Search Documents

By Edwin B. Cook

This report presents the results of calculations of the equilibrium composition of the products of combustion with air of six different mixtures of octane CgH18, plus PbEt4 and halogen-bearing scavengers at three air-fuel ratios, at pressures of 5 and 30 atm., and at temperatures of 350°, 1,000°, 1,800°, and 2,000° K. The air-fuel weight ratio has the values 12, 15:12, and 18. The concentration of PbEt4, M, in milliliters per gallon of iso-octane, has the value 1 or 3. The word "case" is used to designate the halogen concentration. Three cases have been considered [ ]

Jan 1, 1953

By John C. Feeley

The methods used and the funds available for the development and oper- ation of shall mines and the reopening of small abandoned mines frequently present problems that tax the ingenuity and resourcefulness of the mining engineer far beyond that required in the mass production from large deposits. The objective of this paper is to describe in considerable detail the means whereby engineers have solved local problems in reopening an abandoned mine at which equipment, facilities, and funds were limited... The Etowah Coal & Iron Co. Gadsden red-iron-ore mine at Gadsden, Ala., 18 of interest in this category since it is the only independent red-ore mine under active development in the State. All other red-ore mines in Alabama are owned or controlled by the large iron or steel companies. The The mine, located on the southwest end of Shinbone Ridge in the outskirts of Gadsden lies in an ares once productive. but now idle, for many years. ore is relatively highgrade compared with that in the Birmingham area, but the bed is thin and somewhat lenticular. The presence of a large blast furnace at Alabama City, 3 miles from Gadsden, and the growing scarcity of red-iron ore supplies for it offered inducements for reopening the mine in 1946. Up to the time this circular was prepared (1947) only a small quantity of ore (about 1,500 tons) has been produced and shipped to the furnace. A force of 14 men was employed in sinking the main slope and developing a third "lift" (a local term for level) 100 feet below the old mine workings.

May 1, 1949

By M. Clair Smith

This report is one of a series describing exploration, development, mining methods, and costs at United States open-pit mines; the Bureau of Mines prepares and publishes them in cooperation with the mining companies. Their purpose is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods and practices at various United States mines. The exploration, development, equipment, and mining of a large, oxidized-copper ore deposit by open-pit methods, the leaching of the ore with sulfuric acid solution, and the recovery of the copper as cement copper are described herein.

Jan 1, 1958

By D. Randolph Berry

The U.S. Bureau of Mines awarded a contract to Foster-Miller Associates, Inc. (FMA) to provide recommendations on the safest, most practical methods for complying with new regulations requiring that all underground coal miners have a self-contained, self-rescuer (SCSR) -a device capable of supplying, in an emergency, 1 hr of self-contained oxygen (no breathing of mine air). This report develops information and recommendations which could be used during the early stages of nationwide compliance, especially in the areas of inspection, testing, and underground storage of SCSRs. Volume I contains an Executive Summary, Introduction, Definitions, Recommended Guidelines for District Managers and Mine Operators, and a Storage Plan Checklist and Sample Form.

Jan 1, 1981

By Sidney Katell

This report, covering the period January 1965 through December 1965, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the seventh in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are From the following sources:

Jan 1, 1966

By R. L. Bolmer

Rapid depletion of our known mineral resources has stimulated exploration for new mineral deposit. Abandoned mines or prospects may prove to be commercial in today's economy. Often it is necessary to revaluate such properties. Some of these may be inaccessible because of caving of flooding. Many, however, remain in good condition, except that over the years the air in the workings has become depleted of oxygen. Each year the Bureau of Mines receives numerous requests for aid in entering old mines, the air in which is incapable of supporting life. Requests of many individuals who wish to examine or explore-such places with the help, of the Bureau's self-contained oxygen breathing apparatus have been denied because of the hazards involved in the use of this equipment for such purposes. The distance to be traveled in irrespirable gases may be too great for safety; under favorable conditions, a round trip of 2,000 feet from fresh air is the maximum distance that may be traveled.3/ The use of such equipment is hazardous unless a team of at least 5 men thoroughly experienced in its use is provided; and when extensive traveling from. a fresh-air base is required, a reserve team should be provided.3/ Usually, the apparatus is requested for use in exploring workings having only one surface connection, as mines having more than one opening usually are more easily ventilated;,and in some natural ventilation is sufficient or can be made so by cleaning out obstructed openings.

Jan 1, 1951

By Raymond B. Lucas

"Distinction between Tripoli and Diatomaceous EarthMuch confusion exists both in the literature and in the trade as to the proper use of the terms tripoli, tripolite diatomeceons or infusoriai earth, and kieseigunr. All of these terms are often used synonymously by the trade and even in mineralogists and other reference books. Actually, tripoli is a ma- is a material of definite and distinct physical and chemical properties and all of the other terms belong to a different material with just as definite and distinct properties.Originally the term tripolite (loosely called tripole) was given to a diatomaceous cart from Tripoli in Northern Africa. Dena (J.D. Dana, A System of Mineralogy 6th Ed.) calls this material tripolite and gives no authority for the use of the terms tripoli. Between 1880 and 1890 the deposits near Missouri, were opened and the material placed on the market as ""Tripoli"" no doubt due to its resemblance in some respect to the original tripolite or diatomaceous worth from Tripoli. Since that time the term tripoli has with increasing definitenesss been reserved for the Seneca material and other siliceous of similar origin and physical properties, while all siliceous material of organic origin, containing dilators, has been called diatomaceous earth (or its synonyms infusorial earth, kiselguhr, etc.). Rottenstone is sometimes classed with tripoli."

Nov 1, 1920

By B. D. Nash

The Bureau of Mines continued its research into the recovery of fluorine by the phosphoric acid acidulation defluorination of phosphate rock concentrates. A small process development unit with a capacity of about 10 kilo-grams of charge per hour was operated, and concentrates from both Idaho and Florida were processed. Over 80 percent of the fluorine was evolved and recovered as a dilute fluosilicic acid solution. Phosphate extraction from the concentrates always exceeded 98 percent. The fluorine was converted to a synthetic fluorspar product (3CaFa?SiOa) suitable for use as a slag conditioner in electric furnace steelmaking operations.

Jan 1, 1977

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex3 X-ray instrument for the measurement of the ash content of washed bituminous coal products. The results obtained for selected products from six preparation plants in the Appalachian region and one preparation plant in the mid-western region are described. Emphasis of the study was placed on low-ash bituminous coal products suitable for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by ash determination using the Cendrex for all products tested.

Jan 1, 1968

By W. E. Cooper

The International Intercalibration and Intercomparison Program (HIP), consisting of several selected laboratories from four countries, held a radon progeny intercomparison measurement at the U.S. Bureau of Mines experimental Twilight Mine on September 12-14, 1988. Grab samples were taken at four different conditions of low and high radon progeny and condensation nuclei concentrations, respectively. The results showed good agreement among all seven participants. The coefficient of variation of all measurements was 4.7%; after minor corrections for flows and some systematic biases, it was reduced to 3.2%.

Jan 1, 1990

By F. G. Horino

The Bureau of Mines conducted compressive strength tests on model pillars of selected rock types with each pillar containing a critically oriented plane of weakness. The objective of these tests was to determine if a significant increase in the strength of the model pillar could be obtained by either (1) installing tensioned rock bolts through the pillar and normal to the plane of weakness, or (2) wrapping tensioned steel wire ropes around the pillar at uniformly spaced intervals along the pillar. Equations based on Coulomb's failure criterion are developed to predict uniaxial compressive strength of model pillars that are either rock-bolted or wire-roped. Laboratory compressive strength tests on unbolted and bolted model pillars of sandstone, marble, Indiana limestone, and oil shale containing a plane of weakness oriented at 45° showed that the bolted pillars are stronger than the unbolted pillars by 84, 31, 52, and 28 pct, respectively. Laboratory compres-sive strength tests on nonroped and roped model pillars of Texas limestone, sandstone, and granite containing planes of weakness showed that the roped pillars were stronger than the nonroped pillars by factors ranging from 1.01 to 2.41, depending upon the angle of the plane of weakness and the rock type. Rocks with a low Young's modulus benefited most by the wire-roping technique.

Jan 1, 1971

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By Steven R. Ruggieri

This report documents the work performed and the results obtained during the field demonstration of the Remote Sealing System at the USBM's Jenny Mine near Inez, KY in the Fall of 1978. Although various portions of the Remote Sealing System had been used on a number of prior occasions, the field demonstration at Jenny Mine marked the first use of the complete upgraded system including the use of the inert gas generating system for seal placement and the first application of the new froth foam system. The objective of the field demonstration at Jenny Mine was to demonstrate the complete system by emplacing and evaluating several complete underground seals under conditions representing those of a mine fire situation. Several critical sealing conditions were identified including: ? High entry airflow ? Standing water (1 to 2 ft) in the entry ? Flowing water (150 gal/min) ? Irregular roof ? Sealing a 4-way intersection. Four seals were successfully placed under the conditions mentioned above. The demonstration served to verify proposed techniques to handle these conditions as well as to dispel any doubts about the system's capabilities. As a result of the successful field demonstration, the Remote Sealing Equipment is now under the jurisdiction of MSHA's Mine Emergency Operation ready for a mine fire emergency.

Jan 1, 1980

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the 'Y'; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974

By L. C. IlsLey

In January, 1922, a conference relative to trailing cables for use with permissible mining machines was held at the Pittsburgh Experiment Station of the U. S. Bureau of Mines. At this conference it was recommended that the bureau take steps to investigate the rubber-sheathed type of cables and to bring about the establishment of a list of approved cables. Effective until such time as a complete investigation could be made, the bureau asked the several manufacturers holding approvals for mining machines to recommend cables for use with their machines. In general the cables recommended were tentatively approved. Due to the lack of available personnel, no actual tests of cables were made until mid-1927. Meanwhile a field investigation of trailing cables was made at 20 mines of three coal companies in western Pennsylvania, and samples of cables were obtained from the manufacturers for laboratory tests. Twenty-five samples of the concentric-type cable, representing the product of five manufacturers, were obtained for the tests. These cables were of four sizes, as follows: 3 cables of No. 2 B & S gage, 17 cables of No. 3 B & S gage, 3 cables of No. 4 B & S gage, and 2 cables of No. 6 B & S gage.

Jan 1, 1929

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By R. Michael Digman

Few efforts have been undertaken to date to assess the quality of mandated coal mine health and safety training for new miners and for experienced miners. This study was concerned with the quality and effectiveness of existing classroom health and safety training programs. The study involved field data collection through pre- and posttesting of trainees, audio-taping class sessions, and administering short feedback forms with trainers and trainees at 14 sites in West Virginia, Maryland, Kentucky, and Pennsylvania. Results indicate that goals, methods, materials, and outcomes of existing training programs vary widely among trainers and sites. The report provides less by way of solution to problems, than it highlights the breadth of issues that relate to the question of training effectiveness and quality. The report concludes that additional work by industry, labor, government, and academia is necessary in order to improve health and safety training programs. Recommended steps are: (a) to develop performance standards and measurable criteria in each of the types of mandated training, (b) to develop better training of trainers, (c) to develop expanded training support services. and (d) to undertake further research and development in health and safety training in the mining industry

Jan 1, 1982

By J. A. Herdlick

The Star mine, near Neihart, Cascade County, Mont., has been in continuous operation since the construction of a 50-ton bulk flotation mill in 1939. The mine was examined by G. N. Bennett, an engineer of the Bureau of Mines, in November 1942. At that time the life of the operation appeared to be limited and a program of crosscutting and core drilling were recommended. The program had as its objective the investigation of a promising undeveloped area lying west of the Star vein and, if possible, the development of enough reserves in this area to insure continuous operation during the war emergency. Development of additional reserves would then justify necessary changes in the mill in order to eliminate the heavy penalties imposed for excess zinc in the bulk concentrates. The Bureau of Mines work began in February 1944 and was completed in September 1944. The project was started by Wilder R. Brinton and continued by Thomas W. Oster, mining engineers in the Bureau's Montana district office. Beneficiation tests on are and concentrates were made after completion of the underground work. This report presents the factual data obtained during all phases of the Bureau's investigation.

Jan 1, 1949

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935