Search Documents

By Gibson J.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 3rd June 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-84, included a written contribution by Parfitt I.C. and the author's written replies to this and previous discussion

Dec 1, 1916

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

By E. L. Evans

The historical development of South Yorkshire mining is traced and note made of the liability to generate spontaneous combustion of some of the seams which have been worked. The liability factor is analysed firstly as an inherent property in the material of a coal seam, and secondly as a circumstance of a situation in which access is provided for the air necessary to sustain oxidation. The geological settings in which incidents of heatings have been known to occur is discussed and conditions favouring a natural pre-disposition to spontaneous oxidation exposed, particularly the effect of argillaceous material overlying the seam. An extensive strata-dynamic study follows to demonstrate the situations in which stray air currents tend to impinge on readily oxidizable material. Prevention techniques are indicated as the identification of strata-dynamic situations in which air access to broken coal is induced and thereafter th operational action to seal off the voids which have been opened up so as to exclude air from the broken coal. Measures to reduce the tendency for ventilating air to short circuit across waste voids, and to obviate deflection of air into packs are outlined. The importance of face and roadway design features is demonstrated and the consequences of practices inimical to good control of spontaneous combustion are related. Discussions on means of detection and also on the sealant materials available are included.

May 23, 1905

By Dobson C. L.

The memoir, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne on 3rd June 1916, outlines the career of one of the Institute's oldest members and past-president 1896-1898, including the improvements he introduced at Harton, St. Hilda and Boldon collieries and his activities with the Institute and the Durham Coal Owners' Association

Dec 1, 1916

By L. R. Chimimba

"The Trojan nickel deposit occurs within a pile of ultramafic lavas subjected to a lower amphibolite grade of metamorphism. The lavas form part of the Upper Greenstones (Bulawayan Group) of the Mazoe greenstone belt. The nickel mineralization occurs as disseminated, massive and near-massive sulphides. The massive and near-massive ore occurs along the basal contact of the serpentinite units and is overlain by the more abundant disseminated ore, which occurs within the serpentinite. The main sulphide minerals are pyrrhotite. pentlandite and chalcopvrite. Minor amounts of millerite and pvrite are present. The Ni : Cu ratio in all three types of ore averages 15:1.The intercumulus nature of sulphides in the near-massive ore and similar textures occasionally seen in the disseminated ore indicates a magmatic origin of the mineralization. The basal position of the near-massive and massive ore suggests that the sul­ phides settled out under gravity during the emplacement and crystallization of a peridotitic magma. The deposit has been deformed and some of the primary massive ore has been remobilized into veins and breccias. The disseminated mineralization now occurs mainly as blebs of sulphides intergrown with silicate minerals or as stringers of sulphides between foliation planes in the serpentinite."

Jan 1, 1984

By G. Richards

Application of the Internet of Things (IoT) technologies - the interconnection of uniquely identifiable embedded computing devices within the existing internet infrastructure - to the mining industry is discussed. IoT technologies are aimed at making projects safer, better optimised and more economic and are applicable to current or new underground or open-pit mines, regardless of size. Two examples are presented of successful implementation of IoT technologies, the Chelopech gold, copper and silver mine in Bulgaria, where production has increased from 500 000 to 2 000 000 tonnes/y and communication costs have been reduced by US $2 500 000 over 2 y, and the Pilbara project in Western Australia, where remotely controlled wirelessly connected autonomous trucks have covered ca. 3 000 000 miles and hauled almost 250 000 000 t of ore since 2008

Apr 1, 2015

By J. A. Saunders, E. L. Rowan

It is now widely accepted that the metal-rich waters found in the oil wells are possible present-day analogues of the mineralising solutions that formed the Mississippi Valley-type (MVT) deposits throughout mid-continental USA and elsewhere. A study characterising the trace-metal content provides additional circumstantial evidence for a genetic link between sediment-hosted mineral deposits and basin brines: Ag, Co, Ni, As and Mo, detected in the scale, are locally present in accessory minerals in MVT deposits and the levels of Ag found in the wells support the conclusion that sedimentary sources for silver should be considered in evaluating the origin of Pb-Zn-Ag deposits in sedimentary terrains

Jun 12, 1905

By J. R. Hammond, I. C. Herbert

Report of discussion at October, 1970, IMM general meeting (Chairman: M. J. Cahalan, President) and contributed remarks on the paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, June, 1970, pp. C128-36 and introduced by I.C. Herbert. Contributors were von Struve G., on the application of balling discs and the use of basic additives; Young P.A., asking for details of the drying, grinding, balling, induration and specification testing equipment and processes; Davison J. on pellet swelling properties and Carter G.C. on disc operation, refractories and green ball properties.

Dec 1, 1971

By Schwartz M.

The current status of the heavy and light rare-earth elements outside China is reviewed. New suppliers of the light rare-earth elements are Lynas (Australia/Malaysia) and Molycorp (USA), which are anticipated to process 11 000 and up to 10 000 t/y, respectively, and the most advanced heavy rare-earth elements project is Avalon's Nechalacho project at Thor Lake, Northwest Territories, Canada. U3O8 Corp has potential rare-earth elements production, e.g. ytrrium and neodymium, from its Berlin deposit in Colombia and Namibia Rare Earth's Lofdal project (Area 4) has potential to produce an average of 1 500 t/y of separated rare-earth oxides. With regard to the three historical producers, India has some small-scale production, Brazil has been a small-volume producer and has potential for new heavy rare-earth elements production, while South Africa has no current production

Feb 1, 2015

By A. Ludkin

The paper presents the history of the occurrence of spontaneous combustion in the north area, together with the associated problems. These are examined and a description is given of the methods used to combat the danger, including the use of modern scientific instrumentation. Detailed reference is made to the underground trials with pack injection and sealant coatings which were carried out at Seafield Colliery following the formation of a working group to assess the performance, in the same underground conditions, of (1) sandbagging, (2) pack injection, (3) surface coating. Based on these trials, an improved and more economical method of prevention has been established. There is, however, still scope for further improvement in techniques which would take into account the problems of gradient, transport, manpower and cost.

May 23, 1905

By S. Y. Ezz

Report of discussion at February, 1971, IMM general meeting (Chairman : M. J. Cahalan, President) of a paper published in Transactions/ Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C226-C233 with contributions by Wild R. and Astier J. on fluidised bed reduction of iron ore fines

Dec 1, 1971

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

By R. F. Bell, Schultz

The paper briefly discusses the nature of spontaneous heating in mines in the Doncaster area, in the period immediately before 1967 and steps taken to prevent and treat such outbreaks. The changes that led to the increased rates of advice of Barnsley Seam faces since 1967 are listed and the effects of these increased rates on the frequency and location of spontaneous combustion are discussed. The change in methods of control required by the increased rate of advance of the faces and the changes in location of outbreaks are described. Some typical heating situations are evaluated. The methods described include the use of air sealants, water gels for filling of voids in wastes, the balancing of pressures across heating areas by pressure chambers, booster fans, and the resiting of air separation doors, and the sealing of air-ways by flooding. The authors discuss the influence of mine layouts on the risks of spontaneous combustion and advocate that future plans should be designed to limit the number of districts at risk when heatings occur.

May 23, 1905

Discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-90, included written contributions on size and gauge standardisation by Lupton A., Peck W.R., Dean S., Mayer R.W. and Ashworth J., with the author's written response, and by Bulman H.F. and Brown M.

Dec 1, 1916

By M. L. Schmulian

"The Windarra nickel deposits display many of the characteristics that typify Archaean volcanic peridotite-associated nickel sulphide ores of Western Australia. The Fe-Ni-Cu sulphide mineralization, which comprises dominantly disseminated sulphides, occurs at the base of a differentiated ultramafic volcanic pile grading upwards from massive meta-peridotitic flows to thin, locally spinifex-textured meta-picritic units. The entire mafic-ultramafic belt has been subjected to mid-amphibolite- facies metamorphism. The ore-bearing ultramafic is immediately underlain by dominantly sulphide-facies banded iron formation (BIF), which commonly contains nickel sulphides adjacent to its contact with mineralized ultramafic. BIF-hosted ores are formed both by physical remobilization of ultramafic-hosted sulphides and by migration of Ni and Cu into pre-existing iron sulphides.At Mt. Windarra the mineralization comprises eight steeply dipping, steeply plunging elongate oreshoots, which display a marked parallelism with major and minor fold structures in the underlying BIF. Seven of the shoots occur at or close to the base of the ultramafic pile, and are hosted by at least three overlapping flows. The zone of overlap occurs at the northern end of each flow, where picritic ultramafic, representing a dominantly liquid portion of the flow, occupies the basal contact. A gross south- north ultramafic flow direction is inferred. The eighth shoot occurs in a stratigraphically higher position within the ultramafic sequence.At South Windarra at least two overlapping mineralized flows occupy the basal contact, the ore zone having a strike extent three to four times its downdip extent. There is no obvious structural control to the mineralization."

Jan 1, 1984

By Mohammed Ali Shah, Martin Waller

The mining industry depends to a large extent on the availability of high performance equipment. For drilling this means a requirement for well engineered, reliable machines with mechanised handling and widespread utilisation of automatic control. Such machines enable performance optimisation of drilling operations and integration into a high productivity mining system. A review is presented of the current status of drilling technology as applied to the mining and minerals industry. This covers developments in: drill bit materials and design; drilling techniques; machine design; mechanisation; automation; and drilling control. It also covers the ways in which current and future mining methods and practices will influence the applications and demands placed on drilling activities. The probable impact of current research on the industry is discussed.

Jan 12, 1992

By G. G. Lambert

The paper traces the pattern of spontaneous combustion in the workings of what was originally Hemsworth Colliery, but since July 1967 is now part of South Kirby Colliery. Examination is made of the Barnsley Seam sections and the part played by the top section of the seam as it comes in close proximity to the main seam. In this area of the colliery nine mechanised faces were set away between the years 1953 and 1968, every one "fired" at the pillar edge and six "fired" at the face line when production had ceased. The paper deals with the different preventative measures used, from sandbag walls, cement injections, spraying with polyurethane, until finally using Mandoseal as a sealant. Since the latter method was first used, the last three faces worked in this particular area were all salvaged completely, without any sign of a heating developing.

May 23, 1905

"Prior to the publication of the General Report of the Miners' Phthisis Prevention Committee of South Africa in 1916 little attention was paid to the dust hazard and the necessity for its suppression in the underground workings of the Broken Hill mines. Such precautions as were observed for the elimination of dust were related rather to the prevention of lead poisoning, which, in the early days of Broken Hill when large tonnages of lead carbonate ore were being won, was rather prevalent. Ventilation and hygiene followed the general practice in this and most foreign countries.This paper covers incidence and action since 1918, considering medical aspects and operating aspects. "

Jan 1, 1947

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

By P A. Collier

The general view of the author is that all the good intentions of manufacturers can fail completely if the variations in circumstances in underground mining are not considered at all times. With a belief that it is the customer that has the experience and know ledge of problems which occur on long installations. Reilloc talk with customers in coal mines around the world, and have done so from their inception. With considerable experience in their home market, their technical approach was received with enthusiasm by coal companies in both Australia and South Africa, and whilst experience was obtained in other countries, it is the particularly close working relationship in these two areas that is covered in this paper. The refinement of manufacturing techniques and the fine tuning of the specification to which the chain is made was developed in conjunction with factual underground experience obtained by customers as they sought to improve their productivity and a reduction in working costs. With a reliable product the mines are able to concentrate on improved operational techniques to extend the useful working life and plan for multi-panel usage of the chain.

Jan 5, 1996