Search Documents

By Rakesh Raghavaraju, Bibhu Mohanty

The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

Feb 1, 2020

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed.

Feb 1, 2020

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

By Rakesh Raghavaraju, Bibhu Mohanty

Prediction of fracture and fragmentation characteristics of a rock mass subjected to dynamic loads, such as in blasting remains a major technical challenge. The present study is aimed at characterizing the shock transmission properties in controlled experiments in small scale in a well-characterized granitic rock, under varying borehole coupling conditions. Single blast-hole tests were conducted in a granitic rock sample of 145 mm (5.7 inches) diameter and height. The boreholes (in two diameters: 6.4 mm (1/4 inch) or 9.5 mm (3/8 inch)) were loaded with detonating cord of varying charge weight (5.3 g/m or 25 grains/ft to 31.8 g/m or 150 grains/ft of PETN). The effect of explosion gas penetration into the target rock was eliminated by inserting a thin-walled copper liner along the borehole wall. Embedded carbon composite resisters were employed at varying distances from the borehole to measure transmitted shock pressure for two coupling conditions (i.e. air and water) at distances of 1x to 9x the borehole diameter. The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

By Paul L. Matrin

This paper will discuss the recent and on-going drill and blast optimization measures at the Sparkhule Limestone Quarry, which have resulted in a 44% reduction of drill and blast unit costs per ton of broken limestone. This amounts to approximately $240,000 of drill and blast saving per year at current annual production rates of about 2.5 million tons (2.3 million tonnes) total material shot. The reduction of drill and blast costs were accomplished by a detailed and controlled in-the-mine drill/blast experimentation and cost evaluation using 8 different blast pattern designs and shots totaling approximately 267,000 tons (242,200 tonnes) of shot and mucked material. A careful review of the geology of the deposit was performed to determine the different rock classification/strengths/structural properties and to adjust blast designs to optimize fragmentation for the different rock types. Equipment loading productivity and crusher throughput performance were monitored as part of the evaluation process to assure that an optimal fragmentation of broken rock was achieved with the new blast designs. The study included the review of bulk explosive and accessory selection criteria (ammonia nitrate/fuel oil mix - ANFO, mini prills (high density ANFO), sensitized and un-sensitized emulsions at a 30% emulsion/70% ANFO blend), blast pattern design, charge diameter and the cost of drilling. Laser profiling technology was used to assure proper bench heights, stemming and sub-drill footage and front row burdens. High speed photography, video and still photos were taken of the different designed shots to assist in the evaluation of the performance of each blast. Powder density checks, size distribution, back break, detonation velocity and pressure measurements were taken. Different borehole diameters were used for the drill optimization study and drilling cost and productivities determined. A detailed cost comparison between in-house blasting and complete shot service was prepared to evaluate if shot service is a cost effective alternative to current in-house loading and blasting including a review of the new and pending United States Bureau of Alcohol, Tobacco and Fire Arms (ATF) regulations and associated owner costs/risks and potential benefit of shot service.

Jan 1, 2004

By Thierry Bernard

Considering rock fragmentation by explosive as the ultimate goal in mines and quarries, vibrations are definitely one of the main drawbacks faced by the Industry. If we can accurately predict vibrations level and frequencies, taking into account the whole set of the involved parameters, this will bring a major benefit to each of us, in our daily production process optimization effort. The model presented in this paper answers to this need thanks to a "holistic" approach of the vibration mechanism. By holistic, we mean that we approach the vibration effect (wave propagation) as a whole, by understanding all of the mechanisms that contributes to the process and comprehending how they are connected.

Jan 1, 2009

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"An Event Tree Analysis (ETA) is an established approach for logically deconstructing and assessing scenarios for probabilistic risk assessment. This deconstruction into a series of understandable eventsfacilitates probability estimation for explicitly defined explosive terrorism scenarios with consideration of modes of possible failure during execution (a scenario is defined through selection of a target, selection of an explosive material, and interdiction prior to arriving at general target location, etc.). Further, each event is decomposed into a range of possible outcomes. The physical action or reality ofthe outcome is statistically represented by “branches” of the event tree (e.g., the terrorist may choose totarget a stadium, hotel, or subway; terrorists may be successful or unsuccessful in acquiring the material)."

Jan 1, 2017

By C. Zuniga, S. Combrinck, C. Peters

Agnico Eagle Gold have partnered with Enaex Australia at their Fosterville gold mine to leverage a combination of drill and blast technologies to optimise underground development mining. The mine is the first site globally to collaboratively develop and trial Enaex SWIFT electronic development detonators, which utilise a novel approach to the user interface, simplifying implementation and enabling the benefits of electronic initiation without the complexity of a conventional system. This has been combined with the use of a Sandvik 422i smart jumbo, and the Enaex underground emulsion charging unit with the capability to tailor the delivery of explosives as required and report on a hole-by-hole basis. The combination of these technologies enables full engineering oversight of the development cycle, in turn enabling optimisation of this process in a historically conservative application. The methodology for leveraging these technologies is to bore a controlled and defined blast pattern through using a smart jumbo, load the blast holes utilising lace loading to deliver a desired quantity of ammonium nitrate emulsion per hole, with the ability to reduce chargeweight for perimeter control, and utilising Enaex SWIFT electronic detonators with flexible template type pre-defined delays to initiate the blast holes. Subsequent to firing and excavation the performance of the blast in fragmentation, advance efficiency, and overbreak and underbreak is measured and reviewed. This is then used to optimise the development cycle and apply to other parts of the mine.

Feb 6, 2023

By Dale S. Preece, Ruilin Yang

"Air-decks are often employed for presplitting along the final highwall of a blast and are sometimes also included at the bottom or in the middle of explosive columns in the production portion of a blast. Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidlyattenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that theresulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of theexplosive."

Jan 1, 2017

By Paulo Couceiro, Manuel Lopez Cano, Carlos Rodgriguez Calvo

Apart from its difficult execution, underwater blasting is one of the most critical operations of the blasting techniques; mainly because of the ground vibrations - normally associated with low frequencies -, destructive hydraulic shock waves, the difficult coordination, and high costs. To solve these challenges during the underwater blasting on the expansion program for the Panama Canal “Widening and Deepening of the Pacific Entrance and the South approach Channel to the Third set of Locks of the Panama Canal”, a new method to blast using bulk explosive, developed by MAXAM, was used. The project was successfully executed, and more than 800.000m3 were blasted in less than 5 months, jointly with the biggest underwater drilling platform ever build, the Yuan Dong 007, with ten hydraulic drills on board guaranteeing a high production, excellent fragmentation result, total control of the vibration levels, no complain of the neighborhood surrounding the area of the project and simple local logistic due to the classification of the main product used (an oxidizer classified as 5.1). That was finally sensitized down in the hole.

Jan 1, 2011

By Jose A. Sanchidrián, Ricardo Castedo, Pablo Segarra, Juan Navarro

A study conducted at a mine site that used traditional field surveying and physical hole spot markings bench marked their combined drill and blast performance. The analysis of the operational expenditure (OPEX) improvement determined there were many measurable cost improvements. A primary factor that most operations have to deal with is over drilling of holes. This alone impacts the cost due to nonproductive labor allocations, excessive explosive costs, increased drill tool costs, increased drilling costs and has an impact on the downstream operation cost such as digging the shot material. Other related investigations also show a downstream impact of poor fragmentation on digging payload tonnes, cycle times, haulage payload tonnes, time to load a truck and the number of passes to load the tuck. The intent of this presentation is to draw attention to aspects of mining we understand but may be missing the big picture effects, such as the ability to reduce the operational expenditures consistently to impact the bottom line. The target audience is across the board from owner operators, drill and blast contractors to blasting contractors. Everyone can benefit from these improvements.

Jan 1, 2019

By Ulrich Leiste

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By D. Preece

The mining and oil industry employs techniques such as geologic mapping, core drilling and electromagnetic and potential field techniques to explore for new deposits. Since new discoveries of major near-surface ore bodies are becoming progressively rare and since traditional exploration methods are unable to resolve ore bodies deeper than about 500m, high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3km.

Jan 1, 2011

By A. S. Tawadrous

Fines are produced in any blasting application. Depending on the application, fines may or may not be a desirable product of the blast. In most quarry and construction applications, fines are considered an undesirable product since it does not constitute a sellable product and there are costs to the operation for disposal. On the other hand, in most open pits fines do not represent as much of a problem since the ore has to be crushed and ground after being blasted. Therefore, fines in such operations may reduce the energy consumed in the downstream operations.

Jan 1, 2012

By C. K. McKenzie

Presents outline of flyrock model and a field procedure to validate predictions of maximum projection distance. Field results are presented from 13 field tests with two different hole diameters.

Feb 1, 2020

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

By R. F. Favreau, Patrice Favreau

In many quarries and construction sites visited by the authors over the last 50 years, the latter have observed muck piles from blasting with explosives, which included numerous large blocks, in some cases of dimensions larger than the input to the crusher. The names of these sites cannot be given in the article because the owners insist that data obtained on such visits be kept confidential. Often the blasters felt that the natural fissures in the rock would compensate for the use of a low powder factor, and they asked the authors to explain why such blocks were present. A detailed analysis of the situation often indicated that the cause of the blocks is that explained by figures such as 6 and 7 below in the article.

Jan 1, 2018

By Hairong Zeng, Shahram Tafazoli, Edmond Chow

Blast fragmentation is one of the main parameters for optimizing mineral processing, but reliable data is difficult to acquire, resulting in unpredictable performance and efficiency. Crusher and grinder circuits are designed to process specific rock size ranges. Oversized rocks require extra energy to reduce before feeding into the process, and undersized rocks indicate that the process is not used to its full extent. Blast design is the key to controlling the blast fragmentation, so the ability to accurately monitor the particle sizes is imperative.

Jan 1, 2011

By J. Eloranta

"Previous work indicated that the annual per-capita consumption of raw aggregate material averages about 10 tons; half of which is produced by blasting. Given a population of approximately 320 million in the United States alone, this amounts to 1.6 billion tons of blasted material annually. It was also estimated that up to 20% of the blasted material in aggregate operations is smaller than 6.35 mm (1/4inch) in size. Thus, about 320 million tons (i.e. 1 ton per capita) of byproduct is produced annually and sold at significantly lower prices or potentially discarded in waste dumps."

Jan 1, 2017