Search Documents

By S. H. Ash

For several years considerable activity has been devoted to economic and social factors affecting California metal-mining operations as they relate to accidents and their cost. The reason for this intense interest is that accidents cost this industry annually over $1100,000 in industrial insurance premiums for mines insured by insurance carriers only; during 1924-32, inclusive, they amounted to $3,616,9115. There are several reasons for this high cost, the most important of w rich are the consistently .high frequency and severity rates of injuries occurring in the industry. Coordination of effort, appreciation of a mutual problem, and widespread education are essential if accidents and their cost are to be reduced.

Jan 1, 1935

By L. R. Herrmann

The research described in this report is the first phase of a comprehensive program for the development of a characterization for the structural properties of rock masses. The mathematical expression of the characterization is especial' tailored for use in conjunction with modern structural analysis procedures. The objective of the first phase of the project is to determine the feasibility of representing the structural properties of rock masses in terms of the analysis of an appropriate "representative volume" the results of this investigation are described in detail in the body of the report. The current state-of-the-art concerning the understanding and description of the fundamental mechanisms of rock behavior are determined from a survey of existing literature. The development of a representative volume that captures the most important of these mechanisms is described, In order not to unduly obscure the fundamental aspects of this development, the mathematical analysis of the representative volume is limited to plane strain conditions. A subroutine for the numerical evaluation of the proposed model (i.e., the analysis of the representative volume) is presented. The steps necessary for the incorporation of the subroutine directly into existing two-dimensional finite element structural analysis programs are described. Comparisons between the predictions of the proposed characterization and published results of simple laboratory tests are presented and discussed. Finally recommendations are given concerning suggested improvements of the model and the extension of it to the general three-dimensional case.

Jan 1, 1974

Arsenic.--Inorganic arsenic has been added to the Environmental Protection Agency's list of hazardous air pollutants because of a high probability it can cause cancer. EPA estimates that inorganic arsenic emissions into ambient air total more than 6,000 tons per year, with about 65;L of this coming from the operations of copper, lead, and zinc smelters. Asbestos Detection.--In June 14, the President signed S. 1658 providing $172.5 million to detect and remove asbestos hazards in schools. Asbestos Use Must be Reported.--All firms using asbestos in the manufacture of some 30 categories of products must describe in detail how they use the mineral to the Consumer Product Safety Commission, for all manufactures since January 1, 1977.

Jan 1, 1980

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining. In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office-workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections: 1. General injury experience: Tables I-5-Data on injuries, injury-frequency and severity rates and related employment data, work location, and degree of injury.

Jan 1, 1963

By G. D. Bakulev

Economic Importance of Gasification of Fuel and Brief Outline of Development of Underground Gasification of Coal in the U.S.S.R. The underground gasification of fuel offers a number of economic and social advantages, principally the following: 1. Full automation of labor-consuming coal-mining processes, which resist complex mechanization and automation, particularly shaft mining. 2. Elimination of hard, dangerous, and often unhealthful mining work. 3. Creation of hygienic conditions for personnel employed in gas production, as well as for those in boiler rooms using the gas. 4. Possibility of automation of complex production processes of thermal-electric powerplants using underground gas with economic installations for steam production. 5. Economic operation of thermal-electric powerplants constructed in the areas of underground-gas production. 6. Release of railroads from the burden of transporting fuel. 7. Extension of the power base of some areas in need of fuel and of the economy as a whole due to use of fuel deposits not amenable to normal mining practices. 8. Reduction of capital investments per unit of energy produced in the form of fuel. 9. Substantial increase in general labor productivity. 10. Possibility of substantial reduction in the cost of fuel produced and of electric power produced from underground gas.

Jan 1, 1962

By Glan Dale Coe, Will H. Coghill

"INTRODUCTION Characteristics of the mineral products that are to be contrasted herein are net energy consumed in grinding to a definite top limiting size and size distribution of the ground products. Through contrasts of these grinding characteristics this paper to differences in related mineral products and in unlike products. For,example, in anticipation of the data to follow, although Joplin chert and Babeitt taconits are running mates in defying the best crushing machinery, taconite is one of the more docile and Joplin chert one of the most refractory mineral products ordinarily fed to a grinding Routine grinding tests on a great variety of ores and tabulation of the findings have been covered amply by Lennox 4/ and by Maxon 5/ and associates. In contrast to that work, the present paper is a record of random tests made over a long period, and each answered an urgent question at the moment. The work was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama. The pressure of war work prevented an organized investigation."

Apr 1, 1943

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the utilization of municipal solid waste. One of the primary objectives is the recycling of the magnetic fraction of municipal solid waste (raw refuse). This is consistent with one of the Bureau's goals, which is to minimize the requirements for mineral commodities by maximizing metals recovery from secondary domestic resources, In this investigation, cupola trials were made using combinations of refuse scrap with shredded automobile scrap under basic and acid slag practices. Furnace operating information and the behavior of alloying and tramp elements was obtained. The research showed that it is possible to utilize up to 60 percent refuse scrap in the cupola under basic practice and 30 percent under acid practice, Aluminum in refuse scrap, present in bimetallic cans, increased the recoveries of silicon and manganese charged to the cupola. Increased use of refuse scrap provided iron of lower sulfur. The alumina resulting from oxidation increased the slag volume. The aluminum and tin contents of the iron increased with increasing levels of refuse scrap in the charge. Lead was not a problem with respect to contamination of the iron. In basic practice, operation of the cupola was satisfactory since all slags were adequately fluid. In acid practice, operation became troublesome above the 45-percent level. Under both practices, the cupola iron melting rate decreased. Particulates in scrubber water and stack condensate samples contained lead, zinc, and tin, and the dust load increased. The tensile and transverse strengths of the iron produced under both practices are reported.

Jan 1, 1980

By James E. Norman

[The flotation of mica is mentioned frequently in the literature, but must of the references have dealt with the recovery of mica by the old anionic collectors. The first use of the new cationic reagents indicated their superiority- as collectors in the flotation and a. agglomerate tabling of micas, feldspars, quartz, clay, and other acidic mineral, but the separation n of these minerals from each other necessitated study of the flotation of each mineral.]

Jan 1, 1941

By James E. Norman

[The flotation of mica is mentioned frequently in the literature, but most of the references have dealt with the recovery of mica by the old anionic collectors. The first use of the new cationic reagents indicated their superiority as collectors in the flotation and agglomerate tabling of micas, feldspars, guartz, clay, and other acidic minerals, but the separation of these minerals from each other necessitated of the study of the flotation of each mineral.]

Jan 1, 1941

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

By John C. Machisak

INJURY experience and employment data at all metal mines in the United States and Alaska are presented in this Information Circular for the calendar year 1958. This publication covers the metal mining industries, and contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. These operations report injury and employment information annually to the Bureau of Mines on a voluntary basis. The Bureau is authorized to make requests for such data, and the information submitted contributes immeasurably to the promotion of safety in the metal mining industry. Every effort has been made to make the annual canvass as complete as possible. This publication contains, along with production and development workers, the office employees at the mine location. The metal mines identified in this publication are classified according to the mineral ores mined; that is, copper, iron, lead-zinc, gold-silver lode, gold placer, and miscellaneous metals.

Jan 1, 1962

By A. C. Smith

The U.S. Bureau of Mines constructed a large-scaJe facility to study the self-heating of a large coal mass under conditions that simulate a gob area of a mine. The insulated coal chamber can hold up to 13 short tons (st) of coal and is provided with a forced ventilation system and computer-controlled temperature and gas measurement systems to monitor the heat and mass transfer phenomena that occur in the coalbed. Three experiments were completed with high-volatile C bituminous coals that exhibited high spontaneous combustion potentials in laboratory-scale tests. In the first two tests, a sustained heating was not achieved. In the third test, temperatures throughout the coalbed increased steadily from the start, with thermal runaway occurring near the center of the coalbed after 23 days. The thermal reaction wne then moved toward the front of the coalbed. The results of these tests showed that the self-heating of a large coal mass depends not just on the reactivity of the coal, but also on the particle size of the coal, the freshness of the coal surfaces, the heat-of-wetting effect, and the availability of O2 at optimum ventilation rates.

Jan 1, 1991

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel- economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the 3 reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

More than 400 academic, Government, and industry representatives attended the third symposium on ash utilization and technology held in Pittsburgh, Pa., March 13-14, 1973. Sponsored by the American Public Power Association, Edison Electric Institute, National Coal Association, National Ash Association, and Bureau of Mines, the symposium Featured 26 formal presentations by leading experts from Europe and the United States on all major phases of ash production, utilization, and research. Abstracts of all the papers are grouped right after this introduction, and the full symposium proceedings follow. Sponsoring organizations and their chief representatives were the National Coal Association, James R. Garvey, Bituminous Coal Research, Inc.; Edison Electric Institute, C. E. Brackett, Southern Electric Generating Co.; American Public Power Association, Herbert Blinder, Columbus (Ohio) Electricity Division; National Ash Association, Inc., James N. Covey, Rochester Gas and Electric Corp.; and the United States Department of the Interior, Bureau of Mines, William L. Crentz.

Jan 1, 1974

By Donald J. Ninteman

This Bureau of Mines publication is a literature study of the problem of spontaneous oxidation and combustion of sulfides in underground mines. It summarizes the present-day hazards, process mechanisms, and prevention and control techniques of this growing problem in underground mines. The iron sulfides generally have the greatest tendency to oxidize, particularly pyrrhotite. The presence of moisture and oxygen is essential for the oxidation reaction. Highly fractured sulfides, when found with timber or combustible refuse in slowly circulating air, pose the most serious fire hazard. Quenching with water is effective in quickly dealing with local hot spots, but ventilation at high flaw rates is the most effective and economical means for long-term prevention and control.

Jan 1, 1978