Search Documents

By G. Konstantopoulou

Environmental degradation due to abandoned quarries is an international problem, more intense when these sites are found in urban or suburban zones, in environmentally sensitive areas or are visible from sites of special interest. Rehabilitation solutions applied worldwide, range from simple relief restoration and planting to more sophisticated site exploitation in order to serve specific social needs. The elaboration of rational rehabilitation plans for every site presupposes deep knowledge and comparative evaluation of all the parameters of the problem. In this paper, a methodological approach of rehabilitation solutions for abandoned quarry sites is elaborated, based on domestic and international experience and practice. Solutions are grouped in eight main categories. In every category the framework of prerequisites and confinements (environmental, technical, social, economic, legal) for their application in Greek quarry site is investigated. A comparative assessment of alternative restoration solutions is introduced, using tools supplied by environmental economics, cost-benefit analysis, G.I.S. and multi-criteria analysis and follows in two stages: 1) Establishment of a set of criteria aiming at a priority list for a number of quarry sites located in a geographical or administrative district. 2) Assessment of alternative solutions for every single quarry from the previous priority list for the selection of the most adequate using technical, economical, social and environmental criteria.

Jan 1, 2008

By W. J. D. Stone

Many of the common valuable minerals have a magnetic susceptibility which is sufficiently high to render them amenable to magnetic separation. In addition,, many minerals which form the unwanted constituents of an ore can be removed by magnetic means. Magnetic separation in general has suffered seriously from, the lack of a high intensity wet separator. It is only recently that such a separator has become available to the industry. Prior to this, high intensity magnetic separation has been limited to the use of the dry techniques. Since the introduction of the Jones Wet High Intensity Magnetic Separator, extensive test work has been conducted to investigate possible applications. From the investigations conducted and the discussions that have taken place in the industry, it is apparent that the important mineral characteristic of magnetic susceptibility is not receiving the attention that it deserves. Applications for high intensity wet separation are being found in areas hitherto not considered.

Jan 1, 1963

By Y. Lv, H. Ye, D. Du

Electrolytic manganese residue (EMR) is a kind of industrial solid waste with high silicon content that contains harmful metal elements such as chromium (Cr), copper (Cu), lead (Pb), cadmium (Cd), nickel (Ni) and cobalt (Co). Developing a highly effective and environmentally friendly process to treat EMR is important, both for the reutilization of metal resources and for environmental sustainability. In this study, the bioleaching of available silicon from EMR using silicate bacteria is investigated, with flask experiments conducted to optimize the parameters in the bioleaching system. For metal ions, the concentrations of manganese (Mn), Co, Ni and Pb in solution were measured to determine the environmental safety effects before and after bioleaching. The results show that the bioleaching rates of available silicon in the slag were mainly affected by the temperature, pH and pulp density. Under the optimal conditions of temperature of 30 °C, pH of 7.0, pulp density of 5 percent, shake flask rotational speed of approximately 210 rpm, particle size of approximately 0.150 mm and leaching time of 16 d, the concentrations of available silicon in the bioleaching system rose to approximately 110 to 140 mg/L. The metals remaining in the residues were mainly bonded in stable fractions, with concentrations lower in the leachate after bioleaching. This study demonstrates that silicate bacteria can be used to increase the contents of available silicon from EMR, and that bioleaching technology can realize the harmless resource utilization of EMR.

"A fire design innovation of the concrete lining of the Ohio River Bridges East End Crossing Tunnel has been developed. As a result from a fire suppression and tunnel ventilation system, the project design Heat Release Rate (HRR) was able to be constrained from 300 MW to about 50 MW. With this reduced HRR, concrete lining without passive fire protection may be acceptable, if the tunnel concrete lining will not result in explosive spalling during the designed fire event. Concrete explosive spalling test was proposed to verify this assumption. Since no standard concrete fire explosive spalling testing procedure exists, a project specific testing procedure was developed and fire tests conducted. From fire test results, it is concluded that the proposed tunnel concrete lining, in conjunction with the proposed fire suppressing and ventilation system, will not experience explosive spalling and does not require a passive fire protection system. INTRODUCTION The Ohio River Bridge East End Crossing Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The Tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining consists of 16 inches cast-in-place concrete lining and 20 inches invert slab, with a waterproofing system around the tunnel perimeter. Two (2) tunnel side drains and one (1) invert drain were provided for each tube. This paper describes the rational in assessing fire design requirements of the tunnel final concrete lining, to answer the question whether a passive fire protection system is needed or not."

Jan 1, 2016

By Jeremy Cawley, Horry Parker Jr., Clint Wilson

The 5180 m EPBM drive on the Lower Olentangy Tunnel (LOT) is predominantly within glacial overburden. To connect LOT with the existing OARS deep tunnel in limestone bedrock, the upper 15 m inside diameter Vine Street retrieval shaft telescopes down to 6.7 m in diameter and extends into the karstic Columbus Limestone to a depth of 51 m, where a 104 m SEM tunnel will connect to OARS shaft 6. Pre-excavation grouting was reuired prior to lower shaft excavation to reduce potentially high groundwater inows. This paper discusses the secant pile installation, grouting program, shaft excavation, and hydrogeologic observations.

Jun 23, 2024

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992

By Ashraf A. M. A. Wali

Many of the economic resources of Egypt have been recognized and exploited for thousands of years (e.g. gold and copper). Most of these minerals, particularly those from hard-rock sited deposits, are found in complex form along with other components while those present in sedimentary sequences are largely in simple compounds or as native elements. Recognition of their characteristic settings (structure, basin development, environment of formation etc.) is the main clue in predicting and locating their presence. The main economic minerals exploited in Egypt today come from sedimentary sequences and include sodium and potassium chlorides, gypsum, sulfur, and sedimentary iron ores. Large amounts of low grade sedimentary phosphates are known but are not of economic value at today's prices. Recent intensive investigation in the north-eastern Sinai (EI Arish) and along the southern coasts of the Gulf of Suez has revealed new and extensive sulfur and chloride deposits, and considerable oil and gas are now being exploited from closely related sediments. Tin is the only mineral that is produced from hard-rock sources, and gold and copper deposits are present but not of high enough grade to be economically viable. However, a significant part of Egypt has not yet been studied in enough detail to close the door on future discoveries. Another point of considerable geological interest is the presence of diverse, modern evaporitic settings, from which we may draw the analogs for many of the older gypsum, anhydrite, chloride and sulfur de-posits. In fact these analogs are so well displayed that both the Sinai and Gulf of Suez-Red Sea evaporites (Middle and Upper Miocene) can be readily compared with these modern deposits.

Jan 1, 1990

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology's Process Insights neural network software and Oil System's PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995

By Stephen Semeniuk

Working with junior mining companies as a valuer, my experience with regulators is that simplicity works and the sales comparison method is the way to go. What I like about Mr. Ellis?s approach (as in his Table 7) is the integration of commodity prices with the timing of acquisitions and the implication of price changes in gold on the adjustment of individual project valuations. However, the sample gold-related appraisals in Ellis?s paper are pre-2008 transactions and readers should be made aware of the current market for such projects. Before moving on, to be noted is that the effective date of the Las Brisas appraisal (Ellis?s sample Appraisal 3) is Feb. 10, 2006; given that the subject value of Transaction 9, Choco 10 in Ellis?s Table 6 was listed as $353 million for a 95% interest in the con-cession, I am uncomfortable accepting that the acquisition was suddenly worth the adjusted value of $1,205 million (as given in Ellis?s Table 7). In some cases, illiquidity discounts can apply, and commodity-wise, in the one-month period between the acquisition in January 2006 and the adjustment to the Las Brisas conditions as of February 10, 2006, the indicated gold price change was only 41 cents/g ($12.60/oz); i.e., from $17.50/g to $17.91/g ($544.40/oz to $557/oz).

Jan 1, 2012

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By Evan J. Owen, Virginia T. McLemore

of high specific gravity, resistant minerals that form from mechanical concentration by waves, currents, and winds in marginal-marine environments. These sediments are enriched in critical minerals such as titanium, zirconium, and REE. Cretaceous beach-placer sandstones are found in the Colorado Plateau of northwestern New Mexico. Originally discovered by airborne radiometric surveys for uranium in the 1950s, these beach-placer sandstones are being re-examined with modern methods as potential sources for critical minerals. Selected beach-placer sandstones have been sampled, mapped with ground radiometric surveys, and analyzed with whole-rock and trace element geochemical methods. Mineralogy is being determined with optical methods, XRD, and EMPA. Zircon, rutile, ilmenite, and monazite are the primary heavy minerals of interest found in the studied deposits. Initial results show that the sandstones contain up to 1.4% total REE, 29.4% TiO2, and an estimated 4.9% ZrO2. Chondrite-normalized REE diagrams show distinct light REE and minor heavy REE enrichment, as well as pronounced negative Eu anomalies for each deposit.

Feb 1, 2024

By W. G. Kegel

The past few years have produced a rash of demands for changes in America's way of doing things. From manufacturer to consumer, the rules have been changed. Some of the demands were needed and, when legislated to requirements, did manage some good for all concerned. Other demands made by zealots and taken up by regulatory agencies have forced costly changes on our way of life. No segment of industry has been exposed to more new rules and regulations than the deep coal mining industry in the United States. There is no denying that some good has evolved, but most mining men know that the effects have done more to reduce production and increase cost than they were ever intended to do.

Jan 1, 1975

Ventilation 'is currently used in mines to sustain human life, prevent explosions, and provide a more healthful work place. Future automated-mining systems could use ventilation techniques quite. different from today's practices. The Bureau of Mines is anticipating various methodologies for ventilating the automated mining systems which are now beginning to emerge in the mining industry. This paper examines the special ventilation requirements for automated mining systems. Topics include requirements for automated systems, current studies with blowup ventilation tubing, and ventilation of two types of highwall -ripper type mining machines.

Jan 1, 1990

By Jey K. Jeyapalan

A characteristic common to most tailings dam failures caused by earthquakes or excessive rain storm is that the tailings tend to liquefy and flow for substantial distances as a viscous fluid, with the potential for extensive damage to property and life. Failures of El Cobre, Chile (1965), Mochikoshi, Japan (1978), Aberfan, Wales (19661, Buffalo Creek, West Virginia (1972) are examples of such catastrophic incidents. In these four incidents more than 400 lives were lost, and the loss of property was approximately $200 million. In order to be able to assess the potential for damage in case of such a failure, it is necessary to predict the possible extent of flow slide movement. This paper discusses simple procedures for performing such analyses. Also, in order to illustrate the use of these analysis procedures in tailings dam design, two case histories are analyzed.

Jan 1, 1982

By M. K. Larson

"Specialized numerical modeling codes have been developed over the years to estimate ground stresses during the excavation of coal in underground mines. One of these tools, MULSIM, a displacement discontinuity boundary element code, was last developed by Zipf into a version called MULSIM/NL [USBM 1992a, 1992b]. The code was used frequently in years past, but closure of the Bureau of Mines in 1996 marked the beginning of a pause in its development. A similar tool with distinctly different treatment of overburden idealization, LaModel, was subsequently developed [Heasley 1997] and largely displaced MULSIM/NL in the literature. However, recent work modeling deep western longwall coal mines [Larson and Whyatt 2013] has demonstrated that MULSIM has distinct advantages for regions with relatively stiff and strong overburden. This work required that MULSIM be revived and updated into a version called MulsimNL/Large. Updates include larger array sizes, greater precision, greater number of materials, and the addition of a five-point, six-segment pillar load/displacement model that provides the user a more flexible coal-strength model allowing hardening and softening before a final residual strength. MulsimNL/Large has the ability to calibrate to large load transfer distances observed in some western U.S. coal mines that appear to be caused by strong, massive units in the overburden and/or floor of a coal mine. Also, it provides the ability to calibrate gob stiffness to simulate measurements or estimates of overpanel weight distribution between gob and abutment, while still maintaining load transfer distance with minor adjustments. MulsimNL/Large can easily implement material strengths calculated from various pillar strength models. The five-point model gives MulsimNL/Large the ability to easily simulate pillar behavior that is extracted from detailed pillar models, such as FLAC3D. MulsimNL/Large or similar approaches should be considered for evaluating mining layouts where stratigraphic conditions are known to cause overpanel weight to transfer to an extent significantly longer than the empirical method widely used to calculate load transfer distances in the U.S. [Peng and Chiang 1984; Mark 1987; USBM 1990]."

Jan 1, 2015

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999

By D. S. Kimbal

The McCoy/Cove mine is located 48 km (30 miles) south of Battle Mountain, Nevada, USA, in the Fish Creek Mountains at an elevation of 1548 m (5080 ft), see Figure 1. Joseph H. McCoy first discovered gold at this location in 1914. This discovery led to the Gold Dome Mine which produced the first gold from this area in 1928. After the Gold Dome era, the land remained relatively dormant until Houston oil and Minerals Corporation purchased the claims from the Summa corporation and defined an ore body at the present day McCoy pit. In 1986 Tenneco Minerals (formerly Houston oil and Minerals corporation), sold the McCoy mine and adjoining claims to Echo Bay Minerals corporation. The Cove ore body was discovered soon after the sale to Echo Bay. Echo Bay expanded the heap leach operation and built the present mill which began processing ore in the fall of 1989.

Jan 1, 1993

By T. W. Martin

The use of conveyors in large, open pit mines and their drawbacks are discussed. Technological developments such as long distance conveyors capable of handling large rocks are explored. The development and testing by the Bureau of Mines of a prototype crib and cable conveyor for handling large rocks are discussed, and possible modifications of the concept for a production model are examined.

Jan 1, 1984

By Sadatoshi Ohmori, Simin Zhai, Devini Abeyawardena

A road tunnel is planned to be constructed in soft, high overburden ground of around 600 m in Japan by using the center drift advancing method. The dodging effect and early ring closure of the center drift were expected to reduce the displacement and deformation of tunnel and promote safe construction. The measurement result during construction was analyzed and those effects, which the displacement and deformation after the widening excavation decreased and its effect increased as the center drift radius increased, were confirmed by numerical analysis. Also, the effect of the early closure of center drift after widening excavation did not have much effect.

Jun 23, 2024

By N. K. Dumakor-Dupey, G. B. Sakyi-Addo, K. J. Bansah

"Artisanal and small-scale mining (ASM) occurs in many countries around the world, and provides a source of livelihood to many impoverished local people in areas where it occurs. This paper reports the role of female participants and reasons why they engage in ASM. Field visits were made to 12 ASM sites located in the Tarkwa Mining District of Ghana to conduct interviews with male diggers and female participants. It was observed that over 100 women between the ages of 18 and 50 participate in ASM for survival. They engage in ASM largely because they have no alternative employable skills and income sources. These female participants depend on ASM to sustain the lives of their dependents. INTRODUCTION Artisanal and small-scale mining (ASM) conventionally involves use of rudimentary tools (such as picks, shovels, chisels and hammers) to exploit precious minerals and metals from the ground. It has been a major source of livelihood to many impoverished local people for more than a century. In many instances, it is the only source of income to indigenous people who have no alternative employable skills. The World Bank estimated that more than 100 million people around the world benefit from ASM which largely occurs in developing countries in Asia, Africa, Oceania, and South and Central America (World Bank, 2013). Cobalt, which is used in lithium-ion batteries to power cellphones, laptop computers, and electric vehicles, is largely produced by artisanal miners in Congo (The Washington Post, 2016). In Sudan, ASM is a significant contributor to the national economy, accounting for about 85% of total gold extracted yearly from 2010 to 2015 (Ibrahim, 2015). Also, according to the Embassy of Sierra Leone in Washington DC, USA, 90% of mineral export in Sierra Leone can be attributed to thriving artisanal diamond mining in the country (Sierra Leone Embassy, 2016). In Ghana, the ASM sector was recognized by government as a multimillion industrial activity, and through a series of initiatives, it was legalized by promulgating the Small Scale Gold Mining Law of 1989 (PNDCL 218). Presently, artisanal mining is widely practiced in two forms: licensed (registered), sometimes referred to as formal ASM, and unregistered (informal or illegal) operations, popularly called “galamsey”, a name believed to have been derived from “gather and sell” by ancient miners who could not communicate in the English language with European/British miners. The ASM sector in Ghana, like other countries, has seen a rise in female participation over the years. A report by the International Labour Organization (ILO) indicated that women account for about 15% of total workforce in ASM in Ghana, and up to 50% in Africa (ILO, 1999). Other researchers have also estimated women participants in ASM to be between 30 and 70% in Africa (Hinton et al., 2003a; Hinton et al. 2003b; Hilson, 2002). Presently, there is no reliable data from Ghanaian authorities on number of females engaged in ASM. However, data obtained from 15 ASM sites suggest that at least 40% of the employees are women. It is expected that a similar trend exists across ASM operations in Ghana."

Jan 1, 2017