Search Documents

By Herman W. Sheffer

This report describes and discusses present-day leaching technology employed to recover copper from low-grade mine and dump materials derived from the exploitation of copper ore deposits in the Western United States. Illustrations of the integral parts of the leaching, precipitation, and recovery operations at several copper-producing companies are presented. Schematic drawings are included to present typical flowsheets of leaching and precipitation operations. Operational problems common to most copper leaching and precipitation plants are discussed. Areas of present and future research to improve leaching techniques are cited.

Jan 1, 1968

By R. Y. Williams

The investigative work described in this report was undertaken by the Bureau of Mines under a cooperative agreement with the department of mining engineering of the University of Illinois and the Illinois State Geological Survey." The purpose of this agreement was to provide for a comprehensive investigation of coal-mining conditions in the State, with especial reference to the possibility of lessening waste in the mining and preparation of coal and of reducing the dangers to which miners are exposed. The Bureau of Mines paid particular attention to those phases of the investigation that were of general interest from their bearing on safety and efficiency in the coal-mining industry as a whole. Thus, it studied the occurrence of gas (methane) in the mines of the southern part of the State," tested the inflammability of the coal dust from many mines, examined the efficiency of the control of ventilating currents, and investigated the factors affecting the humidity of mine air with respect to their bearing on the occurrence of mine explosions. Following the establishment of the fact that under certain conditions dry bituminous coal dust is inflammable, there arose the problem of finding efficient methods of preventing or limiting coal-dust explosions. Experiments in the gas-and-dust gallery at the Pittsburgh testing station of the Bureau of Mines verified the fact that certain dusts that explode violently when dry are rendered inert by proper humidi- .fication of the atmosphere within the gallery, and the importance of humidity as a factor in limiting the inflammability of coal dust in a mine is demonstrated by the fact that there has never been in Illinois a dust explosion during the summer months, whereas the records show a number of dust explosions during cold weather. It is easy to see that the warm moisture-laden air that enters a mine in the summer must deposit moisture on cooling, whereas the cold and relatively dry air that enters in winter must take up moisture as it becomes heated in traveling through the mine.

Jan 1, 1914

By D. A. Elkins

Design plans and detailed cost estimates of mining and treating ore from Maggie Canyon deposit by two alternative methods which can be used in the event of a sudden need to exploit this resource are given . Lower costs are estimated for the operation employing oil - emulsion flotation . The total capital investment required for this operation is estimated at $ 11,750,000 . Assuming an 85 percent recovery in mining , 55.6 pct of the manganese in the ore reserve would report in 153,333 tons of ferromanganese containing 75 pct manganese . The production cost for the 5 - year operation would be about $ 245 per ton of ferromanganese . The total annual operating cost would be approximately $ 7.5 million , distributed , in pct , as follows : Mining 11.9 , milling 24.4 , sintering 9.9 , smelting 47.2 , hauling ore and sinter 2.8 , and general offices 3.8 . Recovery and costs are both higher for the operation employing dithionate leaching . In this operation the required investment is about $ 17,220,000 . Manganese recovery would be 67.6 pct in 186,160 tons of ferromanganese . Production cost would be about $ 284 per ton of ferromanganese . The total annual operating cost would be about $ 10,575,000 , distributed , in pct , as follows : Mining 8.4 , milling 44.4 , sintering 7.4 , smelting 34.7 , hauling ore and sinter 1.3 , and general offices 3.8 . Potential process modifications might reduce the operating cost of the first operation by as much as 7 pct and that of the second operation by as much as 9.5 pct , but exploitation of the deposit by the techniques studied is not economical today .

Jan 1, 1964

By B. W. Naugle

Twenty-nine sole-heated-oven expansion teats were made on 9 different coals, and apparent specific-Brevity tests were made on 12 of the resultant cokes. The coals, which ranged in dry, mineral-matter-free fixed-carbon content from 58.7 to 81.1 percent, were tested over a rather wide range of moisture content and dry-coal bulk density to determine the separate effects of these variables on linear coal expansion. The experimental data support the follow expression relating "as-tested" coal bulk density, moisture content, and linear expansion, [ER = (1-MR) (1+Et) - 1; BDt] where ER = fractional expansion at a reference bulk density of 55.0 lb. of 1 percent moisture coal per cu. ft., Et = fractional expansion at Mt and BDt, MR = reference moisture content = 0.01, Mt = moisture content, "as-tested", BDR = reference bulk density = 55.0 lb. per cu, ft., BDt = bulk density, "as-tested", 1b. per cu. ft.

Jan 1, 1957

By E. P. Youngman

In the Unfederated Malay States, with the exception of Johore, the rights of suzerainty, protection, and administration were transferred by giam to the British Government in 1909. In the States of Kelantan, Trengganu, Kedah, and Perlis, the rulers are assisted by State Councils and by British advisers appointed by the British Government.3 With respect to Johore, the largest, richest, and most highly organized of the Malay States not in the Federation, the treaty of December 11, 1885, with Great Britain, defined the relations of the State to the British Govern- ment and allowed the Maharaja to assume the title of "Sultan"; an amendment to this treaty (May 12, 1914) provided that the Sultan should be advised by a British officer, the General Adviser. ...... The political organization of the States is reflected in the mining legis- lation, Johore being the only one having a comprehensive code. The mining enactments now in force, according to the High Commissioner for the Malay States, are as follows:

Jun 1, 1932

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough so that realistic rate determinations could be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1988

By Sabri Ergun, Robert W. Smith, Victor H. Tiensuu

Factual geometries are considered for X- ray scattering studies of weakly absorbing materials by both reflection and transmission methods . These studies are usually made on slab specimens to obtain adequate scattered intensities ; however , the intensities are appreciably influenced by absorption of the X-rays in passing through the specimens . Conventional equations derived to account for this absorption are based on idealized geometries , but for polycrystalline carbons the use of idealized geometries leads to several percent error in the corrections to be made . Use of factual geometries substantially reduces this error .

Jan 1, 1964

By R. O. Dannenberg

The Bureau of Mines conducted laboratory investigations with the objective of developing an alternative process for recovering cobalt and copper from complex sulfide concentrates. Processes currently used depend largely upon precipitation techniques to remove impurities and recover cobalt from sulfate liquors prepared by oxidative pressure leaching of the sulfide concentrates. The Bureau conducted bench-scale research on a process for treating cobaltite concentrates, comprising (1) oxidative pressure leaching, (2) jarosite precipitation followed by H202 oxidation and pH control to remove iron and arsenic, (3) copper solvent extraction with a mixed hydroxyoxime-amine extractant, (4) copper electrowinning from recirculating acidic strip liquor, (5) selective cobalt extraction from copper solvent extraction raffinate with a phosphinic acid extractant, and (6) electrowinning of cobalt from a recirculating weak acid strip liquor. Overall cobalt and copper recoveries were 91.7 and 84.1 pct, respectively. Electrowon products assayed 99.8 pct Co and 99.89 pct Cu.

Jan 1, 1987

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By W. W. Agey

This report summarizes results of bench-scale metallurgical studies by the Federal Bureau of Mines on three composite samples representative of the low-grade manganese ores purchased by the General Services Administration (GSA) and stockpiled at Deming, N. Mex., and Wenden, Ariz. Bench-scale flotation tests at the Salt Lake City Metallurgy Research Center showed that all three composites could be beneficiated by flotation to recover 88 to 90 percent of the manganese in concentrates that assayed from 38.5 to 39.0 percent Mn, 10 to 12 percent insoluble, 5 percent CaO, 3 to 5 percent Fe, and 1.3 to 1.7 percent combined Pb plus Zn plus Cu, Sintering studies indicated that specification-grade material could be made from these concentrates by sintering above 1,000° C, and adding either sodium or calcium chloride to the charge to insure removal of enough lead and zinc to meet the specifications.

Jan 1, 1962

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in REscent years. The tenative ball-mill grindability method D409-35T4/was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-Mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity. ACKNOWLEDGMENTS This study was conducted at the Southern Experiment Station of the Bureau of Mines in cooperation with the University of Alabama. The Alabama liming Institute was of great assistance in furthering the investigation, and the work was undertaken largely as a result of its request that the Bureau of Mines should make certain studies of Alabama coals. Grateful acknowledgments

Jan 1, 1938

By C. H. Elder

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coal bed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 fts/day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

This report presents production and delivered costs for coal exports from the five major Western coal-exporting countries: Australia, Canada. Colombia, South Africa, and the United States. Cost data were compiled from visits to 43 mines by U.S. Bureau of Mines engineers between 1985 and 1990. All report costs are in January 1989 U.S. dollars per short ton. Production costs for raw coal are divided into mining and regulatory categories. Costs are broken down by type of cost, type of mine. and country. Scheduled operating and capital costs for raw coal were processed by the Bureau's MINSIM discounted cash flow program to determine total production costs calculated at 0% and 15% discounted cash flow rates of return (DCFROR). Delivered costs are for salable coal delivered to various markets. Costs are broken down by supply country, market, and type of cost. Scheduled operating and capital costs for salable coal were processed by the Bureau's MINSIM discounted cash-flow program to determine total salable coal costs at 0% DCFROR. Added to total salable coal costs were transportation and port costs to get delivered costs. Comparative overview information on the coal industries of the five study countries are appended. This appendix includes information on industry economics and exports, production and reserves, and coal industry issues.

Jan 1, 1993

By R. E. Kennedy

The presence of combustible gases and vapors in air can constitute n extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and. allied industries, the U. S. Bureau of Mines has investigated the explosive properties of a number of gaseous and liquid compounds; the results of these investigations have been published in various government papers and journal articles. The increased use of liquefied, petroleum gases has intensified interest in the effect of high pressures on the explosibility of propane-air mixtures. The limits of flammability of natural gas-air mixtures have been determined at pressures ranging from 50 min. Hg to 3,000 p.s.i. As it is known that a combustible. gas or vapor cannot burn or explode when the oxygen content of the atmosphere is less than a certain value, critical values were determined for the oxygen content of atmospheres to which nitrogen had been added as a diluent. In this connection limits of flammability were determined for ethane in atmospheres containing added. nitrogen or carbon dioxide at pressures up to 900 p.s.i.g.

Jan 1, 1951

By John B. Gayle

The suitability of fluid petroleum coke as a blending agent for producing metallurgical coke has been investigated using the Tuscaloosa and sole-heated experimental ovens. From the results of tests with three representative blends, it has been fond that additions of fluid petroleum coke effect the following changes: (1) Increase in size, resistance to shatter, and apparent specific gravity of cokes produced; (2) little or no change in coke hardness and stability or in the amount of breeze formed; (3) increased charge density; (4) modification of expansion characteristics of blends charged; and (5) decreased ash and increased sulfur contents of blends charged and cokes produced. Substitution of a calcined sample of fluid coke of greatly reduced sulfur content resulted in a coke of inferior physical properties. This effect indicates that additions of the calcined product should probably be limited and that other methods for producing a low sulfur fluid coke should be considered.

Jan 1, 1956

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963