Search Documents

By Randy Fulton, Ignacy Puszkiewicz, George H. K. Schenck

Stuart Olson Construction, Inc. excavated 385m (1263 ft.) long twin tunnels with 6.25m (20.5 ft.) O.D., a portal and a cross-over for the Edmonton, "Metro". The work for Contract No. 76458, SLRT South Tunnel and Portal, in Edmonton, Alberta, Canada was performed in 1989 and 1990. NATM was specified because of the instability of glacial deposits. The contractor decided to use "two firsts" on this project: Fully mechanized NATM and a novel excavator¬mounted tunneling machine. An excavator was equipped with a cutter boom, and a loading and conveying system. This novel machine cost only about one-third of the price of a special NATM roadheader. This new combination of NATM and an excavator-mounted cutter boom offered a cost-effective alternative to shields, slurry TBMs and roadheaders for short tunnels in unstable ground. For NATM tunneling in hard rock or in mixed faces, the roadheader-type cutter boom can be replaced with an impact hammer (hydraulic breaker).

Jan 1, 1993

By James M. Murphy

INTRODUCTION In the fall of 1983, the fourth new Rapid Transit System constructed in this country in the last forty years will go into revenue service. The Baltimore Metro will bring to this major Mid-Atlantic seaport the first phase of a planned intermodal transit system, serving a metropolitan area with a population in excess of four million people. Originally, the Mass Transit Administration (MTA) considered construction of a twenty-eight mile system known as Phase 1. Its two lines would run from the center of Baltimore City, one going northwest to Owings Mills and the other south to Anne Arundel County. Legislative approval was granted in April, 1976; however, funding was limited to constructing a segment fewer than eight miles in length, along the northwest corridor from Charles Center to the Baltimore City county line. This segment is known as Section A. The project is 80% federally funded and 20% state funded, with a capital cost estimate of $797,000,000 to complete. This report addresses the development and implementation of a Coordinated Insurance Program for the construction phase of Section A, and includes a description of the associated risk management process. GENERAL DESCRIPTION OF SECTION A Section A of the Baltimore Metro is composed of a rapid transit line eight miles in length which serves the northwest corridor between Charles Center in downtown Baltimore and Reisterstown Plaza at the Baltimore City county boundary. The line is completely grade separated and, once operational, will provide high speed automated rapid

Jan 1, 1983

By I. Koliabina

In this paper, the results of mathematical modeling of casing pipes decontamination from radio-active new mineral forms directly in boreholes using hydrochloric and hydro-silicic-fluoric acids are presented. Modeling for highly and low radioactive coatings on the walls of casing pipes of Anastasievka oil-and-gas deposit was performed using GEMS software, based on the method of Gibbs energy minimization. Calculations have shown that thorianite and goethite, that are present in low-active crusts, detected in casing pipes uplifted from comparatively low depths, are well dissolved in hydrochloric acid, but radiobarite is almost insoluble. For the same acid concentrations, almost all radiobarite of high-active coatings detected in pipes uplifted from considerable depth is dissolved. To evaluate the possibility of decontamination of pipes from radiobarite of low-active coatings, modeling of crust dissolution under the action of H2SiF6 has been performed. The results have shown that for acid concentrations of more than 13 % almost all Ra and Ba are dissolved while all iron and thorium remains in goethite-thorianite solid solution. For the same acid concentration, almost all radiobarite from high-active coatings is dissolved. Therefore, no reagent allows decontamination of pipes from coatings of both types. It seems that successive or simultaneous use of both reagents (HCl and H2SiF6) in certain ratio is required. To clarify this issue, further experimental and model investigations are necessary. The issue of decontamination of casing pipes from galena that is present in high-active crusts also needs to be clarified.

Jan 1, 2005

By Paul J. A. Lever

The mine environment is dynamic and operating conditions change continually and are difficult to predict. New equipment, variable geological conditions, modified layouts, and different equipment operators make monitoring and control system difficult to apply without continual software maintenance. The paper reports on algorithms that were developed, encoded with Knowledge Craft Tools, and tested on underground coal mine data to adapt to the dynamic environment. The system receives data from sensors in near real time and then identifies patterns in the data. Using a set of mode features the data is automatically checked to determine the present operating mode. When the operating mode changes from the previous shifts, the system automatically learns the new mode characteristics and uses that mode context for further data analysis. The concepts presented in this paper are applicable to a wide variety of mining scenarios, not just underground coal mining.

Jan 1, 1992

By Eli Curiel, Ingar F. Walder, Patrizia P. Schuster, Walt Keyes

Mansfield Canyon, of the Wrightson Mining District, Santa Cruz County, Coronado National Forest, Arizona, was actively mined in the late 1800's and early 19001s, with minor activity until 1953. The main products were lead, silver, copper, zinc, and gold occurring in polymetallic quartz veins. The canyon contains numerous adits and waste dumps, some of which generate metal-loaded acid. Samples of seeps, waste dumps and bedrock have been collected for various analyses: metal concentrations, acid base accounting (ABA), and water quality to evaluate the extent of oxidation and metal release from the start of mining until present, the potential impact, and reclamation options. Although the waste-rock piles within the canyon are small (2,000-10,000 tons), they have a high sulfide content with little or no neutralizing capacity. It is planned, therefore, to move the waste piles either to a constructed repository site within the canyon or to a copper leach facility to be used as an acid generator.

Jan 1, 2000

By C. Milne, T. M. Dyhr, T. E. Wilson

As time progresses, new concerns regarding long-term post-mining effects are identified, increasing mine closure costs. Regulators responding to public interest must take a “worst case” view and require post-closure monitoring or remediation processes. Although closure costs depend on the size and type of operation, general cost categories are defined, and median values (per acre, or per unit of production) are identified. Closure cost categories, as well as amounts, have increased with time. Except for increased efficiency in earth-moving and water management (surface or subsurface), there are no apparent offsets to a steady rise in closure costs. When the historical trend of closure costs is considered, it is probable that additional cost categories will come into being. For mine operators, the challenge will be to anticipate them and devise cost-effective remedies.

Jan 1, 2003

By W. F. Kane

Underground geologic mapping is an extremely important aspect of any on- going ground control plan. However, the actual use of data derived from such a program is difficult and often leads to subjective analysis. In this regard, computer software has been developed that utilizes a statistical determination of unstable ground conditions based on geomechanical and operational data and collected by mine personnel on a mine-wide, or regional basis. Categorical variables, such as faulting or joint frequency, are selected from local experience to form the framework of a representative data base. Statistical comparisons between the selected variables and a particular ground control problem are conducted and correlations subsequently made. The probability of encountering unstable conditions in virgin areas is assessed as information from these regions is gathered. This data can be derived from surface mapping, cores, and/or geophysical logs. As mining progresses, new data is merged with the existing data base to form a more comprehensive and extensive unit. The advantages of this approach and the acquisition and maintainence of a large data base include the more accurate representation of existing mining conditions, increased confidence in analyzing future problem areas, and elimination of the difficulties which arise when using ground control theories derived for other, often very different, locales.

Jan 1, 1986

By Robert Sutton, Milan Sjaus

Conveyor pulleys are an important and integral component of a conveyor. Conveyors work in sequence to make up conveyor systems. Each conveyor system is only as reliable as its crudest component. If the pulley fails, then the whole material handling system stops. So what is the effect of this downtime? What are the costs of repair? How much are we willing to pay to solve the problem? What should we spend to prevent an unscheduled shutdown? Do we use the technological improvements at our disposal or do we ignore them to satisfy immediate cost savings? This study will focus on the cost of pulleys relative to the total conveyor cost, the cost of downtime, the maintenance costs and the costs for resolution of the problem. Some philosophic and design concepts are injected for illustration and discussion.

Jan 1, 2000

By M. Kumral

The in-situ mineral characteristics of a deposit are simulated by sequential co-simulation and averaging the simulated characteristics within specified block volumes creates a three-dimensional block model. This model is then submitted to optimal open pit and production scheduling algorithms. As the market values of industrial minerals depend on the satisfaction of predetermined blending criteria rather than metal content, a Linear Programming (LP) scheme has been used to identify all blocks that can be included in the blend without violating the grade requirements. The Lerchs-Grosmann algorithm using the blocks identified by the LP program determines optimal pit limits. All blocks that lie outside the optimal pit are removed from the system and the blocks within the optimal pit are submitted to the production-scheduling algorithm. Production scheduling optimisation is done in two stages: Lagrangean parameterisation, resulting in an initial sub-optimal solution, and multi-objective simulated annealing (MOSA) improving the sub-optimal schedule further.

Jan 1, 2002

By A. W. Khair, M. Ahmad

Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion, oxidation, or diffusion, depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been camed out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation.

Jan 1, 1992

By P. Bevilacqua, G. Ferrara

The paper discusses the problem of accuracy in the determination of the partition curve of gravity separation processes, which is strongly affected by both the sharpness of separation of the density analysis system used and the width of the density range selected. The problem is important when the density analysis of the separation products cannot be performed using heavy liquids, but has to be performed using heavy suspensions or using other systems such magnetogravimetric separation. The imperfect separation given by these systems and the use of large density ranges lead to the determination of apparent partition curves instead of actual partition curves for the process. In the paper the relation between apparent and actual partition curves is studied under different conditions through a simulation program. For different input data, special diagrams are given which, once the apparent partition curves and the sharpness of the density cuts are known, allow calculation of the actual partition curves and the related parameters.

Jan 1, 1995

By J. Pang, S. Chander

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and impedance spectroscopy techniques. The cyclic voltammetry was used to elucidate oxidation/reduction reactions, whereas impedance spectroscopy was used for in-situ characterization of the interface. To analyze the impedance spectra, equivalent circuit models were constructed based on a layer- wise growth of reaction products. Parameters of the equivalent circuit were calculated by comparing the experimental spectrum with that expected on the basis of equivalent circuit. From the value of equivalent circuit parameters, properties of the surface layers were inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution. From such changes the effect of oxygen and collector concentration on the contact angle and flotation behavior of chalcopyrite were interpreted.

Jan 1, 1991

By B. Ainsworth

The 1972 discovery of the Howards Pass lead-zinc deposit was the product of systematic regional geochemical surveys used to evaluate conceptual geological models for the metal-rich black shales of the Selwyn Basin. Motivation of personnel involved in all aspects of work was as critical a factor to the success as the existing corporate attitudes and infrastructure. Exploration programs were flexible but maintained a focus only on targets of sufficient economic potential to support operations in remote locations. Direct costs for the programs that lead to the discovery were in the order of $500,000 (Canadian 1972). Geological reserves today stand at over 500 Mt (511 million st) of 7% combined lead-zinc, containing a higher grade zone of nearly 10 Mt (11 million st) of 16% combined lead-zinc.

Jan 1, 1991

By S. P. Banerjee

There has been a phenomenal increase in production of coal from opencast mines in India. At the same time environmental problems caused by mining are receiving greater atttention. Deterioration in ambient air quality due to increased concentration of suspended particulate matter (SPM) in and around an opencast project is a major problem. Some measured values of SPM level around opencast mines in diff coalfields show that in many cases the TLV of 500 ug/m^3 is exceeded. The impact of dust emission from a mining project on surrounding areas are estimated by using computer models for air pollution dispersal but such treatment suffers from errors in predicting the dust load and failure to take into account the terraced nature of the opencast mine site. The haul roads have been identified as the most prolific source of dust and some recent trials on haul road dust consolidation in Indian mines are mentioned in the paper. Statistics regarding pneumoconiosis cases in Indian coal mines for the last decade are presented to show an increase in reported cases and a gist of the recently amended regulations on the subject of precaution against dust is mentioned.

Jan 1, 1991

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The term unsaturated flow refers to the conditions in which soil pores are filled partially with water and partially with air. This situation constitutes a porous material filled with immiscible fluids. Immiscible fluids by definition exhibit a distinct interface when in contact with each other resulting in a pressure discontinuity across the interface due to surface tension. The fluid that tends to wet the solid particles is called the wetting fluid and the other is the nonwetting fluid. In the air-water sys- tem, air is the nonwetting fluid and water is the wetting fluid. A somewhat analogous fluid system is that in a petroleum reservoir in which there may be up to three immiscible fluids-oil, salt water, and natural gas. The degree of wettability of the fluids is salt water + oil + gas. That is, salt water is the wetting fluid at any interface and oil is the wetting fluid at an oil-gas interface but is the nonwetting fluid at a water-oil interface. Since the oil-water and air- water systems are similar, much of the theory and methods of analyses for the air-water system or unsaturated flow have evolved through the petroleum literature. In the two-fluid system the pressure difference across an interface depends on the size of the pore space in which the interface occurs. The equation commonly used to represent this dependence is

Jan 1, 1986

By Leslie S. Halasz

This paper describes the techniques implemented at Randfontein Estates to develop twin-haulages at 'high speed'. An operation which culminated in the world record advance for twin-end multiblast cyclic development in hard abrasive quartzites. A major expansion project was planned for the mine, with the sinking of a third twin-shaft system (to be known as Cooke No. 3), to raise the level of ore production from 3 500 000 to 5 000 000 tonnes per alumm. Subsequent redesign of the proposed shaft system as a single 9 m brattice wall shaft took place, reducing the planned shaft sinking period by 12 months and saving an estimated R 250 000 (U.S. $ 330 000) in sinking costs. The advancement of the Cooke No. 3 Shaft sinking and development programme necessitated a rapid excavation schedule for two interconnecting twin-haulages from the existing Cooke No. 2 twin shaft complex to provide a second means of egress. An early holing between the two shafts would provide significant financial and technical benefits. Pre-development and equipping of shaft pillar excavations would enable a rapid shaft production build up and blocking out of at least one year's ore-reserves.

Jan 1, 1983

By J. A. Herbst, K. N. Han, P. B. Queneau, S. W. Asihene

As hydrometallurgy matures as a technology, more of its existing process knowledge will continue to be summarized in the form of detailed mathematical models. This development is happening at a time when major improvements in computer hardware have reduced the cost of computing. The opportunity then exists, through the solution of these process models, to design, control, and optimize hydrometallurgical plants on the basis of the physics and chemistry of its processes and less on empiricism. In this paper, a review of the current capabilities of sensors and phenomenological models for selected hydrometallurgical processes is presented. Future trends, in terms of the control and optimization of hydrometallurgical plants, are then explored. The possibility of simultaneously optimizing plant design and associated process control system performance is discussed.

Jan 1, 1993

By Alex Harrison, Steve Kasper

Various countries around the world have testing and manufacturing standards in place for steel cord belting. These standards are very comprehensive in what they allow the end user to specify, however, their practical significance in terms of belt life is more difficult to quantify. Such testing standards will be briefly reviewed in this paper in relation to the implication for end user expectancy. Since there is no US standard of manufacture, the end user is left with writing their own specifications. In addition, such standards do not address the effect on belt life of manufacturing faults, such as cord plane buckles, or lateral cord movement. Some new technology used to test steel cord belting will be described as an aid to both manufacturer and end user. Specific end user related issues addressed on this paper are: Tracking and belt quality Cord plane irregularities and performance Cord size and belt life Cord fatigue and testing

Jan 1, 1993

By B. J. Arnold

With the passing of the 1990 Clean Air Act Amendments, many utilities are opting to switch to lower sulfur coal to meet new SO2 emissions requirements. This lower sulfur coal may be from new suppliers or it may be from current suppliers that modify existing cleaning plants or build new plants to produce this higher quality coal. New, sophisticated coal cleaning simulators are useful tools for optimizing cod cleaning circuit operating parameters to maximize the production of clean coal that meets more stringent specifications for SO2 emissions potential. The examples in this paper were developed using the Coal Cleaning Simulator (CCS), running under ASPEN PLUS™, that was developed under a Department of Energy project cosponsored by the Electric Power Research Institute. With advanced sensitivity analysis and optimization features, CCS allows a quick, efficient, cost-effective review of coal cleaning plant performance to meet current production goals and to plan future changes in plant operating parameters or circuitry configurations.

Jan 1, 1995

By F. Aurelian

The Banat district in Romania was an important uranium mining area for the last 45 years until its closure in 1997. Uranium was present as finely dispersed pitchblende into solid bitumen lens and layers. Due to the mining activities, radioactive wastes have been disposed of in different places of the Banat area. These sites contain uranium, radium and radon and exhibit high contamination potential for environmental receptors (soil, air, waters, sediments and vegetation). Therefore the risk for human health through external and internal irradiation is considered high. The main pollution sources in this uranium mining area are mine and surface waters, waste and low grade ore heaps, dumps as well as release of radon. In this paper studies concerning recognition of pollution sources, delimitation of maps, uranium and radium solubilization and migration from dumps as well as environmental contamination of specific areas related to exploitation and exploration are presented. The risk assessment is based on the relationship ?source-pathway-target? in order to assess environmental risks and identify targets for rehabilitation. The sources causing significant contamination problems were identified by examining the pollutant linkage. The remediation plan for the Banat uranium mining complex involves mine flooding, treatment of water and leachates, as well as modification of heap slopes, application of covers and establishment of vegetation.

Jan 1, 2005