Search Documents

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By S. K. MONDAL, K. K. K. SINGH, S. Singh, R. K. TIWARY, S. K. Chaulya, G. C. MONDAL, R. S. Singh, T. B. SINGH

In this work, a comprehensive field study was carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling was conducted to envisage dust concentration due to existing and closed mines in the region. The air quality modeling exercise predicted that particulate-matter levels of PM10 and PM2.5 might increase in the ranges of 3.2 to 23.1 and 2.1 to 8.9 μg/m3, respectively, due to mining activities when some of the closed mines will be operated in the region without controlled emission. The predicted total PM10 and PM2.5 at the selected receptor locations were in the ranges of 86.39 to 194.89 and 34.82 to 99.55 μg/m3, respectively. Adequate measures were suggested to control air pollution from mining activities, and an intelligent dry fog system was designed to suppress dust emission efficiently from mineral processing plants and opencast mines. The developed system has special features for facilitating eco-friendly mining.

By R. W. Sayers

The Duval Corporation porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an economic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex copper-gold-silver ore is treated in a 4,000 tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamorphism and hydrothermal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes further altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle Formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony Formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls.

Jan 1, 1968

By Ben V. Petersen

Surveying is to tunneling, as a steering wheel is to a car—somewhat essential if you want to end up in the right place. The principles of tunnel surveying have remained unchanged since the first tunnels were constructed: To mathematically connect the selected start and end points of a tunnel and physically translate that alignment onto the ground. The alternative is just dead-reckoning and leaves the probably less than satisfying end results to chance. Today’s laser-guided tunnels often have to thread the needle through a maze of soil types, utilities, structural features and other underground considerations. Surveying makes it possible.

Jan 1, 2005

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By Steve Kral

Americans are taking a more critical view of various environmental laws because the effects of those laws are becoming more pervasive and intrusive, according to William Perry Pendley. And Secretary of the Interior Bruce Babbitt is seemingly so unpopular in the West, he no longer campaigns there for Clinton Administration policies. Pendley is president and chief legal officer of the Mountain States Legal Foundation, a public service, non-profit law association that takes on property rights cases for people who cannot afford representation. He was one of the luncheon speakers at the 101st Northwest Mining Association meeting, held in Spokane, WA in early December.

Jan 1, 1996

By C. L. Lin

A PC image-based on-line coarse particle size analyzer has been developed to measure particle size distributions under plant situations where overlapped particles are being transported on a moving belt conveyor. Although previous testing had shown satisfactory performance of this image-based system for separated particle size measurements (the non-overlapped case), it was necessary to modify original algorithms in order to solve the overlap problem and make the system suitable for plant operations. On-site testing has been conducted at a large copper concentrator in the southwestern U.S. for further investigation of the overlap problem.

Jan 1, 1995

By R. Scheffel, R. Washnock, G. Zarate

"The second survey of global copper leaching operations has been completed, the data published in 1998 has been updated. A survey questionnaire was sent to 40 identified copper leach operations around the world including those leach properties still in operation that responded to the 1998 survey. This paper lists the results of 26 operations that responded to the survey. Selected information from the survey is represented in graphical form. INTRODUCTION Copper leaching was first performed by truck dumping huge monolithic stockpiles of ore and flooding the surface with leach solution or lixiviant with little understanding to the parameters that support optimum recovery of the metal. Heap leaching has evolved into a controlled process whereby a complex low grade ore is stacked in shallow lifts (under 10 m in most cases). The ore is usually crushed and agglomerated, conveyor stacked on an engineered containment system (leach pad) and irrigated in a controlled manner. The lixiviant chemistry is designed to extract the optimum amount of metal from the ore. At first glance, heap leaching appears to be simple in nature. In fact, it is a very complex process. A plethora of technologies such as material handling, environmental control, analytical techniques, solution chemistry, hydrology and many others contribute to the design and operation of a heap leach. Heap leaching requires an inter-disciplinary approach between geologists, mining engineers and metallurgists. Many operational factors affect heap leaching. The process must address climatic factors, flexible operation, quality control before and after leaching, physical characteristics of the ore, geology, mineralogy, reagent consumption, solution application rate and methods (wobblers or emitters), particle size, and favorable conditions for bacterial growth and survival. Predicting, troubleshooting, and optimization of leach recovery is a significant challenge when considering the number of variables involved and their interactions The survey updates many of these key operating parameters to the current state of the art. It should provide the reader an excellent benchmarking summary of these factors on a site-by-site basis."

Jan 1, 2016

By M. E. Rossi

This paper discusses the use of Conditional Simulation (CS) models to provide mill feed grade profiles for different time periods. The conventional approach of classifying block estimates as ore or waste generally does not adequately represent dilution, lost ore and the anticipated grade control data, including variability of mill feed from the pit and possible stockpiles. The detailed simulation of grade control practices can be done, but at the Pre- or Feasibility stage of the project may be impractical, since drawing dig limits on multiple benches is tedious and time consuming. Using the Feasibility Grade Control (FGC) method as developed by the Centre for Computational Geostatistics (CCG, University of Alberta-Edmonton), the CS models can be processed quickly to establish dilution and lost ore, and predict daily or short-term feed to the mill. The simulated nodes can be aggregated into selective mining units with adequate representation of likely geometries to be recovered from the pit, to mimic anticipated selectivity. An example from a large copper deposit is shown. The study provides an estimated stream of tonnages and grades fed to the plant by mining periods of interest and based on a specific mine design and schedule. The resulting cash flows support the economic and financial analyses of the Feasibility Study; also leads to improving mine schedules; and aids in developing blending schemes if necessary. INTRODUCTION The conventional approach of separating mineralized material into ore or waste categories does not always include a realistic amount of dilution and ore loss. Also, often it does not provide a good estimate of the grade that will be fed to the mill. If the grade control estimates are unbiased, they will over the long run represent the long-term average of grades fed to the mill; but the anticipated variability of mill feed from the pit and stockpile sources may be misrepresented. Some references on traditional grade control implementations can be found in Chunnett (1982); Davis et al. (1989); Srivastava et al. (1992); and Nowak (1992). Alternative methods based on economic variables improved significantly on the purely grade-based control methods, see Douglas et al. (1994). Further developments involved the use of geostatistical conditional simulations (CS) and profit models, which in several cases have been successfully implemented (Aguilar and Rossi, 1996; Rossi, 1997; Deutsch et al., 2000; Norrena and Deutsch, 2002; Neufeld, 2005; Jewbali and Dimitrakopoulos, 2009). But they can be impractical, mostly due to the lack of understanding of the methodology involved; even if semi-automatic dig limit drawing is implemented, there is always a need for is tedious and time consuming checking and corrections, even if using a single profit model derived from the simulated grades.

Jan 1, 2019

By Terry B. Linde, William M. Dowall

The recently completed In-Pit Crushing and Conveying Project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109,000 tonnes per day of copper ore, utilizing regenerative conveyors capable of providing over 5.5 megawatts (7,000 hp) of equivalent electrical energy. This paper describes the key aspects of the project and includes: Original project objectives; System design criteria; System description; Optimization studies; Major design features; Equipment description; and System commissioning.

Jan 1, 1993

By Syd S. Peng

According to accident statistics (l, 2), roof fall accidents occur quite frequently at the intersections of underground? openings and account for up to 30% of the roof fall fatalities. But this figure will certainly go up considerably if roof falls not associated with any fatal accident are included in the analysis. Unfortunately, nonfatal roof falls are seldom documented. In the underground coal mines, there are two types of entry intersections. One is the three-way (V type) and the other is the four-way (T type) intersections. A three-way intersection occurs whenever the mainline track haulageway turns at an angle into a section haulageway. The four-way intersections by far the most common type in the U.S. under-ground coal mines are formed by the intersections of two entries which are oriented perpendicular to each other or by the intersections of entries and crosscuts. However, crosscuts are frequently driven at an angle to the entry to facilitate machine movements. The four-way intersections formed by this method of crosscut development are angled. At the intersection of two underground openings, the diagonal roof span is wider than the width of each individual opening. This is one of the major reasons why roof falls occur more likely at the intersections than in the entry between pillars. Consequently, special intersection support plans are usually employed (Figs. 1 and 2) for intersections. The most popular practices are to decrease roof bolt spacing 1 ft. less than or to increase roof bolt length 1 to 2 ft. longer than those employed in the entry between pillars (3). The increase in bolt length or decrease in bolt spacing can be applied to all of the bolts in the intersection or employed only for the strategically located bolts depending on the individual mine practices. These rather generalized practices seems to be adequate for some areas but in many cases inadequate for others. Occasionally, the neighboring two lines of chain pillars are staggered such that the crosscuts in one row of chain pillars face the centers of the chain pillars in the neigh-boring rows. This layout forms T-type three-way intersections which are also inadequate for most weak roofs (3, 4). A study was therefore initiated to develop special techniques for intersection supports. The first phase of the study was the analysis of the stress fields for the underground entry intersections. A three-dimensional stress analysis was necessary for this purpose. Unfortunately, the three-dimensional problems of complicated boundary conditions are beyond the existing analytical methods. The three-dimensional finite element method (FEM) was therefore employed in this study. In the analysis, square pillars of 40 feet wide and an entry height of 8 feet were assumed while entry widths varied at 14, 20 and 26 feet. This model was selected to simulate the mine where roof falls data were collected. The second phase of the study was the collection of field data. The sizes of the roof falls including heights, lengths and widths were collected and analyzed. In the third phase study, the results of the first and second phases were compared and discussed. The analysis of field data revealed an arching zone within which roof falls occurred. The arching zone above an entry obtained empirically was compared with the calculated stress contours. Assuming that the bolts must be anchored in the rock strata outside the arching zone, the preferable systems of bolting were proposed. Also the amount of pretension required to inhibit sliding between layers was discussed.

Jan 1, 1978

By Bruce Watzman

"Few issues are more important to the National Mining Association (NMA), the U.S. mining industry and NMA’s MINExpo International 2016 exhibitors than safety.Global mining safety and health is a journey necessitating continuous improvement, collaboration and innovation on the part of both mining operators and their suppliers.MINExpo 2016, which takes place Sept. 26- 28, 2016, in Las Vegas, provides attendees with the opportunity to view technologies to help refine management of mining safety and health, utilizing NMA’s CORESafety system. CORESafety ‘One of the best’Launched by NMA in 2011 and moving forward ever since, CORESafety is driving continuous improvement in safety and health performance among participating industry companies by shifting from a command-andcontrol regulatory approach to a risk-based systems approach built on the Plan-Do-Check-Act model (Fig. 1).Considered an exemplary safety and health management system, NMA’s CORESafety system helps mining operators change their approach to safety and health management by enhancing the safety and health culture throughout their organizations. Although it is challenging to consistently and completely control all the factors and variables occurring in daily mining operations, experience has shown that applying systematic controls to as many variables as possible is the most successful approach for improvement in mining safety and health.When embarking upon the development of the CORESafety framework, NMA’s leadership set an ambitious goal to eliminate fatalities and reduce the injury rate 50 percent in five years, or the “0-50-5” goal. While the goal has not been met yet, the steady progress has been extraordinary with fatalities among participating companies dropping 45 percent during the period 2011-2015 (Fig. 2). Data also demonstrate that, as participating companies increase their level of implementation, total injury rates have also declined (Fig. 3).In a September 2015 interview with NMA, Penn State University mining engineering Professor Jeffrey Kohler praised CORESafety as “an inspired and timely program that brings together key elements to achieve safety and health goals.”"

Sep 1, 2016

By D. Malhotra

The number of variables which can effect flotation of molybdenite is very large. This paper discusses the effect of two operating variables, namely, the degree of aeration and agitation, on the grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." The analysis of flotation results indicate that molybdenite can be characterized into fast-floating and slow-floating components. The rates of fast-floating components, which do not create a problem in flotation, could be varied by changing agitation of airflow rates. However, the rate of slow-floating components was stable and was only a function of residence time in the float machine. The degree of aeration has a significant effect on the grade of MoS2 with only a slight effect on the recovery of MoS2. The degree of agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits is subsequently discussed.

Jan 1, 1977

By M. S. Celik

Beneficiation of boron minerals by flotation with well defined systems has been very little investigated in the literature. The difficulty arises from the fact that boron minerals cover a spectrum of solubilities. Colemanite, a calcium containing relatively insoluble boron mineral, and borax, a highly soluble boron mineral have been used to exemplify the flotation of boron minerals. The floatability of both minerals using sodium dodecylsulfonate and dodecylamine hydrochloride exhibits considerable differences in their response to flotation. This has been ascribed to variations in the solubilities 0f boron minerals and the presence of the cations in the lattice structure. Flotation tests along with zeta potential measurements are used to elucidate the mechanisms involved in the flotation of boron minerals.

Jan 1, 1992

By William Gleason

The Society for Mining Metallurgy and Exploration (SME) has a long and proud history of being the world?s leading resource for the dissemination for technical information regarding the fields of mining and mineral extraction and processing. That reputation was met, and maybe even exceeded, with the programming for the Society?s 2014 Annual Meeting in Salt Lake City, UT Feb. 23-26. The meeting drew more than 6,700 attendees to the three-day conference that featured more than 90 technical sessions with 670 presentations. These sessions covered the breadth of the mining and minerals industry, but it was the so-called ?softer issues? that were discussed in the keynote session that kicked off the meeting. The keynote session, ?Community Engagement: Building Partnerships for Mining,? brought together some of the leading voices from the mining industry, as well as some of the top voices from nongovernmental organizations (NGOs) that work in the mining sector. The common ground between the panelists was their dedication to working to ensure a social, economic and environmental balance in the development of mines. ?We wanted to bring these NGOs in to begin a dialogue to see how we can work together,? said SME President Jessica Kogel. ?This is a space that SME has not typically operated in, but one in which SME can bring a technical, scientific voice to the discussion. SME wants to play a leadership role in creating partnerships between the technical, social and economic areas that are crucial to the success of any mining project.? In today?s environment, finding mineral deposits and extracting the minerals in an economically viable manner is just one piece of an increasingly complex puzzle. Earning and maintaining a social license to operate requires careful consideration of local and global impacts. The industry often comes under intense scrutiny when a new project is proposed and, therefore, it must strive to meet the highest ethical and environmental standards. Success requires cooperation and collaboration between the industry, community and NGOs.

By M. J. Klishis

This paper presents the findings of a study on roof bolters' hazard exposure. A "micro-analysis" of accident data was combined with ergonomic observations of roof bolter operators to categorize bolting-related injuries and a checklist was constructed. Bolting-related problems were identified as situations that could expose bolter operators to hazards. Approaches to avoid these situations were applied at six mining operations to evaluate specific problems in roof bolting operations. The re-search emphasized the importance of analyzing worker behaviors in the context of mining situations and equipment design problems that lead to human error accidents.

Jan 1, 1995

By Patrick G. Hatcher

Studies of sedimentary humic acids by nuclear magnetic resonance (NMR), stable isotopes, and elemental analysis show they are derived by oxidative degradation of complex plant macromolecules that are insoluble in aqueous or organic solvents. The mechanism by which humic acids originate is fundamental to our understanding of the role of organic matter in ore deposition, because these substances can complex and mobilize a number of metal ions. The organic matter associated with uranium ores of the San Juan Basin, New Mexico and Carlin-type disseminated gold deposits of Nevada has certain organic geochemical characteristics that suggest an origin from humic acids.

Jan 1, 2013

By Haydn H. Murray

The area from Ohio on the east, Tennessee on the south, and Minnesota on the west: contains some very unique and useful clay deposits. Included are fireclays and plastic clays in Ohio, Kentucky, Indiana, Illinois, and Missouri; flint clays in Kentucky and Missouri; ball clays in Kentuckv and Tennessee; adsorbent clays (fuller's earth) in Missouri, southern Illinois, and Tennessee; and alluvial clays and shales for structural clay products from every state. Unique kaolin clays are known in Minnesota, Missouri, and southern Illinois and halloy-site localities are known in southern Indiana. The geology, physical properties, and uses or potential uses of these midwestern clays are described.

Jan 1, 1980

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, Y. Xiong, J. Gu

"As ores degrade, mining techniques and chemistries change to meet market demand and maintain product quality. The balance of recovery and grade is a significant challenge in the Crago Process where an anionic collector is used to float phosphate, followed by acid scrubbing, then an amine float to improve product grade. As the grade is a requirement for DAP and MAP production, recovery is the criteria to suffer. Phosphate losses in the amine float can bring overall recovery down by as much as 18%, creating a growing need to think outside the box to improve recovery. This paper will focus on the theory of amine tail recycling and the best methods to optimize the overall phosphate recovery by recycling the tails from the cleaner flotation step. INTRODUCTION In 2014 the total US phosphate production was down 13% over the prior year, from 31.9 to 27.1 Mt, which accounts for 12.32% of the world’s phosphate rock production. Florida and North Carolina phosphate production accounted for 80% of total US phosphate production, which was down from 85% the previous year. This decline is due in part to the closing of the last phosphate mine in Polk County, FL - which had an operating phosphate mine for over 100 years (Gurr, 2015). Another factor contributing to the reduction in contribution from FL & NC is the increasing challenges in beneficiating the remaining ore deposits. The Central Florida mining district has historically been in the Bone Valley deposit, where raw apatite was abundant with P2O5 values as high as 15%. The Bone Valley ore also had characteristics favorable to beneficiation to 27.5-29.7 %P2O5 while achieving recoveries above 86%. The move southward into the Hawthorne Formation has seen the ore feed grade hit some historic lows, and the matrix characteristics pose more challenges to phosphate producers. The Hawthorne Formation experienced lateritic weathering after the Bone Valley formation which altered the apatite to aluminum phosphate minerals, and alteration of montmorillonite to kaolinite, releasing MgO that caused the dolomitization of the top of the Hawthorne limestone (Cathcart, 1966). Elevated levels of dolomite can yield an increase in slurry viscosities, reduce production rates, and increase energy costs in the wet-acid fertilizer process. The MgO will also act to dilute grade, making it more difficult to achieve a standard 18-46-0 product (McHardy, 1981)."

Jan 1, 2016