Search Documents

By F. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower Partnership Mine to Twin Buttes. The system, supplied and installed by Cable Belt Limited, of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240 kw (3000 hp) drive and a 60° angle bend. Construction was completed in two years. Full production was attained after several months' operation.

Jan 1, 1979

By R. S. Shoemaker

Environmental and regulatory authorities are increasingly requiring that precious metals heap leach piles be contoured before they are abandoned so they may present a more "natural" look to the eye. Depending on the ore type, many of these contoured heaps will be subject to substantial erosion by precipitation events, native plants will have difficulty in establishing themselves and slimes be washed onto surrounding areas or into watercourses. This paper presents the argument that the results of contouring heaps are counter to good environmental practice. Calculations which have been made demonstrate that leveling and berming the heap tops as well as berming the edge of each lift or setback will effectively prevent water erosion and promote the growth of native plant species.

Jan 1, 1993

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

Calcite has found many applications in the industrialized countries recently, such as filler for paper, paint, plastics, rubber and food. Furthermore, calcite separates many toxic elements, and thus it is used in water treatment, and it is also used to raise the pH of drinking water. Due to its special features, calcite has been characterized as a useful coating and reinforcement filler for applications. Finer particle size of calcite has been determined to provide improved features for all of these applications. For submicron particle production, wet milling is selected over dry milling to produce finer particle sizes. Wet stirred media mills are also used in many industries. For that reason, this study investigated the effects of operating parameters on particle size reduction in the wet grinding process. The knowledge acquired by this study will allow the finding of optimal operating parameters for a stirred media mill to optimize specific energy consumption and reduce particle size.

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By Norman K. Olson

A geologic investigation of mineral resources in South Carolina first began in 1825 when the General Assembly authorized Lardner Vanuxen to conduct a "Geological and Mineralogical Survey of South Carolina." Vanuxen, South Carolina's first State Geologist, reported in 1826 on the limestones (marble) of the Piedmont which during those early years, were burned in many shall, scattered kilns in the region wherever suitable raw material was available. He also mentioned the possibility of using marl from the Atlantic Coastal Plain province for direct application and enrichment to the soil. Since before the year 1844 industrial minerals in South Carolina have been commercially produced literally from A to Z, asbestos to zircon. The first pub¬lished reports of actual commercial production, not just an occurrence, are referenced in Table 1 for 33 known industrial minerals and rocks in South Carolina. Known or suspected occurrences of undeveloped non-metallic mineral resources in South Carolina await future verification by geologic mapping, sampling (including coring), possible beneficiation, and market analysis. These industrial minerals and rocks include, but are not limited to, special, clay minerals (e.g. bentonitic clays, zeolites and others), sillimanite, argillite (lightweight aggregate), kaolin (alumina) and marl (underground storage and tunneling medium). In addition other non-metallic minerals, once mined but still worthy of reconsideration, include topaz (industrial), heavy minerals, barite, feldspar, and monazite. Finally, possibilities for new reserves, as an expansion of existing mine output, might develop for fuller's earth, limestone (lime), sericite (finely divided mica), vermiculite, kaolin (paper coating and filling, other filler), and metallurgical gravel. Official South Carolina data from the U. S. Bureau of Mines for 1974 indicated a total value of mineral production of $105.2 million. During 1974 production consisted of cam-on clays, (brick and tile), fuller's earth, kaolin and vermiculite

Jan 1, 1977

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By Fred C. Bond

Any improvement in the accuracy of commercial comminution calculations under the Third Theory must be accomplished either by increased precision in energy input measurements, or by a better evaluation of the total new crack length produced, as indicated by the feed and product size distributions. Since at the present time feed and product sizes are approximated solely by the microns 80% passes, the most promising opportunity for increased accuracy lies in consideration of their plotted size distribution characteristics. This paper shows how more accuracy can be obtained over an increased range of feed and product sizes from size distribution studies.

Jan 1, 1962

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By Shenghui Chu, Zhibiao Guo, Dongshan Yang, Yuanxin Zhao, Xiaohui Kuai, Jingwei Gao

The technology of automatically formed roadway without pillars (AFRP) via roof cutting and pressure releasing (RCPR) is a reformatory method for gob-side entry retaining, which automatically creates a roadway by utilizing the fragmenting and expanding properties of rock strata and the mining pressure, to realize a novel technique for coal mining without coal pillars. The Anju Coal Mine is the first kilometer-deep mine where this technology is applied. To conduct a geomechanical model experiment, this research uses the 5307 working face in this mine as its backdrop. The experimental results show that this technology can efficiently decrease the pressure of the AFRP surrounding rock. The roof maximum stress of the AFRP is 21% lower than that of the belt roadway, while the side abutment pressure of the former is 13.4% lower than that of the latter. The comparison of model experiment data and field monitoring data shows that the roof and floor approaching deformations on the roof-cutting side and solid coal side of AFRP differ by 8.8% and 9.6%, respectively. The model experiment results and field monitoring data show good agreement, and the deformation of the AFRP surrounding rock can be successfully managed by this technique. The study’s findings can serve as a guide for using this technology in kilometer-deep coal mines.

Jul 31, 2023

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

By H. Murray

Introduction Industrial minerals are key ingredients in a large majority of domestic and industrial products that are used in our daily lives. In the 7th edition of Industrial Minerals and Rocks, fifty three industrial mineral commodities are described. A precise definition of industrial minerals and rocks is difficult. Bates (1975) proposed a definition which is widely used and is as follows: "any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the non-metallics". They can be igneous, metamorphic, or sedimentary and range in price from a few dollars per ton to a very high price of hundreds of dollars per ton. The growth in their production and use is closely allied with population growth particularly in countries that maintain a high standard of living. The United States just passed 300 million in population and it is predicted that by 2040 the population will be 400 million. This will result in large increases in the need for Industrial minerals. Other factors that relate to increased use of industrial minerals are increased research and development by the producing companies and better quality control. Many industrial minerals such as kaolin, barite, nepheline syenite, fluorspar, lithium carbonate, phosphate rock, potash, talc, and several others are exported from the producing countries to many users around the world which has significantly increased their use. Also, government agencies, State Geological Surveys, and Universities have contributed to their growth by their research and development activities.

Jan 1, 2007

By Joel Lööw, Jan Johansson, Erik Lund

Digitalization and automation technology offer new possibilities to increase productivity and obtain higher levels of autonomy in mining operations. Introducing autonomous systems into mining is not only a technical problem in terms of effectiveness and efficiency, nor a problem of safety in human-automation interactions. The systems also need to be designed and developed so that they foster healthy and attractiveworking environments. The design and development phase of newmining technology has not been extensively studied previously. To fill this knowledge gap, we investigated technology developers’ basic assumptions about humans and their interactions with the technology they develop. We conducted five semi-structured workshops within an EU funded project concerned with developing digitalization and automation solutions for the mining industry. The data suggests that many critical functions will still be under human control in future mining systems. The results also indicate increased complexity in the interaction between autonomous systems and humans as the technology becomes more advanced. As a result, we suggest that a human perspective, based on sociotechnical principles, should not only be considered in implementing the technology at mines but also in the early conceptual phases of developing and designing the technology. This will ensure healthy and attractive work environments in the future mining industry.

Mar 26, 2024

By Herschel H. Potter

Back injuries arising from such activities as lifting and handling objects have been and continue to be constant and undiminishing hazards of the occupational environment. Back pain in one form or another is experienced by almost a1 1 individuals. During the past 30 years, a great deal of accident prevention education has been directed toward the reduction of back injuries. However, it has not produced any great change in the incidence of the injury. The human spine remains the most vulnerable area of the muscul o-skeleta1 system. Back injuries account for about 400,000, or 18 percent, of all disabling work related injuries each year according to the National Safety Council estimates. These serious back injuries are estimated to have cost more than 1.9 billion dollars in 1976 in medical and lost time pay. 1

Jan 1, 1981

By Theophilus Mensah, Kwame Awuah-Offei

Engineers face significant challenges when determining what geometry provides the most profitable and safe stope for extraction. Several techniques and optimization algorithms have been developed in recent years, but most fail to find optimal solutions because they are heuristic or LP-based without efficient geometric constraints. This paper presents a two-dimensional binary linear programming (BLP) model for determining the optimal combination of blocks in a stope that maximizes the economic value of the layout of stopes for a sublevel deposit. The work draws from Queyranne and Wolsey’s (2017 & 2018) formulations of tight constraints for bounded up/down times in production planning problems to formulate novel and efficient geometric constraints along with geotechnical and grade constraints for the BLP stope layout optimization problem. Results from the model indicate that it is possible to formulate efficient shape constraints in LP-based approaches. The model used for the numerical example contained 144 valuable blocks out of 774 blocks, which translates into an economic value of $53.21M. The BLP model selected 60 valuable blocks and 13 waste blocks that met all constraints translating into a maximum economic value of $34.4M in 1.83 hours within a gap tolerance of 0.00%.

Jun 25, 2023

By S. Deming

Coal is China's main source of energy. In 1988, 76.1% of commercial energy consumption was supplied by coal. To provide a rational utilization of its coal resources, China has paid considerable attention to coal preparation over the last 10 years. In 1980, there were only 105 washeries treating about 100 million tonnes of coal, but by 1988 there were 151 washeries treating 171 million tonnes per year. This paper describes the development of China's coal preparation industry; its growth, the equipment, and the technology. Statistics and information on the current status of the industry are also be presented.

Jan 1, 1991

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

By Serdar Aktaş, Özgün Küçükoğlu, Burcu Nilgün Çetiner, Mehmet Hakan Morcalı

This study compares the cementation performance of metallic iron, metallic aluminum, and metallic tin in terms of the reaction conditions and parameters in synthetic antimony chloride solutions. The effects on the antimony recovery (%) caused by the cementators’ types, stirring speed, reaction time, and temperatures were explored thoroughly. The cementation kinetics of antimony were also explored for each cementator. The activation energies were determined to be 10.99, 9.09, and 13.58 kJ mol– 1 for Al, Fe, and Sn, respectively. The results reveal that the reaction is diffusion controlled, and comparable results were obtained for each cementator. At 25 °C, 40 mg of iron powder was found to reduce all antimony ions (i.e., approx. 99% recovery), but even when 100 mg of Al and Sn cementators were used, the antimony recovery did not reach 100%. This result shows that iron is the best candidate to cement antimony out of the solution.

Jan 28, 2022