Search Documents

By J. Janin, J. F. Bougard

Development of improved transportation networks in major urban centers has led more and more to underground construction, the only reasonable solution for decreasing surface traffic congestion. Excavations required by these projects usually cause decompression of the surrounding soil mass which results in subsidence of several centimeters. While these magnitudes of subsidence have no consequences in undeveloped areas, they are often unacceptable in urban areas where existing buildings, structures and utilities are endangered. Recent tunneling projects for the extension of the Paris Metropolitan Transit System (R.A.T.P.) underground network were carried out with this in view and gave rise to the development of a number of innovative techniques for minimizing ground decompression and subsidence. As shown in Figure 1, the recent R.A.T.P. expansion program includes a new express metro, 46 km long, crossing Paris from East to West, and the extension of many existing metro lines in the suburbs. From the start, R.A.T.P. was faced with many unique technical problems for which there was little precedent experience. The structures to be built have large dimensions, with cross-sections typically ranging from 40 to 300 m2, and exceptionally to 600 m2. The new lines are often very deep because the shallow profile is already congested by the existing metro, interceptors, sewers and a very large number of utilities. As a result, new construction is often below ground water level by as much as 20 m. Moreover, the geology varies widely from hard limestone with compressive strength over 1500 kg/cm2 to inconsistent water bearing sand. Finally, curves in the East-West line must have a minimum radius of 500 m which frequently forces the alignment to pass below existing structures, buildings and monuments.

Jan 1, 1974

By Steven I. Majtenyi

There is a growing interest among transportation planners to make more use of the subsurface to preserve the landscape and make transportation more efficient and economical. At the present time, utilization of the underground for transportation facilities is severely restrained by the adverse environmental impact and high construction costs. However, recent studies performed by the United States Department of Transportation indicate that, in spite of such problems, the volume of underground construction has significantly increased during recent years and projections point to continuation of these trends(1). It is estimated that the total volume of transportation tunnel construction will exceed $4 billion in this decade. This level of Investment justifies a significant research program. Due to the common interest in transportation tunnels and to the similarities of problems encountered during their construction, the tunneling research activities of the Federal Highway Administration (FHWA) are closely coordinated with the programs other agencies of the U. S. Department of Transportation DOT); specifically, the Federal Railroad Administration (PRA) and the Urban mass Transportation Administration (UMTA). The FHWA is responsive to the particular needs of these agencies but will benefit from the research results obtained also. In 1971, the Office of Secretary, DOT, initiated plans for an overall coordination of the DOT, FICA, UMTA, and FHWA tunneling research activities. The objectives of this effort have been to reduce tunneling costs by 30% and to increase the rate of excavation by 200% within 10 years. This coordinated program was developed and promoted during 1972 and 1973 by Dr. Eugene L. Foster, at that

Jan 1, 1974

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By R. J. Pruett

The Georgia kaolin district is the world’s largest producer of kaolin. Georgia production tripled from 2.87 Mt (3.17 million st) in 1968 to8.35 Mt (9.2 million st) in 1998. Development of the Georgia kaolin industry can be traced to the identification of the mineral resource, the adoption of innovative process technologies and the creation of markets for kaolin. Georgia kaolin is an abundant and high-quality resource that shows a range of advantageous properties. Technical developments in wet processing, delamination and calcination allowed production of high-value products. The use of kaolin pigments in the paper industry provided a market that absorbed the rapid growth in kaolin production.

Jan 1, 2000

By Amanda Elioff

Success of the Gold Line Eastside Ex-tension rail tunnels in Los Angeles, CA has prompted the Los Angeles County Metropolitan Transportation Authority?s (Metro) planning new rail lines to include underground alternatives. The Westside Extension Transit Corridor alternatives include up to 27 km (17 miles) of subway to be constructed in soft ground. The routes will require construction in Los Angeles? ?potential methane zone,? which was not considered for subway construction until recently. Slurry face tunnel boring machines (TBM) will likely be specified.

Jan 1, 2009

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

By L. Lacerda

Spray-on ground support membranes (GSM) or thin support liners hold today perhaps as much potential to impact underground (u/g) ground support operations as dry and later wet-mix shotcrete when introduced to mining in the latter part of the 20th century. This emerging technology has come a long way from the time the first single component experimental coatings were tested in the mid-1980s. Due to a number of factors, including occupational health risk and mine safety regulations, it has taken quite some time for the development of non-hazardous membrane products. However, at this junction most existing u/g mines that employ more conventional forms of ground support could benefit from evaluating GSM technology as a means of improving safety and the bottom line. The same is especially true for future mine developments. This paper describes Master Builders Inc.’s CS1251 GSM product and its implementation. It discusses the situations in which GSM may replace other forms of ground support. Furthermore, it evaluates GSM costs & safety issues and looks at present applications and the potentially bright future of this technology.

Jan 1, 2002

By S. E. Pérez-Fontes

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. The oxygen concentration in the process gas was set to 40% and 70% (by volume) and a heating rate of 40°C/min was used. Response variables included the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles and by thermochemical and mass balance calculations to reproduce the DSC and TGA data. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction as a function of time.

Jan 1, 2007

By Raymond W. Henn

The 31th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, in Golden, CO June 7-11, 2010. The field demonstration portion of the course was conducted June 10 at wlh Construction Co.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods performed under various field conditions.

Jan 1, 2010

By Richard E. Gray

The Office of Surface Mining Reclamation and Enforcement (OSM) is preparing an Abandoned Mined Lands Reclamation Control Technology Hand- book. (l) GAI Consultants, Inc. , recently prepared Chapter 2 on Mine Subsidence Control which contains a summary of subsidence abatement measures plus two new decision matrices for evaluating the subsidence abatement options that might be considered for a particular problem. These decision matrices are presented for information. Review of the subsidence abatement methods resulted in identification of items where research may impact the current state of technology in mine subsidence control. These research needs are presented to stimulate discussion of their importance in subsidence abatement and to encourage funding agencies, researchers, and practitioners to work on them.

Jan 1, 1982

By Paul C. Schmall, Lucian P. Spiteri, Arthur B. Corwin

Moving groundwater is generally recognized as the most adversarial condition for ground freezing. Moving groundwater can occur due to natural or man-induced groundwater flow, but either way may result in freeze formation difficulties. History has shown that if the condition goes undetected, catastrophic failure of the frozen shaft or excavation can occur. The success of ground freezing under potentially flowing groundwater conditions depends on an evaluation of the likelihood for this condition; an accurate and early diagnosis, with a careful evaluation of freeze pipe temperatures and piezometer water levels; and timely reaction to mitigate the possible delays. Successful remedial measures have included the reduction of ground permeability by modifying the soil properties between the freeze pipes with various kinds of grouting, or increasing the freezing effect by adding freeze pipes and/or the use of liquid nitrogen as the freezing agent.

Jan 1, 2007

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

By Joachim Klein, Frank Reimann

Nodular-graphite cast iron (GGG) is a material similar to steel, and one which exhibits excellent properties, in particular for components exposed to pressure. GGG cast iron has been used in many cases when sinking mine shafts with conventional tubbing. With linings made of cast iron tubbings (the backfill concrete is not integrated into the calculations, and merely serves as bedding) the properties of the cast iron can be made full use of, provided the tubbing is made to the appropriate cross-section. Calculations have shown that better static values can be arrived at when using cross-sections other than those of tubbings made to conventional German standard. The cross-sectional design of the new types of shaft lining made from GGG is to be developed on these lines irrespective of the cast iron structure being only stressed component or its restistance function being combined with the one of concrete. GGG 50 is used for the first time to make the reinforcing inner liner of a main shaft currently sunk in Germany. The physical properties of nodular-graphite cast iron, strength and deformability, suggest that, in the future, its application will not be restricted to shaft support but also in tunneling. New moulding techniques with better three-dimensional modelling resulted in new tubbing designs as installed e.g. for the Hannover underground at present. Shield-driven tunnels have to withstand earth and water pressure, apart from axial machine loads. In this field time is money as well. Therefore easy handling and quick installation are necessary for successful, use. Last but not least, safety is of first-order importance for work in shaft sinking and tunneling. Cast iron lining systems, accordingly, are adequate systems, in particular for excavations underneath water for transport systems and for goods and passengers.

Jan 1, 1987

By A. Kevin Beaton, Robert W. Laakso

The desire for dry passageways promotes the NATM as it provides a final support system most suitable for the installation of a waterproofing membrane. Waterproofing during construction is a cost effective way to enhance safety and function as well as increasing the life of an underground structure. The NATM approach utilizes the surrounding mass as an integral element of the "ringlike" support system. At the Pennsylvania Turnpike Commission Lehigh Tunnel No. 2 various rock classifications were determined to require support measures ranging from 2 to 12 inches of shotcrete along with spiling, wire mesh, deformed bar, lattice girders and rock bolts as needed. Field instrumentation and monitoring programmes are a key factor for the success of the NATM. When the support "shell" stabilizes smoothing shotcrete, waterproofing and a final liner can be placed.

Jan 1, 1991

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

Komatsu America International has introduced two new hydraulic excavators. They can work in congested and confined areas. The tight tail swing radius of the PC128US-2 and PC22-8USLC-2 enables the excavators to minimize the work space. The units can operate in confined work settings that are inaccessible or counterproductive to traditional machines. Even the door is designed for tight working conditions. A convex door slides open along the exterior curve of the cab, rather than swinging out on hinges past tracks. And the excavators’ tight tail swing design allows them to load within the track width of the machine.

Jan 1, 2000

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits, thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium. Key Words: Rhenium, Ammonium Perrhenate, Extractive Metallurgy

Feb 27, 2013