Search Documents

By David K. Denton

There are no active mines in the Mt. Eddy RARE II area. Chromite, gold, and stone prospects were examined. The RARE II area contains no identified mineral resources; however, a sample of a 260 ton occurrence contained 38.1 percent chromium oxide (Cr203) at the Ratero Prospect (fig. 1, no. 3), which has low potential for chromium resources. The Johnson Mine (fig. 1, no. 6) produced a small unrecorded amount of chromite during World War IT, but only a low potential exists for chromium resources. A low potential exists for gold resources at the Half Century Prospect (fig. 1, no. 2). At a borrow pit northwest of the study area (fig. 1, no. 1), sheared serpentinite is quarried for road metal; similar rock occurs in the RARE II area, but better material is more readily available elsewhere. Sand and gravel occurrences are too inaccessible and distant from markets to be considered resources. Mineral fuels and geothermal resources were not evaluated during this Bureau of Mines study. There currently are three unpatented lode mining claims in the study area. INTRODUCTION The Mt. Eddy RARE II area is 7 air-mi west of Mt. Shasta City, California, and straddles the Siskiyou-Trinity county line. The roadless area includes 7,200 acres of rugged, glacially carved, ridges and drainages which comprise Mt. Eddy. Elevations vary from 6,000 ft along the North Fork Sacramento River to 9,025 ft at the summit of Mt. Eddy. The area is covered with conifer forest below 8,000 ft elevation.

Jan 1, 1983

By Jennifer Riefenberg

The U.S. Bureau of Mines has long recognized the hazards associated with rock burst activity in underground mines. Concern over lost lives and resources prompted this study to further characterize rock burst occurrence as related to microseismicity and mining. A period of over 1,079 days of mining with 101 bursts, where microseismicity rates and blasting were recorded, was used in this study. Statistical analyses investigated relationships between (1) rock burst occurrence versus blasting, (2) rock burst size versus damage, (3) rock burst occurrence versus average micro seismicity rates, and (4) rock burst occurrence versus local mine geometry. Statistical analyses showed that 91% of all rock bursts occur with blasting while only 3% of all rock bursts occur, apparently, independent of blasting. Additionally, the long-term average daily micro seismicity rates appear to dictate when blasting will trigger rock bursts. Time series analysis on the daily microseismicity resulted in model equations that may be used to forecast the daily microseismic activity.

Jan 1, 2010

By R. O. Pynnonen

This publication is an analysis of reports to the Bureau of Mines of 44 fatal accidents that occurred during the operation of rubber-tired, front-end loaders in the mineral industry. The causes of the accidents, the nature of the work being performed, and recommendations for preventing similar accidents are included.

Jan 1, 1967

Lower workers' dust exposures during bag stacking while ergonomically improving the bag stacking process. Approach Install a new pallet loading dust control system which uses a push-pull ventilation technique along with a hydraulic lift table to control the pallet loading height throughout the entire loading cycle. How It Works A low-volume, high-velocity blower system operating at approximately at 120 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-inch air jets (approximately 1,200-ft/min velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they en-train dust generated during bag stacking. The dust laden air is then captured by the exhaust ventilation system which draws approximately 2,500 cfm through an exhaust hood on the opposite side of the pallet.

Jan 1, 1989

By Maria I. De Rosa

The major fire and fire injury findings for all metal/nonmetal mining categories for 1990-2001 are shown in tables 64-65. Table 66, partly illustrated in figure 22, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays for all metal/nonmetal mining categories by time period. For all metal/nonmetal operations (including stone and sand and gravel), a total of 518 fires occurred during 1990-2001; 296 of those fires caused 308 injuries and 4 fatalities (Ewhr = 4,012 x 106 hr, In = 0.015, LWD = 36,204). Thirty fires and 26 injuries involved contractors. The greatest number of fires and fire injuries occurred at surface operations; the highest risk rate values were also calculated for surface operations. The number of fires increased during the first four 2-year time periods (1990-1991, 1992-1993, 1994-1995, and 1996-1997), then decreased during the last two periods (1998-1999 and 2000-2001). The number of injuries showed a decrease throughout the periods, accompanied by an increase in employees' working hours. Twenty-five firefighting interventions by mine rescue teams in underground mines and at least 30 interventions at surface operations were required to combat these fires. However, 45 fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. Ninety-seven fires were detected late, and 30 fires were undetected. The ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flame (169 fires or 33% with 137 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (89 fires or 17% with 46 injuries and 3 fatalities), heat source/explosion and flammable liquids/ gas/refueling fuel on hot surfaces (98 fires or 19% with 73 injuries), electrical short/arcing (51 fires or 10% with 16 injuries), and spontaneous combustion/hot material (46 fires or 9% with 17 injuries). The flame cutting/welding spark/slag/flame source caused fires usually involving welders' clothing or oxyfuel/grease and other materials (including chute and dust collector liners, flammable liquids, belt material, crusher, hopper and shaker deck materials, washer plants, equipment mechanical components, stampler breaker, hydraulic fluid, rubber tires and hoses, gear boxes, bin feeder, dump rope cables, screen liner and screen panel, kiln and shaft material, pipelines, liquor pumps, wood pallets, electrical junction boxes, handrails, grease, refuse, shop and wood). The spontaneous combustion/hot material and electrical fires were usually detected late due to lack of combustion gas/smoke detection systems. At least 55 of the 89 mobile equipment hydraulic fluid/fuel fires became large fires (requiring 12 mine rescue team interventions in underground

Jan 1, 2004

By C. E. Wethered

This paper describing the mining methods employed by the Federal Mining and Smelting Co., operating the Morning mine at Mullan, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The daily tonnage produced at the Morning mine, including that mined by leasers, is 1,100 tons. Mine run of ore will average 9.1 per cent lead, 5.8 per cent zinc, and 4.4 ounces silver per ton. A stull set and fill method of mining is employed.

Jan 1, 1930

By Gary R. Gavan

This report presents the documentation and User's Manual for a data retrieval and report generation computer program. The program operates on a data base containing over 19,000 pieces of coal mine equipment in use in 1976.

Jan 1, 1979

By G. L. Neumann

In October 1949 the College Park Branch of the Mining Division instituted a survey of the New England pegmatites. Many of the New England pegmatite deposits were superficially examined, and the Bumpus quarry in Albany, Oxford County, Maine (see fig. 1), was selected for a diamond-drill exploratory-development project to supply information for developing more economical mining methods and no increasing production of beryl and other scarce minerals associated with pegmatitic intrusives. The Bumpus quarry has been mined intermittently by three operators since it was opened in 1927. At the time of drilling, the vein or dike (see figs. 2 and 3) had been mined to a depth of 60 feet for a strike length of 280 feet. The dike averages 40 feet in thickness and dips 50 degrees southeast. The Bureau of Mines drilled seven diamond-drill holes between September 27 and November 27, 1950. These holes showed that the dike persists for at least 350 feet to the east and probably 200 foot to the west of the present excavation. The drilling also indicated that the dip, as exposed at the surface, continued unchanged at 500 to a depth of at least 50 foot below the pit. The dike was not delineated, although it fingered out as pegmatite interbanded with Granite, diorite, and gneiss in diamond-drill hole B-4, approximately 250 feet west of the pit. Further drilling will be necessary to find the extent of this pegmatite dike and to determine the safest and most economic mining system.

Jan 1, 1952

By O. M. Bishop

The Douglas fluorite property is in the Empire district of eastern Pope County, Ill., which lies near the west boundary of the productive Southern Illinois fluorspar field in Hardin and Pope Countios. Production from mines on the Douglas property accounts for about one-half of the 72,000 tons of fluorspar with which the Empire district is credited. This output was from the Sycamore, Pierce, Slapout, and Empire veins, which are normal fissure veins of little displacement along which there has been local wall-rock replacement by fluorite.

Jan 1, 1949

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

By L. L. Oden

The Bureau of Mines is conducting research to develop methanation catalysts for converting synthesis gas derived from coal to synthetic natural gas. This report describes a method to prepare supported Raney nickel coatings by dipping screen-covered nickel sheet in molten aluminum-nickel alloy. Coatings were formed at 1,050° C that were comparable in thickness, composition, microstructure, and catalytic properties to flame-sprayed commercially pre-pared Raney nickel. A molten salt comprising cryolite-8 wt-pct LiF was employed over the molten metal bath to clean and preheat the substrates, to protect the metal bath from oxidation, and to heattreat the coated specimens. Immediately following heat treatment, specimens were quenched to 700° C in a molten salt bath containing CaC12-34.5 wt-pct NaCl, which also functioned to remove the insoluble occluded fluoride salt.

Jan 1, 1976

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By Laurance L. Oden

The Bureau of Mines conducted corrosion tests of 18 commercial alloys in H3 P04 -phosphate rock or A1,03 slurry, in 10 pct HF, and in 25 pct H2 SiF6 to simulate three environments anticipated in a Bureau process to extract fluoride values from phosphate rock. Small alloy coupons were rotated in duplicate tests at 4.4 to 21 fps in the slurry at 170° C to determine rates of erosion-corrosion. At 4.4 fps the lowest rates, in mils penetration per year (mpy), were measured for Hastelloy C-276 (<20), Hastelloy B (30), and Inconel 625 (150);the rates increased at 21 fps to 55 mpy, 45 mpy, and 1,000 mpy, respectively. The corrosion rate for all alloys exceeded 40 mpy in either the equilibrium vapor or liquid phases of aqueous solutions containing 10 pct HF or 25 pct H2SiF6 at 100° C. Uniform corrosion in 10 pct HF at 50° C was observed only for Inconel 625 (22 mpy), Hastelloy C-276 (43 mpy), and Illium 98 (17 mpy). Inconel 625 (0.75 mpy), Hastelloy C-276 (1.3 mpy), Illium 98 (1.7 mpy), and Incoloy 825 (0.45 mpy) were attacked uniformly in 25 pct H2SiF6 at 50° C.

Jan 1, 1974

By Sidney Katell

Several systems have been proposed for the production of synthetic crude oil from oil shale. An economic analysis of one proposed system is presented in this paper. An oil shale complex to produce 100,000 barrels per calendar day of semirefined crude oil will require a capital investment of $426,216,400. This investment includes mining, retorting, intermediate pipelining, and partial refining. A selling price of $3.74 per barrel of product will be necessary to maintain a discounted cash-flow rate of 12 percent.

Jan 1, 1971

By Robert W. Freedman

Vacutainers are used by the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) for sampling mine air and products of combustion. Tests were conducted on both 10-ml and 30-ml sizes to study shelf life stability during storage, pretreatment of stoppers, and handling of a wider range of compounds. A chamber was constructed to provide convenient, efficient evacuation of the Vacutainers shortly prior to use. Fixed gases and C1 ?C5 hydrocarbons could be stored for 1 week or more after sampling. Where decreases occurred (C02 and C3-C5 hydrocarbons), they were predictable as a function of storage time. An unexplained phenomenon, slow accumulation of CO in evacuated Vacutainers, occurred after a few weeks of storage. The levels were low and time dependent. Attempts to eliminate this behavior by pretreating the stoppers were unsuccessful.

Jan 1, 1976

By Jerry E. Olson

In 1985 the U.S. Bureau of Mines conducted a mineral survey of 68,458 acres of the Clan Alpine Mountains Wilderness Study Area (NV-030-102) which covers 196,128 acres in Churchill County, NV. Most of the area studied is underlain by Tertiary volcanic rocks. In the northeast corner of the study area, an upthrown block of Triassic sedimentary rocks partially extends into the area. The study area is probably part of a large eroded caldera. No major mines or active claims are within the study area. Field investigations included examination of workings in Starr Canyon, historical and recent mining activity near the mouth of Florence Canyon, other mining claims, and anomalous zones delineated by data from Great Basin GEM Joint Venture studies. No mineral resources were identified, but sample results indicate one significant mineralized zone situated along a northwest trend between the head of Starr Canyon and the head of Cherry Creek may contain precious metal resources. Further investigation of this zone is warranted.

Jan 1, 1987

By John M. Gomes

The Bureau of Mines investigated two techniques for removing CaO from scheelite (CaW04) prior to electrolysis. In the first technique, a crude tungstic oxide (WO3) containing 0.15-percent lime (CaO) was prepared by digesting scheelite concentrates in hot hydrochloric acid. This oxide was used as cell feed to produce tungsten of 99.9-percent purity. The second technique used a high-temperature, two-phase separation, resulting in extraction of 99 percent of the WO3 in the halide-tungstate phase, while 90 percent of the CaO was retained in the silicate phase. Tungsten of 99.9-percent purity was deposited from the halide-tungstate melt after B203 and NaPO3 were added to form an electrolyte. The two methods were compared with a previously developed technique of depositing tungsten from scheelite concentrate fed directly to the electrolytic cell.

Jan 1, 1971

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

By Fred D. Wright

A drill unit designed by Bureau of Mines engineers for testing various types of rotary bits has been in use since April 1950 at the experimental oil-shale mine near Rifle, Colo. The unit has a hydraulic drill and feed system, which provides the wide range of operating conditions necessary for adequate testing of drill bits and for obtaining data needed for the design of production scale equipment. Through the use of this unit, it has been proved that rotary drilling of vertical holes for mining the benches of the oil-shale mine is much cheaper than percussion drilling, and it is believed that in the near future the rotary drilling of horizontal blast holes in the top heading of the mine will prove equally economical.

Jan 1, 1952