Search Documents

By A. Ouchi

This paper presents ground control best practices in weak rock environments including the "Unsupported" Weak Rock Updated Span Design Curve and awareness pertaining to the potentially detrimental effects of using resin grouted rebar in weak rock masses and the false sense of security that the use of resin grouted rebar may instill. Ground support is almost always used in weak rock environments, though the type of support used can vary widely. The development of the Weak Rock Updated Span Design Curve by the addition of 463 case histories of RMR76 values ranging from 25 to 60, has also been calibrated to four different support categories; Category A: Pattern Friction Sets, Category B: Pattern Friction Sets with Spot Bolting of Rebar, Category C: Pattern Friction Sets with Pattern Rebar Bolts and Category D: Cablebolting, Shotcrete, Spiling, Timber Sets or Underhand Cut and Fill. Design of underground man-entry type excavations in North America relies heavily upon empirical analysis. This design requires a higher Factor of Safety than other non-man entry type excavations. A comparison of the calculated ½ span failure Factor of Safety between all the categories is also presented.

May 1, 2009

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

By D. Fleury

"This paper describes the challenges of mining a sill pillar under various types of paste backfill quality. From 1994 to 2002, Louvicourt mine produced approximately 12,600,000 t grading 3.5% Cu, 1.5% Zn, 27 g/mt Ag, and 0.85 g/mt Au. The mining method is transverse blasthole stoping, mining primary and secondary stopes. The production of this 4,300 t/d operation was accomplished using two mining horizons; from the 655 m level to the 415 m level and from the 860 m level to the 680 m level. The main sill pillar is between the 680 m level and the 655 m level. The second sill pillar is between the 885 m level and the 860 m level representing a quarter of the main sill pillar in size. Since 2002, production has gradually decreased and mining activities are expected to end in mid-2005. The sill pillar production will represent almost 25% of the total mine production. The overall recovery of the sill pillars stopes will be discussed in this paper. To recover the sill pillars, more than 1,500 m of development was planned in or under paste backfill. The first sill pillar stopes under paste backfill were mined out in 2002 with excellent results."

Jan 1, 2005

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

By J. K. Gowans

"INTRODUCTIONTo bring a mining property into production in the Canadian High Arctic a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these factors, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gained at the Black Angel Mine on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during this small ''shipping window."" The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months production was gained by opting for the ""Barge"" approach.What the Arctic winters do to the shipping season, so do they affect the productivity and the cost of labour. Construction labour must come from southern Canada. Thus higher transportation costs and higher wage rates, with more overtime and incentives, increase the labour costs to approximately 50% over normal southern rates. Couple these rates with the lower productivity involved with men working in the extreme cold temperatures and the net effort is worth avoiding. A process plant being constructed in Southern Canada can take advantage of more accessible labour at lower costs, increased productivity and a faster construction schedule. The barge concept must still deliver the equipment and materials during the ""shipping window"" but it can in the completed form."

Jan 1, 1983

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

By Trevor Yeomans, David Yaschyshyn

"Placer Dome (CLA) operates the 90-year-old Dome Mine, in South Porcupine, Ontario.The milling operation currently processes 5 million tons of ore per year, from both the underground and Open pit mining operations, producing 320 000 ounces. The milling process is conventional crushing and grinding, with gold recovery by gravity followed by leach/CIP.Cyanide tailings are impounded in a large (325 ha) tailings area where cyanide is allowed to degrade naturally. Effluent is discharged seasonally during the summer and early fall months to maintain site water balance. Pond water is reclaimed for sole use within the mill process.In 1995, an Effluent Treatment Plant (ETP) was constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO S02/Air cyanide destruction module was added.During this time period, the treated effluent often failed toxicity tests required by the Ontario MISA Regulation, even though effluent chemical parameters were below permit limits. Two studies identified ammonia as the toxicant to Rainbow Trout, and free copper as the toxicant to Daphnia magna.From a literature study, and contacts within the Ontario Mining Association, the use of chelation as a final end of pipe treatment step to render any remaining free copper and metal fractions biologically unavailable was considered. Lab and plant scale tests followed.During the 1999 ETP operating season, the addition of the chelant EDTA (ethylene-diamine-tetraacetic-acid) commenced. To date discharged effluent has passed all toxicity tests.The paper will review the effluent treatment history, current effluent treatment plant operation, and detail the use of EDTA for successful toxicity control.History of Tailings Deposition, and Effluent Treatment From 1910 to 1995Over it’s ninety years of operation, the Dome Mine milling circuit has changed from the original 1910 stamp-mill mercury plant, to today’s modem 14 000 ton per day automated gravity and Carbon in Pulp based plant.By the 19803, a modern mill was operating on mainly underground mined ore. The plant was operating at some 3 800 tons per day, using fairly conventional processing routes.The number 4 tailings dam was being used for tailing’s deposition.All effluent treatment was by natural degradation of cyanide. Discharge was from decanting type structures during the summer months only, maximizing the use of natural degradation no tailings effluent was recycled for Mill use."

Jan 1, 2001

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By Unal Artan

It is well known in the robotics community that the ability to determine the position of vehicles in real time is a key enabling technology required for automation, traffic management, and to ensure safety in the presence of multiple vehicles. Because of this, the introduction of global positioning systems (GPS) has had a remarkable impact on the surface mining industry, enabling real-time tracking of mobile assets, improved safety, and production optimization. Unfortunately, satellite-based GPS is not available underground. This paper reports on the preliminary results of a study to develop a robust method for globally consistent mapping of large-scale underground mine environments. We believe that this may additionally become the first step towards the development of a novel underground positioning technology. Presented are preliminary results from data collected at two underground mines using an Atlas Copco ST14 LHD machine.

Oct 1, 2009

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

Safe underground mine backfilling with hydraulic fill requires efficient fill drainage and stable fill retaining walls or bulkheads. If any or both the above two requirements are not satisfied, such a backfilling operation creates unsafe conditions and may lead to backfill retaining wall failures. Mine backfill retaining wall failures are always associated with economic losses, fatalities and interruption to mine production. Mining industry wants to either reduce or eliminate these fill retaining wall failures. The fill retaining wall failures could be effectively avoided through the use of fibre reinforced shotcrete fill retaining walls and engineered drainage systems through the retaining walls. This paper presents the experience of the author in developing, implementing, and monitoring several hundred fibre reinforced shotcrete fill retaining walls at a mine in Australia with the highest safety standard. The details on the mine backfill drainage system and fibre reinforced shotcrete fill retaining wall designs are also presented.

May 1, 2007

By A. Galibois, M. Fiset, T. Vo Van

"RÉSUMÉUn groupe de 22 objets prov enant des Forges du St-Maurice a été étudié de façon systématique par analyse chimique et examen métallographique afin de préciser leurs caractéristiques et d&apos;en évaluer la qualité métallurgique.La plupart des échantillons de fe r forgé et d&apos;acier sont hétérogènes tant au niveau structural que composition chimique. L&apos;examen de quelques produits fin is a mont ré qu &apos;on appliquait des traitements superficiels bien que le contrôle métallurgique fût plutôt empirique.AbstractA group of 22 specimens originating from ""Les Forges du St Maurice"" has been systematically studied by chemical analysis and metallographic examination in order to determine their characteristics and to evaluate their metallurgical quality.The bulk of the forged iron and steel samples are heterogeneous from both their microstructure and their chemical composition. Observation of a few finish products has permitted to establish that surface heat treating was applied although its metallurgical control was rather empirical."

Jan 1, 1984

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

In some parts of the world explosions in mines are more commonplace events. Even in the more developed nations explosions have occurred in recent times. In some cases these mines have significantly lowered their lost time injury frequency rates and as such considered themselves to be ?safe? operations. The consequence of these explosions has been devastating. It is not just the loss of those underground, but also to the families that have lost people in them and the broader community that has lost friends, income, business opportunities, and in many cases support and sponsorships. It begs so many questions, ?What went wrong??; ?Why were the circumstances not foreseen??; ?What could have been done to prevent it??; ?How is it that no one stopped it, reported it, fixed it etc.??. Being held accountable for negligence, should not be overlooked, however this may not aid the processes required to find all the answers. If the nature of explosions is understood, the circumstances and tools to prevent them are readily available then the occurrence and reoccurrence are due to weaknesses or inadequacies of the systems of work or in the implementation of them. This paper restates the fundamentals of gas explosions, examines the options to control the underground environment through ventilation, gas management and monitoring, education and training. Case studies have been used to examine systematic failures in ventilation management. In some of these cases it is not so much, the system that had been developed, but the interpretation and implementation of the system that resulted in the failure and subsequent loss.

Aug 1, 2013

By G. Barbery

"Particle composition distribution is an essential feature of materials processed by physical separation methods. The amenability to segregate a feed material in a concentrate and a tailings stream depends to a large extent on what is called usually the ""liberation"" of the various mineral phases that are present in an ore. In fact the energy consumed in crushing and grinding has the major justification of producing particles that are as close as possible to monominerallic. Monophasic particles are able to reveal physical differences in mineral properties that make their separation possible. For many years, various authors have insisted on the concept of liberation, without noting that, in practice, it can be a pure concept which does not lead to measurements or predictions. The present paper insists on the concept of particle composition distribution, in which the complete distribution is the information to be obtained, and not the ""liberation·· of various phases, just like for particle size distribution, the complete distribution is an objective commonly desired, and not one or two values representing the coarse or fine fraction.2. NOTATIONS-EQUATIONSFor the purpose of the paper, a particle will be characterized by its volume Vp, and its volumetric composition with respect to a mineral of interest, which will be given the notation ""O"". All the other minerals present will be called ""1"". This notation does not imply that the particles are biphasic, but that we are interested in the composition of particles with respect to one phase only. The volumetric composition will be given the sybol m:"

Jan 1, 1986