Search Documents

By Reynold Q. Shotts

One often sees in the papers, in these days of ecological consciousness, estimates of the quantity of land that has been "devasted," "ruined," or "destroyed," by surface or strip mining, especially for coal. One feels sure that coal miners must have been the first to discover the art of excavation and that the public didn't know of its existance until five or 10 years ago! Estimates of the acreage vary widely with most of them sounding somewhat unreal. One estimate of 175,000 acres in Alabama appeared in one newspaper article and the implication was that all of this was mining for coal. The question was raised anew last summer when the author began working on a land use estimate utilizing aerial photographs, a preliminary project to the Alabama Earth Resources Technology Satellite (ERTS) contract presently being fulfilled. One land use category was barren or waste land and aside from some sand beaches in the two coastal counties in Alabama, recently strip mined land constituted most of that category. It quickly became apparent that old stripping was very hard to detect so that estimates from aerial photographs are not accurate. With regard to relatively new stripping, a thin veneer of reflective dirt washed over the countryside may result in a considerable overestimate of the excavated area. Actually, there is a way to estimate the area excavated by strip mining using published Bureau of Mines figures. At least three sets of data are needed: (1) Coal production figures, (2) average thickness of coalbeds mined, and (3) an accurate recovery figure.

Jan 1, 1973

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Duluth & Iron Range Railroad. The Duluth & Iron Range Railroad was built from Two Harbors to the Vermilion range at Tower, a distance of 67.6 miles, in 1884, and extended to Ely, twenty-one miles east of Tower, in 1888. It was built into Duluth in 1886, and branches were extended from its main line to the Mesabi mines in 1892 and 1893. The original grades on this road are very steep, going north, and in the thirteen miles from Two Harbors to Highland there is a rise of 1,150 feet. A new line between these points has been built with an increase of three miles in distance and with maximum grades of 1 per cent. Duluth, Missabe & Northern Railway. The Duluth, Mis¬sabe & Northern Railway was constructed from Stony Brook to Mountain Iron, a distance of 48.62 miles, in 1892. The Biwabik branch from Iron Junction to Biwabik, a distance of 15.54 miles, was constructed in 1892. The Superior branch from Wolf to Hibbing, a distance of 16.06 miles, was co11structed in 1893. The Alborn branch from Coleraine Junction to Coleraine, a distance of 53 miles, was constructed in 1906. The total main line mileage is 242 miles, of which 82 miles from Duluth to Hibbing is double tracked"

Jan 1, 1920

By Joe B. Rosenbaum

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Methods devised for achieving this stabilization include physical, chemical vegetative, and combination procedures. Although vegetative reclamation is preferred to physical and chemical stabilization, it is difficult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Nevertheless, recent research has developed methods for producing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $100 to $650 per acre. This report summarizes effective procedures developed for vegetating average tailings, the cost differential between the various methods, and suggests procedures that may be applicable for achieving stabilization of pyrite-containing wastes that may oxidize and become excessively acidic. The use of buried layers of sewage sludge to prevent this acidification is discussed.

Jan 1, 1972

By P. J. Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By Harrison R. Cooper

Approximately 40 concentrators throughout the world have successfully adopted computer control for flotation circuit operation since 1969. Successful use of flotation control, gaining up to 2% efficiencies, has largely derived from effective employment of on-stream slurry analyzers and integration of key measurement data through digital processors. Requirements for reliable measurement have also led to improved functional reliability in magnetic flow meters, pH, reagent feed, and other key elements. Methods used in computer control of flotation will be reviewed and variations in operating philosophies will be described with reference to the approaches taken to flotation automation.

Jan 1, 1979

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By Frank J. Klima

Explosives are probably the most widely used and most mysterious large scale' mining tools of modern times. The post black powder explosives were primarily nitroglycerin-based straight dynamites, ammonia dynamites, blasting gelatin, gelatin dynamites, ammonia gelatin dynamites, etc. Of these, the strongest and highest velocity explosive used in industrial operations is blasting gelatin, which is nitroglycerin colloided with a nitrocellulose of medium nitrogen content in proportions which give the product a plastic character, or about 93 to 7. Many variations of the basic groups above were developed by substituting ammonium nitrate and/or sodium nitrate for some of the nitroglycerin. The nitrates being insensitive to caps required a certain percentage of nitroglycerin to sustain detonation in smaller quantities or diameters. Paralleling the development of industrial dynamites was the development of more expensive, highly sophisticated explosives which were developed for specific military purposes. Such explosives as Amatol, RDX, Composition A, Composition B, Composition C, Lead Azide, PETN (Pentaerythritol Tetranitrate), Tetryl, Pentolite, TNT, etc., were primarily military explosives. Amatol, which is a cast mixture of ammonium nitrate and TNT (Trinitrotoluene), and identified by percentage of AN versus TNT as 50-50 Amatol, 80-20 Amatol, etc., was a favorite World War I explosive. RDX, or Cyclonite, was widely used in World War II. Also used during WW II were compositions A. B, and C, which were mixtures of RDX (Cyclotrimethylene trinitramine), TNT, and other nitrotoluenes. These high explosives, along with nitroglycerine, are exact chemical compositions or mixtures of exact chemical compositions which are individually explosive, or in other words, individually capable of explosive chemical decomposition when properly initiated. These chemical decompositions result in the formation of simpler compounds and/or large quantities of common combustion gases, and large amounts of energy in the form of heat. Of these, the most powerful is RDX which, based on the ballistic mortor test, is 1.5 times as powerful as TNT. Chemically, the decomposition of TNT releases about as much energy as the reaction of ammonium nitrate and fuel oil.

Jan 1, 1967

By Mehmet Bugdayci, Onuralp Yücel, Yeliz Demiray Cucurachi, Ahmet Turan

The production of strontium (Sr) metal from its oxide via an aluminothermic process under 1–5 mbar pressure was examined in this study. SrO of 99%purity by weight was used in the experiments. The effects of stoichiometry and the duration of the process on the efficiency ratio of the metallic strontium were examined. The effects of functional additives (BaO, CaO, CaC2) were also examined. Characterization was carried out using X-ray diffraction spectrometry (XRD), atomic absorption spectrometry (AAS) and flame photometry techniques. The highest Sr efficiency ratio obtained was 96.89% in the experiment conducted at 1250 °C with 300% Al stoichiometry and 300% BaO stoichiometry.

Aug 7, 2020

By M. H. Rauschkolb, J. A. Cremeens

Geotechnical solutions were developed for closure of two historic, remote underground mines in the deserts of southern California. Closure criteria included access closure, minimal site impact, and optimum use of native materials. The closure designs and construction activities incorporated techniques for protecting sensitive biota, particularly bats and desert tortoise. The types of mine openings that were closed include adits, declines, shafts, daylighted stopes, and dugout dwellings. The desert locations permitted implementation of cost-effective closure techniques that relied upon the use of native materials. The strategies and techniques developed for these desert closures are adaptable to other climates.

Jan 1, 2002

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By E. C. Wilson

The knowledge concerning the lubrication of open gearing for mining machinery has contained many unknowns and at its best has relied to a great degree on a "Rule of Thumb" procedure. It will be within the scope of this paper to explain what we have learned to date and what must be learned in the future. The results in the lubrication of open gearing have spanned the spectrum of unsatisfactory to satisfactory. With the advent of larger mining machinery, we are faced with the necessity of a more thorough knowledge of open gear lubrication. We have avail- able, better steels for the gearing, advanced technology and machinery for cutting proper tooth profiles, and better means of aligning the teeth in the gear train. This has made it possible to transmit more horsepower through the same size gear set than ever before, if we have the proper lubrication to complement the factors previously mentioned. We have set up computer programs which can calculate the data fox the tooth forms, the correct operating center distances, the contact stresses, the bending stresses, and the PVT factor of the gear teeth. This program does not, at the present, have sufficient data available to calculate the type of lubricant which should be used.

Jan 1, 1968

By F. E. Senftle

Preliminary geophysical surveys for nickel deposits are usually carried out by airborne magnetometer and surface electrical methods. Once an anomaly is discovered by these techniques, one must resort to chemistry to identify nickel and determine its concentration. Consequently, a method to determine nickel quickly and quantitatively at the exploration site could help guide detailed sampling and provide analytical data that might otherwise be delayed at distant laboratories. In addition, borehole probes capable of indicating nickel in the rock adjacent to the hole, should prove attractive to the exploration geologist. With these needs in mind, preliminary investigations have been made to demonstrate an in situ analytical technique which appears feasible for nickel exploration. The method depends on the very high energy gamma rays emitted when nickel absorbs a thermal or low energy neutron. These neutron capture gamma rays should be distinguished from the lower energy gamma rays emitted during decay of radioactive nuclides as in conventional activation analysis.

Jan 1, 1971

By R. S. Datta

Regulations on sulfur emissions have caused the electric utilities to evaluate various methods of meeting them. Low-sulfur, low-volatile coals can be burned alone or blended with high-volatile? coals. This option may be a cost-effective alternative to the installation of scrubbers on coal-fired combustion systems. In some blending applications, problems may be encountered because the low sulfur content and high calorific value of the low-volatile or other clean coal allow it to economically upgrade extremely poor quality coal. While this is done to meet specification purposes, actual boiler performance may be dominated by the poorer quality coal. Thus, the reputation of the low-volatile or other clean coal suffers. As a result of laboratory and full scale testing, conducted over the last five years, a model has been developed to evaluate the relative combustion characteristics of various coals and coal blends. A database for different coals has been gathered. This paper presents the model and shows how power plants and coal mine personnel can use it to evaluate their coals from different sources. It can be used to blend two or more coals from different sources so that thee blended coal has flame stability characteristics which are similar to those of the baseline coal.

Jan 1, 1991

By S. K. Pan, R. Venugopal, L. A. Kumaraswamidhas, Rakesh Prasad, Chandan Pandey

Cold compressive strength (CCS) and apparent porosity (AP) of pellets are essential properties regarding the burden of blast furnaces. The optimal required values for industries are 2.5 KN CCS and 21% AP. Blaine fineness and firing temperature are the decisive parameters analyzed here. During firing, microstructure phases such as silicate, hematite, and pore are formed. The phase’s grain density during induration influences the pellet’s CCS and AP. The influence of the factors over the response is evaluated by I-optimal (response surface methodology) design. Blaine fineness, firing temperature, pore phase grain density (PPGD), silicate phase grain density (SPGD), and hematite phase grain density (HPGD) affect the CCS and AP of pellets. The RSM-I-optimal predicted responses with a coefficient of determination (R2) of 0.89 for CCS and 0.91 for AP of iron ore pellets. Optimal conditions were Blaine no. = 1668 cm2/g, 1250 °C firing temperature, PPGD value 90 no/mm2, SPGD value 250 no/ mm2, and HPGD value 490 no/mm2, with 4.5 KN CCS 27%. The induration processes were investigated through statistical design of experiments for process optimization. Statistical analysis indicated the direct and interactive influence over CCS and AP. In this study, RSM-I-optimal modeling is used for iron ore pellets processing. The I-optimal prediction could be applied to make the process economical because information is obtained through fewer experiments.

Aug 18, 2020

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side of the continuous miner; 100 percent of the discharge redirected back toward the face, but divided equally to both sides of the machine; and 15 percent of the discharge redirected toward the face on the off-curtain side of the machine, with 85 percent directed into the return. These models were compared against a model with a conventional scrubber discharge, where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100 percent redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner, which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.

Jan 1, 2015

By Alexander Karim

This paper reviews the growth pattern in bauxite and alumina production, and primary aluminum smelting through 1980. Because the alumina and primary metal are intermediate products of the major integrated aluminum companies, it is not possible to determine their production costs. The costs indicated in this paper are order of magnitude costs based on published figures and the market price of these products. The conclusions in this paper indicate the general pattern of growth in the aluminum industry and are not meant to be a substitute for the feasibility and economic studies that are needed for individual bauxite mining, alumina refining and aluminum smelting projects.

Jan 1, 1968

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels ? from mining and processing to the manufacturing of Anished products. In 2009, the estimated real GDP of the United States decreased by 2.4 percent compared with, and the estimated nominal GDP was about $14.2 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. In 2009, the continued decline of the housing market was reflected in reductions in the production and consumption of cement, clays, construction sand and gravel, and crushed stone (those mineral commodities that are used almost exclusively in construction). Production of mineral commodities associated with the manufacture of goods for the housing market, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard also decreased. Declines in auto-mobile manufacturing resulted in reduced production

May 1, 2010

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicated the potential for scrap formation, validated through lab experiments with varying coke rate, basicity, and holding time. The investigation discovered that smelting this combination could yield a metal product comprising 59% Fe, 24.93% Cr, 7.56% Mn, 0.62% Ni, and 0.93% Si. The optimum basicity was found to be 0.6 with 80% recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall CO2 emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of USD 330 per ton.

Jan 10, 2024

By Paul R. Weber

Open-pit mines are constructed in materials characterized by the complete range of geologic materials from the most recent alluvial sediments to hard intact crystalline rock. The determination of stable slopes in recent alluvium is in the realm of soil mechanics, an established engineering discipline, well founded on theoretical development and years of substantiating experience. The analytical tools of the soils engineer are chiefly derived from continuum mechanics wherein load-deformation response is governed by mass properties of the substance. At the other end of the spectrum, slopes in hard unweathered rock can generally be analyzed in a straightforward manner by the methods of discontinuum mechanics wherein the properties and orientations of joints control the response of the material. This approach is exemplified by the classical work of Terzaghi (1962). In between these two extremes is a gray area of material types which are composed of stiff soil and incompetent rock. This area is of importance to the mining engineer, since a large portion of open-pit mines is excavated wholly or in part into incompetent rock. This paper describes an approach to pit slope design in incompetent rock in which the material behaves essentially as a continuum. A wide range of geologic materials from stiff soil to poorly indurated sandstone and shale to crushed or weathered crystalline rock appear to fit in this category. These materials all possess certain mechanical properties which must be accounted for in a realistic assessment of slope stability. These properties include nonlinearity, s tress -dependency, and inelasticity. Further considerations involve residual stresses and time-dependent seepage pressures where groundwa.ter is present.

Jan 1, 1971