Search Documents

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

A study of the thermodynamic properties of magnesium chloride ammines was carried out with the ultimate objective that the thermal decomposition of the hexammine MgCl2.6NH3 may prove successful on a commercial scale for the manufacture of anhydrous magnesium chloride, which is required for the efficient electrolytic production of magnesium. The experimental data are presented in the form of an equilibrium diagram that aids the understanding of the conditions associated with the thermal decomposition of ammines

Jun 13, 1905

By M. D. Gibbs, T. N. Smith, B. Verbaan

When heated in the absence of oxygen, pyrite from refractory gold concentrates decomposes endothermically to pyrrhotite, releasing sulphur. The decomposition starts at the particle surface and progresses inwards, leaving an adhering layer of porous pyrrhotite. Use of the conventional shrinking-core model implicitly assumes a negligible partial pressure of sulphur in the bed, but this pressure is in fact at least equal to the equilibrium vapour pressure of sulphur over pyrite, constituting the principal control of the rate of decomposition. Further experiments showed a decrease in reaction rate as the conversion increased. Both phenomena are attributed to the persistence of non-isothermal conditions in the fluidised bed during pyrolysis, caused by the endothermic nature of the reaction and the relatively slow rates of heat transfer to particles and vapour removal from the bed. Equipment must be developed to maximise these two parameters

Jun 19, 1905

By Schwartz M.

Respect for mining in Botswana is long-standing. This article looks at Africa's most transparent mining regime and some of its ambitious plans. Botswana's mining industry value is forecast to average 5.2% growth from 2014-2018 with solid growth for the diamond sector and acceleration of coal production. Respect for the country's mining regime is maintained in the Fraser Institute 2014 annual survey where Botswana occupies the 26th position of 122 administrations. Botswana's transparency is illustrated by Mupane gold mine near Francistown, Ghaghoo diamond mine in the Gope area and the Morupule coal mine

Mar 1, 2015

"The sulphide nickel resources of Australia are concentrated in the Western Australian Shield. This shield is considered to have developed by extensive, but incomplete, Proterozoic reworking of once-continuous Archaean crust. It now constitutes relic Archaean cratons and intervening orogenic mobile belts transected by narrow, curvilinear tectono-thermal mobile belts of younger Proterozoic age. Remnants of the Archaean cratons are exposed in the Yilgarn and Pilbara Blocks. In the former an ancient (to ca 3600 m.y.) high-grade gneiss terrain (Western Gneiss Terrain) occurs along the western margin of the block and is interpreted to flank younger (ca3000-2800 m.y.) greenstone belts to the east. Ancient (to ca3500 m.y.) granitoid-greenstone terrains dominate the Pilbara Block.Proterozoic mobile belts contain only traces of nickel mineralization, except for one locality in the Halls Creek Province. The Archaean high-grade gneiss terrains contain no important mineralization, and the Pilbara granitoid-greenstone terrains contain only scattered examples of less important types of mineralization.The important deposits (e.g. Kambalda, Windarra, Agnew, Mt Keith) are all of komatiitic affinity and are best developed in the youngest greenstone belts of the eastern part of the Yilgarn Block. In particular, they are concentrated within, and adjacent to, the Norseman-Wiluna Belt, which contrasts in age, lithofacies and structural style with all other greenstone belts in the shield. It is interpreted to have been a rift zone. Within this belt the two main deposit types—the volcanic peridotite-associated and intrusive dunite-associated deposits—are concentrated into spatially separate zones. Precise controls on this heterogeneous distribution cannot be determined unequivocally from available data. One possibility is that the major volcanic peridotite-associated deposits were developed selectively in the actively subsiding axial part of the rift zone during the early extensional phase, whereas intrusive dunite-associated deposits were formed during a subsequent (less active?) stage of volcanic basin development. Distinctive sub-types (facies) of the volcanic peridotite-associated deposits form clusters that are generally within the rift zone. These may represent deposits related to discrete eruption centres, and at least part of their variation is due to relative position within extensive, topographically confined, linear flows."

Jan 1, 1984

By C. H. J. Beaven, M. P. Jones

Since the various new techniques of automation and computing have enabled vast numbers of mineralogical observations of relatively small samples to be made cheaply and rapidly, the statistical assessment of these measurements has become of vital importance. Much of the theory and most of the procedures of sampling that are used in the mineral industry are based on Gaussian statistics, but modern measuring techniques show that many mineralogical parameters do not necessarily follow the Gaussian distribution function. Consequently, it has become necessary to examine the application of other, more suitable statistical methods in order to derive the maximum amount of useful information from the examination of mineralogical samples. Some of the errors that can be introduced by the use of incorrect distribution functions are discussed and the value of determining the function that is appropriate to the particular parameter that is being measured is shown. Examples are provided of non-Gaussian distribution functions in mineralogical materials that were encountered during prospecting and during mineral treatment operations: a Canadian uranium ore, a Thai tin ore, and gold ore tailings.

Dec 1, 1971

By O. E. Polter, W. J. N. Fernando

Smelter-grade alumina is usually produced by the calcination of gibbsite. The ideal energy requirements for the calcination of gibbsite have been analysed and compared with the actual energy consumption of some industrial calcination processes. The consumption of most of these is considerably in excess of the ideal. Methods suggested for calcining dry gibbsite feeds which claim energy savings of 10-14% consume 26-34% more than the ideal energy requirement for dry feeds. This study indicates that it should be possible to recover appreciably more energy, giving further improvements in fuel efficiency, both in existing gibbsite calcination processes and in methods that have been proposed for the stagewise calcination of dry gibbsite

Jun 13, 1905

By J. Coxon, G. W. Walker

The paper describes the discovery, location and events concerning three types of heating which have occurred in recent years: a) in a district being salvaged, b) in the shaft pillar at an air-crossing, and c) in the gate side of a production district, all of which have occurred in the Beeston Seam at collieries in the deeper eastern part of the area. The paper describes the precautions, air sampling arrangements, training methods and codes of practice which have been adopted at collieries where spontaneous combustion is, or is likely to be, a hazard. The air samples taken from behind the stoppings following the sealing off of the salvaging district are examined and interpreted. The problem of effectively sealing off where more than two stoppings are required is made apparent. Other lessons have been learned as a result of these heatings and are described in the paper.

May 23, 1905

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Bareley, E. Rothery, S. H. White

B.P.J. Stevens contributes a further response to the authors' earlier lengthy reply regarding their paper published in Trans.IMM B, vol.104, 1995, p.B1-B17, contending that despite the positive contribution clarifying their interpretations they perpetrate some misquotations, attempt to rewrite history and fail to understand the New South Wales Geological Survey's stratigraphic interpretation of the Broken Hill area. The paper's authors, in their further response, robustly defend their views, insisting that Stevens tends to misquote or take out of context what they have written and reiterating their findings that Zn is tectonically stacked above Pb at the north end of the orebody, that the written development of the stratigraphic interpretation is as they have stated, that shearing has attenuated or removed fold limbs in the Broken Hill block and that the 1:100 000 stratigraphic map reveals that magnetic anomalies are oblique to and truncated by the Geological Survey's interpreted stratigraphic boundaries

Jun 19, 1905

By Williams J. A.

"Changes proposed in 1969 to modernize legislation governing the exploitation of mineral deposits in the United Kingdom serve as the basis for a discussion of what is considered to be a desirable framework for future legislative proposals.Proposals with regard to prospecting and exploration, evaluation, and acquisition and exploitation are considered, as are suggestions relating, inter alia, to aerial surveys and land restoration.It is concluded that without legislation along the lines proposed there can be no significant revival of metal mining in Britain."

Dec 30, 1971

By D. C. Cooper, P. M. Green, J. A. Plant, P. R. Simpson, A. J. Reedman

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The Grampian Highlands and English Lake District evolved as part of the American and European continental plates, respectively, and were separated by the Iapetus Ocean until they were tectonically juxtaposed during the late stages of the Caledonian orogeny. The similarity in the controls of the distribution of gold pathfinder elements and gold mineralisation in the two regions thus provides important information for understanding the genesis of gold deposits in comparable tectonic settings elsewhere. The data presented are inconsistent with models that invoke a juvenile source of gold or its pathfinder elements. Instead, they support a model whereby gold and its pathfinders were initially concentrated in volcano-sedimentary sequences in rapidly subsiding, tectonically controlled basins and in associated volcanic rocks. Remobilisation and mineralisation occurred subsequently, probably as a result of an increase in oxygen fugacity associated with the influx of granite magmas into the crust and the establishment of hydrothermal convective circulation systems

Jul 1, 1991

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

By Gibson J.

Written discussion contributions to the paper presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, comprise comments by Kilpatrick W.M., Routledge W.H., Watson J. and Smith W., along with the author's reply. Also briefly noted are the demonstration of two pieces of equipment, an incline chock and a cage arrestor

Dec 1, 1916

By D. Mireku-Gyimah, R. S. Suglo

Ghana contains auriferous belts which cover 51 800 km2 of its small area of 239 400 km2. From 1493 to 1600 35.5% of the world gold production was from the Gold Coast (renamed Ghana in 1957). This dropped to 8.9% from 1701-1800. For the past fifteen years annual production has averaged less than 2% of the world total. By 1985 only four gold mines were operating, compared with 45 in 1934 and 11 in 1945. Since 1987 Ghana has experienced a boom in gold mining activities. By 1991, 83 new companies had acquired prospecting licences. At least five new companies have started large-scale production. About 650 licensed small-scale mining groups are in operation. The economic and technological factors that have contributed to the decline of gold production in Ghana are discussed. A summary is given of the methods used to mine and recover gold. These cover small-scale workings, dredging, open cast operations and underground mining. The advantages and disadvantages of these technologies and the future of gold mining in Ghana are considered.

Jan 4, 1993

By E. C. I. Hammerbeck

"Geological controls and constraints in space and time define the milieu of the nickel deposits of Southern Africa. Primary, magmatic deposits are of two types, e.g. synvolcanic or syntectonic deposits confined to certain orogenic domains, and those related to intracratonic, post-orogenic magmatism, e.g. the Great Dyke, the Bushveld Complex and the Insizwa intrusion. Epigenetic and supergene deposits form a separate, unrelated group and are of minor economic importance.The metallogenic evolution of syntectonic nickel deposits is particularly well illustrated in the Zimbabwean Province, where the relationships between Archaean greenstone development and nickel mineralization are best illustrated. Volumetrically subordinate, nickel-poor greenstones in the 3500 m.y. old Sebakwian Group are followed by more common komatiite development in the Lower Greenstones (3000 m.y.), and, finally, by very significant komatiites with important nickel mineralization in the 2700 m.y. old Upper Greenstones of the Bulawayan Group. Comparable nickel mineralization is not known in the Raapvaal Province, in spite of ubiquitous komatiitic magmatism of the Onverwacht Group (3500 m.y.) and other greenstone sequences. No komatiitic rocks younger than about 3200 m.y. are known in this region, orogenic activity in the Kaapvaal tectonic province having ceased at about 3100 m.y., whereas the Zimbabwe Province remained tectonically active until at least 2600 m.y.The tectonic environment, host-rock petrology and mode of emplacement, as well as some details of the nickel mineralization, are the parameters employed to classify the Southern African magmatic nickel deposits. A rating of the deposits is introduced that reflects the original resources of the deposit, its average nickel content, its mining history and potential to facilitate ready comparison with and assessment of the nickel deposits listed in the classification, as well as some important nickel deposits worldwide."

Jan 1, 1984

By W. H. McAllister

The paper considers the geology and the coalfields that comprise the Scottish south area. It traces the history of known sources of spontaneous combustion and indicates the collieries concerned, with the position of the seams in the geological series where heatings have occurred. The methods of work over the years are described. It relates in detail the circumstances surrounding a fire at Bilston Glen Colliery in the Lothian Coalfield, and the heating at Killoch Colliery in the Ayrshire Coalfield, and the steps taken to deal with them. It also describes some of the difficulties in steep seam working. Methods adopted to prevent spontaneous combustion throughout the area are discussed, and some detail of the UNOR gas analyser is given. Finally, it comments on the present techniques in use in the area, particularly at Bilston Glen Colliery, to prevent spontaneous combustion.

May 23, 1905

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991

By C. J. V. Wheatley

Recent studies of the mineralisation at Avoca in southeast Ireland, Parys Mountain in Anglesey, and Coniston in the Lake District result in the proposal of a new metallogenetic model for mineral deposits in the Southern Caledonides. A regional pattern of metal zoning exists, an axial belt, including the major copper deposits, being bordered by areas with lead-zinc deposits. Conformable lenticular pyritic zones occur in the central belt, closely associated with acid volcanic sequences and, often, post-dating them. These zones are thought to have been formed in a marine environment, mineral growth taking place below the sediment-water interface, whereas magnetite-rich zones developed under different Eh and pH conditions. Stockworks containing appreciable copper and, in some cases, lead and zinc were developed at a later date, stratigraphically below the pyritic zones, by migrating hydrothermal chloride and metal-rich fluids. Complex lead-zinc-pyrite mineralisation resulted from the reaction between pyritic zones and the final fraction of the hydrothermal fluids. Crosscutting vein-type fissure infilling mineralisation occurs in every mineral field. These deposits apparently comprise a pulsatory metasomatic sequence, closely related to tectono-stratigraphic controls, ore localisation being influenced by the coincidence of suitable structures and pyritic shale horizons. The implications for mineral exploration are considered and it is concluded that the model offers an explanation for the existing pattern of metal zoning; and it may have wide applicability to mineral deposition in geosynclinal sequences.

Dec 1, 1971

By R. J. Howarth, P. L. Llowenstein

The errors resulting from field sampling, sample preparation and analysis are investigated for drainage sediments derived from homogeneous sandstone, shale, limestone, basic igneous and granite lithologies as a background to a primary reconnaissance survey of England and Wales. Emission spectrographic analyses of approximately 350 samples for Al, Ca, Fe, K, Si, Ba, Co, Cr, Cu, Ga, Li, Mn, Ni, Pb, Sc, Sn, Sr and V and atomic absorption analyses for Cu, Ni, Mn, Co, Zn and Pb have been treated statistically. For routine broad-scale surveys analysis of the unground -80-mesh sediment fraction proves satisfactory. Sampling error between localities in a stream is shown to be less than spectrographic analytical error for many of the elements considered here, except where mineralisation (contamination) occurs, but exceeds the atomic absorption analytical errors in most cases. Unless it it critical to reduce the amount of between-site variability (having regard to analytical errors) in the regional survey, there appears to be no advantage in the use of a more sophisticated sampling technique. The utility of moving-average maps in reducing the width of the confidence belt around the regional 'geochemical surface', and thus compensating to some extent for the sampling errors, is also demonstrated.

Dec 1, 1971

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992