Search Documents

By G. J. Gersbach

The Robe River Iron Ore Project began in 1962 when Cliffs International acquired mining leases in Western Australia's Pilbara Region. Initial reserves were proven and bulk ore samples sent to the U.S.A. for pilot plant testwork. Cliffs Western Australian Mining Company Pty. Limited (30%) manages the project in joint venture with Mitsui Iron Ore Development Pty. Limited (30%), Robe River Limited (35%) and Cape Lambert Iron Associates (5%).

Jan 1, 1983

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By John A. L. Campbell

Surface dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or imporve a surface dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and flocculation. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established (1). These data will be presented at a latter date.

Jan 1, 1969

By Richard Thomas Newcomb

The trend towards proportionately rising volumes of surface mining through- out the world and especially in the United States has led some observers to predict that the future of underground mining is quite limited. Certainly, the simple extrapolation of current trends1 gives evidence of a compelling sort for the hypothesis that technological progress is proceeding at a faster pace in surface than in underground mining. This paper attempts to examine the basis for these predictions by searching the historical record on differential rates of productivity as these are observed in iron ore and coal mining. In recent years economists have discussed "technology gaps" among industries or segments of the same industry, by which they mean that mechanisms for invention and its diffusion are faulty or retarded in such a way that feasible cost-cutting innovations are not applied or developed, even though technicians regard them as practical.2

Jan 1, 1968

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By F. G. Heivilin

There will be 3 billion people moving into cities by 2050. Permitting is both the biggest obstacle and the biggest opportunity for mining. The problem is not if we have the right minerals, but how we can permit and produce it in a ?Sustainable? manner. A ?Permit? and a ?Sustainable Development Plan? may soon be the same thing. How do we produce the minerals we need with: 1. The lowest possible carbon footprint. 2. Social license from community outreach by being a catalyst and not a problem in a ?Green World.? 3. Enhanced water supply during all stages of production. 4. Meeting requirements of our customers for service, quality, & cost. How important is it to have a complete ?Sustainable Development Program?? First, no plan is complete!!! It is a work in progress subject to continuous improvement. We need to work together to get the results we want. The goal of the world communities is to become carbon neutral by 2050. What is the mining community?s goal? Do we have one???? When a Clorox, Colgate Palmolive, Wal-Mart, Toyota, or Caterpillar buys a product, what are your chances of getting an order without a good program in place? The answer is it will be difficult or impossible shortly and you will be requiring the same thing with your suppliers. This is an opportunity if you are in the lead and it soon will be a necessity for most mining and processing companies requiring much extra effort to catch up. For some mines it was a necessity to get most of the SD plan to get permitted. The number of companies in the extractive industries with a full Sustainable Development Programs is expanding rapidly as shareholder demands for transparency continue to grow.

Feb 27, 2013

By Roderick Eggert, Dipesh Dipu

We look at the empirical evidence of coal block auctions in India to understand how competitive intensity affects the bid amounts in common value auctions. The results suggest that competitive intensity measured through the number of bidders for a coal block is instrumental in determining the bidding outcomes. The presence of higher numbers of bidders in the auction leads to higher bids - every additional bidder causes the bid amount to rise by INR 142.67 per tonne of coal for auctions studied for 127 coal blocks from 2014 to 2023. The paper also examines the moderating and mediating effect of competition on bids and on excess of bids from the comparative market price of coal from alternative source of Coal India Limited. The results indicate that competitive intensity does not have statistically significant impact on the relationship between common value of coal blocks and bids, neither as a moderator nor as a mediator. The strategic behavior of the bidders has also been observed as bidders have been seen to bid in a higher than market price in order to outbid the competitors.

Feb 1, 2025

By X. Tang, N. Ripepi

The Langmuir model has been widely used for the coal-methane sorption process through an isothermal test. However, even though the temperature-dependent Langmuir model was recognized theoretically and experimentally, the quantitative relationships between the Langmuir constants a and b and temperature have not been clarified and confirmed by laboratory test data. This paper collects 158 methane-coal sorption data under different temperatures that apply the Langmuir model to the relationships between the Langmuir constants a and b and temperature. Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters a and b. The results from these published isothermal tests indicate that (1) there is no consistent relationship between Langmuir constant a and temperature, (2) the Langmuir model is a temperature-dependent model whose temperature-dependent feature is mainly shown by the relationship between the Langmuir constant b and temperature, and (3) the relationship between the Langmuir constant b and temperature can be described by both exponential and linear relationships with dried coal. This paper provides a database for the temperature-dependent Langmuir model that can be used for the reservoir simulation of coalbed methane reservoirs and for the coal seam degasification modeling of underground coal mines, considering the heating effects induced by geothermal and heat injection through factors such as hot water, hot steam and ultrasonics.

Jan 1, 2016

By Daryl R. Tweeton

The Bureau of Mines measured the geochemical changes as H2S04 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen, HC03, U, V, Na, K, Ca, Mg, SO4, C1, Mo, Mn, Fe, Al, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By S. D. Irons

With the passage of recent national and state legislation aimed at tighter regulation of air pollution and smoke control, attention has been focused on a problem which has long confronted the coal industry--the disposal of coal waste with its inadvertent ignition. Even as recent as 1935, a decision from the Allegheny County Court of Common Pleas confirms the stand taken on control of burning coal refuse disposal areas. "The uncontroverted testimony is that there is no feasible method of operating a coal mine without a gob pile on the surface, as no use has ever been found for this troublesome by-product of mining; that every large coal mine has a large gob pile close to its tipple; that sooner or later these piles all ignite through spontaneous combustion; that practically every large mine in Western Pennsylvania has a burning gob pile, and that there is no known means of averting such a fire." 19* As a result of the past "no regulation policy," there are presently on the order of 500 burning refuse banks, of which 213, 142, and 49 are found in West Virginia, Pennsylvania, and Kentucky, respective¬ly. 18 Many of these refuse banks have burned for 40 years or more; many others may continue burning for a like period. It is estimated that the annual emission from these smoldering piles approaches 183,000 tons of pollutents which may produce many deleterious effects on the populace, property and vegetation in the proximity to the sources.16 To date, little progress has been made in alleviating the pollution from the currently burning refuse banks; however, numerous investigators who are researching the causes of ignition, as well as preventative disposal techniques (refuse compaction, layering and crushing to finer sizes) have met with some success in handling the newly discarded coal refuse.

Jan 1, 1967

By Tim M. Benson, Adam L. Lamanna, Carolina Martinez-Gutierrez, Mark J. Stephani

The Lower Concourse C Extension (LCE) 108-in Storm Sewer consists of a 2,797-foot long, 27 to 55-foot deep, 108-in I.D. storm sewer tunnel. Situated beneath active taxiways and a terminal apron at Hare International Airport (D), the tunnel diverts ows from existing storm sewers located within the footprint of a future satellite concourse. The project was delivered via Construction Manager at Risk (CMAR) as part of Chicago Department of Aviation’s (CDA) ongoing O’Hare 21 Capital Program. This paper presents project details, multiple stakeholder coordination, subsurface risks and challenges, TBM performance, and impacts to existing infrastructure.

Jun 23, 2024

By Howard M. Wells

Portfolio theory and the Capital Asset Pricing Model (Modigliani and Pogue, 1974) provides an investment decision rationale which takes account of the benefits of diversification in reducing effective risk, but this theory does not consider the financial capability of the firm to survive large losses if they should occur. The LL-curve theory (Wells, 1976) takes the latter consideration into account, but it does not provide for the effects of diversification. This paper pro- poses a general theory to account for both diversification and the financial capacity of the firm to underwrite the investment risks.

Jan 1, 1983

By Jorgen Elbrond

The capacity calculation of complex transportation systems involving variable activity times such as encountered in the mining industry are often worked out by means of simulation, which reconstructs waiting times and cycle times. The queuing theory, which mathematically calculates waiting times, has been used mainly to describe the, phenomena. This is due partly to the difficulties encountered in modelling complex systems and partly to the difficulty of reconciling the required time distribution laws with the real phenomena by means of the queuing theory. It is, however, obvious that formulas for capacity calculations would be preferable to simulation procedures because of their higher calculation speed, shorter and more flexible programs and shorter programming work. The calculation procedure presented in this paper is composed of some rather simple models, which are based on the queuing theory, and on some probabilistic and some deterministic considerations. The models are supported by observations, and to some extent by simulations. It has been attempted to find all the components of the cycle time and to include them in a comprehensive model. It is the intention to demonstrate that even quite complex mine transportation systems can be treated by means of the queuing theory with the advantages mentionned above and, without sacrificing the precision of the estimates. The speed of calculation of a wide range of parameter combinations is such that the procedure can be used extensively by a project engineer in the search for optimal modifications of the entire transportation system.

Jan 1, 1979

Contents

Jan 1, 1985

By Thomas E. Finch

Engineering mine design encompasses a range of situations, and each situation has its own range of detail and fineness. The most time consuming, and perhaps repetitive design situation involves evaluation of new or alternate mining methods. Many man years are consumed examing alternatives conjured up at all levels of the design team, from the number crunching engineer to the engineering manager. Many alternatives are intuitively disregarded, some are briefly evaluated and thrown out, and many others are started but not completed due to time constraints. All alternatives have similar input characteristics and evaluation procedures. In the design process, production requirements are known and equipment production capabilities are generated to determine the numbers and costs of an equipment type required to match a given situation. The end result is some comparative figure, typically cost per ton or yard upon which a decision is built. The similarity of input data and problem solving techniques lends design to computer solution. Computer aided equipment evaluation is not new to the mining industry. An existing and accepted technique is exemplified with the programs used by truck manufacturers. Given a haulage profile and production requirements, the number of anyone capacity, horsepower, tire size, gear ratio or similar characteristically identified truck can be determined. This information can be outputted in varying degrees of complexity and the results used with equally varying percentages of credibility by design or production engineers. Most engineers are willing to accept-the computer's effort with relief and a desire for belief. Although inherently more complex, the ultimate end of computer manipulation should be total mine design. This is an extremely large step in the evolution of mine design, and not many engineers, including the authors, believe the results would be directly applicable or necessarily correct. As with computer simulations of an operation, total computer design of mines requires such complex and lengthy input that each mine might be manually designed more quickly and cheaply. The existence of computer programs which initially evaluate a mining system or part of the system is upon us, however.

Jan 1, 1978

By Robert W. Row

The run-of-mine coals in the U.S. being fed to coal cleaning plants have become increasingly finer due to the adoption of modern, mechanized mining methods, and economics are dictating that finer fractions, as well as the coarser fractions, be cleaned. Traditional dewatering methods (vacuum disc filters and centrifuges) are proving inadequate for preparing fine refuse for disposal or fine coal product for downstream handling. The Electric Power Research Institute has been supporting research into the nature and limitations of mechanical dewatering, and novel ways of improving it. The efficiency of various silicone-based chemicals at aiding dewatering was investigated, and it was shown that the final moisture content of hydrophilic coals after vacuum Filtration could be reduced by 1 to 5% with up to 40% increase in filtration rate by addition of one of several of these silicones. EPRI also has an on-going program at its Coal Cleaning Test Facility to investigate the performance of the Larox pressure filter in comparison with that of the disc filter and solid bowl centrifuge. While improvements to the dewatering performance currently being obtained in existing operating plants by such means are achieveable, a fundamental study has shown that, regardless of changes in operating conditions, there may be a limit to the lowest cake moisture content attainable by mechanical dewatering of a given sample of coal fines. Determination of this limit for a specific coal would be useful in designing facilities to dry and handle it.

Jan 1, 1984

By Bernd Hagenah, Katie Theis, Cristina Lauzon, Petr Pospisil

Lidding over or tunneling existing transportation infrastructure is currently under review in several U.S. cities. The main reasons for this are the use of the created space for urban development, the reduction of noise and exhaust fumes for the residents, and, thus, a significant increase in the quality of life. The main aspects to be considered during the planning process are (1) total investment and operational costs, (2) impact of construction works on current traffic, (3) safety and fire protection, and (4) socio-environmental issues. The paper presents some basic planning principles, and experiences of recent urban highway coverages are shared.

Jun 23, 2024

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By A. M. Radigan, W. G. Prast

M.S. Azun The authors' paper did not explain the facts and reasons why state companies are established and what their role is in international industrial mineral trading. Also, I do not agree with the conclusion implying that the main goal for state companies is to capitilize natural resources. Almost all state companies are founded by certain laws and their activities are arranged by state regulations. Their only aim is to operate mineral deposits for their people and to protect the rights of the people. Although some ore deposits, such as nonstrategic or small, may be exploited by privately owned companies, the state has the right to control the operation and production. Activities of state companies may or may not be widened because of the character of the deposits and the importance of the mineral market involved. For some countries, although governments may occasionally change hands, the policy of the mineral trading system is not affected by this change. There is no doubt that any government desires to make more earnings to increase GNP, when it is involved in operating and trading mines. It wants to produce and sell the finished products, instead of unprocessed ones, if possible. When it is known that some mineral deposits are relatively rare, such as Turkish boron deposits, the government can nationalize the mines to control production and affect the market. If there is an abundance of a certain mineral in the market, the government can cut production and set a floor price, such as Canadian potash. Also, when production of a specific mineral is unique, such as Turkish chromite, the price of such mineral may be set by correspondant government. One may add that if some governments with their state companies produce a certain mineral in a larger amount, they may decide to establish a cartel to protect their production and price. These are the facts followed by government-owned state companies and partially government-owned companies. The reason being charge of many deposits by the state companies is always the same: "protect" the mineral rights of the people.

Jan 2, 1984