Search Documents

By J. Vance Batty

Two methods were devised and evaluated for quantitatively measuring the amount of oleic acid on flotation products and in flotation waters. One method involved use of an organic solvent to remove carbon-l4-tagged oleic acid from mineral surfaces and flotation water phases with subsequent radio-metric analysis of the extracts. Studies showed this method to be slow and subject to large variations in accuracy and reproducibility. In the second procedure, tagged oleic acid was measured directly on the surfaces of dried mineral products. Oleic acid in the water phase was determined by adsorbing it on fine mineral, drying, and radiometric counting. Quantitative analysis of oleic acid on flotation products from bench-scale flotation tests with synthetic mixtures of ore minerals and quartz and with natural ores showed this method to be fast, accurate, and reproducible.

Jan 1, 1968

By D. A. Wilson

A laboratory method for processing lead battery scrap has been developed that eliminates virtually all of the S02 emission that normally is produced when a reverberatory or blast furnace is used. The method employs a hydrometallurgical step to convert the PbS04 to PbO and CaS04 by mixing the battery scrap with a slurry of Ca(OH)2. The reaction is exothermic and goes to completion in 2 to 5 minutes at room temperature. The dried product is mixed with a KC1-NaC1 flux and carbon and reduced at 6500 C. A minimum charge ratio of 3 parts of carbon to 100 parts of battery scrap is required for reduction. The process produces lead reductions and recoveries as high as 97.0 and 94.9 percent, respectively. The KCI-NaCl flux is recovered using a standard counter-current water leach followed by evaporation.

Jan 1, 1976

By W. R. Hardwick

Nuclear explosive fracturing has been suggested as a method to make hard rock amenable to extraction by a modified block-caving method. To evaluate this possibility, conventional and nuclear blasting practices are discussed, underground mining methods for large deposits and their costs are described, and the cost of fracturing ore with a nuclear explosive and subsequent mining by a modified caving system is estimated and compared with both open-stope and block-caving mining costs. While the direct cost of fracturing the ore in hard rock with a nuclear explosive is less than with conventional explosives, additional costs imposed by the use of nuclear explosives may make their use unattractive for deep mining.

Jan 1, 1970

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By C. W. Owings

Available literature published or abstracted in 1953 and 1954 relating to dust prevention and suppression has been summarized and reviewed in this report, and un-published information also is included to outline current practice for those interested in dust control in and around mines, tunnels, and quarries. More and more companies are realizing the value of controlling dust by incorporating suitable methods and devices in the planning stage. In preparation and crushing plants preliminary tests have been made of the fine materials to determine the best type of dust-control equipment to use, and the details of the quantities of air, the number of sprays, the dust-allaying fluids, and the location of hoods or enclosures have been determined in advance. Such planning has paid for itself in more effective control. Similar planning in a tunnel resulted in healthful conditions and low dust concentrations.

Jan 1, 1956

By D. Harrington

Misuse of explosives and heedless disregard of well-known safety rules covering the use of commercial explosives cause many avoidable accidents resulting in the death or maiming of men who can ill be spared by already undermanned industry at present, and who cannot be spared by their families at any tire. Blasting accidents, when not fatal, are usually serious; the past and present needless loss of life and maiming of men from this cause are appalling and types of waste that can and should be virtually eliminated. Dead, crippled, and maimed men are distinct losses to society as well as to industry, and compensation payments for such accidents represent only a portion of the financial loss, because the value of their lost potential production can only be surmised. By their very nature, explosives are dangerous to handle, otherwise they would not perform the services for which they are used; all men on a blasting crew are subjected to the results of the carelessness of any one member, and in many instances the misuse of explosives by one person has killed scores of fellow workers. Inexperienced men should be assigned to blasting operations only under the close supervision of men well-experienced in the work and familiar with its inherent hazards. Men should be selected for blasting crews that are known to be careful, willing to follow instructions, cool-headed, and unlikely to become excited in an emergency; they should be instructed in the safe handling of explosives in accordance with the safety rules established by the explosives -manufacturing companies or the safety codes of the various industrial organizations. Unfortunately, American industry has never adopted a uniform code for the safe handling of explosives; however, many mining companies have made rules that will eliminate most unsafe practices if established safe procedure is followed carefully. The Bureau of Mines has issued numerous pamphlets giving information on the causes of accidents due to explosives in the mining industry and indicating the ways in which a good proportion of those accidents can be avoided.

Jan 1, 1943

By J. T. McCartney

"INTRODUCTION The surface areas of the finest fractions of a pulverized material are disproportionately larger than their weights. For instance, Pesrott and Kinney 3/ showed that, in a sample of minus 200-mesh coal, particles that are about 2 microns in diameter represent 15 percent of the entire surface area but only 1.5 percent of the total weight. Because the sur- face area is the dominating factor in the behavior of finely divided materials in many practical processes, the role of the finest particles is of great importance. The oxidation and combustion of pulverized coal, both in the dry form and in suspension in oils, and the hydrogenation to fluid hydrocarbons of mixtures of pulverized coal and heavy oil are reactions in which the surface area of the coal particles has considerable influence. This investigation of the size distribution of fine coal particles was conducted with the hope that such processes would thereby be better understood. The results should also be of value in the study of the crushing and fracture of coal."

Sep 1, 1945

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,680 samples, representing the products of 130 companies. The samples were collected during December 1953 and January and February 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past ten years is given on page 5.

Jan 1, 1954

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By William A. Beck

Since bauxite mining began in the Irwinton District, Wilkinson County, Ga., in 1912, it has been on a small scale, as most of the deposits of high-grade ore are small. The bauxite has a high silica content, and its use has been largely limited to the chemical industry. Drilling under this project did not disclose any bauxite deposits of commercial value: However, numerous holes penetrated high-alumina clay deposits, but no attempt was made to delimit them, as the project was solely an exploration for bauxite. Bauxite was first discovered near Irwinton in 1907. The district covers virtually all of Wilkinson County and extends into the adjoining counties of Washington, Baldwin, and Twiggs. Mining was begun in 1912 by the Republic Mining & Manufacturing Co. on the Honeycutt, Parker, and Daniel properties, which are 1.5 miles from Wriley on the old Irwinton to Milledgeville Road.

Jan 1, 1949

By E. J. (Kirk) Conway

Thirty-five years ago underground coal mining equipment consisted of simple but rugged machines powered by electric motors and hydraulics. The machines were maintained by maintenance personnel armed with a basic knowledge of hydraulics, electricity, and mechanical design. Over the years the the machine has been transformed into powerful complex mining systems. The maintenance burden has also increased. During this period significant advances have been made in maintainability engineering and system design techniques. Many of these innovations and techniques are applicable to the design of underground mining equipment. The objectives of this project were to; (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess the impact of equipment design for maintenance on productivity and safety, and (3) develop a maintainability design guideline to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. Interviews were also conducted with mine management, safety, and maintenance personnel to identify machine specific design advantages and problems. Visits were also made to six original equipment manufacturers to discuss the design of their equipment for maintenance. Volume I presents an overview of the protocol used and a summary of the findings. Volume II includes the maintainability design guide for underground mobile mining equipment.

Jan 1, 1989

By F. S. LOTT

The number of petroleum refineries in the United States decreased from 399 on January 1, 1947, to 390 on January 1, 1948. On the latter date two additional refineries were under construction , a large one in New Jersey and a small one in Texas . This Crude oil charging capacity, based on complete facilities only , increased in 1947 from 5,569,482 barrels to 6,034,252 barrels per day , owing to material gains reported in all of the larger refining districts . great increase in effective capacity is only in part the result of the completion of major new units for crude-oil processing . Much of it is due to rearrangement and minor additions to existing facilities to permit more efficient and complete utilization . Recent experience has apparently demonstrated that many processing units are capable , with greater emphasis upon maintenance and precise controls , of sustained operations at higher volumes than were indicated in their old rated capacities . This situation doubtless has caused some upward revision in capacity data .

Aug 1, 1948

By A. W. Fahrenwald

Coarse sand flotation, both alone and in conjunction with gravity concentration, is a subject of research at the U. S. Bureau of Mines Field Office, Moscow, Idaho. One of the most important results of this work which is being carried out in cooperation with the University of Idaho, has been the development of a concentration process embodying flotation, classification, and tabling, in the order named. The flow sheet of the process is given in Figure 1. The type of feed desired for this process is coarser than is common in present "all flotation" practice, and is about the size of table feed.

Jan 1, 1929

By John Nagy

Dust explosion data obtained in laboratory studies by the Bureau of Mines are presented for activated carbon, asphalt, charcoal, carbon black, coal, coke, gilsonite, graphite, lignite, miscellaneous carbons, pitch, tunnel dust, and mixtures of these materials with other ingredients. The explosion hazard is shown to increase as the volatile content of the dusts increases.

Jan 1, 1965

By G. B. Gait

This report is the third in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Lackawanna Basin of tile Northern anthracite field is presented. Previous reports IC 8274, published in 1965, and IC 8379, published in 1968, were catalogs of microfilmed maps of mines in the Eastern Middle anthracite field and Wyoming Basin, Northern anthracite field, respectively , Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1970

By Thomas R. Bur

This method of performing general transformations by use of Eulerian angles greatly reduces the time required for the determination of values for the elastic compliance constants (sij), elastic stiffness constants (cij ), Young's modulus, shear modulus, or Poisson's ratio for any orientation the cartesian coordinate system in an anisotropic material.

Jan 1, 1969

By M. D. Carver

This publication describes development by the Bureau of Mines of a quality evaluation procedure for certifying the adequacy of production lots of Kroll process zirconium sponge the Bureau had produced for reactor applications. After the procedure was devised, the next step was to apply it in controlling the quality of one-half million pounds of zirconium sponge com-prising 259 production lots, called blends, originating at the Metallurgy Research Center of the Bureau at Albany, Oreg. The Bureau concluded that the evaluation method developed was adequate and that by this method the zirconium blends having impurity levels or other property values outside specification limits were differentiated and thus were diverted from nuclear energy end uses. The research was performed under contract for the Bureau of Ships, Department of the Navy, and for the Atomic Energy Commission (AEC).

Jan 1, 1960

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By George C. Branner

This study was planned to present salient facts of the California and Nevada sulfur industries and to indicate existing opportunities for increased economic utilization of California and Nevada sulfur resources. Numerous publications on sulfur have been issued by the Federal Bureau of Mines, including Information Circular 6329, Sulfur, by Robert H. Ridgway (1930); annual Minerals Yearbook chapters on Sulfur and Pyrites, by various authors; and a chapter on Sulfur by G. W. Josephson in Bureau of Mines Bulletin 556, Mineral Pacts and Problems (1956). This literature, however, deals primarily with the national and international sulfur situation and does not attempt to analyze the possibilities for increased economic development of sulfur resources by individual States. The present study attempts to analyze these possibilities in California and Nevada and to (1) evaluate factors that have influenced production and consumption in California and Nevada and (2) indicate apparent trends in production, consumption, and prices in these States.

Jan 1, 1959