Search Documents

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first paper5/ dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second dealt with extraction in a mine (Crucible) in which coal was loaded. by hand and in which the rib lines wore long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central hart of Washington County, Pa. , approximately midway between the Montour 10 end Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalizations as appear to be justified.

Jan 1, 1940

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By R. H. Hiltz

The Coal Mine Health and Safety Act of 1969 legislated maximum dust levels for the working place. As the law was implemented, extensive efforts were undertaken to provide the technology necessary to control dust generation. One approach to dust control was the use of high expansion foam in place of the usual water sprays on coal cutting equipment. At the time of the act, high expansion foam had already seen considerable testing for the suppression of dust in underground coal mines. Work by MSA, several coal companies and the Bureau of Mines itself had provided data which showed foam to have some merit as a dust control mechanism. It suffered in a few areas, however, which limited its practical application. Its principal difficulty was persistence which hampered operations due to foam buildup, but problems were also encountered due to equipment size and form.

Jan 1, 1975

By R. H. Lien

The Bureau of Mines has conducted research on a flue gas desulfurization (FGD) process as part of its goal of minimizing the undesirable environmental impacts associated with sulfur dioxide (S02)-bearing waste gases. This FGD process, referred to as the modified citrate process, involves absorption of S02 in a buffered citric acid solution. The absorbed S02 is subsequently stripped from the solution using steam, which regenerates the solution and produces a wet S02 product. This product can be further processed to make sulfuric acid or liquid S02. Economic evaluations showed the process to be expensive when the stripper was operated at or near ambient pressures because of the large amounts of steam required for solution regeneration. Research was directed at reducing steam consumption in the stripper. The effect of stripper pressure on steam consumption was investigated. A process research unit (PRU) was operated with the stripper pressurized in the range of 5 to 150 psig. Test results showed that steam consumption decreased with increased stripper pressure. For example, when operating the PRU stripper at 150 psig, 4.1 grams of steam per gram of S02 was required to remove 90 pct of the S02 from a 1.0-vol-pct-S02 gas. This compares to 7.1 grams of steam per gram of S02 required for 90-pct S02 recovery at 5 psig.

Jan 1, 1982

By B. J. Barfield

Standard erosion plots (4.6 m by 22.1 m on 9 percent slope) were constructed on the Alston Surface Mine of Peabody Coal Company in Western Kentucky to evaluate the effects of placement technique and density on the erodibility and eroded size distribution from mine spoil and reconstructed topsoil. PLots were constructed with a dozer and scraper pan from shale spoil material, topsoil (A horizon) and subsoil (B and C horizon mixture) using soils stockpiled at the Alston Surface Mine. Plots were evaluated under fallow conditions with a tilled plot surface and two compacted conditions. One compacted condition was generated by tracking the surface with a dozer and rolling with a loaded scraper pan. The second was generated by rolling the surface with a solid wheel compactor. Rainfall was supplied with the Kentucky Rainfall Simulator at a rate of 63.5 mm h-l with the plots in three different soil moisture conditions; dry, field capacity, and very wet. Runoff was evaluated for flow rates, sediment concentrations, and aggregate and primary particle size distributions. Sediment yields and the Universal Soil Loss Equation E130 indexes were calculated from the data for each plot. The erodibility was calculated from the tilled plot data using a weighted soil loss and E130 value from the dry, field capacity and wet runs, and a cover management factor calculated for every other condition. For the topsoil and subsoil plots, sediment yield was greatest for the dozer scraper pan plots and lowest for the tilled plots. For the shale plots, erosion rates from the wheeled compacter plots were the highest and tilled plots the lowest. Average erodibilities were 0.14, 0.38, and 0.41 tons ac h ft-1 tonf-1 in-1 hundred ac-1 for the shale, subsoil, and top-soil plots. Cover management factors for each plot were 1.29, 1.42, and 1.17 for shale, topsoil and subsoil plots compacted with the solid wheeled compacter and 1.29, 3.79, and 2.51 for shale, subsoil, and topsoil plots compacted with the dozer scraper pan conbination. The accuracy of the Wischmeier erodibility nomograph was evaluated on the data collected. Erodibilities were accurately predicted for the topsoil plot and poorly predicted for the sub-soil plot. The accuracy of the CREAMS procedures for predicting the composition (size distribution) of eroded particles was also evaluated. The composition was well predicted for the topsoil plots, moderately well predicted for the shale plots and poorly predicted for the subsoil plots.

Jan 1, 1983

By J. C. Dumbrille

The following account of wining practices of the Kirkland Late Gold twining Co., (Ltd.), at Kirkland Lake, Ontario, is one of 4 series of papers being prepared by the United States Bureau of Mines on mining practices, methods, sad costs in various districts. The author has prepared this paper with the help and permission of J. B. Tyrrell and W. M. Sixt, the managing director and the mine manager, respectively. This mine is operating at a daily rate of about 150 tons.

Jan 1, 1931

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmosphere .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By J. I. Paige

As part of a continuing effort to develop technology that maximizes mineral and metal recovery from domestic resources, the Bureau of Mines investigated a method to totally utilize copper converter slags without recycling them back through the matte smelting furnace. The research was directed toward (1) recovering the contained copper in converting slags by producing a recyclable copper-iron matte, (2) carbothermically reducing the slags to recover the iron, and (3) producing slag wool from the depleted slags. This report deals with the reduction of three industrial converting slags, containing 2.0 to 7.3 wt-pct Cu, in an 800-kVA electric arc furnace to produce a recyclable copper-iron matte. The addition of sufficient iron pyrite to provide 29 to 113 pct of the stoichiometric sulfur (based on producing 40-pct-Cu matte) produced a recyclable matte (36 to 61 pct Cu) at an energy consumption of 520 to 700 kWh per ton of solid material charged. The expected energy saving for treating molten slag in an electric furnace (5-to 9-MVA range) is about 400 kWh per ton of molten slag treated.

Jan 1, 1982

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmospheres .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By J. W. Thompson

Be if enacted by the Senate and House of Representatives of the United States of America in Congress assembled, That deposits of coal, phosphate, sodium, oil, oil shale, or gas, and lands containing such deposits owned by the United States, including those in national forests, but excluding lands acquired under the Act known as the Appalachian Forest Act, approved March 1, 1911 (Thirty-sixth Statutes, page 9G1), and those in national parks, and in lands Withdrawn or reserved for military or naval uses or purposes, except as heroinafter provided, shall be subject to disposition in the form and manner provided by this Act to citizens of the United States, or to any association of such persons, or to any corporation organized under the laws of the United States, or of ;iny State or Territory thereof, and in the case of coal, oil, oil shale, or gas, to municipalities: Provided, That the United States reserves the right to extract helium from all gas produced from lands permitted, leased, or other- wise granted under the provisions of this Act, under such rules and regulations as shall be prescribed by the Secretary of the Interior: Provided further, That in the extraction of helium from gas produced from such lands, it shall be so extracted as to cause no substantial delay in the delivery of gas produced from the well to the purchaser thereof: And provided further, That citizens of another country, the laws, customs, or regulations of which, deny similar or like privileges to citizens or corporations of this country, shall not by stock ownership, stock holding, or stock control, own any interest in any lease acquired under the provisions of this Act.

Jan 1, 1921

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By William O. Vanderburg

This report 3/gives the results of a reconnaissance of the mining districts in Lander County, Nev., made from March 29 to April 20 and from May 9 to May 21, 1938, during which virtually all of the mining districts n the county were visited. No attempt has been made to include in this report all the mines and prospects in the various mining districts, and it should be stated that whether or not a property is mentioned herein has no. bearing on its merits. The report rovers the situation of the various districts, types of ore deposits, ownership and description of mines and prospects, information on past and current activity, and other information of economic interest likely to be useful to those interested in the development of our mineral resources. The names of the various districts mentioned are those generally used when they were organized for purposes of record and regulation. When originally organized, the districts embraced large areas with no well-defined boundaries, so that the names have little geographical significance.

Jan 1, 1939

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956

By Doris M. Hyde

The economy of Belize continued to show a very slight but still positive growth during 1986. The gross domestic product (GDP) was estimated to have been about $164 million,2 almost the same as those of 1984 and 1985. Foreign investors looked favorably on Belize because it had remained isolated from the sometimes turbulent political and social strife elsewhere in Central America. Reportedly, in late 1986, Guatemala had decided not to pursue its claim to Belizean territory and to give full recognition to that country. Discussions were to be held regarding any matters of mutual concern. New investment possibilities were oriented toward agriculture or manufacturing endeavors. Except for some interest in petroleum exploration, the minerals sector remained limited to the quarrying of construction-related materials.

Jan 1, 1988

By E. H. Burroughs

HISTORICAL REFERENCES OCCURRENCE-GEOLOGY AND ORIGIN. 4. ARNOLD, RALPH. Conservation of the oil and gas resources of the Americas, Econ. Geol., vol. 11, Apr.-May, 1916, pp. 203-222; June, 1916, pp. 299-326; Proc. 2nd Pan American Sci. Cong., 1915-1916, vol. 3, Conservation of natural resources, pp. 207-237. Shows occurrence of oll, and status and possibilities of oil Industry in each country. Discusses briefly ways in which oll reserves may be conserved. 5. RUTIS, A. A. Petroleum known since remote times. Oil and Gas Jour., vol. 15, Nov. 2, 1916, pp. 33, 37. Gives historical reférences to the use of petroleum from Bible times to its discovery In America. See also Nos. 3, 257, 202, 337, 1843.

Jan 1, 1919

By Virgil J. Stachura

The Bureau of Mines has investigated techniques and instrumentation that measure accurately the airblast overpressures from surface mine blasting. The results include equivalencies between broadband research instrumentation and commercially available impulse precision sound levels meters measuring: root-mean-square, peak, fast, slow, impulse, A and C weighting, C-weighted sound exposure level (CSEL), and "linear" (flat) response. These values were obtained from field measurements and broadband FM tape recordings of production blasts at area and contour coal mines, limestones quarries, and iron mines. Frequency response was determined for 14 commercial systems.

Jan 1, 1981

By David C. Oyler, Hakan Gurgenli, Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.