Search Documents

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

Accurately estimating load distributions and ground responses around underground openings plays a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the mining-induced loads, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses, both empirical and numerical. In this study, the numerical modeling approach recently developed at West Virginia University, which is based on the modeling approach developed by the National Institute for Occupational Safety and Health (NIOSH), is investigated using the finite difference software FLAC3D. The model includes the longwall panels, the adjacent chain pillar systems, and the different stratigraphic layers of the overburden. Using the 3D model, changes in loading conditions and deformations on the areas of interest, induced by an approaching longwall face, can be examined. This paper details the 3D modeling of a longwall panel utilizing this approach, and the verification of the results against field observations. The studied panel was 360 m wide with a 3-entry chain pillar system and about a 160-m average overburden depth around the studied area. The overburden strata consist of alternating layers of shale, sandstone, and limestone. The FLAC3D results were compared against field measurements from the mine site. The stress change values measured in the chain pillars were comparable with the modeling results. The model also replicated the surface subsidence profile obtained from field measurements fairly well. Overall, the 3D modeling approach was found to be successful for the case study longwall panel.

Sep 23, 2020

By D. V. Bush

There has been a great deal of evaluation and discussion on the economics of semi- autogenous grinding versus conventional grinding circuits. This paper will not discuss the merits of one system over the other, but rather will discuss the Henderson Mill&apos;s approach toward achieving the most economical milling conditions in its existing SAG mills.

Jan 1, 1985

By Shenghua Yin, Xun Chen, Rongfu Yan, Zepeng Yan, Wei Chen

The application of cemented paste backfill (CPB) with alkali-activated slag and phosphogypsum (ASP) can contribute to the sustainable development of the mining industry. The effects of PG content, NaOH content, solid content, and waste rock-rod milling sand (W/R) ratio on workability, unconfined compressive strength (UCS), and setting time of ASP-CPB were investigated in this paper. The results showed that the workability of ASP-CPB decreased with PG content and NaOH content. Compared to OPC-CPB, ASP-CPB exhibited better workability and higher long-term (7 days and 28 days) strength at predetermined backfill formulations and curing times. The mid-term strength of ASP-CPB first increased and then decreased with PG content, while the short-term strength (3 days) decreased gradually due to the influence of soluble acidic impurities. Excessive NaOH will harm the strength of ASP-CPB, possibly due to the swelling effect of the reaction products (ettringite and sulfate). Strength and setting time increased and decreased with solid contents, respectively. Moreover, the compactness of the mixture has an important effect on strength and workability. The workability and strength of ASP-CPB reached the minimum and maximum values at a W/R ratio of 5:5, respectively. Pollutant index detection indicated that most of the pollutants in ASP-CPB leachate met the discharge standard, which proved that ASP-CPB is an effective method to recover PG. The results of the research will provide theoretical guidance for the efficient recovery of PG resources and support the achievement of safe, clean, and efficient mining.

Nov 17, 2023

By Pedro Sanchez-Mejorada

Laguna del Rey is the name of a dry lake bed located in the State of Coahuila, Mexico in a semi-desertic terrain typical of the basin and range physiography. Química del Rey, S.A., a subsidiary of Industrias Peñoles, has been producing sodium sulphate since 20 years ago, from brines pumped from the sub-surface of the present playa. The spent brine is used as raw material for the production of magnesium oxide. An extensive, lenticular deposit is found just below the playa. It consists mostly of glauberite (sodium-calcium sulphate) and blöedite (sodium-magnesium sulphate). The glauberite occurs as thin crystals oriented at random and leave many void spaces among them. These intercrystalline spaces are partly filled with mud, but the whole mass of the evaporite is still very porous. A brine that contains in solution ions of sodium, magnesium, sulphate and chlorine occupies the voids of the sponge-like evaporite body.

Jan 1, 1984

By Adrian C. Dorenfeld

[Agitation and transport of slurries have been investigated intensively for the past twenty years. It has been shown (1) that slurries have the properties summarized in Figs. 1, 2, 3, 4, and S. For a detailed exposition the reader is referred to the above reference and the bibliography, which, in turn, have extensive references and bibliographies. An interesting problem with which the senior author has been concerned with is the scab up of power requirements for slurry agitators operating in the laminar region with pseudo plastic materials. Pulps of shaly ores, after various chemical reactions in aqueous leaching systems, are often difficult to settle and filter if agitation is violent. In these cases agitation must be at a minimum, yet prevent [tling] such as in copper uranium ores. This mild agitation is on the laminar region.]

Jan 1, 1967

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By T. W. White

One of the objectives of today&apos;s mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

By Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducrng bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the porosities of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900&apos;s to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also extended a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore modes. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of the first of June 1984, a total of 29.4 million long tons of sulphur had been produced west of the Pecos -aver. Duval produced more than 88 percent of that total.

Jan 1, 1984

By RIINA SALMIMIES, Paula Vehmaanperä, Antti Häkkinen

The dissolution of iron oxides in mixtures of acids is fairly uncommon but can result in a more efficient dissolution process. The objective in this work was to investigate the dissolution of synthetic hematite powder in mixtures of oxalic and sulfuric acid. Experiments were done at different acid ratios and temperatures. An increase in temperature from 15 to 35 °C increased solubility, whereas an increase from 35 to 50 °C did not change the solubility but had a profound effect on the kinetics. An important finding was that oxalic acid advanced the dissolution process since increasing the amount of oxalic acid in the system resulted in faster kinetics and higher solubilities. The dissolution kinetics were well described with the Kabai model, which was the only studied model able to describe the whole reaction time. However, the solid specific constant a varied for the different acid ratios and this is argued to be a result of changes in the solid phase. The changes in the constant a were not in line with the original study of Kabai, which indicates that a cannot be the solid specific constant but it can be the constant connected to dissolving media describing the changes in the dissolution mechanism.

Sep 23, 2020

By Michael Moats, Weston Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the USA. Electric arc furnace dusts processed to recover zinc produce a process residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine the predominant mineral phases and leached with common mineral acids. Atmospheric agitated leaching using sulfuric acid and hydrochloric acid were examined to determine the extractions of gallium, indium, and germanium as a function of concentration, temperature, and time. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 82%, ~100%, and 89%, respectively.

Aug 8, 2023

By Oliver W. Marsden, John O. Marsden

This paper presents the results of a hypothetical case study that evaluates the potential transition of a large copper mining and extraction operation to 90% renewable energy. The case study considers three phases to accomplish such a transition; phase I considers installation of renewable power generation at the site to meet a portion of the current electric power needs, phase II considers conversion of diesel combustion mining equipment to electric equipment, and phase III considers implementation of renewable energy generation coupled with energy storage systems to provide approximately 90% of the total mine site energy requirements. The paper evaluates the results in the context of a range of purchased electric power unit costs ($0.065, $0.100, and $0.135/kWh) as well as various carbon tax scenarios ($0, $5.00, and $37.30/t CO2). While the case study is hypothetical and considers a range of assumptions, it clearly identifies a pathway to potentially economically viable transitions to a renewable energy platform for mining companies. This represents an approach that mining companies can use to help to meet emissions targets, as well as social responsibility and reporting requirements.

Jun 4, 2021

By Klaus Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300 and 600 °C is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies depending upon structural homogeneity, porosity and gangue quantity. Especially sinters with heterogeneous structures transmit stress to the hematite phase and this favours disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1981

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Cat 994 class) as primary loading equipment in open pit iron ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Data were gathered on loader selection rationale; operating and maintenance experience; and production, availability, and cost information. Brief time studies were conducted to indicate machine performance and utilization. The paper summarizes the field data and includes economic comparisons of wheel loaders versus cable shovels in an iron ore application.

Jan 1, 1996

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dozer operators are frequently exposed to whole-body vibration (WBV) during the execution of their work. Occupational exposure to WBV in Indian surface coal mines was evaluated by measuring vibration intensity and duration of exposure. A triaxial accelerometer was placed on the operator seat surface for taking the readings. Based on frequency-weighted root mean square acceleration equivalent to 8-hr shift duration, i.e., (A(8)) all dozer operators have exceeded an Exposure Action Value (EAV) of 0.5 m/s2 , and 90% of dozers did not exceed Exposure Limit Value (ELV) of 1.15 m/s2 . Based on Vibration Dose Value (VDV (8)), all dozer operators have exceeded Exposure Limit Value (EAV) of 9.1 m/s1.75, but no dozer operators have exceeded Exposure Limit Value (ELV) of 21 m/s1.75. Further, an epidemiological study was performed for identifying the extent of musculoskeletal disorders (MSDs) among dozer operators. For the detailed study, 42 dozer operators and 22 controls were selected from 2 surface coal mines. The control group was not exposed to WBV. It was seen from the cross-sectional study that pain in the lower back was predominantly higher (83.33%) in the exposed group when compared with the control group (31.81%). Likewise, pain in the neck (47.61%), shoulder (42.85%), knees (42.85%), and ankle (11.90%) was higher in the exposed group than that of the control group (22.71%, 0%, 45.45%, and 4.54%). A significant observation among the exposed group was that there was degradation in the quality of life. The outcome of the study would assist in monitoring and mitigation of machinery-induced vibration diseases (MIVD) in India and generally applicable to most of the mechanized mines as well. However, comprehensive studies are still needed to enunciate the magnitude extent.

By A. J. Basu

An overview of the evolution of computerized mine planning and design has been given, emphasizing the need for a knowledge-based system for planning and design of underground coal mines. An outline for the development methodology and procedure has been provided. Problem structuring guidelines have been used to incorporate intelligence and integration to the design modules. A skeletal model for a mine planning and design expert system has been prescribed, and the development process has been documented in detail. A feasibility prototype has been developed to test the structure of the skeletal model and to ensure completeness of the design process. The feasibility prototype development and its contribution toward proto typing has been addressed in this paper. At present, prototype development is underway. The prototype is expected to be avail-able for testing and implementation in early 1991.

Jan 1, 1991

By Howard W. Adam

Mill length was the primary variable investigated in an autogenous pilot mill circuit. The 5-1/2&apos; diameter mill had both pebble ports and 1/2" wide slotted grates. The plus 1/2" mill product was crushed in a cone crusher and returned to the mill feed along with the minus 1/2" plus 4 or 6 mesh fraction. Tests were run with a short mill, inside length of 26-3/8", or diameter-to-length ratio of 2.50 to 1. The same mill was then lengthened to 48-3/8", diameter-to-length ratio of 1.36 to 1. The effect of mill length on circuit product characteristics was studied. Results show that (1) circuit throughput or grinding rate is lower per foot of mill length in the longer mill, (2) the long mill product is finer than the short mill product, and (3) KWH per ton of circuit product is slightly higher with the longer mill; however, KWH per ton of minus 200 mesh material (finer fraction) produced is essentially the same in the long mill as the short mill, It is not known whether the relationships found for the pilot mill are valid for commercial size mills.

Jan 1, 1973

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems. Included are discussions of a full-scale laboratory test bed that was designed to simulate a working conveyor system as well as the challenges and successes of integrating the IoT system with the test bed.

Oct 6, 2020

By B. Holen, J. R. Baregi, J. A. Organiscak, A. B. Cecala

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-µm respirable size particulates under various HVAC airflow operating conditions.

Jan 1, 2015

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021