Search Documents

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By Kinross Paracatu, Victor Morais, Luis Marinho, Rolando Fuentes, Lucas Steffen, Leopoldo Muñoz, Washington Vilas

Nowadays, mining operations close to communities face increasingly challenges, especially in their drilling and blasting operations. One of the critical effects are the ground vibrations produced in its surroundings. The impact on the community must be minimized to guarantee the license to operate and, on the other hand, costs must be optimized, and an adequate fragmentation must be achieved to ensure the efficiency of subsequent processes and, consequently, to give sustainability to the business. In this regard, it is necessary that some controlled blasting technique to be performed and the utilization of advanced vibrations models. Currently, it is common in the industry either use of the double decking technique, where very low explosive charges are applied, making it necessary to use smaller drill patterns in order to keep powder factor as per design, which strongly increases the demand for drilling and a consequent impact negative on costs.

Feb 6, 2023

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By Hideaki Kitajima, Daisuke Fukuda, Kazuma Moriya, Katsuya Sasaki, Katsuhiko Kaneko

The purpose of this research is to analyze the fracture process and achieve design optimization of a splitting method for concrete and rocks termed the electric discharge impulse crushing method (EDICM). The EDICM utilizes the cartridges being set in boreholes in the splitting target. The cartridge has a thin metal wire and is filled with nitromethane. By applying the electric discharge to the wire in the cartridge, plasma is caused leading to the vaporization of the wire. Then the deflagration of the nitromethane commences, which generates borehole pressure for splitting the target. Although the required splitting time is roughly several hundred micro-seconds and much slower than ordinary blasting, the fracturing still completes in quite short time and understanding the fracture process of opaque and brittle materials such as rock and concrete in this time scale is of academic importance.

Jan 1, 2011

By Jeffrey E. Loney, Andrew F. McKnown

Recovery of contaminated groundwater migrating through bedrock can be very difficult due to the low transmissivity of many bedrock fracture systems. To overcome these difficulties, a system of controlled "trench" blasting has been used on several projects to assist in cutting off and collecting groundwater plumes in bedrock. By using a combination of trench blasting and presplitting techniques, linear "fracture" zones are created in appropriate locations to significantly increase flow into recovery wells and control plume migration.

Jan 1, 1995

By Courtney W. Shea, Dennis Clark

Reckless blasting can have tragic consequences: The death of an innocent traveler, the financial demise of a coal company, and even criminal prosecution. In June 1993, a Tennessee coal mining company was blasting to loosen overburden at its surface mine. The mine was located immediately adjacent to the right-of-way of the northbound lane of Interstate 75. The approved permit included special precautions to be taken when blasting in the area closest to the interstate, including monitoring traffic so as to blast when the northbound lane was clear.

Jan 1, 1998

By R Deshaise, B Mbhanty

The importance of controlling density of commercial explosives, and the various means to achieve it are described. m e field conditions responsible for density changes during blasting and their effect on blast results are examined. Understanding of the behaviour of density control ingredients such as gas bubbles, glass and plastic microballoons under pressure, is considered essential to predicting explosives performance. Both static and dynamic pressure effects have been studied for typical donor-receptor cartridge configurations. The amplitude and temporal characteristics of dynamic pressures inside receptor explosives have been studied by means of the underwater test, and guidelines developed to limit density changes due to external pressures.

Jan 1, 1989

By Ian A. Niell, Alastair C. Torrance

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation velocities of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation measurement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 1509. However, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1990

By William Everett, Jack Eloranta

United Taconite is an iron ore mine operated by Cleveland-Cliffs Inc (Cliffs) located near Eveleth, Minnesota. The mine, originally known as Eveleth Taconite Mines, was purchased in December 2003 by Cliffs (70%) and Laiwu Steel (30%). The mine site, known as the Thunderbird Mine, produces taconite ore for delivery by rail to the company’s Fairlane plant, located approximately 10 miles to the south near Forbes, Minnesota. At the plant, the crude ore is ground, concentrated and processed into pellets for steel industry customers. Total pellet production capacity is about 5.4 million long tons (Ltons) per year.

Jan 1, 2006

By Robert B. Hopler

Hercules Incorporated has developed and introduced a totally new non-electric delay blasting cap system which utilizes a low energy gas detonation to activate the caps. Unlike any other initiation system, there is no hole-to-hole connection other than empty plastic tubing until the blast is to be set off. Only at that time, when all personnel and equipment are in the clear, is the special gas mixture introduced through the tubing. The actual time of firing is completely under the control of the operator, by pressing the fire button on the blasting machine.

Jan 1, 1977

By Brendan O'Reilly, Outokumpu Zinc, Geoff J. Johnston, S Durucan

Historically vibration monitoring has dealt primarily with surface blasting or "near field" monitoring of underground blasts. The Situation at Tara Mines is different, blasting occurs up to 400m underground, with a number of blasts occurring daily and occasionally with residential properties directly above the blasting site. Tara Mines, due to both its location (1.5 km from the rural town of Navan) and stringent planning conditions have always had to monitor, carefully plan and control the levels of vibration from blasting. The statutory vibration limit at Tara allows a maximum peak particle velocity of 7.62 mm/s with no frequency limitations. Levels of vibration have been monitored continuously since mining operations began in 1972.

Jan 1, 1994

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By M. K. Ameen, R. El-Hacha

This paper presents the analytical results obtained from numerical simulation of reinforced concrete slabs strengthened with various FRP systems and subjected to blast loading. A three-dimensional finite element model using AUTODYN software was used to predict the overall behavior of the slabs. The numerical results were validated by comparing with experimental results from a program carried out to investigate the efficiency of different strengthening systems on the blast resistance improvement of small-scale reinforced concrete (RC) slabs. The experimental program consisted of testing nine RC slabs strengthened with three different externally bonded (EB) FRP systems attached at the bottom side of the slabs and one RC slab tested without strengthening for comparison purposes. The EB FRP strengthening systems investigated included two layers of Carbon Fiber Reinforced Polymer (CFRP) sheets, two layers of Glass Fiber Reinforced Polymer (GFRP) sheets, and one layer of Glass-Fiber Resin Polymer (GRP) sheet. Different epoxy resin, patching mortars and impregnating epoxy adhesives were used for the slab surface preparation and FRP system application of the strengthening layers. The aim was to evaluate the residual strength of the test specimens after exposure to blast loads. The blast loading parameters were evaluated for each test using AUTODYN simulation and compared with the computer program CONWEP. All specimens were subjected to same spherical TNT charge weight and stand-off distance with the respect to the slab top surface. Extensive comparison is made between the experimental results and the AUTODYN simulations for the control unstrengthened slab and the strengthened slabs including time history records of the bottom steel strain and mid-span acceleration and the peak dynamic deflection of the slabs.

Jan 1, 2010

By Karl Peterson, Bibhu Mohanty, Chanakya Nariseti

The mechanism of crack formation in two target rocks (Kuru granite and Flamboro Limestone) is studied experimentally by simulating the impact action of a percussive drilling bit. Rock samples are dynamically loaded using a custom made impacting bit (8 mm, 12 mm and 15 mm diameter bits). The target rocks are impacted at velocities 8, 10, and 12 m/s. The resulting crack patterns are visualized by three techniques, Dye penetration, CAT scans and Optical scans. Mapping of the crack patterns is manually done with Photoshop. For 3D damage visualization, the crack patterns are mapped in two planes (impact surface and longitudinal sections). The three techniques are compared to determine an optimum technique for better damage visualization. The evolution of crack pattern with impact velocity and bit diameter is discussed.

Jan 1, 2015

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines fired seven test blasts in a 22-ft bench of limestone, screening the material to investigate the influence of explosive type and between row delays on fragmentation. Four 4-hole, single-row test shots were conducted evaluating dynamite, ANFO, emulsion, and a 60-40 emulsion-ANFO mix. Three 12-hole shots, with three rows of 4-holes, evaluated delays between rows of 24, 36, and 120 ms. Accurate in-hole electronic delays were used, firing within 1.5-ms of the nominal delay. All seven shots had a 6- to 7-ft burden, 10-ft spacing, with a hole diameter of 3-1/2 in fired on a 12-ms delay between holes in the row. The tests were instrumented with strain gauges grouted in the burden region examining stress wave and gas pressure effects. Fiber optic probes were used to confirm timing and to obtain detonation velocities.

Jan 1, 1989

By Rajesh Sonkar, Sanjeev Kumar

The deployment of Dragline machines in opencast coal projects involves huge capital expenditure as well as operating costs. The mine operators always endeavor to ensure smooth excavation of material by the Dragline machines while meeting the major objectives of safety, minimal disturbance to environment and optimal operating costs. Optimization of fragmentation through well designed blasts is fundamental in meeting part of the objectives is good fragmentation of rock or mineral proposed to be lifted by the Dragline machine. If the overburden lying over mineral is not properly fragmented, it may result in formation of ‘Toe’ the removal of which is the most arduous task in opencast coal mines. The mine operators always endeavor to achieve best possible results in blasting to ensure smooth operation of the high cost Dragline Machine. However, despite continuous efforts by the blasting engineers involved in bench blasting for the machine, the formation of ‘Toe’ is an ever nagging problem faced in large opencast coal projects eventually reducing the overall operational efficiency of mining.

Jan 1, 2011

By Ruilin Yang

This paper provides a theoretical analysis of shockwaves in an air-deck induced by detonation of an explosive charge and shows that the initial shock pressure in the air-deck at the interface with the explosive charge is only about 1% of the detonation pressure. A rarefaction wave with the low pressure travels back into the explosion detonation products greatly reducing the post-CJ detonation pressure. Additionally, AUTODYN modelling shows that the pressure attenuates further during shockwave propagation along the air-deck. Although the pressure increases at the bottom of the blasthole due to shock reflection, the overall pressure in an air-deck does not increase and is still around 1% of the detonation pressure which is too low to break most rock.

Jan 1, 2016

By Orica Chile, Orica Brasil, Orica Brasil Victor Morais, Kinross Paracatu Leopoldo Muñoz, Kinross Paracatu Luis Marinho, Gubio Barsottini, Orica Brasil José Vergara, Lucas Steffen, Orica Brasil Washington Vilas

In drill and blast activities, it has been a challenge to sculpt walls accordingly to what has been designed in state-of-art mining design software. Obviously, the perfection of making neat and smooth walls – using aggressive sources of energy, like explosives – are time-and-money consumable and, sometimes, even unnecessary. But undoubtedly, it is vital to guarantee solid walls, safe operations environment, beyond to avoid ore losses and pit constraints caused by poor rock breakage on detonation. Kinross Gold Corporation owns the biggest Brazilian Gold Mine, located in Minas Gerais state. Morro do Ouro mine has reached over 30 years of operation, and due its mature age, the complex has developed its pits, becoming them deeper and surrounded by high walls.

Feb 6, 2023

By L. Muñoz, L. Steffen, J. Alarcón, W. Vilas

Today, mining operations close to communities face increasing challenges, especially in their drilling and blasting operations. Proper management of environmental impacts is important to guarantee their license to operate and to provide sustainability to the mining business in the long term. Blasting is an event that generates impacts such as vibrations, noise (airblast), projections (flyrocks), ejection of dust and fumes (when there is a deficient detonation of the explosive). If any of these variables exceed the established regulations, sanctions can be generated and even lead to stop mining operations. The goal of this work is to present a review of different techniques, concepts, technologies, simulation software and monitoring / control tools to minimize the environmental impact generated by blasting. For which, a case study of a big scale open pit mine in Brazil with operations close to a community will be presented. An adequate management model, combined with good operational practices, the use of new technologies, enable a safe operation without incidents with the communities. In this way, building trust with neighbours, maintaining the license to operate, and helping mining industry to mobilize resources essential for progress in a sustainable way

Jan 1, 2024

By Thad M. Jones

This paper considers the sampling, digitizing and reconstruction of seismic signals. A sampling frequency range is proposed and a minimum limit is suggested. Digitizing precision criteria for both peak velocity and analysis applications are given. Several methods for reconstructing signals from sampled data are presented.

Jan 1, 1985