertainty surrounding reclamation costs.

Jan 1, 2012

By Shosei Serata

Salt cavities have been proven to be a suitable structure for underground storage of various matters in gas, liquid or solid form. Since the technique of underground storage was developed mainly through field experiences in solution mining, a wider use of solution cavities for storage of gaseous and solid matters requires evaluation of three basic rock mechanics problems; cavity instability, boundary rock failure and surface subsidence. Cavity instability is due to the non-linear long-term creep properties of the surrounding ground media which are sensitive to cavity pressure changes associated with the storage. The cavity boundary rock failure is caused by the loss of effective confining pressure to the boundary rock media in the process of storage of gaseous and solid matters. Surface subsidence is the final outcome of the stress envelope originated around a cavity, eventually reaching the ground surface. The rock mechanics processes of instability, failure and surface subsidence are explained by using various field examples in salt domes and bedded formations. Methods of solving the problems are discussed including stress relief, stress control and computer optimization of design.

Jan 1, 1973

By B. Das, D. D. Mishra, M. I. Ansari

Experiments conducted with a 75-mm-diem hydroryclone have shown it is possible to obtain an iron ore concentrate containing 60% Fe. 2.65% SiO2, and 4.0% Al2O3 from Barsua iron-ore washing-plant slimes. About 60% of the iron values are recovered from slimes containing approximately 49% Fe, 8.9% A1203 and 11% SiO2. The obtained products can be used in the sinter feed for iron and steel making. The key to achieving process success lies in establishing the correct cut point (d50) of the hydrocyclone through the manipulation of operating and design variables, such as spigot and vortex finder diameter, solids concentration and operating pressure. The cyclone efficiency is represented by the partition curve. The cyclone performance, evaluated mathematically from the reduced efficiency curve, is represented by the equation Y = 100[1 -exp(-axb)], where: •X = did 50, •Y = corrected of efficiency (%) and •a and b are constants.

Jan 1, 1994

By James M. Prudden, E. P. Jucevic

The Divide mining district occupies the center of a Tertiary caldera hosting the famous Divide silver lode and the crosscutting Gold Mountain mines. The northwest-southeast trending silver lode hosted ore with typically a 100:1 silver:gold ratio, high molybdenum content and argillic alteration dated at 16.5 m.y. within the Fraction Tuff. The east-west trending Oddie Rhyolite flow dome at Gold Mountain experienced possibly several periods of resurgence with repetitive silicification, brecciation and attendant precious metal deposition forming stockwork type mineralization. Silver-gold ratios average 10:1 for the mineralization phase of this 16.4 m.y. intrusive event. Similar chalcedonic mineralization registering a 3:1 silver:gold ratio cements conformable breccias within the Oddie Rhyolite basal flows unconformably overlying the Siebert Tuff on the northern flanks of Gold Mountain. Gray and red chalcedonic breccia matrix in the King Tonopah member of the Fraction Tuff contains a 50:1 silver :gold ratio.

Jan 1, 1990

By David D. Lambert

REE analyses of cumulate plagioclase from the PGE ore zone of the Stillwater Complex indicate that pressure fluctuations in the magma chamber acting on a single magma can- not be responsible for features such as the reappearance of Mg-rich olivine on the liquidus. The data is more consistent with a model involving multiple injection and mixing of geochemically distinct magmas. The PGE bearing sulfides of the J-M Reef are associated with such a re- appearance of olivine, indicating that the unusual location of the ore zone may be related to the addition of new magma, compositionally distinct from magmas that produced cumulates in the Ultramafic zone of the complex.

Jan 1, 1981

By MYRIAM FRANCOEUR, JOHN R.R. BOWLING, ADAM MCFADDEN

As duct-fan systems push the envelope of power, length and cost, their design calls for a more comprehensive technoeconomic analysis to ensure they deliver the expected results without failure and cost overrun. This work explores the numerous factors to include in the design of an extensive (semi-)rigid duct-fan system. Besides delivering a given airflow, the system must satisfy component limitations and power constraints during its lifetime. We evaluate the assumptions underlying the positioning of in-line booster fans in a long gapless duct-fan system and propose a strategy for specifying the location and blade pitch of successive booster fans to prevent system failure due to a partial vacuum.

Oct 1, 2022

By K. O. Groves

Although chlorine oxidation has been found to be effective in destroying the CN ion, an excess of chlorine is needed to drive the reaction to completion. This often results in the formation of residual chloramines, which are toxic to aquatic life and often regulated by various states. The interhalogen, bromine chloride (BrCl), has been found to be just as effective but without the formation of persistent, residual chloramines. The hydrolysis and subsequent disproportionation of the highly-polar BrCl molecule essentially yields a solution of hypobromous acid (HOBr) and nonoxidizing hydrochloric acid (HC1). Studies have been carried out to directly compare the mechanism of CN destruction with chlorine and bromine chloride.

Jan 1, 1982

By W. –E. Marx, M. Faber, R. Pollak, I. Astberg

INTRODUCTION Essentially three strategies are pursued in parallel for protecting the underground working force in mining against the consequences of methane ignitions which might lead to explosions: • Sufficient ventilation for avoiding the formation of explosive methane-air mixtures. • Avoiding sources of ignition caused possibly by electrical equipment or friction. • Structural explosion protection for limiting explosion propagation to the farthest-going extent for the case that methane is fired because of failing of the above preventive measures taken. The corresponding methods taken in mechanized roadheadings with point-attack roadheaders in German coalmining are subject of this paper. VENTILATION In ventilation of roadheading sites the following is to be considered in respect of methane control: • Sufficient air flows by volume being cycled to the heading face for diluting released methane to safe concentrations. • Sufficient local air velocities for effective mixing of methane and air in the whole heading site, in particular directly on the heading face and underneath the roof. Furthermore, ventilation needs to be laid out in a way that cut- ting does not result in health affecting dust exposure at any working place. Accordingly, the ventilation systems shown on Fig. 1 including primary and, if necessary, secondary auxiliary ventilation air ducts as well as dedusters, are used in roadheadings. This equipment is run according to the following principles: • If the roadheader is at standstill, the heading face is ventilated by the free air jet from the blowing duct closest to the face. In this operation phase the deduster is shut-down. • During cutting, the exhaust of the blowing air duct is automatically closed, and the deduster is taken into operation. The in- coming fresh air is now locally discharged via a lateral orifice, or distributed by Coanda-type ducts from the primary or secondary ventilation air duct. In this way, a stable dust wall not disturbed by the jet of the air duct is formed in front of the heading face. Only the ventilation air stream taken in by suction of the close-to-face deduster is passed through the inby zone of the heading face (over approx. 20 m). The clean exhaust of the deduster is dischayed to the roadway in some distance outby. Immediately at the heading face, methane accumulations possibly released by cutting are diluted by compressed-air jets from air-movers located near the roof which assure more rapid motion of the air without distuhing the dust wall. • In the zone of overlapping of primary and secondary duct and the deduster - that zone possibly is poorly ventilated during cutting - sufficient local air speed is assured by Coanda-type ducts or additional ventilation jets for avoiding methane accumulation. The regulations of the inspectorate specifies geometrical conditions to be met with these configurations of ventilation equipment. In-seam roadways are ventilated at rates > 0,5 m/s. For dedusters, present-day ventilation air flows are of 600-800 m+/ min. Ventilation monitoring and control is assured by units for measuring methane and ventilation air flows. If pre-set thresholds are exceeded or fallen short of, these measuring units shut-down - dependent on potential hazard - any not intrinsically safe electrical equipment in the roadheading, either totally or in limited zones. In addition, CO-measuring units near the roadway en- trance serve for early detection of mine fires. In spite of this ventilation layout and the equipment used and in spite of the water spray systems on the cutting head (discussed later in this paper) several cases of methane ignition and subsequent burning off (however, no explosions) have been recorded in the recent past. Therefore, the above-described ventilation is nowadays complemented in many cases by machine-mounted ventilation equipment for the immediate surroundings of the cutting head. Ventilation of the surroundings of the cutting head Investigations carried out subsequent to the above-mentioned gas ignitions have shown that the high ventilation air speed necessary for rapid dilution of methane could not permanently be arrived at in the following zones: • The direct zone of cutting, in particular during sumping. • The floor zone above the debris, predominantly below the cut- ting head. Accordingly, VOEST ALPINE-Bergtechnik, a producer of mining machinery, in cooperation with DMT developed for point- alttack roadheaders a novel machine-mounted ventilation equipment, the Jet-Block" (AERO SAFE Jet-Block) shown on Fig. 2. This system allows to ventilate the above-mentioned critical zones with high flow speeds. One AS Jet-Block is mounted on each side of the boom approx. 0.5 m behind the cutting head. The blocks discharge compressed-air jets with high energy from 10 nozzles per block into the hazardous zones (Fig. 3). Two nozzles of each jet block are tangentially oriented toward the upper circumference of the cutting head, the others are arranged fan-like with orientation to the heading face underneath the cutting head and the debris. The nozzle array of the blocks as well as the com-

Jan 1, 1997

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By Alvaro Veizaga, Samuel Cuellar

In recent years, Industry 4.0 has generated a change in the way companies in various industrial sectors design, produce and deliver products and services, and is focused on the interconnection of systems, the advanced access and management of large amounts of data in real time, and the implementation of emerging technologies such as the Internet of Things (IoT). Artificial intelligence (AI), machine learning (ML), digital twins (DT), robotics, virtual and augmented reality (VR/AR), among others [1]. DTs are accurate and dynamic virtual models that replicate physical systems, where it is possible to simulate and optimize operations before implementing real-world changes [3]. These features make it possible to reduce investment costs, minimize risks and improve strategic decision-making. These benefits are of utmost importance for tailings storage facilities (TSF), since they are facilities aimed at the safe storage of tailings and with the constant need for growth [4]. This paper evaluates the applicability of a DT in a TSF from a conceptual perspective, providing the advantages of its implementation, but also the barriers identified in the industry based on the authors’ experience.

Feb 1, 2025

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By John P. Norton

Microcystaline silica has been mined in Illinois from the Clear Creek formation since the turn of the century, especially in the area around Tamms in Alexander County, in the southernmost part of the state. Production of this silica, consumed mainly by the abrasives and coatings industries but also sought after for many filler/extender uses, has grown with the economy with several new applications overshadowing traditional markets in recent years. Such an important commodity was given the early attention of the Illinois State Geological Survey and a very complete report was issued in 1953 (Report of Investigations No. 166), authored by J. E. Lamar. The mining and processing of the silica ore has changed very little since the first reported production in 1906, although emphasis has been placed on the production of the finer sized grades to meet newer market requirements. Industrial Mineral Notes 40, published by the Illinois State Geological Survey in June 1970, describes a method by which a less than 1-micron fraction could be commercially produced from the readily available finest commercial grade presently being marketed (99% minus 10 microns). The finer grades exhibit to a lesser degree the reinforcement, high flatting efficiency, thickening and dry brightness properties associated with the synthetically produced silicas. It is expected that the extremely fine grades of microcrystaline silica will become accepted in the markets that now use a combination of precipitated silica and less expensive extender/filler minerals such as kaolin or calcium carbonate.

Jan 1, 1976

By R. A. MacGregor

The Stanreck mine of Stanreck Uranium Mines Limited in located on Quirks Lake in the Elliot lake - Blind River area of Northern Ontario. It is approximately 25 miles north of the north shore of Lake Huron, equidistant between the cities of Sudbury and Sault Ste. Marie. The property was developed ad brought into production at a rate of 3,000 tens of ore/day during the uranium boom of the mid 1950's. By 1960 mine waters were becoming quite acid through the activity of bacteria. Treatment of this water was begun for pollution control and a small amount of uranium which had been leached from the ore by these acid waters was recovered. Development of bacterial leaching with a view to increasing production by this method commenced in December 1962. Subsequently, it was succeesfull in producing 10,000 - 15,000 lbs. of U308/month. Since late 1964 uranium production has been obtained solely from bacterial leaching. A rare earth concentrate was also made for its yttrium content during 1966 and 1967. This paper describes the development, operation and methods used in the underground bacterial leaching process.

Jan 1, 1969

By A. L. Martikainen

Booster fans increase air pressure to overcome resistance, the objective being to force adequate amounts of air through distant workings. They are used in areas that are difficult or uneconomic to ventilate with main fans alone. Booster fans are currently permitted in underground coal mines in some countries; the United Kingdom, South Africa, Australia and Canada have been defined as major users. Booster fans are not allowed in the US bituminous and lignite coal mining operations at the present time due to safety concerns. This paper presents the history of booster fan use in coal mines of the United States during the last 90 years. Changes in regulations, as well as advantages and disadvantages of booster fan use, are discussed. Research and petitions for booster fan use are highlighted in order to bring the debate into focus.

Jan 1, 2010