Search Documents

By Edward J. Jr Walter, Edward J. Walter

The vibration problem is approximately fifty years old. The original investigation of the U.S. Bureau of Mines was begun in 1930. Significant investigation into the problem was done by Crandell, Langefors, et al, Edwards and Northwood, and again by the Bureau of Mines. This resulted in an effective Safe Limit standard expressed in particle velocity as 2.0 inches per second.

Jan 1, 1979

By Paul Schmiesing, Matt Higgins

Central Oregon is a fast growing resort community centered in Bend, Oregon. Bend is bordered by the Cascade Mountains to the west and the high dessert to the east. Central Oregon is blanketed with lava rock with little topsoil. Ditch blasting is a staple in the area. Almost all utilities excavation (gas lines, sewer lines, water lines, and electrical lines) requires blasting. There is also a considerable amount of blasting required for site excavations and drywells. On average, there are over 500 blasts per year in Bend alone. All of this blasting is done using small holes, generally 2.5 inches in diameter. Typical ditches will have 200 holes, between 2-3 rows wide, with an average depth of 8 feet, and on 36 inch centers. Almost all shots are dry. Successful blasting requires careful control of drilling and loading. The vesicular basalt contains numerous lava tubes and caves making drilling and loading difficult. The rock conditions vary greatly from one side of town to the other requiring different powder factors and different scale of distances for vibration control. Caret%1 calculations of vibration predictions and use of site-specific seismic info is necessary. Marry shots will require deck loading and careful timing to ensure one-charge per delay. It is an every day occurrence to be blasting near residential and commercial structures or high pressure gas lines. Many times ditch blasting will incorporate excavation blasting. The different hole patterns used for the ditches and the excavation shots presents challenging timing sequences.

Jan 1, 2000

By Michael S. Wieland

This report discusses measurement techniques utilized in and trend results obtained from research on delay blasting malfunctions in underground coal shots at the U.S. Bureau of Mines. Charge malfunctions occur during delay blasting in underground or surface mines, rendering the explosive operations more hazardous and less productive. Modern instrumentation techniques reveal several types of reduced charge performance, resulting from cross-hole interactions. Two receptor (wave-target) charge malfunctions were detected in fourteen shots that were undeniable. There were other receptor charges that exhibited under-performance by registering out-of-tolerance or noticeably reduced detonation rates. Delay blasting generates tremendous shock waves and rifting forces that fracture and heave the surrounding stratum and unfortunately damage remaining unfired charges. This report contains two graphs, representing roughly 1% of total records, that show donor (wave-source) charge shock waves and rift (reaction-to-heave) compressions. These debilitating wave impacts precipitate modes of reduced charge performance ranging from weak detonations or misfires to sympathetic detonations. As recognized from previous research, impaired charges react poorly, perform less useful work, and yield fumes with atypical higher toxicity.

Jan 1, 1995

By James Goldberg, Sally Zadra, Wiliam Reisz

Early recognition and risk assessment is critical to sustaining a safe and productive blasting operation. While every blasting environment holds inherent risk, highwall blasting in highly congested areas such as Hanson Material Service Corporation’s Romeoville and Thornton quarries in the greater south Chicago metropolitan area can be particularly perilous

Jan 1, 2008

By Rafael Tadeu Pinto e Moura, Giorgio De Tomi, Jacopo Seccatore

This paper describes a research and development project in an open-cast mine with the goal to achieve an average P80 of 300 mm (11,8”) in the run-of-mine (ROM) product without altering the existing budget. The project included several variables in the blast design that were not previously taken into account, such as the orientation of natural joint sets in the rock mass, specific energy of the explosive and firing sequence. The new blast design method considered the directions of natural joint sets and determined the drilling pattern and the firing sequence accordingly to favor the movement of the blasted rock along its preferential direction, to reduce its confinement. At the end of the project, it was achieved an average P80 of 304 mm (12”) in the ROM, 50% lower than the one at the beginning of the project. The final blast of the project showed a reduction of 3% of the drill and blast cost, employing the same powder factor and the same drill pattern size used at the beginning of the project. The results achieved show how rock fragmentation is related to variables that are not contemplated in the most common fragmentation models: the firing sequence and the direction of movement in the blast.

Jan 1, 2015

By Joshua Hoffman, Braden Lusk, Perry Kyle

With the advent of any new technology comes the necessity of fully understanding the mechanics of that technology. The Shock Tunnel is one such technology that provides a cost effective means of simulating large-scale explosions while requiring a fraction of the explosive and space. Although the technique is known and practiced, the dynamics and mechanics of this technology has yet to be fully understood. A relationship between the energy potential of a given explosive and the energy realized at a set of distances was determined. This data was then compared to the energies realized from the same explosive when utilized in conjunction with a shock tunnel. A relationship between potential and realized energy outputs from explosive based shock tunnels exists and the understanding of this relationship would allow all for predictions to be made to forecast a specific amount of explosive required to produce a desired energy output. This energy output should then be relatable to peak pressures produced via the shock tunnel. Two shock tunnels are currently accessible for this study, the first under the direction of the University of Kentucky, and a second under the direction of the Missouri University of Science and Technology. The two shock tunnels differ in dimensions but share common construction materials. Energy realized from a shock tunnel is hypothesized to be a function of the shock tunnel’s dimensions. This study explores how different geometries affect the shock tunnel’s performance; this exploration is broken down into three phases. Phase 1: Open arena testing in which theoretical energies produced by the detonation of small (<1.0 kg) charges are compared to actual experimental values. Phase 2: Shock Tunnel testing in which realized energies are experimentally recorded for the UK shock tunnel. Phase 3: Analysis of the data to lay down the ground work for producing a pressure-forecasting tool given shock tunnel dimensions and explosive characteristics with the possible detection of avenues for optimization of shock tunnels.

Jan 1, 2009

By Larry Schneider

In 1998, the Blast Vibration and Seismograph Section of the International Society of Explosives Engineers formed a working group to collect and compile a list of regulations limiting ground vibrations from blasting. The goal was to locate those countries, states, provinces, and cities that have such regulations, identify which governmental body enforces them, and determine what limits on ground vibrations are imposed upon the blasting operations. In the course of this study, data was collected from over 60 jurisdictions where peak particle velocity restrictions range from non-existent to very stringent. Some of the regulations were found to be based upon standards grounded in good science, while others possess little or no technical justification. This presentation will summarize the findings of the subcommittee, focusing primarily on what the limits are, which type of blasting operations must adhere to them, and to what structures they apply. The degree to which these regulations are based upon valid scientific and engineering research will be discussed. A listing of specific locations having such regulations and information about those regulations will be provide

Jan 1, 2000

By Michael Wieland

Smoke/fume measurements from rapid transitory charge reactions are not wholly comparable with thermodynamic reaction code (TDRC) results, since quenched chemical reactions yield nonequilibrium concentrations. Though the work output and major reaction products are usually rendered with minor deviations, the toxic fumes and other minor concentrations reveal some major discrepancies. Work output for charge formulations in underwater or fixture tests were theoretically resolved with work-principal models that form a rough thermodynamic trajectory. Stalled nonequilibrium concentrations are rationalized by finding the underlying quenched reaction(s). The wide relevance of the Zeldovich radical-chain mechanism that transforms nitrogen oxide was previously recognized. The work-principal model (WPM) represents reaction quenching with off-trajectory constraints to render the fumes, without noticeably readjusting the work process. When restraints that characterize the confinement are WPM tractable, the resolution of critical reaction mechanisms is worthwhile, since they remain useful, regardless of the rich, neutral or lean stoichiometry of the charge formulation.

Jan 1, 2012

By Adrian Moore, Alan Richards

A real-time system for prediction of the effect of meteorological conditions on airblast overpressure levels has been established in the Hunter Valley Coalfield in Australia. Real-time meteorological data from continuously operating sounding equipment and a predictive meteorological model is input to an atmospheric refraction model that enables the effect of meteorology on airblast overpressure levels in the area surrounding the blast site to be evaluated. Graphical outputs from the model, which are superimposed over a scaled airphoto of the mine and surrounding area, show the extent that airblast levels will be increased. When combined with inputs that quantify the effect of blasting specifications, the airblast levels that will result in the surrounding area from the combined effect of blasting specifications is determined. The model permits those responsible for blasting to make more accurate decisions on suitable times that blasting may take place to conform with applicable airblast limits.

Jan 1, 2009

By Romel Villanueva, Juan Vasquez

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process. For gassed explosives the density varies gradually according to the depth in the hole, due to the pressure on the bubbles by its own weight. The density at the bottom of the hole can reach critical values, which directly affects the start of the detonation in the booster zone with a high probability of nitrous fumes formation. On the other hand, density translates into the amount of explosive and energy available. Therefore, for the optimum performance of the explosive, the minimum and maximum values of the in-hole density must be determined. For the cases studied, the maximum in-hole density and the maximum charge length have been determined. When the charge length is greater than 7.0 m [ 23 ft.] special care must be taken with the cup density, which as a general rule should not exceed the value of 1.15 g/cm3 [71.8 lb/ft3] at the risk of losing the sensitivity at the bottom, also increasing the probability of nitrous fumes, bad fragmentation and finding intact explosive after blasting. In the large holes in Toquepala and Antamina mines, where the charge length can be greater than 9.0 m [29.53 ft]. If the cup density is greater than 1.15 g/cm3 [71.8 lb/ft3] the in-hole density can easily reach a high value of 1.30 g/cm3 [81.16 lb/ft3].

By Alejandro Berrios, Matheus DaSilva, Erick Siqueira

Vazante mine is an underground polymetallic mine that produces zinc, lead, and silver, which belongs to Nexa Resources in Minas Gerais, Brazil. The mine, a sublevel stope underground mine, mainly applies two subvariants: VRM – Vertical Retreat Mining and Open Stope. In a specific place of the mine, the geology allowed the design of a production stope with larger dimensions than the standard stopes, commonly called Super Stope. At this place, the plan was to apply both sublevel variants simultaneously. This mining block comprises rings in two different levels, with access by two ore drives on each level; the dimensions would be approximately 50 meters high, 50 meters long, and 35 meters wide. Opening the Free Face to mine the whole Stope was a challenge due to operational issues, such as hazard risks from loading over void space, exposure to uncontained places, and the impossibility of implementing the optimal blast sequence. Wireless blasting initiators have gained popularity recently due to their convenience, safety, and efficiency. This initiation system was applied to preload all the rings required to open the Free Face, ensuring a safe and optimal blast sequence. Wireless initiation prevented hazard risks, enhanced the blast sequence to guarantee the required void space, and optimized the equipment's operational cycle. The blast crew carried out the activity without exposure to the risk of loading over void space. The wireless detonators also avoided after-blast activities, which were required to provide secure access to the blast crew, optimizing the operational cycle.

Jan 21, 2025

By John Cory, Ran Tamir

Blasting data analytics are being increasing used to increase mining productivity, reduce mining costs, maximize high margin aggregate products, and to reduce fines. Three examples will be illustrated using simple models to maximize the percentage of blasted rock within established dimensions and reduce fines-one from video fragmentation distribution information, the second from sieved crusher fragmentation data, and the third from plant production data. In addition, the use of sieved crusher results to determine blasting related fines and the use of mine productivity data to maximize aggregate sizes when pattern (burden and spacing) areas are changed will be illustrated

Jan 1, 2012

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By J. Rafael Otaíza, Francisco Mardones

This work has addressed the problem of creating a predictive model of the maximum particle velocities in the rock mass (PPV). The model designed specifically can model the subsequent vibrations of blasting based on geometric parameters, explosive loading, and the blasting process itself. Models based on artificial intelligence (AI) algorithms can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. These models have been successfully used in similar contexts (Prashanth, (2018)) and have achieved state-of-the-art results in the field (Lawal, (2021)). The main challenge is to adapt them to the context of Chilean mines, in addition to including the geometric information of the blasting and the heuristic to obtain the set of optimal parameters, it is proposed to follow the work of (Simonyan, (2013)) and obtain "saliency maps" adapting it to tabular variables. We implemented an Artificial Neural Network (ANN) with a large number of neurons in the hidden layers. Models based on neural networks can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. The literature shows that, for the problem of rock type identification, basic neural networks perform well (Simonyan, (2013)), but lack uncertainty estimates. This is a data-driven model, and in this sense, the model training was carried out using data from multiple operations in the large copper mining industry in Chile. In these databases, data consistency and the balance of the various independent variables that have the greatest impact on the model were ensured. With the above, the optimal hyperparameters of the model were determined, obtaining a predictive R-squared of 0.94.

Jan 21, 2025

By Anderson da Cunha Meireles, Pedro Garcia, Ernst Young, Leandro Coelho, Carlos Eduardo Soares Feliciano, Key Fonseca de Lima

Rock blasting is a crucial technique employed in mining construction and quarrying industries to fragment large rocks into smaller, more manageable pieces. However, it often generates ground vibrations that can pose significant challenges. This study explores the application of Conformal Prediction (CP) in the context of rock blasting to develop predictive models that estimate blasting-induced vibrations and quantify the associated uncertainties. Various machine learning models were integrated within the CP framework using MAPIE and CREPES libraries. The results demonstrated the effectiveness of CP in providing statistically reliable prediction intervals, making it particularly useful for applications where the stakes of underestimating uncertainty can be high.

Jan 21, 2025

By Clayton Thompson

Linear detonation wave generators (DWGs) shape a detonation wave so that every portion of the wavefront reaches the target “line” simultaneously. A projection-type linear DWG uses Gurney plate velocity predictions and Taylor deflection angle predictions to estimate the angle at which a thin projected flyer (typically metal) will impact a target. A mousetrap-style planar DWG consists of two projection-type linear DWGs working in succession to create a planar wave-front through shock initiation of each successive target explosive. The angle of deflection is critical to yielding a planar or linear wave profile. Gurney predictions, nominally accurate to within 10% of empirical results, may not yield ideal linear or planar detonation behavior when used with a grazing projection-type DWG, which typically requires accuracy within 2%. Simulations were conducted using AUTODYN hydro code to compare deflection angle prediction methods. Ranges of minimal error between Gurney and Taylor predictions and the results from the hydro code were determined, using PBX-9404-driven polyethylene flyers.

Jan 1, 2011

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By C H. Dowding, P W. Linehan

Many of the technical and non-technical or human problems associated with blasting can be minimized through a proper preconstruction test-blast program.

Jan 1, 1986

By Michael J. Sapko, Eric S. Weiss, Richard W. Watson

As part of the Bureau of Mines research into the hazards associated with the mining and processing of oil shale, experimental mine tests have been conducted to evaluate preferred combinations of explosives and inerting materials to prevent ignition of oil shale dust and mixtures of oil shale dust and methane.

Jan 1, 1989

By D Reid Watson

A unique blend of theory and hands-on teaching of blast hole drilling and explosives technology is being provided at a Canadian Community College. Students graduate at an apprentice level quite capable of operating and maintaining blast hole drills and designing and executing surface blasts.

Jan 1, 1987