Search Documents

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By E. D. Gordner

Irrespira ble gutses issuing from the rock fofflb tions ere tJ source of expense ond danger in some metGLl mines. There is a great Variation in the compos i-· tion of such gdses and, os shown 'by recent sampling by the Bureau of ines, the gas rr;;,.y consi$t mostly ct carbon dioxide, (Rocle Strata Gtsses in the Mines of the East Tintic Mining District, by G. E. McElroy, Bu.retau of Mines Serial 2Z75) or f methone (Metruine in Ccalifornia C.old Mines, by B. 0. Picl-Q:lrd i:lnd !.. D. ("iordner, Bure, cf Mines Serial 2303), or nitrogen, sin the present instonce. A nl.liilber of unventilated rt:t.ises in some of the mine of l:l Neva&. district conuin «i'ccumulCltions of l;i hih-nitrogen gas the1t will not supi:ort life or combus­tion. The rdises ore in different geologiecil formations and in widely sep1:1rated. loecslities in the mining district. One ot" two ri::lises in the sme fc.rtr.ation may be full of the gos cand einother nec-r'by be t'ree ot· it. Lives have been lost t:lnd a number of men heave been overcome on enteing unvetilated rtsises in which their­respircable tss hcsd c1ccuni..1.l1::1ted between sldfts. Gener1:1lly, however, the gas see:ns to noozett from the .t'onrbtio:1 ond to ecc1: .. ,i.-1,;.1:.1te so slowly tMt its presence is not suspected t the tfr.1e, bu.t discovered. ed:'t&.c' the raise is t)band.oned. OcCE.isionelly 1 t issues from a ne•.,ly cut cre·tice or fissure under considerca ble pressure and in lar!?e enough '3.'16ntities to overcome or drive 011t men working in unventilated places.

Dec 1, 1922

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

By A. B. Hooker

Many attempts have been made to develop methane detectors that will be safer and more accurate than the flame safety lamps used to detect methane in mines. The development has taken two general forms, namely: (1) Methane detectors, in which the evidence of methane depends entirely upon changes in the appearance of the detecting element, such as a flame or filament; (2) indicating methane detectors or those equipped with scales upon which the approximate percentage is definitely indicated. As an aid in the development of suitable detectors, the United States Bureau of Mines has assembled and published in its Schedule 8B a set of minimum requirements which tests and experience have shown desirable for methane detectors. Any manufacturer may submit his detector for inspection and tests leading to approval under this schedule.

Jan 1, 1930

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By Jr. East

The Bureau of Mines conducted an investigation of the Nightingale tungsten deposit about 38 miles north of Fernley, Nev., from September 1939 to March 1940, to determine possible resources of tungsten ore. The property was owned by the Gold, Silver & Tungsten, Inc., which maintained its offices in Boulder, Colo. Ore was discovered in 1917, and some ore was mined in 1918 and treated in a mill at Toulon, a station on the Southern Pacific Railroad, 40 miles east. Same shipments were made since 1918, but no production figures are available. The ore is mined from nearly vertical tactite bodies at the limestone-granite contact. The Bureau of Mines excavated 944 linear feet of trenches, drifted 52 linear feet, sunk a shaft 20 feet in depth, sampled the underground workings by cutting 743 linear feet of channels, sampled the surface trenches by cutting 415 linear feet of channels, and drilled 9 diamond-drill holes, totaling 3,000 feet. The ensuing sections note the location and physical features of the district and specify the property and ownership. The history of the mine is briefed, and the geology and mine workings are described. The work done by the Bureau of Mines is summarized and supplemented in detail by assay maps, logs of diamond-drill holes in appendix A, and a table of sample analyses in appendix B.

Jan 1, 1950

By Ervin P. Fuchs

Volume II of this report presents the vibration data, octave band data, one-third octave band data and narrow band (amplitude versus frequency) data for ten mining machines. These ten mining machines include a Goodman 968-2 Loading Machine, a Lee Norse 245 Continuous Miner, a Jeffrey 120L Continuous Miner, a National Mine Service 3080 Continuous Miner, Acme D-1 Roof Bolter, a Lee Norse 265 Continuous Miner, two Jeffrey Locomotives, a Joy CD-71A Coal Drill and a Jeffrey 100L Auger Miner. Volume J of this report presents the effects of underground environment and loading conditions on noise levels of coal mining equipment

Jan 1, 1979

By William O. Vanderburg

Some mines after passing through the prospecting stage and becoming sizable enterprises still adhere to the development program of the prospect, extending their workings without definite plans. In mining operations where definite structural conditions do not exist, a prearranged layout of mine development is not feasible; but where exploration and preliminary development have indicated the extent and probable limits within which the ore is expected, careful planning of development will result in a lowering of mining costs and a consequent increase is profits. A lack of definite plane for laying out mine workings is one of the contributory factors to unnecessarily high costs. Although this paper deals primarily with the influence of level spacing on mining costs, still other phases of mine development, such as the proper spacing of ore chutes and raises, can be analyzed on a cost basis in a similar manner, as shown herein. LEVEL SPACING The problem of establishing a new level or levels in order to exploit steeply dioping ore deposits and prospect the ground at depth recurs at intervals during the active life of mines. Driving levels is largely "dead work" and therefore costly. By the judicious selection of the proper level interval after balancing the opposing factors involved in the problem, a considerable saving in mining costs can be effected. Although much has been written in regard to the various methods employed in ore extraction, mining literature is still incomplete in regard to the factors-influencing level spacing at various mines. Level spacing involves procedures not lending themselves readily to description, and, moreover, it is a phase of mining operations that is apt to escape criticism, because only those in close contact with the operations are equipped with the necessary familiarity with the conditions to pass judgment.

Jan 1, 1932

By John Soule

The Torpedo copper mine in the Organ Mining, District, Dona Ana County, N. Mex., was discovered in 1899, and production of copper from oxidized-ore deposits was begun in 1900. Production continued through 1907, but operations were only intermittent frown 1907 through 1921. The production of copper during these periods amounted to about 3,500,000 pounds. Reserves primary sulfide copper ore were believed to occur below the old workings, and after a detailed examination of accessible workings and a study of drilling records of several private companies by an engineer of the Bureau of Mines, a development program of diamond core drilling was initiated. This investigation was started October 3, 1949; and completed April 30, 1950. Four holes totaling 2,122.3 feet wore diamond-drilled, and 70 samples were analyzed. All drilling was done with a Government-owned hydraulic-feet drill having special rods and core barrels to increase the recovery of core in critical zones. This report describes the location, history, ore deposits, and factual data obtained by the Bureau of Mines from the drilling.

Jan 1, 1951

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963

This report presents production and delivered costs for coal exports from the five major Western coal-exporting countries: Australia, Canada. Colombia, South Africa, and the United States. Cost data were compiled from visits to 43 mines by U.S. Bureau of Mines engineers between 1985 and 1990. All report costs are in January 1989 U.S. dollars per short ton. Production costs for raw coal are divided into mining and regulatory categories. Costs are broken down by type of cost, type of mine. and country. Scheduled operating and capital costs for raw coal were processed by the Bureau's MINSIM discounted cash flow program to determine total production costs calculated at 0% and 15% discounted cash flow rates of return (DCFROR). Delivered costs are for salable coal delivered to various markets. Costs are broken down by supply country, market, and type of cost. Scheduled operating and capital costs for salable coal were processed by the Bureau's MINSIM discounted cash-flow program to determine total salable coal costs at 0% DCFROR. Added to total salable coal costs were transportation and port costs to get delivered costs. Comparative overview information on the coal industries of the five study countries are appended. This appendix includes information on industry economics and exports, production and reserves, and coal industry issues.

Jan 1, 1993

By Edward F. Redente

Several research projects have been conducted in the western United States to determine the optimum soil replacement thickness for reconstruction of rangeland and cropland. However, the information gained from these studies tends to be site-specific and not broadly applicable. Moreover, the possible interaction between soil thickness and mechanical and fertilizer manipulation of the overburden has not been adequately studied. To meet these information needs, research was initiated at Trapper Mine in northwestern Colorado in 1980 to study vegetation response to soil thicknesses of 15,30,45, and 60 cm and five manipulations that included disking, ripping, and fertilizing. All crops were harvested at peak standing crop and then weighed in the laboratory. Wheat grain yields were highest when soil thickness was 45 cm and the soil and overburden were ripped. Alfalfa yields appeared to be highest when overburden was disked and fertilized and soil was replaced to a thickness of 60 cm. For range vegetation, standing crop biomass was highest when overburden was ripped and soil was replaced to 60 cm thick. However, optimum performance was obtained from the maximum number of species and life forms by disking overburden and replacing 15 cm of soil. The performance of most range plant species has improved over the three years of the study. When the results of this study are compared to the results of other soil thickness studies, we can conclude that selection of management practices should be influenced by local climate, local soil and overburden conditions, type of crop or vegetation to be grown, and specific management goals for that crop or vegetation.

Jan 1, 1984

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By Wilbur I. Duvall

Twelve millisecond delayed blasts in four limestone quarries in Iowa were instrumented with arrays of vertical velocity gages to determine if the direction of propagation through the rock or the method of initiation of the blast had any effect upon the level of vibration. Two gage arrays approximately 90° apart were used to test the effect of direction of propagation. The vibrations from blasts initiated by three methods were recorded. Vibration records from these tests were analyzed for peak particle velocity as a function of distance from the blast. The data are shown to fit a power Law equation. Direction of propagation is shown to affect the value of the exponent n. The effect of charge size per delay interval on the level of vibration is removed from the data by scaling the travel distance by the square root of the charge weight per delay period. The method of initiating the blasts is shown to have a strong effect upon the level of vibration and the spread in the data from one shot to another.

Jan 1, 1963

By P. G. Kovalchik

Safe electrical operation of shuttle cars depends upon maintaining the trailing cable's conductor temperature below 90° C. However, trailing cables are wound on and off reels, which changes the heat transfer characteristics of the cable-reel system. Derating factors for trailing cables are an attempt to adjust for this changing heat transfer mechanism in a practical way. The U.S. Bureau of Mines conducted research to determine acceptable derating factors for reeled mine trailing cables, using four cable-reel combinations, representative of industry usage. Cables were continuously and intermittently loaded at different duty cycles with direct currents of different magnitudes. Relationships between the average temperature rise and current load were established for each layer of each cable. Two models were constructed; one used empirical data from the continuous and intermittent load tests, and the other was based on thermodynamic theory. Results obtained from the theoretical model were compared with those from the empirical model for the rated temperature rise of the cable. Both models can be used to simulate a variety of test conditions including those that normally cannot be conducted in the laboratory. This information was used to determine acceptable derating factors for each layer of these cable-reel combinations.

Jan 1, 1994

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,421 samples, representing the products of 131 companies. The samples were collected during June, July, and August, 1953. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1954

By M. W. Barger, J. K. H. Ma, J. Y. C. Ma, V. Castronova

The objective of this study was to investigate the effects of various bisbenzylisoquinoline (BBIQ) alkaloids on respiratory burst activity of alveolar macrophages and to characterize the interaction of these drugs with alveolar phagocytes. BBIQ alkaloids were chosen for study because they exhibit a wide range of antifibrotic potencies in a rat model, with tetrandrine being very effective and tubocurarine being ineffective. These drugs inhibited zymosan-stimulated oxygen consumption with a potency sequence of tetrandrine (IT) = fangchinoline (FA) > berbamine (BE) ., cepharanthine (CE) "" cycleanine (CY} ~ tubocurarine (TU). This inhibition of respiratory burst activity could not be attributed to a drug-induced decline in the ATP content of these pneumocytes. Drug binding to alveolar macrophages was directly dependent on temperature and drug concentration. The sequence for binding capacity was FA > TT = BE = CY > CE ~ TU. Therefore, there was no simple relationship between binding capacity and inhibitory potency. Binding capacity was not related to lipophilicity of these alkaloids. In addition, tetrandrine failed to bind to metabolically dead cells or sonicated macrophage preparations. These data suggest that the interaction of BBIQ alkaloids with phagocytes is not simply nonspecific binding to membrane lipids. Alteration of the cytoskeletal system with vinblastine, taxol, or cytochalasin B decreased tetrandrine binding by approximately 33% when adtkd separately and by 93% when added jointly. Pre-exposure of alveolar macrophages to stimulants increased the ability of BBIQ alkaloids to inhibit both oxygen consumption and superoxide release. These data suggest that the mechanism by which BBIQ alkaloids inhibit activation of phagocytes involves microtubules and bules and microfilaments. Pre-exposure of macrophages to stimulants would change the conformation of cytoskeletal components and may make these structures more susceptible to drug interaction.

Mar 1, 1992

By Carl Rampacek

The conversion of dilute sulfur dioxide gas into sulfuric acid by autoxidation in mechanical cells of the flotation or gas absorber types was investigated. Bench-scale tests were made with sulfur dioxide-air mixtures to determine the influence of several factors on autoxidation of sulfur dioxide, using iron and manganese salts as catalysts. The laboratory investigation subsequently was extended to pilot plant acid-making tests, using a modified turbomixer gas absorber having a 12-inch-diameter impeller. Sulfur dioxide gas was produced for the tests by roasting pyrite in a fluidized-bed reactor. In the better tests, made with manganese sulfate as the catalyst, the equivalent of 1,000 pounds of anhydrous H2SO4 was produced per 24 hours as a 10-percent solution; power consumption was 0.2 kwhr per pound of equivalent anhydrous acid synthesized. The batch and continuous tests demonstrated the technical feasibility of producing dilute sulfuric acid by autoxidation of sulfur dioxide gas in mechanical cells when converting pyrite roaster or waste smelter gases.

Jan 1, 1963