Search Documents

By Lloyd A. Morley

Two mine electrical power system simulations are presented. The first is a batch processed procedure capable of modeling a single mining machine consisting of a number of motors operating under various loads. These loads are the mechanical torque loads present at the motor shaft. The second simulation is a more flexible tool for modeling entire mine electrical power systems~ Detailed analyses of bus voltages, transmission-line power flows, and machine behavior are possible. This simulation operates interactively and the power system is configured as the user responds to program generated questions and requests. Development of the theory behind the programming, as well as detailed explanations of the models, is presented. Examples are provided to demonstrate simulation capabilities.

Jan 1, 1978

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By R. E. Kennedy

The presence in air of combustible cases and vapors can constitute an extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and has published Its findings. 4/ The explosibility of ethane has been studied, and its limits of flammability have been determined and published. The development of secondary recovery methods of stimulating oil production has intensified interest in the effect of high pressure on the explosibility of natural gas-air mixtures. The limits of flammability of natural gas-air mixtures at pressures ranging from 50 mm. Hg to 350 p.s.i.a. have been determined and published. More recently, the limits have been determined at pressures up to 3,00C p.s.i. in mixtures of natural gas-air-nitrogen.

Jan 1, 1950

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By W. D. Ryan

The organic act passed by Congress in 1910 instituting the Bureau of Mines provided that the director of the bureau should promulgate such investigations as might be necessary to determine the causes of mine accidents and the best methods of preventing them. With the object of accident prevention in view, Director Joseph A. Holmes, and others who were pioneers in the bureau, conceived the Plan of having first-aid and mine-rescue training as one of the major activities of the Bureau. Out of this plan grew the first-aid and mine-rescue contests, which have been featured as an incentive for men to take courses in this type of mine safety training. The first appropriation for mine-accident investigations became available on July 1, 1908, under the jurisdiction of the U. S. Geological Survey, with Dr. J. A. Holmes in active charge. During 1908 there had been some first-aid training in the Pennsylvania anthracite field and a start made in Illinois, although there appears to be no exact information as to when or where first-aid training in the mining industry first became a reality, it is generally conceded that the St. John's ambulance corps of Scotland was one of the first - if not the first - to make the work effective. In 1911, to celebrate the establishment of the Bureau of Mines and the formal opening of the Pittsburgh, Pa., station, a first-aid and mine-rescue demonstration was conducted on Forbes Field, Pittsburgh. President William Howard Taft and many other men notable in public life were 2 resent. This was the first general national contest of the kind held it the United States; and since then there have been a number of nation-wide first-aid and mine rescue contests, as well as some which have been international in scope. There are over one hundred first-aid and mine-rescue contests of various kinds held annually in connection with mining and the allied industries.

Jan 1, 1929

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a method for determining the helium-3 CHe) content of natural gas and mixtures eontaining 0.5% to 100% helium. The helium is preconcentrated by passing samples through anhydrone, a liquid-nitrogen-cooled chareoal trap, and a titanium absorption trap. The mass spectrometer used to analyze the samples is tuned to 3He at mle ::=; 3.016. Hydrogen deuteride (HD+) interference is minimized by the titanium absorption trap and high instrument resolution. Sample measurements are compared with identically made measurements of a gravimetrically prepared primary standard. The method has a limit of detection of 0.15 ppb with a relative deviation of 13% below the 1~ppb level. The relative deviation is less than 7% for gases eontaining over 100 ppb 3He. The helium isotope ratios of natural gases from the Bureau's Tuck-Trigg Dome Red Cave, the Bush Dome Red Cave, and the Bush Dome Brown Dolomite Formations are distinguishable from one another and from the isotope ratio of crude helium produced from the Panhandle-Hugoton Gasfield.

Jan 1, 1990

By Irving Hartmann

Following the severe starch-dust explosion in the casting department of a large candy factory nearly 2 years ago, great interest has been shown in the explosive properties and the safe manufacture and handling of powdered starches. Under the auspices of the National Fire Protection Association, a committee has been formed to prepare a code aimed at preventing dust explosions in the confectionery industry. One objective of this code will be to reduce the explosion hazards of starches that are widely used for molding, dusting, and other candy-manufacturing processes. The explosibilities of starches and starch mixtures have been studied in the laboratories of the Bureau of Mines and elsewhere. The results of the initial experiments made by the Bureau on 10 samples of cornstarch and mixtures of cornstarch with other materials have been published. In response to numerous requests for additional information, further laboratory studies have been conducted. Data have been obtained on the effects of dust concentration, particle size, moisture content, admixture of .calcium carbonate, and on the effect of oil treatment on the explosibility of cornstarch. The results of this investigation are summarized in this report.

Jan 1, 1950

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969

By C. W. Owings

The Bureau of Mines has conducted a survey to determine potential exposure of mine workers to dust produced in connection with intermittent rock drilling in coal mines. Eighteen mines in 3 states were visited, and 30 different operations were observed, as follows: 10 drilling in draw slate, 8 drilling top rock for brushing or grading, 2 drilling in the coal face, 4 drilling in the bottom, 2 drilling top rock for overcasts, 2 drilling in faults or boulders, 1 drilling for roof bolting, and 1 drilling for trolley hangers. Dust respirators were worn by drilling crews during 16 of the 30 operations. Three hundred thirty-two samples of air-borne dust were collected during the survey. ACKNOWLEDGMENTS The information in this report is based on samples collected and observations made in bituminous-coal mines. Operating officials at these mines have contributed to this study, and their cooperation is gratefully acknowledged. All samples were counted by Thomas B. Kirby, chemist, and Dominick A. Ambrosia, scientific aid, and were analyzed by Gretta S. Baur, physicist, and Patricia M. Gussey, scientific aid, of the Health Branch of the Bureau of Mines.

Jan 1, 1953

By R. R. May

A preliminary examination of the Houston strip-coal mine, situated on the Alaska Railroad at milepost 175 (61 rail miles north of Anchorage, Alaska) and a review of all available information resulting from early coal exploration activities in the area resulted in plans to investigate the coal-bearing formations at depth by means of diamond core drilling to indicate the existence of additional reserves of coal in close proximity to railroad transportation, where it would be quickly available to meet rapidly expanding military and civilian fuel requirements. From the date of mobilization of equipment, August 28, 1951, until date of suspension, August 18, 1952, 2,010 feet of diamond drilling was completed. Ten definable coal beds were cut, of which 2 appear to be persistent and minable over an area of approximately 1/2 square mile. Within this area the 2 minable beds contain approximately 5,000,000 tons of coal in place. Of the remaining beds, at least two others may be minable to the eastward near their projected outcrops; however, these and deeper beds (at least in the vicinity of the drill holes) lie beneath a zone of pressurized gas and brackish water. From a practical standpoint, continued development and utilization of the coal in this vicinity will depend on the operators' ingenuity in developing cheap mining methods and on diligent prospecting for strippable coal under the comparatively light glacial cover.

Jan 1, 1957

By Bruce Maxwell

The deformation modulus of coal mine pillars theoretically can be reduced by drilling holes in advance of the mining face. This reduction of modulus along the edge of the pillar has the effect of decreasing the stress concentration in the roof; control of roof caving is thereby predicted. Initial field work indicated that a high horizontal stress field existed at the field test site: Subsequent field work was undertaken to confirm the high horizontal stress field and to attempt to relieve the horizontal stress in the immediate roof. A method of softening pillars in conjunction with normal mining activity was developed. Instruments to measure horizontal roof strain, roof parting, roof tilt at the rib, and changes in vertical and horizontal stress in the roof and in the coal were used. These instruments were installed in both softened and unsoftened entries and in locations to indicate the effect of vertical slots in the roof. Significant stress reduction due to pillar softening was indicated, but the effect of this reduction on roof stability was not established. The vertical roof slots relieved the horizontal stress in the immediate roof very effectively, and observations of roof conditions indicated that the slots definitely improved roof stability.

Jan 1, 1977

By G. W. Birge

Fifteen coal samples, representing the Winifrede, Chilton, Alma, No. 2 Gas, Powellton, Eagle, Douglas, Sewell, Beckley, Pocahontas No.4, and Pocahontas No.3 beds in Wyoming County, and five samples, representing the Fire Creek, Pocahontas No.6, and Pocahontas No.3 beds in Mercer County, W. Va., were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses and agglutinating values were determined for all coals. The coals were mostly strongly coking and low in ash and sulfur content. Dry, mineral-matter-free fixed-carbon content of the Wyoming County coals ranged from 63.0 to 83.4 percent. The Mercer County samples were all low volatile in rank. Yields of carbonization products were generally in accord with yields from similar rank coals of the Appalachian region. Because of their expanding tendencies, most of the medium-and low-volatile coals would require blending with lower rank coal for normal coke production.

Jan 1, 1965

By J. J. Hoeppner

Lignite samples were collected so as to be widely representative of the extensive deposits in the western north-central area. These were carbonized at temperatures ranging from 450° to 550° C., according, to a standardized procedure. In general, product yields varied; extremes obtained on selected samples show char recoveries on the moisture- and ash-free basis as 56.7 percent for slack lignite or "leonardite" to 80.8 percent for a concentrate of the fusain component from a typical face sample; normal lignite samples averaged approximately 70 percent. Tar-plus-light-oil yields ranged from 3.3 percent for the fusain concentrate to 11.0 percent for a normal sample, averaging approximately 8 percent; gas recoveries varied more widely both in yield and in composition, ranging, from 10.0 percent to 27.7 percent, the latter being from leonardite and quite high in carbon dioxide. Sampling was conducted with the view of representing, as nearly as possible, all beds delineated by Brant (2);4/ many are necessarily missing since collection was confined largely to worked deposits. Data presented in this report indicate a general uniformity of North-Central lignite in respect to low-temperature carbonization, with a few possible exceptions of a local nature. When processed according to the indicated conditions, maximum tar yield may be realized with minimum loss of recoverable heating value of the original coal. Natural weathering of lignite, however, does affect tar yield adversely and should be held to a practical minimum in any commercial operation.

Jan 1, 1956

By W. D. Mcmillan

The Dempsey tract in Washington County, Mo., had a small production of lead-zinc ore from shallow workings. Old dumps from early-day lead mining contain about 25,000 tons of ore averaging about 3 percent combined zinc and lead. Because of the urgent war requirements for lead and zinc, the Dempsey property was examined by Otto Ruhl, formerly an engineer of the Bureau of Mines in August 1942 and selected for further investigation by churn drilling twenty holes totaling 1,309 feet were bored in the fall of 1943. The results of the work are presented in this paper.

Jan 1, 1948

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1985 was $405.9 million, a slight decrease from the record high of 1984. With the exception of clays, output of most nonfuel minerals increased over that of 1984. Alabama was second in the Nation in production of crushed marble and bauxite; third in firre clay; fourth in masonry cement and kaolin; fifth in portland cement and lime; and sixth in ferroalloys and recovered sulfur, Alabama ranked 20th in the Nation in value of nonfuel minerals produced, but ranked 13th in value of industrial minerals. Valuewise, Alabama produced 2.4% of the Nation's industrial minerals.

Jan 1, 1987

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By Kenneth H. Johnston

For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meetings of the Kansas-Oklahoma Waterflood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1960 spring tour of four waterflooding projects in Greenwood County, Kans. (fig. 1). Three of the projects produce oil from the Bartlesville sand, and one produces from the Cattleman sand. The Bartlesville-sand floods have been in operation from 4 to 12 years and have produced about 3,910,000 barrels of waterflood oil from the injection of approximately 64,715,000 barrels of water, a cumulative water-injected to oil-produced ratio of 17 to 1. The Cattleman- sand flood, which has been operating for 3-1/2 years, has produced about 842,000 barrels of waterflood oil from the injection of approximately 9,305,000 barrels of water, a cumulative water-injected to oil-produced ratio of 11 to 1.

Jan 1, 1960

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979