Search Documents

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By T. M. Louw, L. Auret, S. M. Bradshaw, F. F. Noelle

Modern industrial processes undergo frequent process state shifts due to changes in demand, feedstock or maintenance operations. Multimodal continuous process monitoring is therefore required for effective plant operation. Steady state analysis is a key component in effective multimodal monitoring. Various issues still remain in determining the starting and ending times of transition states. High dimensionality of process data is a characteristic that makes it difficult to select variables to consider when conducting steady state analysis. In order to address these problems, steady state detection on the principal component space is proposed. First, data undergoes principle component analysis to reduce dimensionality, then existing multivariate steady state detection algorithms are applied on the principle component scores. A novel algorithm, threshold PCA-SSD, is proposed and compared to an existing technique for steady state detection. The algorithms are investigated on high dimensional synthetic data Keywords: Multimode process, steady state detection, principle component analysis

Jan 1, 2020

By G. E. Blight

Several aspects of the behaviour and properties of backfills consisting of cemented cyclone underflow tailings are illustrated by means of examples, and guidelines are given on the optimization of the performance of cemented fills. The stretch characteristics of the geofabric used to contain freshly placed backfill are described, as well as the relationship between these characteristics and the forces acting on retaining barricades. The properties required to achieve a self-supporting, stable free face in cemented backfill are explored, and a graphic relationship between stable height and shear strength is presented and compared with that for uncemented (classified) tailings. After a description of the characteristics of Witwatersrand quartzite gold-tailings backfill and commonly used cements, the process of drainage and air entry into backfill is outlined. Following this, the early-age gain in strength and the shear-strength characteristics, as well as the compressibility characteristics of cemented backfill, are described. Two phenomena that are potentially damaging to cemented backfill are seismic effects (or blasting acceleration) and the closure that takes place during the curing of cement. Investigations show that neither of these phenomena is actually significantly deleterious to gold-tailings backfill: liquefaction does not Occur as a result of seismicity, and hydration of cemented fill is not significantly impeded by closure.

Jan 1, 1996

By A. J. Reynolds

In recent years, rapid depletion of the higher grade reserves, allied to decreases in paylimits, has led to the exploitation of secondary, erratically mineralized placer horizons on various marginal and low grade gold mines. On Blyvooruitzicht Mine, the rich Carbon Leader Reef has limited reserves, necessitating exploration of the lower grade Middelvlei Reef. This placer has always presented evaluation and exploration problems, to such an extent that it was, at one stage, considered uneconomic. Despite an extensive underground drilling programme no ore reserve targets of reasonable size were apparent. However, when a certain degree of parallelism between sedimentological trends in the Middelvlei Reef and the underlying Carbon Leader was recognized, a meaningful exploration model could be developed. Firstly, all historical sampling records for the Carbon Leader were entered into a computerized system; the database comprised in excess of 340 000 data points. Variables captured consisted of gold value, uranium value, con- glomerate thickness and total reef thickness. The raw data were then averaged into blocks, and plots of different variables were computer-generated for further analysis. This enabled the Carbon Leader to be modelled sedimentologically and, thereby, exploration targets for the Middelvlei Reef were generated, based on the Carbon Leader facies trends. Geostatistical analysis of sampling data in exposed areas of the Middelvlei Reef underground has confirmed the sedimentological breakdown of the placer into distinct facies areas. A facies model relating value distribution patterns to depositional trends, both for the Carbon Leader and the Middelvlei Reef, has thus been incorporated into a mine planning strategy.

Jan 1, 1987

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best `grade descriptor' is discussed.

Jan 1, 2007

By Jürgen Antrekowitsch, Harald Osthof, Stefan Steinlechner

"In the case of feasibility assessments or feasibility studies, an important point of discussion is often how to calculate the capital (CAPEX) and operating expenditure (OPEX) of a plant. Generally, there is also the request to know how the CAPEX varies when the size of the plant is increased. Nowadays, many databases give an indication of specific equipment costs in relation to the production rate. These data are based on cost information from equipment suppliers and have to be continuously updated by the owner of the database. The approach presented here is a model which allows sizing of process equipment, for example a leach tank, based on process data in combination with the calculation of mechanical properties. Furthermore, it calculates the CAPEX based on construction material cost and adequate machining surcharges. Thus, a single cost model for a leach tank is adequate for both copper and other hydrometallurgical plants and stays valid with changing construction material prices. To summarize, the advantage of this model is the more versatile approach and thus the flexibility due to the inclusion of design aspects, process and mechanical engineering aspects and an updatable database. The database, which is in regard to material cost and is the basis for the cost estimation, is easily updatable from commonly accessible data. This model thus approaches the procedures of an engineering company when designing a plant and executing a cost calculation. INTRODUCTION Hydrometallurgy nowadays plays an important role in processing of primary and secondary resources. In copper metallurgy, hydrometallurgy accounts for roughly 20 % of worldwide primary production, especially in the case of oxide or low copper-containing ores. Zinc smelters changed their method of production from a pyrometallurgical-dominated concept decades ago to mainly hydrometallurgical routes today. Gold production processes using leaching, especially, have a long history without any development which would not be competitive if not based on hydrometallurgical concepts (Pawlek, 1983; Winnacker-Küchler, 2006)."

Jan 1, 2015

By M. Seerane, R. Machaka, P. Ndlangamandla

"Metal injection moulding (MIM) is a near-net-shaping powder metallurgy technique suitable for the cost-effective mass production of small and complex components. In this paper, the effects of the metal powder particle size on the final properties of 17-4 PH stainless steel are reported. Three different particle sizes (d50 33.0, 7.91 and 4.04 µm) were used to prepare the injectable MIM feedstocks using a CSIR-developed wax-based binder system at a fixed solids loading of 60 vol.%. The distribution slope parameter and the rheological flow index behaviour were used to predict the flowability of the feedstocks. The effects of the particle size on MIM products were established. The results are discussed in terms of the subsequent microstructural and mechanical properties of MIM 17-4 PH stainless steel against the established MPIF Standard 35. IntroductionMetal injection moulding (MIM) is a near-netshape manufacturing process established as an alternative to produce complex small-tomedium shaped components that were previously fabricated by conventional methods at higher costs (Attia and Alcock, 2011; Todd and Sidambe, 2013).Although recent advances in micromanufacturing (mainly machining and electrodeposition-based) have enabled the fabrication of complex micro-size geometries directly into miniaturized parts, these processes are generally neither routine nor easily accessible at present (Attia and Alcock, 2011).Typically, the MIM process consists of four steps: mixing, injection moulding, debinding and sintering. Mixing involves blending of the desired metal powder composition with carefully selected multicomponent organic binders at the right proportion. This mixture, which is called feedstock, is then injected into a mould of a required shape to form a ‘green part’. Debinding is the removal of the binders by chemical, thermal, or catalytic means while maintaining the shape of the part. Finally, the debound part is sintered to a full or near-full density part (Sotomayor, Varez and Levenfeld, 2010). The MIM process is essentially a combination of plastic injection moulding with conventional powder metallurgy technologies."

Jan 1, 2016

By J. D. Zhou, F. Yang, X. G. Bi

"In this investigation, the phosphorus distribution ratios in the CaF2 system and B2O3 system dephosphorization slags for high-phosphorus hot metal pretreatment were measured by an indirect method under laboratory conditions. Firstly, the phosphorus distribution ratio between liquid slag and solid iron was measured, and then the phosphorus distribution ratio between liquid slag and hot metal was calculated. Phosphorus capacity was calculated in terms of the composition and optical basicity of the slag. Dephosphorization slag was also studied by scanning electron microscopy, energy dispersive analysis, and X-ray diffraction analysis. The experimental results show that the phosphorus capacity of the B2O3 slag system is much greater than that of the CaF2 system. It is demonstrated thatB2O3 can completely replace CaF2 as fluxing agent for high-phosphorus hot metal pretreatment. With CaF2 as fluxing agent, the phosphorus capacity increases with increasing CaO content in the slag, but the phosphorus distribution ratio decreases. B2O3, when used as fluxing agent, can react with high melting point phases such as 2CaO·SiO2 and 3CaO·P2O5 in the slag to form new phases with low melting points such as 11CaO·B2O3.4SiO2, 2CaO·B2O3.SiO2, and Ca9.93(P5.84B0.16O24) (B0.67O1.79), thereby acting as a fluxing agent. When the ratio of w(B2O3)/w(CaO) is 0.16, the phosphorus distribution ratio reaches its maximum value, that is, the dephosphorization ability of the slag is at its maximum. IntroductionAs international iron ore prices continue to rise, the development of China's steel industry is facing a lot of pressure. Against this background, development and utilization of domestic high-phosphorus iron ore resources is particularly important. When highphosphorus iron ore is used in ironmaking, the phosphorus content in the hot metal can reach 0.35% or more, and the hot metal must be pretreated. For hot metal with 0.08–0.10% dissolved phosphorus, the traditional hot metal dephosphorization pretreatment technologies are relatively mature. However, when using these methods to dephosphorize hot metal containing 0.35% P or more, the amount of dephosphorization slag can reach 100–150 kg per ton of hot metal. Furthermore, the traditional dephosphorization methods require the addition of large amounts of CaF2 as fluxing agent, and this results in high fluoride levels in the dephosphorization slag. The fluorine in the slag can partially dissolve in water and thereby causes high fluoride concentration in the water and soil. Once the fluoride is absorbed by humans or animals, it can result in toxic effects on the central nervous system and myocardium. In addition, fluoride can accumulate in the environment, and thereby pose a health risk to animals and humans through the food chain (Li, 2007; Liu, Wang, and Dong, 2011, Diao, 2013). The objective of this research is to replace CaF2 with B2O3 as fluxing agent while achieving the expected goals of hot metal pretreatment."

Jan 1, 2016

By Z. L. Xue, J. L. Li, X. Y. Wang

"In low-carbon energy-efficient basic oxygen furnace (BOF) steelmaking processes, limestone partly or completely replaces the active lime. The effects of limestone calcination temperature (1200–1500°C) and time (5–15 minutes) on lime reactivity and CaO grain size were investigated. The reactivity was evaluated by titration with hydrochloric acid, and the CaO grain size was analysed using scanning electron microscopy. The results revealed that for calcination temperatures higher than 1300°C, the reactivity reached a maximum and then decreased . The higher the temperature, the earlier the peak of reactivity appears. The CaO grains grow with increasing temperature and time, which leads to the decrease of reactivity. Notably, the effects of temperature on CaO grain size and reactivity are more marked than that of time. To obtain active lime calcined at ultra-high temperature by flash heating, the calcination conditions should be 1300–1400°C for 10–15 minutes, or 1400–1500°C for 8–10 minutes. IntroductionLime is one of the most important slag-making materials for dephosphorization and desulphurization in the basic oxygen furnace (BOF) steelmaking process. The reactivity of lime is a measure of its capability to take part in slag-making. Lime having a reactivity of more than 300.0 mL (4 N HCl), determined by hydrochloric acid titration is generally referred to as active lime (Rusjan et al., 2007; Zeman, 2008). At present, the active lime used for BOF processes comes primarily from a kiln or shaft kiln, where limestone is preheated at 700– 900°C, and then calcined at 1050–1200°C (Drenhaus et al., 2010; Oates, 2007)."

Jan 1, 2016

The annual General Meeting of the Branch was held in the St. Helena Club on Wednesday, 4th August, 1971 at 8.00 p.m. Mr N. A. Honnet (Immediate Past Chairman) was in the chair. There were also present Mr V. C. Robinson, President of the South African Institute of Mining and Metallurgy. Nine Fellows: Messrs J. R. F. Handley, C. J. Isaac, J. Lorenzon, J. M. Meyer, C. Mostert, D. A. Smith, S. L. S. Swart, I Thomas and R. G. Williams. Five members: Messrs R. Campbell, A. H. Edwards, K. Pearce, G. P. Rundle and R. B. Sutherland. Five graduates: Messrs J. E. Andrews, E. J. Shillaber, M. H. Smith, T. R. Stromsoe and D. J. van Niekerk. Two associates: Messrs A. Paschalides and D. S. Robinson. Eight visitors. Total present: Thirty-one. MINUTES OF THE PREVIOUS GENERAL MEETING As the minutes of the General Meeting held on the 16th June, 1971, had not been published in the Journal, the Chairman moved that the adoption and discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. The minutes of the General Meeting held on the 10th February, 1971, were taken as read. The adoption, which was proposed by Mr D. A. Smith and seconded by Mr J. M. Meyer, was carried unanimously. At Mr Honnet's request, Mr V. C. Robinson took the chair during the presentation of the Chairman's Annual Report. CHAIRMAN'S ANNUAL REPORT 1970/71 1970/71 Committee-Office Bearers: Chairman - J. N. Saunders Vice Chairman - G. Y. Nisbet Immediate Past Chairman- N. A. Honnet. Due to the sudden retirement of Mr J. N. Saunders, the committee, at a meeting on the 3rd February, 1971 elected Mr G. Y. Nisbet as Chairman with Mr J. M. Meyer as Vice Chairman. After the transfer of Mr Nisbet to C.D.M., the committee, as a meeting on the 12th May, 1971, decided that Mr Meyer hold the Chair in an acting capacity for the remainder of the year. Committee members: Messrs C. J. Isaac, J. G. Kirchener, L. O. W. Leimer, R. S. Pearson, I. G. Thomas and A. von Holdt. Transfers of several office bearers and committee members resulted in Messrs J. M. Meyer, D. N. Smith and G. C. J. Young being co-opted onto the committee.

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020

By G. R. Baiden

Introduction The introduction of teleremote systems to underground mining can provide a significant improvement in the performance of a mine when compared with conventional mining techniques. This paper presents the concepts of teleremote mining in a case study showing how the systems work and the competitive advantage autonomation of mining techniques will provide for underground metal mining operations into the future. This paper is divided into two sections: the Mining Automation Program and What is next? On January 1st 1996 Inco Limited, Tamrock Oy, DYNO Explosives Group and CANMET formed a consortium for the development of teleremote mining equipment called the ‘Mining Automation Program’ or MAP. This program included a five-year research and development agreement that combines the talents of the above organizations to create mining equipment and systems for autonomating mining. The projects are based on the communication system currently sold and marketed by Automated Mining Systems Limited. The main components of the program investigated the development of a positioning and navigation module, autonomated systems using teleremote techniques for development and stoping, and software systems to support the use of this equipment. The program included the establishment of a test mine, at Inco’s 175 Orebody near Copper Cliff North Mine. This facility was unique allowing collaboration of companies and research organizations inthe design and testing of techniques and equipment used to apply autonomation to mining. Since the inception of the project other research alliances have been added to enhance the program. These include the application of ground support (Meyco/ Master Builders), muck pile recognition, the broadening of telecommunications links (PRECARN Associates Inc.-MALTA project) and the collection and processing of drilling core through the automated diamond drilling project (J.K.S. Boyles). MAP began as an idea a number of years ago with the fundamental question ‘Can an ore-body be profitably mined through autonomation?’ The concept was to design mining equipment and systems that would allow the teleremote operation of a mine. Automation was only one componentof this much larger teleremote mining issue. To start with, it was essential to prove or disprove the feasibility of this concept. The fundamental requirements are: • Telecommunications • Positioning • Navigation • Equipment • Software • Electronics • Mining Engineering • Organization. Each of these had to be considered. Technically, the feasibility of the project hinged on the successful development of a high capacity communication network, an accurate underground positioning system, a navigation system and finally the electronics and software that could integrate these. Mining equipment that could perform all the mining functions was the next requirement, along with explosive supplies that could be delivered to the holes teleremotely. Whatever the systems developed, they must be able to work in both bulk and selective mining situations and in varying conditions within a mine. Finally, the organizational issues of a change from our current method of operation to teleremote mining had to be understood. After five years of research and development the answer to the question ‘Can an orebody be profitably mined using autonomation techniques?’ is YES! There are still hurdles to overcome, however, the basic premise has been proven. The development and production of underground tunnels and stopes has been done. There have been interesting outcomes in terms of reduced effort to accomplish mining and the total time to mine. Definitions •Automationis the process by which a machine or system is run continuously including the ability for the system to self-correct. •Autonomationis the same as automation except that the process does not self-correct. •Teleremote operation is the operation of mining equipment over a network from any location out of line-of-sight of the machine. •Equipment Automationis the addition of technology to a machine that allows for unmanned operation of a machine and thus enhances the productivity of the operator. For example, a guidance system that allows a load-haul-dump to drive by itself, thus freeing the operator for other tasks. •Teleremote mining describes a mine process that combines the use of teleremote operation (potentially with some automation), positioning and process engineering, monitoring and control. •Tamrock DataSoloTMis a computerized drilling rig as shown in Figure 1. •Tamrock DataMini™ is a computerized development drill rig used for drifting and construction tunneling as shown in Figure 2.•Tamrock Toro 450™ is a LHD (Figure 3).

Sep 1, 2001

By M. Z. Naghadehi, F. F. Nasategay, J. Sattarvand, R. Battulwar, E. E. Gohari

After the recent increase in catastrophic failures of tailings dams such as the Burmadinho, Brazil failure in 2019, the mining industry has actively engaged in the stabilisation of tailings dams. Most of the tailings storage facility (TSF) guidelines suggest a laborious action that can be facilitated through imaging by unmanned aerial vehicles (UAVs). Although UAVs are not unknown to most mining operations, automated rill detection through aerial image processing is a new concept. This study utilises images from sites in the U.S. and employs semantic segmentation with a UNet architecture to detect location and size of these rills. The developed model can be used as a tool for monitoring surface erosion of TSFs.

Sep 1, 2021

By K. Cole, D. Mesa, P. R. Brito-Parada, M. R. van Heerden

Turbulence in stirred tank flotation vessels determines the bulk transport of particles and has an important role in particle-bubble collisions necessary for attachment. Positron emission particle tracking (PEPT) produces quantitative measurements of the kinematic motion of different particle classes inside flotation vessels. This paper presents flow profiles of the vessel, residence time distributions, flow profiles through the mesh and macroturbulent kinetic energy distributions as experienced by valuable (hydrophobic) mineral particles in a laboratory scale flotation vessel. The results highlight the impact of the rotor-stator design and a retrofit mesh modification at the upper part of the vessel which improve recovery by decreasing turbulence in the quiescent zone and at the interface. Keywords: Flotation machines, turbulence, PEPT

Jan 1, 2020

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By N. Duda, P. Śliwiński, P. Stefaniak, B. Jachnik

Ventilation and air-conditioning are some of the most energy-consuming processes in deep underground mining. Additionally, the energy consumption of these processes systematically increases along with the expansion of the mine. Therefore, proper energy efficiency assessment and consumption forecasts of these systems are particularly important in modern mines for ongoing tracking and planning of the likely costs. In the article, a short-term prediction model for surface air–conditioning stations is described. This model takes into account dependencies that were identified, based on the data from the supervisory control and data acquisition (SCADA) systems. These dependencies between the response value and the external conditions are then incorporated into the model. This way, for example, the ambient temperature or the total number of specific days of the week (with sometimes significantly lower or higher than the weekly average energy consumption levels) are included. Taking into account these dependencies, and e.g. forecasted average monthly temperatures allow us to include the seasonality of energy consumption in the presented model. In the article, a sample energy efficiency analysis of the A/C system based on an example of the KGHM Polish Copper Polkowice-Sieroszowice mine is performed. The results of the solution proposed in the article are then evaluated, and compared to the currently functioning, more basic forecasting methods. However, given the general nature of the dependencies used in the model, similar solutions could be used in other case studies.

Sep 1, 2021

By G. de Tomi, G. C. Teodoro, E. Rodovalho, T. M. El Hajj, J. A. S. Tenório

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore bodies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Sep 9, 2024

By M. Rudolph, A. van Hall, G. Öktem, S. G. Özkan, A. Hassanzadeh

Despite the four-decade study on ultrasound’s (US) impact on mineral’s floatabilities, there is still not clarity regarding its role in mineral surface wettability. For this purpose, the present investigation endeavours ……the hydrophobicity and floatability characteristics of a chalcopyrite-pyrite-quartz (Cp- Py-Qtz) system in the presence and absence of an ultrasonic pre-treatment. The ultrasonic process was carried out by a sonopuls at a constant frequency of 20 kHz with an adjustable power level from 30 to 200 W. Initially, the impact of sonication time (15, 30, 45, 60 and 90 s as well as 10, 20 and 30 min) and power magnitude (30, 60, 90, 120 and 180 W) were evaluated while the dissolved oxygen, temperature, conductivity and pH were also monitored. Collector-less micro-flotation tests were carried out on the non-pre-treated and the US pre-treated samples at 60 W and 15 s. The samples’ hydrophobicities were determined by the drop shape analysis approach. The dissolved-oxygen level was varied using a mini bench pressurised water reactor to study the effect of O2(aq) concentration on the chalcopyrite and pyrite wettability characteristics. The results showed that the minerals’ hydrophilicities were relatively more sensitive to the sonication’s time than its power that resulted in reducing all three minerals’ hydrophobicities. In addition, it was found that the dissolved-oxygen content and creation of sub-micron sized bubbles led to an improvement on chalcopyrite and pyrite hydrophobicities. Finally, we proved that the Cp’s floatability increased and Qtz’s recovery reduced while being subjected to the ultrasonic irradiation (15 s at 60 W); however, Py’s recovery remained constant. This conclusion confirmed the possibility of a selective separation in ultrasound-assisted copper ore flotation. We recommend that further advanced investigations be conducted, using an X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) to thoroughly understand the surface modifications induced by the ultrasonication

Jan 1, 2020

By B. Oladipo, E. Govender-Opitz, T. V. Ojumu

Bioleaching, one of the several important processes of biohydrometallurgy is an accepted technique for the extraction of desired metals from sulphide ores. Although the mechanism is well understood, the slow metal extraction rate due to passivating layer and ferric ion precipitation, especially in a typical chalcopyrite leaching, impact negatively on the overall efficiency of the process. Iron precipitates are common in many biohydrometallurgical operations and these precipitates represent the exit route for undesired iron, alkali ions or sulphate ion from the processing circuit. While there have been reports on approaches to slow the formation of these precipitates by manipulation of various operating conditions such as pH, redox potential and temperature, the precipitates become highly significant over the long term in the continuous operation of bioleaching and may render heap impermeable. Although there is evidence supporting the nature of the passivation to be precipitates of iron, their scavenging mode of reducing extraction efficiency is still not well understood. This paper thus discusses iron precipitation in biohydrometallurgical processes, including its formation and significance on bioleach processes. The paper also details the associated passivating species identified with heap bioleaching of sulphide minerals and provides some insight into sorption mechanism that limits metal recovery in a typical bioleach operation. Keywords: Iron precipitation, bioleaching, chalcopyrite, passivation, jarosite, metal sorption

Jan 1, 2020

By S. T. L. Harrison, A. Kotsiopoulos, M. D. Maluleke, E. Govender-Opitz

In the extraction of base metals from printed circuit boards (PCBs) using bioleaching, the accumulation of metal ion stress in solution has been shown to inhibit the microbial regeneration of ferric iron. This poses a challenge for the development of this technology for e-waste treatment. The paper explores the application of a microbial immobilisation system in a two-stage bioleaching system consisting of a chemical leaching reactor in series with a microbial ferric iron regenerating reactor to mitigate microbial inhibition and to enhance base metal extraction. A mixed microbial culture dominated by L. ferriphilum, L. ferrooxidans and At. Caldus was maintained over a period of two months in the presence of polyurethane foam which acted as the biomass support particle. Microbial metabolic activity of immobilised cells and their tolerance to inhibitory Cu ions was investigated. Results showed that immobilised microbial cells maintained higher ferrous iron oxidation activity compared to planktonic cells in the presence of increasing Cu2+ concentrations up to 6 g/L. This presents an opportunity for microbial immobilised systems to be adopted in two-stage bioleaching system. Keywords: Bioleaching, microbial immobilisation systems, microbial inhibition and ferrous iron oxidation

Jan 1, 2020