Search Documents

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

By John Reilly

Traditional methods of project procurement of have remained virtually unchanged in the U.S. infrastructure construction industry for more than 50 years. The traditional method, Design-Bid-Build (DBB), uses a two-step process that separates planning and design from construction. Design is generally done by the public agency and their consultants and the subsequent construction contract is procured from the private sector, almost always by a “low-bid” approach. This method has worked well for many projects, delivering quality work for the lowest bid price. This is particularly true for those projects where the work, and the public agency’s management procedures, are well understood by the contracting community and there is relatively low uncertainty in the work or conditions, particularly geotechnical conditions for underground construction. However, concerns exist with the DBB process. It is time consuming because all planning and design work must be completed prior to beginning any construction work and it is of concern for complex or large projects, plus those with significant risk, where the separation of design and construction, in conjunction with pressures resulting from the low-bid environment, often result in substantial cost and schedule increases. Frequently, these increases occur in a non-productive, inefficient, adversarial work environment leading to claims, disputes and costly litigation (Quick 2002).

Jan 1, 2007

By M. J. Farrell

The threat of global warming and its prominent position in public discussion and political debate requires all industry to take stock of its contribution to rising atmospheric concentration of greenhouse gases. For the primary metals industry, the first step must be to identify the pattern and range of emissions at each step in the production chain. Only then can the industry assess the economic consequences of the penalties on emissions that will be imposed by governments and regulators and devise cost-effective plans to avoid or mitigate such penalties. While some work has been done to estimate carbon dioxide (CO2) emissions using Life Cycle Inventory analysis, this approach is less useful than site-by-site emissions estimates. It is the level of specific emissions at each site that will ultimately deter-mine carbon taxation liabilities and participation in emissions trading schemes. Most mining companies have moved with the times to issue sustainability reports for their operations. But in the absence of any standardized reporting format, it is difficult to make useful comparisons between even the best-reported producers on a like-with-like basis. For this reason, Minecost.com modeled the use of fuels and energy used in mining, milling, shipping and metallurgical treatment to cover ?cradle-to-gate? emissions of greenhouse gases resulting from the production of the major base metals copper, zinc, lead and nickel. Greenhouse gas emissions ? overwhelmingly carbon dioxide ? are associated with the consumption of energy at every step in the production chain, from exploration through mining to the production of refined metal. Producers of primary metal employ diverse technologies to mine, mill, smelt and refine several different types of ore. Every orebody has its own special characteristics. In addition, most base metals are produced in concentrate that must be transported to smelters, with con-sequent emissions consequences.

Jan 1, 2009

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By John Addison

Experimental animal studies comparing asbestos and non-asbestos varieties of tremolite indicate tremolite asbestos is markedly more carcinogenic. By direct analogy, the differences in carcinogenicity between tremolite asbestos and non-asbestos prismatic tremolite should be the same for the other types of amphibole that also crystallize in the asbestos and non-asbestos habits. The earliest of the experiment animal studies, done more than 25 years ago, have design limitations by modern standards including the use of injection or surgical implantation as the route of administration rather than the more relevant route of inhalation. However, the differences in the carcinogenicity of amphibole asbestos and non-asbestos amphiboles are sufficiently large to be clearly discernable even with the study limitations. Together with later studies on these and related minerals, there is strong evidence of a much lower hazard associated with the shorter, thicker fibers of the non-asbestos amphiboles, than is found for the asbestos analogues of the same mineral. It is possible that the non-asbestos amphiboles are no more hazardous than other silicate minerals widely considered nuisance dusts. © 2007 Elsevier Inc. All rights reserved. Keywords: Amphibole; Asbestos; Tremolite; Carcinogenic

Jan 1, 2007

By D. J. Gilbert

As a preventive action, the geotechnical department at the mine analyzed the original topography overlying a conveyor tunnel at the mine. Several dewatering drains were installed to intercept water collecting from an old lakebed. Subsequently, 20 steel arches were installed to provide additional support in an area of tunnel where original geological mapping indicated Type IV rock. This project was completed ontime with no loss to production. Construction schedules had to be developed to half hour precision, to accommodate the installation.

Jan 1, 2011

By M. Rufli

Until not so long ago most ring geared mills were operated with fix speed motors only. By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The sophisticated operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore utmost availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives. Now this paper is focusing on the experiences gained with this kind of sophisticated ring geared mill drive system rather than only show and explains the operational benefit of the different functions. Several measurements of different operating conditions, starting, frozen charge remover, controlled roll back, backlash, etc., made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. The accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.

Jan 1, 2011

By David L. Veith

As the basis for the State of Minnesota's Regional Copper-Nickel Study environmental evaluation, hypothetical mine models were developed ranging in ore capacity from 5.35 to 20.00 x 106 mtpy. Open pit and underground mining operations were defined utilizing conventional methods of ore extraction. Processing of the copper-nickel sulfide material involved conventional bulk flotation of the valuable minerals, with maximum water recycle And tailing disposal. Flash smelting and electrolytic refining of the concentrate resulted in 0.10 x 106 mtpy copper plus nickel metal, plus associated cobalt and precious metals. Variations in model parameters allowed environmental trade-offs to be identified.

Jan 1, 1980

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By C. O. Brawner, J. Kalejta II

The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than about 45°. As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result with less rock fall capacity. The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented.

Jan 1, 2002

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mud-stoneovercored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2000

By Brett Zernich, Michael Krulc, Brett Robinson

This paper provides an account of the efforts undertaken to construct the Northeast Interceptor Sewer (NEIS) project, which is a portion of a much larger program in Los Angeles, California to upgrade the city’s wastewater facilities. The project consisted of a number of elements, including both soft ground and rock slurry wall shafts, drilled shafts, soft ground EPBM mining, rock TBM mining, large diameter pipe placement, and underground structure construction. The need to complete the project under strict schedule constraints, in addition to the challenges of underground construction in congested urban areas, necessitated the work be undertaken with the proper balance of state of the art equipment, and thoughtful planning. The paper will detail the means, methods, and equipment used on the project, as well as discuss several of the unforeseen conditions encountered during construction.

Jan 1, 2005

By B. Gigas, M. Preston, M. Giralico

Optimized mixer settler designs will now handle total flows of over 6,000 m3/hr.Computational Fluid Dynamics (CFD) is a timely and predictable tool for design development. Lightnin has the capability of using numerical analysis methodology to evaluate flow patterns and phase separation. CFD can show performance differences between changes, in mix tanks, in settler geometry, and in liquid depth, against variable flow rates. Understanding the differences allows the development of optimized designs. This paper focuses on the major design components of the mixer settler and how technological advances will lead to further improvements, when designing for today’s largest flow plants.

Jan 1, 2004