Search Documents

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By A. H. Beebe

This paper describing the operations of the Cresson mine of the Cresson Consolidated Gold Mining & Milling Co. at Cripple Creek, Colorado, is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. The Cresson has recently been the most, important mine in the Cripple Creed district. During 1932 and 1933 an average of 230 tons of new ore (excluding dump material) that averaged about $10 in gold was shipped daily; 150 to 175 men were employed. Stoping was by the shrinkage method exclusively. The ore was screened washed, and hand-sorted at the surface and shipped to the Golden Cycle mill at Colorado Springs for treatment. A considerable proportion of the production was made by lessees working under the so-called "split-check" system. The authors are indebted to the management of the Cresson Consolidated Gold Mining & Milling Co. for permission to publish this paper.

Jan 1, 1934

By M. K. Quinn, N. P. Reddy, A. W. Khair

"An analysis of coal fragmentation due to the action of a continuous miner is presented. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). The rotary coal cutter provided the versatility of varying the operating and in-situ parameters to provide information on the effects of generating 37 pm (0.0015 in) particles. In these tests, coal blocks with an approximate dimension of 50.8 x 35.6x 20.32 cm (20x 15x 8 in) were first subjected to confining pressures equivalent to in-situ conditions. The blocks were then cut by the rotary cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as (1) penetration of bit into coal, (2) penetration resistance (thrust and cutting pressures), (3) rotating velocity of' cutting head, and (4) acoustic emission activity in the coal block were monitored. During the test, all the cut products were collected for size distribution analysis. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using a camera attached to an optical microscope.The results led to a better understanding of the mechanisms of the fragmentation process during coal cutting and the effect of operating parameters, in-situ conditions and coal type on the size distribution of the cut product:"

Jan 1, 1989

By D. J. Bauer

The Bureau of Mines demonstrated the feasibility of fractionating lanthanide nitrates with a tertiary amine on lanthanum-cerium and thulium-ytterbium pairs. Optimum values were determined for pH, phase concentration, and percent chelation of metal ions in the aqueous phase. Percent extraction is markedly dependent on the concentration of lithium nitrate in the aqueous phase. Selective masking of the heavier element in each extraction system with DTPA or EDTA aqueous-phase chelating agents resulted in lanthanum-cerium separation factors of 8.5 and thulium-ytterbium separation factors of 3.4.

Jan 1, 1966

By Chester L. Arnold, Reinhardt Thiessen, Alexander Lowy

"INTRODUCTION Peat is the accumulated mass of plant materials that remain after partial decay under specific conditions. In the swampy peat bogs dead material which falls on the surface immediately is attacked by fungi and aercbic bacteria. Decay under these conditions is rapid, but of relatively short duration, since the constant addition of new material soon forces the older layers below the water level, in this position, without access to oxygen, the plant constituents are attacked mainly by anaerobic bacteria, and decomposition proceeds slowly. The largest part of peat is contributed by the woody tissues of plants, the chief constituents of which are cellulose and lignin, together with a small proportion of hemicelluloses. During the normal process of biological decay celluloses disappear more rapidly than lignin. The result is a complex substance known as humin, from which the humic acids may be extracted.In 1826, Sprengel 5 found that when decayed plant materials were extracted with alinnli and the resulting black liquid acidified with mineral acid a brown gelatinous precipitate was formed. To this product, which was a brown amorphous powder when dry, he gave the name ""humic acid'. Since that time, chemists have used the name rather loosely to designate products which have been isolated by very diverse means from soils, decayed woods, peat, lignite, and coal. An excellent review of the early work on humic acids was published by Baumann 6 in 1909. This publication aroused the interest of Oden, who then investigated the humic acids. An account of Oden’s work, as a good survey of the literature, is contained in his monograph “Die Huminsauren”. 7"

Nov 1, 1934

By R. E. Morgan, Barkleym J. F.

"INTRODUCTION Wood burned for commercial heat and power usually is waste material from some manufacturing process. The amount of it reaches substantial proportions. It is estimated that over 50 percent of the timber cut for lumber becomes ""waste"" in the process - sawdust, shavings, trimmings, slabs, and bark. Woodworking manufacturing processes also produce much waste. The incentive to use this waste has resulted in much development of wood-burning equipment to produce heat and power. To answer general inquiries received by the Bureau, this publication covering developments along these lines was written. There is included a bibliography of additional information on the subject.COMPOSITION AND BURNING CHARACTERISTICS OF WOODThe approximate composition of moisture-free wood is, in even figures:PercentHydrogen 6Carbon 49Oxygen 44Ash 1Total 100This composition corresponds to about C6H1005. Moisture is essentially always associated with wood. Green wood contains approximately 30 to 50 percent moisture; air-dried or seasoned wood contains 15 to 25 percent and kiln-dried about 8 percent. Exposed to the weather, wood absorbs and gives off moisture depending on weather conditions and water contact.""Dry"" wood ignites relatively quickly and readily gives off volatile matter when heated. Long flames and smoke easily occur during burning. The burning action is substantially retarded, however, by appreciable moisture content; ignition is more difficult. When the moisture content is more than about 70 percent, an auxiliary fuel is required to maintain combustion. One of the main factors in the problem of the satisfactory and smokeless combustion of wood is its moisture content."

Sep 1, 1950

By John E. Trombly

System objectives and design criteria for an in-mine visual personnel paging system are discussed. Display technologies are evaluated and tradeoffs leading to display selection are described. The prototype dispatcher's console, battery/receiver box and visual display assemblies are functionally described. The report includes circuit descriptions, schematics, parts lists and equipment cabinet drawings for the three assemblies. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 1975

By Laurel A. Powers

The Bureau of Mines process for recovering Ni and Co from low-grade domestic laterites uses a reduction roast followed by an ammonia, ammo-nium sulfate leach. This investigation examined the waste streams of the process for their potential environmental impact and focused on the laterite residue produced. The U.S. Environmental Protection Agency's extraction procedure (EP) toxicity tests and column leaching showed that leachable metal concentrations would be low enough so that the residue would not be considered a hazardous waste under present definitions. Under nonacid leaching conditions, about the same amount of metal was extracted from laterites as from their residues, and the leachates were similar to water samples from an undisturbed laterite deposit. Washing tests on the laterite residue showed that ammonia and ammonium sulfate concentrations were reduced according to equilibrium stage calculations, resulting in residues that would be acceptable for revegetation. With water washing only, the residue would not be considered a hazardous waste even though significant amounts of Ni and Co were absorbed from entrained leach solution onto the residue. Washing first with fresh leach solution and then with water prevented this absorption and thus improved the overall metal recovery.

Jan 1, 1983

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1954 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline. Data also are given for 30 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers I 1954 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 15 producers of aviation jet fuels are represented.

Jan 1, 1955

By Sathit Tandanand

This Bureau of Mines report describes the method of obtaining a strength index for rock drillability, particularly for percussion drills. The original Protodyakonov method has been slightly modified, essentially to eliminate uncertainties in the measurement of the volume of fines, and to avoid conjecture in selecting the representative value as the strength coefficient. A theoretical consideration of the relevant parameters in the method was extended from a comminution theory, and hence the meaningful value was obtained experimentally by plotting the ratio of the number of drops and the volume of fines against the number of drops. The minimum ratio of the number of drops to the volume of fines in the plot was selected as the coefficient of rock strength. The modified method of obtaining the strength coefficient preserves the original Protodyakonov test apparatus and the merit of simplicity of the test procedure. The modified coefficient of rock strength shows its usefulness in predicting penetration rates with greater reliability than other mechanical properties. Consequently, the drillability curves were drawn using the modified coefficient of rock strength as the parameter for penetration rate prediction in the field.

Jan 1, 1975

By H. M. Harris

The Bureau of Mines investigated chlorination of domestic ilmenites in a fluidized coke bed at temperatures of 950° to 1,150° C. Objectives were to develop an effective process for producing TiC14 suitable for TiO2 pigment and to reduce pollution by collecting and treating waste byproduct chlorides. The reactor for these tests was a 10.2-cm-diam quartz tube heated externally by electrical resistance heaters. It contained coke beds of from 35.6 to 82.5 cm in depth that were fluidized by 13 to 25 l/min of chlorine. Ilmenite concentrate powders were introduced at the bottom of the fluid-bed reactor, using the chlorine gas stream as a carrier. Test results showed that greater than 90 pct of the ilmenite reacted at optimum conditions and recovery of TiC14 ranged from 95 to 99 pct of stoichiometric. A temperature-controlled cyclone was used to remove high-boiling-point chlorides such as MnCl2, MgCl2, and FeCl2, and also collected fine unreacted ilmenite and coke dust. Impure TiC14 and FeC13 were separated by collecting the, iron chloride in a condenser con-trolled at 200° C. Titanium tetrachloride vapor was cleaned by passage-through a salt-column filter followed by condensation in water-cooled and refrigerated condensers. Liquid TiC14 was purified further by well-known industrial methods to meet specifications for pigment-grade chloride. Integrated tests were conducted in which chlorine, produced by dechlorination of FeC13 with oxygen, was recycled and used directly in a fluidized-bed chlorinator.

Jan 1, 1976

By Otto Ruhl

"INTRODUCTION With the conclusion of the war and the ensuing readjustment of industry to peacetime conditions, the Bureau of Mines recognized that definite and complete figures on the reserves of zinc and lead ores in the Tri-State District would be needed for an evaluation of the problem of reconversion. In October 1945 its engineers began examination of all the mines and pros¬pects in the Tri-State area and assembling of the basic data for a complete detailed estimate of the reserves of the field. Six to twelve months will be required to complete the report with the personnel available; therefore, it has been deemed advisable to provide as much data as possible for imme¬diate use. Accordingly, a confidential report prepared in January 1944 for the use of and in cooperation with the War Production Board has been brought up to date to form the basis of this preliminary estimate of reserves.The 1944 report has been revised by first subtracting from the reserves then set up for each mill group the amounts mined and milled by those properties for 1944 and 10 months of 1945, with November and December estimated. These production statistics were taken from the monthly reports of the Metal Economics Division of the Bureau of Mines. The remaining reserves were then adjusted by additions of tonnages of new reserves disclosed by developments during the years 1944 and 1945. Such additions were based upon the data furnished by various operators, upon estimates supplied by the Federal Geological Survey District Office at Miami, Okla., and upon estimates of the engineers of the Bureau of Mines Joplin field office.It is apparent from the work so far accomplished in the detailed exami¬nations now under way that the final estimate of reserves will probably be somewhat greater and will differ to a certain degree from these preliminary totals, not only as to the tonnages of ere but also as to grades and distribution by areas. This is due to the fact that all the factors of development, exploration, and geology are being considered in the present examination and report for each individual mine and prospect, whereas the previous reports covered only the immediate development factors surrounding each mill group then in active operation or projected for operation at some early date in accordance with the possible needs for war production."

Aug 1, 1946

By F. E. Cash

Among petroleum refinery employees and officials throughout the United States there has been marked effort to reduce accident frequency and severity. For the interest and benefit of refineries both in Louisiana and in other petroleum-refining States it has been possible to obtain from five refineries, representing 70 per cent of the production of Louisiana, tae accident experience for the past 3 to 6 years. The companies concerned have requested that their names be not used. For tide reason the four plants listed and discussed are designated as refineries A, E, C, and D. The size of the plant as regards largest to smallest number of employees is indicated by the alphabetical order.

Jan 1, 1933

By E. Morrice

The Bureau of Mines investigated methods for beneficiating platinum-palladium ores from the Stillwater Complex, Montana. Results of bench-scale and pilot-scale studies employing froth flotation to recover sulfide concentrates containing platinum-palladium values from a serpentinized ore are presented. Best results in the pilot mill were obtained with a sodium isobutyl xanthate-normal dodecyl mercaptan col-lector combination at a natural pH of 8.2. A rougher concentrate con-taining 1.7 oz/ton Pt and 4.7 oz/ton Pd was prepared. Recoveries of platinum and palladium were 96 pet and 86 pet, respectively. Batch cleaner flotation of rougher concentrates yielded concentrates contain-ing 3.7 oz/ton Pt and 9.8 oz/ton Pd.

Jan 1, 1984

By G. W. Birge, D. E. Wolfson, J. H. Lynch

Fourteen coal samples representing the Flag , Fire Clay , Whitesburg , Amburgy , Upper Elkhorn No. 3 , Upper Elkhorn No. 2 , Upper Elkhorn No. 1 , and Lower Elkhorn beds in Letcher County , Ky . , were carbonized by the Bureau of Mines - American Gas Association ( BM- AGA ) method , and yields of products and physical properties of cokes were determined . The samples tested were high- volatile A bituminous in rank , with dry , mineral - matter- free fixed - carbon contents ranging from 55.3 to 62.2 percent . Five of the samples , as received , were chemically unsuitable for metallurgical use because of excessive ash and/ or sulfur content . Generally , strength indexes of the cokes were low and all of the coals would require blending with higher rank coal to obtain satisfactory blast furnace fuel .

Jan 1, 1964

By Otto Ruhl

The Oronogo-Webb City-Duenweg district is in the northeastern part of the Tri-State zinc and, lead field. Its metal-mining history dates from the early 1850's. For some years prior to 1918 it ranked as the leading producing area of the entire Tri-State field, but by 1920 most of its mines had been abandoned and allowed to fill with water. Its mine operators had-been attracted, to the newly discovered and richer deposits around Picher, Okla. In 1943, the Orenogo Mutual Mining Co. was exploiting the Oronogo Circle deposit in the northern end of the district, and the Federal Mining & Smelting Co. was preparing to mine on its holdings in the southern part near Duenweg. The area between these two operating units ranked as the largest single block of ore reserves under water in the Tri-State field. In 1942, engineers of the Bureau of Mines, in collaboration with the William Stewart Engineering Co. of Joplin, collected all available mine maps, mine reports, and logs of old drill holes in the inundated area. From a careful study an appraisal of these data, the reserves in the block were calculated at 20,647,800 tons of ore containing 606,440 tons of 60-percent zinc concentrates and 46,970 tons of 80-percent lead concentrates. The ore was estimated to contain 1.76 percent recoverable zinc and 0.18 percent recoverable lead.

Jan 1, 1949

By C. O. Ruud, R. E. Siemens, D. Chandra

The mineralogical constitution of a lateritic ore dictates the type of metallurgical process that can be used to extract valuable metals such as nickel and cobalt . To provide needed mineralogical information on the interrelationships of the metals contained in domestic laterites , the Bureau of Mines awarded a grant to Denver Research Institute to study the transition - type , low - grade laterites found in northern California and southern Oregon . For comparison , limonitic - type laterites from New Caledonia and the Philippines were also studied . X-ray diffraction , electron microscopy , electron beam analysis , and conventional petrography were used to determine the mineralogical associations of nickel and cobalt in the laterites . Results showed that for both laterite types studied most of the nickel and minor amounts of cobalt are associated with the mineral geothite ( FeO ( OH ) ) . Most of the cobalt and minor amounts of nickel are associated with a mixed manganese oxide (wad ) mineral .

Jan 1, 1983

By Fred D. DeVaney

Copper sulphate is a common flotation reagent for blonde ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation food may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it, is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss. That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.

Jan 1, 1929

By E. P. Youngman

Tantalum is a rare element ; estimates indicate that there is less tantalum than gold in the earth's crust . After remaining a laboratory curiosity for many years , it was used to a limited extent and for relatively few years (1903- 1911) for incandescent electric-light -bulb filaments . Another wave of interest in tantalum appeared when its electrolytic-valve action was taken advantage of in charging storage batteries , especially for radio work . Tantalum chargers were eventually displaced by other types of chargers , but for a time they were manufac tured in sufficiently large numbers to create a demand for the metal and to bring about its production on a commercial scale in the United States . As tantalum became available in larger quantities and at substantially lower prices , and as high prices for platinum encouraged the employment of tantalum as a substitute , the metal was put to many new uses . Ferrotantalum was made and sold before the World War , and patents have been taken out for a number of special alloys for industrial purposes , but probably the largest use for the metal to-day is in vacuum tubes .

Aug 1, 1930

By R. S. Fowkes

A study was made by the Bureau of Mines of the penetration of selected granular materials in an unconfined state by wedge-shaped tools having dimensions comparable with the dimensions of the particles composing the materials. The output force for larger particles fluctuated radically. A custom-designed integrator was used to obtain work as a function of depth of penetration in the form of smooth curves. The influence of wedge angle, depth of penetration, penetration rate, entry angle, compaction state, and particle size on the force required and the work performed was ascertained. Empirical equations describing force and work as a function of penetration were obtained for each set of experiments.

Jan 1, 1973