Search Documents

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines collected and analyzed overcore measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 2010

By Ludwig Schmidt

The attention of operators of oil-producing properties long has been directed toward methods of' disposing of petroleum wastes as well as the disposal of oil-field brines. The problem of disposing of' petroleum wastes is not easy to solve, and although many operators are to be commended for the efforts they have made, much work remains to be done before the problem can be considered solved. Petroleum wastes include emulsions of petroleum and brine or mixtures of petroleum and sand that cannot be "broken down" or treated economically by known methods of separating petroleum from deleterious matter; crude petroleum that escapes from pipe lines, fittings, and tanks because of holes in the lines, leaky connections, or some accident; and oil-saturated materials that accumulate accidentally or otherwise an the normal operation of an oil-producing property.

Jan 1, 1938

By Ludwig Schmidt

[The attention of operators of oil-producing, properties long has been directed toward methods of disposing of petroleum wastes as well as the disposal of oil-field brines. The problem of disposing of petroleum wastes is not easy to solve, and although many operators are to be commended for the effort they have made, much work remains to be done before the Problem can be considered solved. Petroleum wastes include emulsions of petroleum and brine or matures of petroleum and sand that cannot be "broken down" or treated economically by known methods of separating petroleum from deleterious natter; crude petroleum that escapes from pipe lines, fittings, and tanks because of holes in the lines, leaky connections, or some accident; and oil-saturated materials that accumulate accidentally or otherwise in the normal operation of an oil-producing property.]

Jan 1, 1938

By S. C. Termes

The Bureau of Mines has used Fourier transform infrared spectroscopy (FT-1R) to study in situ reactions of aqueous solutions of potassium ethylxanthate with CU(II)-and Pb(II)-activated sphalerite plates, in which the plates were both the infrared-transparent windows and the reacting surfaces. A copper (I) ethylxanthate formed predominantly with Cu(II)-activated sphalerite, regardless of the activation time. The products formed on Pb(II)-activated sphalerite depended on the activation times; a short activation time (30 min) yielded a lead ethylxanthate-like product, but a long activation time (90 min) yielded a considerable amount of dixanthogen.

Jan 1, 1986

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to pieces weighing as much as 5 tons, a 150-ton batch retort was designed and constructed at the Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11-1/2 feel in inside diameter and is supported in a 92-Foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, is currently being used as the test shale. To date, three runs have been completed. Results of the second and third runs are reported in this paper. The two runs considered in this report are the first of a series of nine to determine operating conditions that will yield maximum oil recovery from a column of mine-run shale. Variables studied :ire the oxygen content of the retorting gas and the space velocity of the retorting gas expressed as ft3 gas/ft3 bed/min. Oil recoveries for the two runs reported are 62.2 volume percent of Fischer assay for the run using higher oxygen and space velocity, compared with 39.3 volume-percent when less oxygen and a Lower space velocity were used.

Jan 1, 1971

Although coal is found in several locations in Virginia, almost all recent mining has occurred in the southwestern part of the state. Potentially minable reserves are estimated at 2.6 billion tons, slightly less than one percent of the national total. Coal ranges from high- to low-volatile bituminous, and seams average three to four feet in thickness. Virginia produces coal with higher BTUs (British Thermal Units) and a lower sulfur content than the national average. Historically its high quality has made Virginia coal attractive for metallurgical coke production and for the export market. Coal production and related industries have a significant economic impact in southwestern Virginia. In the seven coal- producing counties, coal mining is the major industry. In the two largest coal-producing counties (Buchanan and Wise), over 40 percent of total earning is derived from the coal industry. Virginia's regulatory program was conditionally approved December 15,198 1, and received final approval May 8, 1984. Its Abandoned Mine Land Program was approved with the regulatory program December 15, 1981, with emergency program authority approved November 13,1987.

Jan 1, 1992

By J. W. Town

The Bureau of Mines made continuous-circuit beneficiation studies to determine the optimum conditions for concentrating phosphate minerals from the intermediate-and marginal-grade ores of the Phosphoria Formation in southeast Idaho. Intermediate-grade ore was represented by a sample from Georgetown Canyon and marginal-grade ore from the Gay mine near Fort Hall. Two flow-sheets were developed: The first involved roasting, attrition scrubbing, sizing to remove a concentrate, grinding of the oversize, des liming, and flotation; in the other flowsheet roasting was eliminated. Controlled attrition scrubbing was used to remove clay and silt-size quartz particles imbedded in the phosphate pellets without breaking the pellets. The minus 35-plus 200-mesh fraction was removed by sizing as a finished acid-grade concentrate. The plus 35-mesh material was ground in a rodmill to minus 35 mesh and recycled to the attrition scrubber. The minus 200-mesh fraction was des limed at about 800 mesh to remove clay slimes and floated with 3 to 4 pounds of emulsion per ton of feed. The aqueous fatty-acid oil emulsion consisted by weight of 3 parts No.2 diesel oil, 3 parts crude tall oil, and 0.5 part water-soluble petroleum sulfonate.

Jan 1, 1967

By W. F. Netzeband

This paper, which describes mining methods and practices at the Rialto zinc-lead mine American Zinc, Lead & Smelting Co., in northeastern Oklahoma, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States, The Rialto mine is in the SE1/4 SW1/4 sec. 20 and the NW1/4 sec. 29, T. 29 N., R. 23 E., Ottawa County, Okla. (fig. 1). The 200-acre property is southwest of and adjacent to the town of Picher in the central part of the Picher field of the Tri-State zinc-lead mining district (fig. 2). Other mines of the company adjoin the Rialto on the east and south. Zinc-lead ores have been mined almost continuously from the Rialto tract since 1916. The property was acquired by American Zinc, Lead & Smelting Co. late in 1951, and the mine was operated thereafter by the Nellie B Division of that company until the end of 1955, when it was subleased to the Residue Mining Co.

Jan 1, 1958

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"An electro-optical method was used to quantify superoxide (SO) release from single rat pulmonary alveolar macrophages (PAM) exposed in vitro to respirable quartz and kaolin dusts and in vivo to quartz. Release was determined by measuring the reduction of nitroblue tdrazolium (NBT) to a diformazan precipitate at 550 nm from video-recorded images of individual cells. In vitro exposure to 0.025 or 0.05 mg/ml kaolin for 40 minutes resulted in no significant differences in either the total diformazan produced (max) or the maximum rate of diformazan production (R)./n vitro exposure to 0.025 mg/ml c1uartz decreased max 38 percent while no significant change was found using 0.05 mg/ml. However, R was decreased 31 percent and 24 percent for the low and high dose, respectively. In contrast, PAM obtained from animals exposed in vivo to quartz dust for two or four weeks in inhalation chambers exhibited increased production of diformazan. However, only PAM analyzed three days post-exposure showed significant increases, while PAM from animals sacrificed ten or 31 days post-exposure were not significantly different from control. The combined in vitro and in vivo quartz results might suggest that there is an initital acute response to exposure that decreases the ability of PAM to produce SO, followed by recruitment of production of PAM with increased SO producing capability. It appears that removal of animals from the source of exposure permits PAM to return to control levels of SO production by31 days. Whether this would be true for chronic exposure remains to be elucidated.IntroductionPulmonary alveolar macrophages (PAM) protect the lungs by phagocytizing foreign debris and bacteria.(1) This process involves ingestion as well as destruction of foreign matter. Phagocytosis usually is accompanied by a respiratory burst which increases cellular oxygen consumption leading to the release of highly reactive oxygen metabolites.(2) These agents have been implicated in the killing of bacteria by phagocytes, but they have also been shown to be toxic and,have been linked to cancer, emphysema, arthritis, diabetes, and other diseases.(3) Toxic effects may be a result of 1) an abnormally low production of metabolites, resulting in damage to lung tissue by the respired bacteria and/or dusts; or 2) an abnormally high production resulting in direct damage to lung tissue by metabolites themselves."

Mar 1, 1989

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1966

By R. L. Brown, H. G. Berger, E. F. Pohlman

"The Bureau of Mines in cooperation with the American Gas Association investigating the relation of properties of gas oils to the gum-forming properties of carbureted water gas. The present report deals with the effects of operating practice on the composition of the light oils from carbureted water gas. A general outline of the gummy meter problem has been presented in a previous paper.*Carbureted water gas is a mixture roughly of 80 per cent water gas by volume and 20 per cent oil gas. The latter, though small in relative volume, supplies more than half of the heating value of the gas under the present-day standard. Therefore, it is logical that the oil used in the carbureting process and the operating practices involved should be subjected to scientific study. Many investigations***** bearing on the aspects considered in this paper have been carried out in the past."

Oct 1, 1923

By W. P. Haynes

To evaluate the potential use of battery-powered vehicles, the Bureau of Mines studied the performance of a battery-powered truck propelled by a 9.6 kw dc motor in considerable detail under various driving conditions. Some of the factors investigated were: Gear ratios, payload (1,468 lb maximum), road grade, stops made per mile, and charging time. With the exception of some difficulty with brush wear, operation and maintenance of the truck was generally trouble-free. On range tests carrying an 868-lb payload a distance of about 50 miles at an average speed of about 19 mph in normal driving, the Bureau's battery-powered truck averaged 1.6 to 1.9 miles per ac kwhr input. Stop-and-go tests indicated that prospects for the use of battery-powered trucks in house delivery service within city limits are good; performance of the Bureau truck was sufficiently high for that type of service. The estimated power cost of 2.65 cents per mile while making 10 stops per mile was attractively low from the standpoint of fuel costs.

Jan 1, 1967

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By Geo. H. Williamson

This paper describing the dredging operation of J. K. Davison & Bro. on the Allegheny River near Pittsburgh, Pa., is one of a series being prepared for and published by the United States Bureau of Mines on methods and costs of dredging sand and gravel in the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of H. R. Hissrich, chief engineer of the Goodman Engine and Machine Co., in compiling details of the dredge construction; of H. H. Stewart, auditor of J. K. Davison & Bro., in preparing cost and performance tables; and of J. R. Thoenen, mining engineer of the United States Bureau of Mines.

Jan 1, 1932

By A. W. Fahrenwald

The logic leading to the development of the experiments in this paper already has been stated in Part I,3 but is briefly as follows: The results of the batch-grind experiments in which time of "grind" and fineness of finished product were the variables, strongly indicated (1) that batch grinding involving a single grind could not be operated under any condition to give maximum mill efficiency, (2) that the, sieve analysis of the feed charge in the mill materially affected the efficiency of the mill, and (3) that the percentage of finished product in the mill is a vital factor in ball-mill efficiency. A laboratory closed-circuit grind technic designed to simulate present closed-circuit grinding suggested itself, in which: a ball mill and a classifier constitute the grinding unit. The features of the closed-circuit grinding system are: (1) Short large diameter mills, (3) rapid flow of pulp through the mill, (3) continuous automatic removal of finished product from the system, and (4) high circulating loads. The high circulating load is a result if the short length of the Mill - that is, of the time the charge remains in the mill - and the small percentage of finished material produced during each circuit of the feed through the mill.

Jan 1, 1930

By H. J. Hager, B. W. Gandrud, G. D. Coe

"INTRODUCTION The reduction of washery losses of marketable coal is a phase of coal preparation important to many of the Alabama coal producers. The problem has wide scope, and this report deals with but one of its several aspects. The investigation on which this report is based was made by the Southern Experiment Station of the Bureau of Mines with the cooperation of the Alabama By-products Corporation and the University of Alabama. The Alabama Byproducts Corporation provided samples of table middlings from its Colta washery on the Mary Lee bed at Flat Creek, Ala.PRACTICE AT THE COLTA WASHYAt Colta run-of-mine coal is crushed in a hammer mill in closed circuit with 5/16-inch square-mesh vibrating screens and tabled without classification on eight rectangular-deck wet tables. The coal is more friable than the bone normally present, and hence the bone is concentrated in the coarser sizes. An unclassified feed of this character can not be tabled with high efficiency to low ash content because of the sizing action of a concentrating table, which is such that when the tables are adjusted to exclude the coarse bone from the washed coal, a large amount of fine coal is lost in the middlings. At the time this investigation was undertaken there was no market outlet for middlings, with the result that middling products had to be discarded with the refuse."

May 1, 1939

By D. G. Kuehn

Positive ion sampling studies have been conducted on do discharges containing 0.33 percent sulfur dioxide in helium. Measurements were made for normalized gas pressures from 0.45 to 6.8 torr and discharge currents from 5 to 40 ma. Ion species observed included SO+, S+, SO2+, SO3+; O+, and 0+, 02+. Studies were conducted on the functional dependence of the various ion species with respect to axial distance, pressure, current, and gas flow rate. Interpretation of these results is consistent with the assumption of SO2 dissociation. Deposition of sulfur compounds was observed in the plasma container during these studies. The present results are compared with previous studies which have been conducted in SO2.

Jan 1, 1971

By Seth C. Schaefer

The Bureau of Mines investigated the thermodynamic properties of Bi203 (bismuth sesquioxide) and Sn02 (stannic oxide). Standard Gibbs energies of formation (AGfO) of these compounds were determined with high-temperature electromotive force (emf) cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained from the cell

Jan 1, 1984