Search Documents

By K. R. Dorman

To develop the potential of precast concrete sets as a support medium in underground mines, a three-piece precast concrete drift set was designed for a small opening and tested to destruction in an underground straining frame. Thirty-six tests were made with three sizes of members using three different loading conditions. In addition, 14 members were tested individually in the laboratory. Test results are compared with theoretical calculations. A cost comparison shows the use of concrete sets would be advantageous where conventional wooden timber requires excessive replacement.

Jan 1, 1968

By D. Bienstock, R. C. Kurtzrock, E. R. Bauer, J. H. Field

To remove hydrocarbons and carbon monoxide in automotive exhaust by oxidation , a catalyst of 4.2 percent Uз Og , 1.7 percent Cr₂ 0 , and 1.7 percent CuO supported on 1 /8 - inch y- alumina spheres was tested in a reactor in place of the muffler of a 1 / 2 - ton truck . Tests were made with both nonleaded and leaded gasolines . With the engine at operating temperature , tests were made with the engine idling and with the vehicle cruising at 30 mph . Auxiliary air was added to maintain an oxygen concentration of 3 to 4 percent in the gas leaving the catalytic reactor . The vehicle was operated for 83 hours (about 60 percent of the time with the engine idling ) and 525 miles with nonleaded gasoline . Conversions of 98 percent of the hydrocarbons and 100 percent of the carbon monoxide were achieved with the engine idling and with 7,000 ppm carbon atoms and 4- percent carbon monoxide in the feed to the reactor . Hydrocarbon conversions of 75 percent were obtained at cruising speeds of 30 mph with a feed of 1,700 ppm carbon atoms ; the carbon monoxide concentration was less than 0.3 percent in the feed and was unchanged in passage through the reactor . Identical activity was obtained initially in switching to a gasoline containing 1.9 ml tetraethyl lead (TEL) per gallon . However, there was a gradual loss in activity thereafter . Conversions in tests with the engine idling about 50 percent of the time , had decreased by 23 percent for the hydrocarbons and by 25 percent for the carbon monoxide from their initial values after 122 hours and 1,300 miles of operation with leaded gasoline . The levels of radioactive materials in the exhaust of the reactor and the radiation in the vehicle were negligible .

Jan 1, 1963

By Cleo Griffith Rall

The method for determining the effective porosity, of oil- and gas- bearing sand described in this report is a development of an earlier method devised by Bureau of Mines. The apparatus has been improved and made more convenient to use, but the procedure has been in use for many years without essential changes. A tabulation at the end of the report gives the results of more than 2,000 porosity determinations for oil sands in the fields of 13 states. A selected bibliography of articles containing descriptions and evaluations of various methods of determining porosity Is a. part of this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and ,on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1949

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951

By L. R. Burdick, R. Wiggers, J. F. Berkley

"INTRODUCTION On February 23, 1944, Solid Fuels Administrator Harold L. Ickes stated that the existing fuel shortage made it necessary to utilize a great surplus of freshly mined anthracite ranging in size from Barley (No. 3 Buckwheat) downward through the smaller sizes. As a part of the program to increase the use of such coal, field trials of mixtures of bituminous slack coal and anthracite Barley were made on industrial-size stokers at many fuel-burning plants. The following covers the test information it was possible to accu-mulate during the work of initiating the use of these mixtures at the plants.SUMMARY AND CONCLUSIONSField tests of various mixtures of bituminous slack coal and anthracite Barley on industrial-type stokers show that the use of such mixtures is very practicable and that it is possible to change and usually to adjust to an improved condition the characteristics of a fuel bed of eastern bituminous slack coal by the addition of proper amounts of anthracite. The improved uniformity of the fuel bed of single-retort stokers makes possible less manual attention to the bed. Air flow through the fuel bed is affected.Smoke is decreased. In general, the fly ash and also the unburned combustible in the fly ash and refuse are increased. Clinkering in the fuel bed is generally lessened. The peak-load carrying capacity of the stoker is definitely affected, usually adversely for the higher percentages of anthracite."

May 1, 1946

By H. R. Shell

To obtain a better understanding of the crystallization of fluoride containing amphiboles from melts, an investigation of the range of stability between fluoramphi-boles and other minerals was conducted by the Bureau of Mines. This study has shown that the stability of fluoramphiboles is strongly influenced by both fluoride concentration and isomorphic replacement. Over 150 reactions were made with different compositions and reaction conditions. substitutions attempted and the phases that formed when the composition was crystallized by cooling from the melt are discussed. The attainment of equilibrium in these multicomponent systems is not claimed. Many ions that would be expected to enter the amphibole structure instead resulted in crystallization of phases other than amphibole. Those compositions that resulted in a high yield of acicular fluoramphibole by crystallization from the melts are shown in table 2. The fluoramphiboles obtained from melts typically had an acicular crystal habit and a hardness of 6 to 7 on the Mohs' scale. Although many had relatively high length to cross section ratios, none were fibrous; it was concluded that the possibility of synthesizing a fibrous fluoramphibole from a melt was low. However, many compositions can be crystallized into a tough, hard, impact-resistant mass of interlocking acicular crystals.

Jan 1, 1958

By G. R. Strimbeck

Experimental work is report on the gasification of 90-percent through 200-mesh, strongly coking Sewickley-bed coal with oxygen and with steam in three temperature ranges, namely, 2,700° to 3,400° F., 1,600° to 2,000° F., and 230° to 250° F. Thirty-one runs have been made, during which 56,000 pounds of coal have been charged to the generator at feed rates of 200 to 450 pounds of coal per hour. The average results, not the optimum results, are given in the following tabulation:

Jan 1, 1950

By Larry G. Stolarczyk

An underground medium frequency radio communications system has been developed and demonstrated in both coal and metal/non metal mines. The principal advantage of the system are its low cost, ease of installation and the ability to provide radio communications to any vehicle or roving miner in the underground mine. The system provides high quality radio coverage in work areas and along manways with existing "wireplant" conductors. The conductors include AC power cable, telephone cable, metal water and high pressure air pipes, etc. The measured communications range from the base station to mobile transceiver exceeded 12,500 ft without the use of repeaters. A cost/benefit analysis shows that the initial cost of the equipment can be returned 2-6 times in the first year. The mine productivity increases by approx. 13 percent.

By Robert L. Skaggs

Sixteen nonaqueous techniques conceived to replace the current aqueous scheme for separating hafnium and zirconium tetrachlorides were re- viewed and evaluated by the Bureau of Mines. The methods are divided into two classes: separation by fractional volatilization of the tetrachlorides, which takes advantage of the higher volatility of hafnium tetrachloride; and separation by chemical techniques, based on differences in chemical behavior of the two tetrachlorides. The criteria used to evaluate separation methods were temperature, pressure, separation factor per equilibrium stage, complexity, compatibility with existing technology, and potential for continuous operation. Three processes were selected as being most promising: (1) high-pressure distillation, (2) extractive distillation from a molten salt, and (3) preferential reduction of gaseous ZrC14. Any of the proposed nonaqueous Hf-Zr separation schemes must be supplemented with additional purification to remove trace impurities.

Jan 1, 1984

By A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high-sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations. The survey, which provided information on Appalachian region coals only, indicated that such important coal- beds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14-mesh top size. For many other coalbeds amenability to sulfur liberation by crushing was indicated, although too few samples were available to draw firm conclusions,

Jan 1, 1966

By A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high-sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations. The survey, which provided information on Appalachian region coals only, indicated that such important coal-beds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14-mesh top size. For many other coalbeds amenability to sulfur liberation by crushing was indicated, although too few samples were available to draw firm conclusions,

Jan 1, 1966

By Neal M. Muir

The increasing demand for iron ores prompted the Bureau of Mines to investigate the sources of past production in Kentucky to determine whether reserves of usable ore still exist. Preliminary investigation showed that the holdings of the Rose Run Co. were the most promising, inasmuch as the deposit had not been exhausted by past mining and the property was near railroad facilities and but 80 miles from the blast furnaces at Ashland, Ky. The Bureau conducted a churn-drilling and sampling program to investigate the depth, thickness, and iron content of the ore beds so that they might be evaluated as a possible reserve of low-grade iron ores. The Rose Run area in Bath County, Ky., was explored by 74 churn-drill holes totaling 2,059.4 feet of drilling and 4 cuts and test pits. Fifty-seven drill holes and the four test pits penetrated the ore bed at an average depth of 22 feet. The bed had an average thickness of 2.54 feet. Analyses show that the calcium and magnesium carbonate content is more than sufficient to flux the silica and provides an excess that needs an admixture with other siliceous iron ores.

Jan 1, 1950

By J. Sammarco

Proper illumination is critical to a miner?s ability to detect hazards in underground mines. Moving hazards are often located in the miner?s peripheral field-of-view, while slip/trip/ fall hazards are often located in the forward field-of-view. The objective of the research described in this paper was to determine if light-emitting diodes (LEDs) improve visual performance as compared to traditional incandescent (INC) cap lamps. The research presented focuses on comparative studies of a National Institute for Occupational Safety and Health (NIOSH) prototype LED, a commercial LED and an INC camp lamp. Thirty subjects participated in these studies, with ten subjects in each of the following age groups: 18 to 25 years, 40 to 50 years and 51+ years old. Visual per­formance was quantified by the subjects? speed and accuracy in detecting hazards, while visual performance for disability glare was quantified by the use of contrast sensitivity tests. Results suggest that LEDs with a visible spectrum containing a higher concentration of the shorter wavelengths can enable visual performance improvements with respect to disability glare, the detection of moving hazards in the peripheral field-of-view and the detection of floor hazards in the forward field-of-view. The NIOSH prototype LED cap lamp provided the best visual performance improvements for the older age groups in every test.

Jan 1, 2009

By T. Muldoon

Literature review and extensive field survey of line and check curtain materials and practices showed: ? Miners, in general, know how to set tight curtains, and do so when needed. ? The tradeoff is economic; tight ventilation is labor-intensive. Line and check curtain techniques found are catalogued and evaluated. A fieldworthy 10 ft extensible brattice to maintain a 10 ft setback was found in use in two mines on continuous miner faces. This technique was evaluated in the laboratory for leakage and methane control at the face. Significant results include: 1) Air leakage through a gap in the extensible curtain depends upon the ratio of the cross-sectional areas between entry and return as well as gap area; 2) Gap shape has no significant effect on methane concentrations at the face -increasing gap area diminishes ventilation effectivness; and 3) Substantial reductions of CH4 concentrations at the face were accomplished by brattice extensions with gaps of up to 5 ft2 in area. An "inby hook," inserted in the roof automatically to make possible the deployment of a longer (20 ft) brattice extension in the context of a remotely controlled miner, was tested in various roof types. Insertion of this design succeeded only in coal.

Jan 1, 1982

By E. K. Stanek

This report contains the results of an investigation into the feasibility of periodically measuring parameters of the insulation for a mine electrical power system in order to detect incipient faults. The variety of insulation parameters evaluated included insulation resistance, dissipation factor, power factor (vs. applied voltage), current harmonics, leakage current, infrared radiation, as well as certain circuit breaker parameters and tests. In order to augment field tests a program of accelerated life testing was also carried out. Apparent inconsistencies in data were identified as the result of environmental effects, primarily temperature and relative humidity. A series of environmental tests were conducted to develop correction factors that allow one to refer measured parameters to standard conditions. A portable data collector was develop-ed to aid in the accurate collection and analysis of laboratory and field data. The primary conclusion is that insulation deterioration can be measured and failure predicted with reasonable confidence. The secondary conclusion is that most of the tests are impractical in the field although useful in the laboratory. Infrared sensing, insulation resistance and dissipation factor are the best insulation field tests when portability is taken into account.

Jan 1, 1979

By T. A. Hendrickson

The Bohemia district, situated about 30 miles southeast of Cottage Grove, Oreg., in the Calapooia Range, has been the major producer of lead and zinc in Oregon. Sporadic production has been Maintained from the district since its early discovery about 1858. In 1942, a selective-flotation mill was built at the Champien mine, which operated for only a short time and was forced to close because of the war and lack of labor. The Champion mill reportedly has been operated as a custom mill for the treatment of ore from the Musick and Helena mines, located in the district sometime in the past. This report summarizes the results of laboratory ore-dressing studies made on ore samples from the Musick and Helena Mines.

Jan 1, 1951

By C. A. Komar

The Bureau of Mines is investigating possible applications of acoustic energy at sonic and ultrasonic frequencies in petroleum production. A phase of this work involves measuring sound velocity through petroleum reservoir rocks. References and abstracts were prepared as a bibliography to make available to others some of the material obtained from a literature search covering the past applications and the present uses of sound. Laboratory and theoretical studies of the various parameters that influence the velocity of sound in porous media account for the wealth of information now available. Velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity logging systems, capable of measuring speed of sound waves in underground formations penetrated by wells, have been developed for interpretative studies. The close relation between acoustic velocity and porosity makes it possible to determine porosity from velocity logs. Most velocity log interpretation in terms of porosity is based on a formula developed by Wyllie and others known as the time-average relation.

Jan 1, 1963

By John C. Machisak

The thirty-fifth consecutive National Safety Competition sponsored and conducted annually by the Federal Bureau of Mines, Department of the Interior, closed with several noteworthy accomplishments to its credit. Some of them are: 1. A record low injury-frequency rate of 18.293 disabling work injuries per million man-hours equal to that established in 1957. 2. The third lowest injury-severity rate (4,335). 3. The second highest number of mines and quarries participating (672) 4. A record number of participants finishing the competitive year without a disabling work injury. 5. All recipients of Sentinels of Safety trophies free of disabling work injuries for the first time since 1952.

Jan 1, 1961

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1968

By John R. Bitler

The Bureau of Mines conducted this study to provide information concerning the availability of and the demand for construction-mineral aggregates in the Baltimore, Md., Standard Metropolitan Statistical Area (SMSA). The demand is discussed with reference to the area's current consumption and estimates of the area's demand for aggregates through 1990. Estimates of aggregate supply are presented in conjunction with an examination of the geology of the area, the availability of substitutes, and the effect of transportation costs. A discussion of the constraints affecting aggregate availability precedes the conclusions and recommendations. The availability of aggregates is subject to geologic, economic, and political constraints. As of January 1974, an estimated 20,100 million tons of stone was available to meet the demand projected through 1990 (188.7 million tons). An estimated 139 million tons of sand and gravel was available to meet the demand projected through 1990 (84.3 million tons). Several alternative actions are available within the area to insure the adequacy of the stone supply and to increase the supply of sand and gravel: (1) The establishment of special mineral resource zones; (2) the application of sequential land use techniques; and (3) the exploration of previously undeveloped regions.

Jan 1, 1975