Search Documents

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

By K. K. Kohli

Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence-induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include 17 longwall panels and 2 room and pillar sections. The data in-each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages.

Jan 1, 1980

By B. W. Stunkard

Hibbing Taconite Company is located by the cities of Hibbing and chisholm near the center of the Mesabi Range, approximately 169 km (105 miles) from the Canadian Border. The plant site is equidistant from these two communities, about 6.4 km (4 miles) from each. A 169 km (105 mile) railroad connects us with the port of Superior, Wisconsin, where the pellet production is loaded into lake carriers for lower lakes destinations. Immediately to the south of the mine area is the world famous Hull- Rust-Mahoning Mine which produced more than 700 000 000 million tons of red ore between the years 1893 and 1973.

Jan 1, 1979

By H. D. Dahl

In January, 1969, the Central Research Division of Continental Oil Company initiated a research program on roof control. The purpose of the research was to improve roof stability. Toward this end, it was necessary to determine which of the many geological and geometrical variables have a significant effect on roof stability. The isolation of these significant variables would allow research effort to be concentrated where it would be most effective in improving roof control. The research effort was directed toward two major objectives. One was to de-fine the geological and/or geometrical parameters that affect the severity of roof conditions in any particular area of the mine. This study was concerned with roof fall intensity. The second was to define why roof falls in Humphrey No. mine (and in northern West Virginia-south-western Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. This study was concerned with roof fall orientation. To provide a reference framework for further discussion, a geological description of the area is presented in Part II. In Parts III and IV, the procedures, methods, and 'results of the research applied toward the afore-mentioned major objectives are presented. Part V contains the conclusions and recommendations for-warded by this study.

Jan 1, 1971

By R. F. Pearce

The paper in based on laboratory and pilot plant investigations which led to the development of a series of processes for production of high purity metals from nickel-copper-cobalt mattes of a wide range of composition. The selection of ammonia pressure leaching or acid pressure leaching for various mattes is discussed. This is followed by discussion of various methods for leach solution purification and metal separation. The metals of high purity are produced by reduction with hydrogen from purified solutions. Examples are given of complete flowsheets for a number of mattes. Drawing upon those examples, general principles for the selection of the most suitable treatment process for particular material are outlined. Under certain circumstances, those processes may replace part of the pyrometallurgical treatment and all of the electrolytic refining steps which are customary in the treatment of nickel-copper-cobalt mattes.

Jan 1, 1959

By C. R. Tinsley

Investment activity in the Pacific Rim of Fire has seen a phenomenal surge from epithermal gold exploration. Individual countries are attractive because of lower up-front minerals lease costs (US, Canada), better geological prospectivity (Chile, Indonesia), or cheaper equities (Australia). Since the October 1987 stock-market crash, large companies are shedding minority joint venture interests to focus on core businesses. Some vertical integration is evident in Japanese coal investments in the Pacific Rim. This paper does not cover the aluminum industry oligopoly which is multi-national in character nor does it cover the many Canada to US minerals investments. It will be interesting to see if the new US-Canadian free-trade treaty will reverse that investment flow.

Jan 1, 1990

By Raymond K. Will

Computers are becoming increasingly valuable tools in the mining industry as a greater variety of appropriate hardware and software becomes available, combined with greater acceptance by management, Within a given time period an engineering staff can evaluate or design a project to much greater detail and higher accuracy by utilizing computers once suitable programs have been developed. We are all aware that throughout the world the decreasing grade of minerals coupled with increasing waste to ore ratios necessitate larger capacity, longer term mining operations and attendant higher capital costs. Computers can be of assistance in all stages of mineral exploitation, from geologic exploration through mine feasibility studies and design, to marketing and transportation. Because of the high speed with which data can be digested and manipulated by computers, preliminary information from any stage of investigation can be analyzed to assist in further guidance of that stage. By use of preliminary mine feasibility studies, financial forecasts and sensitivity analysis, even information from a far-removed phase such as marine transportation of the product, can help guide the exploration phase to a realistic target.

Jan 1, 1973

By William H. Dresher

A recent report to President Reagan from the Business-Higher Education Forum, entitled, "America's Competitive Challenge: Need for a National Response," (1) observes that in the recent past, ". . . much of that research, which is necessary for major breakthroughs and sustained productivity improvements, was redirected to short-term objectives ... At the same time, American universities, which conduct more than half of the nation's basic research, have suffered from an accumulated under-investment in facilities and equipment amounting to an estimated $1-4 billion." Also contributing to the decline in America's productivity, the report said, are "...weak technology transfers between government and industry and between universities and industry..." This report as well as other recent reports and articles have, reopened a subject which has long been debated but rarely resolved-- the interaction between the academic community and industry in the sponsorship and conduct of research. The subject is unfortunately, too often treated as a controversial issue involving ethics and the profit motive when, in fact, the two branches of society -- industry and academia -- are necessarily part of the same system. I would like to speak to you today on the subject of university-industry interactions and to some extent discuss the role of government in such interactions. Finally, I will make some remarks as to how this subject applies to the mining industry.

Jan 1, 1984

By Kunzo Amano

Fully-bonded rock bolts have been widely used in construction sites and mines in recent years. The purpose of this investigation is to prove the effectiveness of rock bolt supports in unstable ground through in-situ tests and numerical analysis. 2. MEASUREMENTS AND PROCEDURES OF IN-SITU TESTS The fully-bonded rock bolts as the mine road¬way supports were tested in the Fukasawa mine which is located in the northeast district of Japan (Fig. 1). The Fukasawa mine (one of the Kuroko mines) started the production in 1973, and the present monthly production is slightly less than 20,000 tons. The ore deposit which exsists at about 400 m depth is divided into several small lenticular shaped bodies. They are distributed apporiximately 1500 m in NW-SE direction and 700 m in NE-SW direction. The hanging wall is basaltic lava and the footwall is tuff. The rocks surrounding the ore bodies are soft but relatively intact, so the trackless mining system has been adopted from the beginning of the development.

Jan 1, 1982

By David R. Maneval

The mining of coal in Alaska receives special treatment in the Surface Mining and Reclamation Act passed by the U.S. Congress in 1977 (PL95-87). Section 708 of the Act required that the National Academy of Sciences (NAS) perform a study of "Surface Coal Mining Conditions in the State of Alaska, In Order to Determine Which, If Any, of the Provisions of the Act Should be Modified with respect to Surface Coal Mining Operations in Alaska'. The special committee on Alaskan Coal Mining and Reclamation of NAS completed their study in 1980 and prepared their report (NAS, 1980). At this time, the Secretary of the Interior and the Congress have taken no special action with regard to either special regulations geared specifically to Alaska or to submitting special draft legislation to the Congress requesting amendment of PL95-87. The Alaska Department of Natural Resources (DNR) has drafted legislation which was submitted to and passed by the 1982 session of the State Legislature. The State regulatory agency has also drafted the requisite regulations necessitated by the amendments to the State's Basic Coal Mining Act. It is expected that by mid 1983 DNR will have applied for "primacy" to the office of Surface Mining, U.S. Department of the Interior (OSM). They will be submitting the amended State Law, the revised State Regulations and an operational plan as called for by OSM regulations. The presumption is that primacy will be granted to the State of Alaska under PL95-87. The Usibelli Coal Mine continues to be the only operational commercial mine for coal in the State of Alaska. It produced 7.26 x 10 kg (8 x 10 " T) of coal during 1981. The current mine was started in 1920 by Captain Lathrop, an early developer and pioneer in Alaska. It was continued by Emil Usibelli and was taken over after the death of E. Usibelli (in the 1964 earthquake) by his son Joseph Usibelli who is the current President of, the firm3 Their latest improvement is a 27.5 m (36 yd. )Bucyrus-Erie Dragline which handles most of the overburden removal. The coal is removed by a loader-truck combination. They are currently starting up the use of a unit train loading facility which handles forty cars every two hours. This loading system was a development necessitated by the Sun Eel Export contract. The Alaskan Railroad was a major cooperator in the development of the first unit train loading facility in Alaska.

Jan 1, 1982

By Frank H. Madison

The percentage depletion deduction on Federal Income Tax Returns under the provisions of the 1939 Internal Revenue Code and of Sections 611 to Section 615, inclusive, of the revenue act of 1954, have created innumerable administrative difficulties, and a new interpretation of "gross income from the property" in that the Courts have expanded the ideas of what constitutes "gross income from the property" to a degree unheard of and unthought of prior to the enactment of these two codes. Originally, under the Revenue Acts of 1917, 1918, and 1920 depletion was allowable, based upon mine valuations as of March 1, 1913; if the mine was owned prior to March 1, 1913; upon cost, as of the date of acquisition if purchased subsequent to March 1, 1913; and upon a "discovery" basis if the mine was discovered after March 1, 1913, The "jab" for mine valuations as of March 1, 1913 and for discovery valuations and depletion was not as bad as it has been made out to be. Thousands of valuations and estimates of reserves were made and agreed upon between taxpayers and Internal Revenue Service engineers and as the years went on the answers have been found to be "reasonable." However, human nature being what it is each case was a battle of wits - of a sort - and many resulted in severe differences of opinion and litigation. As tax rates increased the situation was not bettered. I could talk for several hours on this phase of depletion but it is all past now andwould not give any real service or better understanding of the matter.

Jan 1, 1958

By S. Rukhaiyar, M. Ramulu, G. Pradeep, P. K. Singh, P. B. Choudhury

The drill and blast method is the most prominent rock excavation method used in mining and civil engineering projects. The ground vibration is the most undesirable effect of the blasting and needs to be controlled. The blasts are designed so that ground vibration at nearby structures must remain under the prescribed limit. Various empirical blast vibration attenuation models have been presented to estimate the ground vibration for designing purposes. These models assume ground vibration as a function of distance and maximum charge per delay. United States Bureau of Mines (USBM) model is most commonly used for the blast design. However, the uncertainty associated with these models is seldom characterized, thus diminishing its reliability. The probabilistic Bayesian approach associated with the Monte Carlo method can easily quantify uncertainties associated with the model and its parameters. Thirty-three blast vibration observation data from a granite quarry in Kerala, India, is used to estimate the probability distribution of model parameters. Markov Chain Monte Carlo (MCMC) approach is used for sampling 12,000 samples for obtaining the posterior distribution of parameters. The uncertainty associated with model parameters is quantified from the posterior distribution, and this is further used to estimate the credible and prediction limits of the model. The point estimate of the most optimum value of the parameter is estimated using maximum-aposteriori or MAP estimate. The model parameters are also obtained using the commonly used least-square error method, which is a maximum likelihood estimation or MLE approach. It has been observed that the accuracy of the model obtained using both MAP and MLE approach is almost equal. However, the MAP estimate as per Bayesian probabilistic analysis has the added advantage that it can estimate the uncertainty of parameters as well as the model, which is not possible using the MLE approach.

Sep 27, 2021

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986

By A. L. Holmes

This presentation in the open pit session deals with the development of a phosphate rock strip mine by CF Industries, Inc., a company that does not presently mine in the Central Florida Phosphate District. Land acquisition, engineering, financing and environmental permitting activities were begun in early 1975; site preparation, environmental monitoring and dragline construction began in mid-1975. The operation is due on-stream in late 1978. The reserve acquisition, permitting, and financing could each easily be developed into a separate paper of interest. Each, however, has been covered before for other mining ventures with similar capital and environment requirements. For that reason, I have chosen to discuss what CF Industries, Inc. is, why it is entering this new sec-tor of the agricultural chemicals business, and, to keep at least some technical basis, what design modifications are possible when the total mine output is used captively and it is unnecessary to have the flexibility to meet the numerous transportation and customer specification considerations. In an attempt to show the size and complexity of the CF organization, a brief description of existing facilities should help show why the big interest in mining phosphate rock.

Jan 1, 1977

By W. G. Lawrence

The rapid development of science and technology in Russia has been the result of well laid plans since 1918. At that time the Institute of Silicates was established is Moscow and later the establishment of similar more specialized institutes for the study of cement, glass, refractories, construction ceramics, electrical ceramics, building materials and asbestos provided the necessary research facilities for studies related to all types of ceramic inorganic materials. The' Institute of Ceramics and the Institute of Silicate Chemistry, Academy of Sciences, USSR, were founded in Leningrad. The work now going on in these various research' institutes covers every branch of silicate science and ceramics The impetus behind such establishment of special¬ized laboratories is no doubt due to the 5-year plans and the necessity of improving the scientific knowledge regarding the materials being used and the products being manufactured.

Jan 1, 1960

By Lim Thi Duong, Du Duy Bui, Thuat Ngoc Pham, Chuc Ngoc Pham, Que Anh Nguyen, Hoa Anh Bui, Chi Thi Ha Nguyen, Hoan Thanh Nguyen, Bac Quang Nguyen, Kien Trung Nguyen, Dung Trung Doan, Nhiem Ngoc Dao

The microstructures and kinetics of a rich iron ore ( TFe = 65.84%) of Na Rua mine, Vietnam, used for the iron production were investigated in this study. Thermal behaviors of iron ores were well-examined by heating microscopy, thermogravimetric analysis, and differential thermal analysis. After being pelletized and then oxidatively fired at 500–1200 °C for 2 h, the pellets fired at 1200 °C (P1200) displayed a hard and dense structure with a decent compressive strength of 317.9 kg/pellet whereas those fired at 500 °C (P500) had a soft and spongy structure. The reduction of iron pellets conducted in a flow of a 60–100% CO2/ Ar gas mixture at 900–1100 °C showed significantly higher efficiency than the reduction using coal. The spongy pellets showed superior performance for the reduction in the CO/Ar gas mixture compared to the dense ones, compatible with the production of sponge iron. When mixed with an amount of coal, P1200 designed for iron production in the blast furnace demonstrated an impressive reduction activity compared to P500 and previous studies. The kinetics of pellet reduction was determined by the diffusion of substances through the solid product layers having the mathematical model of 1 − 2 3 f − (1 − f )2∕3 = kt . The microstructures of pellets during the oxidative firing and reduction were also examined by X-ray diffractometry; scanning electronic microscopy; energy-dispersive X-ray spectroscopy; and Brunauer, Emmet, and Teller method.

Jun 7, 2022

By Zoheir Khademian, Morgan Sears

According to the 2010–2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in US longwall mines were caused by roof instability. Gateroads are subjected to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many US longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the bonded block modeling (BBM) of roof by UDEC was validated against field extensometer measurements in a longwall entry roof at a 180-m depth of cover. The BBM was shown capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. Results demonstrate the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 13, 2024

By Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, José Gomes-Pereira, Inês Tojeira, Andreia Afonso, António Calado, Luísa Pinto Ribeiro

Since 2008, the Portuguese Task Group for the Extension of the Continental Shelf has been operating the ROV "Luso" (rated for 6000m depth) for geological sampling of the deep North Atlantic seabed, performing surveys on, e.g., seamounts and hydrothermal vent fields. Amongst other sensors, the ROV is equipped with a full HD video camera with which still images of the deep ocean floor are recorded. Fixed on the ROV’s frame are two underwater "line" lasers, each generating a sharp green line (532nm) over the seabed. The two lasers are paralleled and calibrated at a set distance. Provided that the camera’s angle of view is known, numerical values for seabed surface area may be calculated using direct measurements taken from the pictures containing the laser lines. We present the corresponding main mathematical formulas, which are derived from simple geometrical considerations, and discuss how to generalize these results for an arbitrary camera tilt or pan. We present an example of application of our method by estimating values for percent coverage of rock substrate versus sediment. Our results are also relevant for determining seabed polymetallic nodule abundances from still images obtained during ROV surveys.

Sep 1, 2014

By William B. Schmidt

In July of 1974 a study team comprised of the authors was formed by the Department of the Interior. It was supported in part by funding from the National Science Foundation. The purpose of this study group was to visit coal mines and research and manufacturing facilities in England and Germany, to review the status of mining in these countries, and to identify mining technology which might have application to U. S. mining conditions. The duration of the visit was 18 days. The first week of the trip was spent in England. Time does not permit a complete recitation of the team's impressions but a few of the more interesting technologic developments will be discussed. These fall into the following categories- High Speed Development Ground Support Chainless Haulage and Face Conveyors Nucleonic Steering of Shearers Miscellaneous

Jan 1, 1975

By S. L. Crouch

The general term "coal mine burp" refers to the sudden and violent failure of in situ coal. Coal bumps occur in most countries where coal is worked by underground methods, and are related to both geological factors and mining tech¬niques. Although no single set of circumstances is solely responsible for causing coal bumps, it is generally agreed that at least one of five conditions is necessary in order for then to occur: 1,2,3,4 (1) the depth of cover exceeds 500-ft., (2) the overlying strata are relatively strong and stiff, (3) the coal is structurally strong, (4) the floor does not heave readily, and (5) the mining method produces high stresses over a large area of the seam. Except for the last, these conditions relate to geological factors that are impractical to control. Consequently, methods of controlling or minimizing the occurrence of coal bumps usually are concerned with mining techniques. Coal bumps have been successfully controlled by both longwall and 'yielding pillar' mining systems 4. The longwall system is particularly effective in controlling bumps, but does not eliminate them completely, especially in strong coal seams being worked at comparatively great depths, say in excess of 2000-ft.5. Under such conditions, auger drilling or water infusion often prove helpful 5,6. These techniques are used to destress or otherwise alter the mechanical properties of the coal in an attempt to shift the peak "abutment pressure" away from the immediate vicinity of the face. Under 'normal' conditions, however, it can be expected that the coal near the face will be crushed under the prevailing high stress conditions and that the peak abutment pressure will automatically be shifted into the solid coal. In this context, coal mine bumps can be characterized as unstable releases of energy associated with successive yielding of portions of the coal seam with progressive mining. Longwall and yielding pillar mining systems are effective in controlling coal bumps because they ordinarily do not allow the zone of peak abutment pressure to become 'surrounded' by destressed coal.

Jan 1, 1973