Search Documents

By Gary G. Grim

The reliable performance of the coal reclaim system is essential to the continued availability of a coal-fired electric generating unit. The control of fugitive coal dust within the areas housing the reclaiming equipment is necessary not only to minimize maintenance and clean-up costs, but is also a safety and health consideration. This paper describes the reclaim system control and dust suppression systems as initially installed, the shortcomings of these systems and the steps eventually taken to correct these shortcomings.

Jan 1, 1983

By M. P. Corriveau

This is the case history of how two nearby plants in Southwest Virginia solved their water clarification problems. While the solutions should not be considered applicable industry-wide, the methods used in arriving at the answers deserve consideration. When Clinchfield's Moss No. 2 Preparation Plant, the first ever built in Tiller Seam coal, was started in the fall of 1956, the clays in the raw coal soon posed a flocculation problem, Laboratory sedimentation tests were initiated; and as a result, lime was adopted as the flocculant for the clays, With lime, a pH of 11.2 was required. As the plant tonnage increased, it became evident that the amount of coal fines produced in the mining and preparation was greater than had been estimated and that the 90-foot thickener was inadequate in providing sufficient settling time to effect a clarified overflow for reuse. Testing showed that Separan 26105 (NP10)1/, when used with lime, was the most satisfactory coal flocculant available,

Jan 1, 1960

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By M. L. Rizzone

Since time immemorial, Mother Nature has been transporting slurries with both air and water serving as the carrier medium. Consider for example the formation of the continental shelves off our coast lines which are being formed by rivers emptying erroded land surface and depositing it into bays and gulfs. As the erosion processes take place, the fines are suspended in water which flows in streams and rivers and deposits where the velocity of the flow reduces sufficiently to allow the fines to settle out. The same process in some crude form is provided when one hoses his driveway or patio and moves dirt so as to provide a cleaning action. These examples illustrate rather crudely how the formation of slurries allows for the transport of solids. In recent years, this mechanism has become fairly well understood and slurry pipelining of many materials is now a vivid reality. The movement of liquids in pipelines necessarily occasions the use of pumps for the purpose. Those of us who have had some rub with the petroleum industry are familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well the circulating fluid utilized to remove chips which are cut by a drill bit from holes drilled deep in the earth is called drilling mud. This substance contrary to what the name might imply is usually a fairly sophisticated material designed to develop certain characteristics which are desirable in the drilling process. The particles which have been cut by the drill bit are suspended in the moving column of fluid and brought to the surface and deposited. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits. However, it is impractical to remove the fines completely from the drilling fluid and as a result they are pumped through the mud pumps back into the circulatory stream.

Jan 1, 1969

By Paul I. Eimon

Mineral exploration involves the selective collection, organization, evaluation, and interpretation of geologic and economic data. The sources for such data are original field observations and existing documented information of various types (publications, reports, maps, company files, etc.). As exploration data are accumulated, their storage, organization, indexing, and J retrieval is key to exploration progress. Initial use of computers by mineral exploration groups indicates that data can be meaningfully handled by machines. A computer system makes possible: 1) the storage, manipulation, collation, and selective retrieval of data; 2) the utilization of data banks developed by geologic service groups and available at relatively low cost; and 3) the retrieval of stored data more rapidly, completely, and effectively than by manual systems. Profitable utilization of these capabilities is conditioned by several factors, particularly by the information selected for the system data base and by the design of the computer system itself.

Jan 1, 1968

By Donald V. Fites

The evolution of open-pit mining has been rapid during the last two decades. The development of larger, more productive and efficient equipment has been one of the key factors in this open-pit advancement. Selection of the proper equipment and its correct usage is paramount to successful operation while maximizing return on investment. The quantity of material being moved prior to mining the saleable product is increasing at a significant rate. For example, at a southwestern copper mine more than two hundred million tons of over- burden have been removed prior to exposing an ore which contains less than 1% copper. A recent survey of twenty-three Western Hemisphere copper mines reveals the average strippingratio was 2.2:l with a range of 0.9-8.5:l. In the face of increased mineral demand, the resulting technological developments and rising overburden to ore ratios, many open-pit mines now use totally different concepts for the removal of ore and overburden. An increasing number of these concepts now being installed include wheel tractor scrapers as a major part of the material handling system for unconsolidated overburden removal. To say scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. As reported in the Minerals Year- book, however, about one-half of the material moved in metal and non-metal mines is never drilled and blasted or broken by other means. We will, therefore, in this paper, concentrate on the role of wheel tractor scrapers in unconsolidated overburden; the area of greatest usage.

Jan 1, 1969

By A. E. Kurie

The Great Salt Lake occupies about 1000 square miles whereas its predecessor, Lake Bonneville occupied 20,000 square miles and its shoreline reached 1000 feet above the present lake level. The sediments of Lake Bonneville range from peripheral gravel and sand deposits to central basin calcareous clays and silts, gypsum sands, and saline precipitates. The drilling and engineering tests conducted by the Utah State Department of Highways for many highway structure sites and the construction of Federal Interstate freeway provided engineering and hydrologic properties of Lake Bonneville sediments. Ground water and surface brine exploitation have contributed hydrologic and chemical data; the geologic and mineralogical data are scientific research contributions.

Jan 1, 1967

By Adrian Molinari

A radioisotope probe (Minexan 202) capable of simultaneously analyzing a mineral slurry for five elements and pulp density has been developed by Outokumpu Oy, Finland. The probe is designed to operate immersed directly in a process stream, or it can be equipped with a flow cell through which passes a continuous sample of the main stream. A minicomputer (PDPII) is used to control the probes and calculate the assay data. This paper describes the probe as applied to slurry analysis and compares it to the conventional x-ray on-stream analyzer (Courier 300).

Jan 1, 1977

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By Christian F. Baiz

The author will present a discussion of the steps which must be taken by the prospective developer of a small mining operation to establish technical credibility when seeking financial backing. Particular emphasis will be given to the differing levels of technical work (and their relative cost) which must be accomplished to supply the information necessary to satisfy potential investor groups, whether they be other mining companies, equity investors, or financial institutions such as venture capital firms or commercial banks.

Jan 1, 1981

By George W. Bain

Deposits of metals in only slightly disturbed strata have been attributed to sedimentation processes contemporary with deposition of the strata. Recently this origin has been extended' to a greater variety' of deposits and local enrichment has been attributed to selective remobilization of metallic minerals in the host stratum. Effects attending metallization and deformation, and exact age' of the metallization are compiled to establish the sequence of events in ore deposit histories in order to clarify importance of remobilization within a formation relative to introduction from an outside source into an fav¬orable host. The pertinence respectively of deposit; origin and geometry to the work of the mining geologist is reviewed. Dwarf faunas in the Clinton iron ore, Tully pyrite bed and Rammelsberg deposit, indicate abnormal metal ions in the sedimentary environment. Slight¬ly disturbed strata are host rocks in the Swedish Kolm, Timna, Kupferschieffer, and White Pine deposit; the latter two have ore only in conjunction with tectonic structures.

Jan 1, 1966

By F. Ikumapayi

In order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the influence of major species, calcium and sulfate in process water on sphalerite flotation was investigated through Hallimond tube flotation, zeta potential, diffuse reflectance Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements using sphalerite mineral sample. Assessment of process water species in flotation was done using deionized water, process water and simulated water containing calcium and sulfate ions in experiments. Hallimond flotation shows increased sphalerite float-ability in process water compared to deionized water, but no significant effect on the presence of calcium and sulfate ions in deionized water using isobutyl xanthate as a collector. The presence of calcium ions reduced the sphalerite?s negative zeta potential, while at higher concentrations, a charge reversal occurred, at about pH 11. FTIR and XPS studies revealed the presence of surface-oxidized sulfoxy and carbonate species on sphalerite at pH 11.5 in deionized water, process water and water containing calcium and sulfate ions. These surface species do not influence xanthate adsorption.

By J. S. Whatley

The properties, origin and industrial uses of kaolin clay are briefly reviewed. The general waterwashed beneficiation process is described. Yost aspects of filtration and solids-liquid separation as practiced in the kaolin industry are mentioned along with devices that are currently in the developmental stage. The paper focuses heavily on the well known art of rotary vacuum filtration, including general construction and operating details. Devices under investigation that might be used to mechanically or electrically dewater clay slurries to higher cake solids levels than can be achieved with rotary vacuum filters are described briefly.

Jan 1, 1986

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979

By John S. Cummings

Although there are many geologic situations which might be discussed at a session such as this, as I considered the problem, it became apparent to me that I should discuss a situation which has been of concern to me, and should be of concern to the geologic community. As a result, the questions which I will pose, and the criticisms, have not been arrived at quickly or easily, but have accumulated through time, to the point where I feel discussion is necessary. Very briefly let me say that my criticism of geologic mapping, of conclusions reached, and objectives or lack of such, results from my association with many areas where such studies have been completed, and resultingly my inability to comprehend the system of evidence or logic which supports extensive age-formational designations. The heart of the problem is that many conclusions resulting in geologic designations are based on weak or non-existent evidence, and such should be catagorized as hypotheses. Although the geologic community as a group does not approve or disapprove of such designations, it is evident that many or most of such designations attain a "status", and arc accepted as more or less valid statements. As will be shown, the amount of specific lithologic data provided in some quadrangle mapping projects is exceedingly slim. However, of concern herein is that the type of information presented at any stage is sufficient to warrant conclusions drawn. To see the magnitude of the problem, it is probably necessary to review some basic fundamentals upon which our geologic systems are established. The United States Geological Survey has defined a "formation" as the broad unit of geologic mapping consisting of a large and persistent stratum of one kind of rock. Obviously such a designation allows that a formation could be considered "time variant" in a horizontal as well as in a vertical context. However, other definitions enable a formation to mean units

Jan 1, 1972

By B. Pesic

Manganese is about twelfth in the list of the most abundant elements in the earth's crust (Reidies, 1981). More than 150 known minerals contain manganese as an essential constituent (Mellor, 1932). In general, ores containing at least 35%Mn are classified as manganese ores, ores with 10-35%Mn are called ferroginous manganese ores, and ores containing 5-10%Mn are known as manganiferrous ores. One very important class of manganiferrous ores are manganiferrous-silver ores. They occur in the oxidized portions of the silver deposits of the Western United States. Silver is very often associated with manganese oxides which in some ore deposits are dispersed through calcite, causing the black color of the host rock, which is known as black calcite. Black calcites can occur in carbonate rocks (10-1500oz Ag/ton) and in volcanic rocks (less than 1.0oz Ag/ton).

Jan 1, 1986

By W. C. Brice

Minnesota contains a major copper-nickel resource. In anticipation of requests by industry to develop this resource, the Minnesota Department Of Natural Resources has developed a computerized resource inventory and analysis system, MINESITE This extensive database is available to regulatory agencies as they evaluate mining proposals as required by law. The Resource Analysis phase of the project allows state mining policy decisions to be evaluated in terms of long-range effects on Minnesota's mining industry and environmental and land use impacts. The analysis also allows for comparison of proposed mine facility sites to a representative range of sites in terms of engineering, site characteristics, and land use and environmental impacts.

Jan 1, 1980

By E. C. Winegartner

In producing and selling coal, the coal company is faced with many different parameters by which the quality of its product is evaluated. One type, which we choose to call the economic parameters, includes moisture, ash, sulfur, and Btu's. These are reasonably well understood by both the coal supplier and the customer, and the dollar values can be placed on them. This is the group of parameters of primary interest to most purchasing agents buying coal. A second group of parameters governs how the coal will behave in the boiler itself and is of primary concern to the engineers designing the boiler and to the men who must operate and maintain it. Since we have not yet learned to put dollar values on these parameters, they generally show up in coal contracts simply as cutoff points, the purchaser simply saying that he will not accept coal outside of certain limits.

Jan 1, 1975

By J. K. Whyatt

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations of in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence from the Lucky Friday Mine collected by U.S. Bureau of Mines researchers, as well as a review of case studies, demonstrates that in situ stress variations affect the spatial distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies, they are too expensive and, depending on conditions, may be too difficult, to use routinely in mapping stress variations. However, information from borehole and raisebore breakouts; deformation of mine openings; and patterns of seismicity, ground control problems, and rock burst damage can be used to build a stress database. This database can then be used in con-junction with maps of mine structure and geology and models of rock mass behavior to build a map of in situ stress variations. Such a map provides a means to anticipate patterns of mining-induced seismicity that are likely to be encountered and, hence, provide a means for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1995