Search Documents

By S. Steinlechner, S. Wegscheider

"In the past, the metallurgical industry was most of the time dedicated on their main commodity, recovering base metals like zinc, copper or lead but leaving other valuable side elements in the generated residues. As a result, these accompanying minor elements, like gold, silver, indium or also PGMs can be found in the dumps of the corresponding industry. Because of political unrest, strikes, economic reasons or decreasing primary resources leading to a high supply risk, also those mentioned minor elements moved into the focus of the recycling industry. Therefore, beside the base metals, first of all the recovery of those minor metals would be of high interest contributing to the economic viability of recycling processes, although they occur in much smaller quantities in materials. In this context, residues from zinc industry, like leaching residues or precipitation residues show high potential to carry silver as well as indium next to lead and zinc. Therefore, the paper summarizes carried out thermochemical calculations investigating a possible recovery of silver as well as indium by volatilization and the influence of zinc and lead on this process. Based on these theoretical investigations with HSC, trials in lab scale were done verifying the obtained results.INTRODUCTIONHuge amounts of iron precipitate, mainly jarosite get landfilled every year although there is a high content of valuable metals in this residue beside iron. Nevertheless, jarosite has to be dumped due to the presence of contaminating heavy metals. The accumulation of these residues takes up massive land on the one hand but also causes a series of environmental problems in ecosystems on the other. Moreover, some toxic ingredients such as arsenic and cadmium can be dissolved in rain water and are therefore harmful to the health of the aquatic systems. (Erdem & Özverdi, 2011; ÖzverdI & Erdem, 2010) Approximately 0.5 t of dry jarosite accumulate in the production of 1 t of zinc by the hydrometallurgical zinc-winning route (Svens, 2010). Jarosite is a precipitation residue formed during the iron removal. In general, the iron already exists in the zinc ore which is why zinc ferrite builds up during the roasting step of the zinc ore. Zinc ferrite is only soluble in strongly acidic solutions and during the hot acid leaching step it gets dissolved while zinc and iron enter the solution. It is necessary to get rid of the iron because otherwise it would deposit on the cathode first due to its precious character which would be harmful in the zinc-winning electrolysis. Nevertheless successful investigations were done by adding chlorine to the jarosite to recover silver. These findings leads to another residue which occurs in huge amounts – electric arc furnace dust (abbreviated with EAFD) from the iron and steel industry. In 2013 the annual electric steel production reached about 451 million tons. Around 15-20 kg of EAFD is produced per ton of steel in an electric arc furnace (EAF), creating approximately up to 9 million tons of dust per year. (Grabda, Oleszek, Shibata, & Nakamura, 2014; World Steel Association) Next to elements like zinc, lead and iron, chlorine and fluorine are present in this dust. While galvanized steel plates in the scrap act as a source for zinc, casting powders, flame retardants and synthetic coatings are responsible for the chlorine and fluorine contents in the dust."

Jan 1, 2016

By T. Guan, G. Fu, X. Zhou, L. Deng

"One kind of tailings from gravity separation of polymetallic mine contains 0.5–0.8% SnO2. The proportion of –0.037 mm size fraction of the tailings is 37.12%, and the distribution rate of SnO2 is 60.32% in it. For this tailings, two processing technology was carried out. One was felt-shaking table gravity separation in which the concentrate with a grade of 30% SnO2 at a recovery of 10% was obtained. Another was flotation-gravity separation in which the concentrate with a grade of 51.20% SnO2 at a recovery of 51.69% was obtained, but the dosage of collectors was as much as 990g/t. Therefore, the experimental research on the influence of grain size composition on the cassiterite recovery were conducted. The results show that: (1) the flotation recovery of the cassiterite distributed in +0.043 mm size fraction is only 10%, flotation recovery is not suitable for it; (2) a portion of cassiterite distributed in –0.01+0.005 mm size fraction could be recovered by flotation, but the tin flotation performance will be worsened rapidly and the dosage of collectors will be increased due to the increase of the content of –0.010 mm size fraction; (3) flotation processing is not suitable for –0.005 mm size fraction of the tailings. According to the results, a new technology has been carried out, that is discarding tailings by gravity separation-hydrocyclone desliming-flotation-gravity separation processing flow. The processing index is close to that of the flotation-gravity separation processing flow, and the collector dosage is decreased to 360 g/t by this processing technology. And, it has been achieved that the cassiterite slime is recovered economically and reasonably.INTRODUCTIONAs the density of cassiterite is higher than that of gangue, gravity separation is considered to be a low cost, pollution free, and effective process for cassiterite recovery (Wills, 2009). However, cassiterite is a kind of fragile mineral, over crushing is easy to take place and a large amount of slime is inevitably produced in the crushing and grinding of cassiterite. For the cassiterite slime exists in –0.043 mm size fraction, the efficiency of gravity separation decreases sharply. The production practice shows that, for the fine cassiterite, the recovery of tin exists in –0.043 mm +0.010 mm size fraction is about 13% through shaking table gravity separation, and the tin exists in –0.010 mm size fraction is almost impossible to be recovered by gravity separation. If flotation is adopted to recover fine cassiterite, the problems of high reagent dosage, high cost, environmental pollution, and poor economic benefit would take place. Therefore, the recovery of cassiterite slime is a worldwide problem. A key way to increase the utilization of tin resource and increase the economic benefit of tin mines is developing suitable beneficiation process for fine cassiterite."

Jan 1, 2016

By L. Zeng, Q. Feng, Z. Qiu, L. Ou, Central South University

It is well-known that the use of nanobubbles can significantly improve the flotation efficiency of ultra-fine particles. However, this is mainly focused on coal and phosphate rock flotation. In the field of nonferrous metal processing, the related research is few. In this paper, a small laboratory mechanical cell associated with a specially-designed nanobubbles generator was used to investigate the effects of nanobubbles on enhancing ultra-fine scheelite flotation. Nanobubbles were created and based on the hydrodynamic cavitation principle through Venturi tubes. Comparative flotation tests were performed using different tubes to evaluate the nanobubbles impact on the ultra-fine scheelite particle flotation recovery. In order to better understand the nanobubbles enhanced ultra-fine scheelite flotation, nanobubbles potential and size distribution were measured. The effect of nanobubbles on the particle aggregation and scheelite particles potential were also studied through the turbidity tests, microscope tests and zeta potential measurements. According to the results, the mean size of nanobubbles was about several hundred nanometers, and the surface of nanobubbles was of highly negative charge in alkaline conditions. The flotation recovery of ultra-fine scheelite particles was increased in the presence of nanobubbles. The zeta potential measurements indicated that the repulsive forces between scheelite particles decreased when nanobubbles existed. Through the turbidity tests and microscope tests, the promotion effect of nanobubbles on particle coagulation could be verified more directly. The existence of nanobubbles in flotation system promotes the particle aggregation, thus increasing particles apparent size and particles capture by bubbles, which may be the fundamental reason why nanobubbles enhance ultra-fine scheelite flotation.

Jan 1, 2016

By Minghao Hu, Hongbo Zhao, Jun Wang, Wenqing Qin, Rui Liao, Central South University

"In the present work, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS) analysis and electrochemical analysis were carried out to investigate the intermediate species and electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms. For bioleaching of chalcopyrite by the sulfur oxidizing microorganism Acidithiobacillus caldus, the redox potential was always lower than the appropriate value and chalcopyrite was mainly directly oxidized to polysulfide (Sn 2-), thus resulting in low copper extraction. As for bioleaching of chalcopyrite by the iron oxidizing microorganism Leptospirillum ferriphilum, chalcopyrite was mainly directly oxidized to polysulfide at the initial stage where redox potential was lower than the appropriate value and resulted in low dissolution rate. At the middle stage where redox potential was appropriate (about 350–480 mV vs. Ag/AgCl), chalcopyrite was mainly transformed to intermediate species of Cu2S rather than polysulfide, thus resulting in high dissolution rate. At the later stage where redox potential was higher than the appropriate value, chalcopyrite was mainly directly oxidized to polysulfide which caused the later passivation of chalcopyrite. Finally, a model of electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms was provided.INTRODUCTIONBiohydrometallurgy is considered as one promising mineral processing technique in processing low grade ores due to the advantages of simplicity, low cost and eco-friendly. Chalcopyrite (CuFeS2) is the most abundant copper-bearing resource, accounting for appropriately 70% of the known reserves in the world, while is recalcitrant to bio-hydrometallurgy mainly due to the coated passivation layer (Klauber, 2008; Li, Kawashima, Li, Chandra, & Gerson, 2013). However, the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching are still uncertain. The microorganisms assisting chalcopyrite dissolution can be mainly classified into three types, including mesophilic microorganisms (e.g., Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans), moderately thermophilic microorganisms (e.g., Acidithiobacillus caldus, Sulfobacillus thermosulfidooxidans and Leptospirillum ferriphilum), and extremely thermophilic microorganisms (e.g., Metallosphaera sedula, Sulfolobus sp., Acidianus sp., and Sulfurcoccus mirabilis). Moderately thermophilic microorganisms have a better prospect in the future industrial application of chalcopyrite bio-hydrometallurgy (Olson, Brierley, & Brierley, 2003; Rohwerder, Gehrke, Kinzler, & Sand, 2003). Hence, investigating the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching by moderately thermophilic microorganisms is of important significance, which will provide essential information for promoting chalcopyrite bioleaching by moderately thermophilic microorganisms in laboratory or industrial plant."

Jan 1, 2016

By J. Hoover

"IntroductionThis chapter will discuss the operational and maintenance aspects of a heavy media cyclone circuits as applied to coal processing and using magnetite as the media. It deals with heavy media bath separators in terms of types of media, equipment, circuits, media recovery, maintenance, and product handling. It will detail heavy media cyclone operation and supplement the previously described topics.The heavy media cyclone was first developed in the Netherlands by the Dutch State Mines in 1945. A cyclone plant was not built in North America until 1961. Traditionally, heavy media cyclones have been used to treat size fractions between 1lz in. (12 .6 mm) and 35 mesh (0.5 mm). High maintenance related to heavy media bath separators has recently prompted some plants to crush all raw coal to minus 2 in. for treatment in heavy media cyclones.The heavy media bath separators utilize only the force of gravity to make the separation between heavy and light particles. This requires lengthy retention time which can lower capacity and also is inefficient for finer particles. A heavy media cyclone utilizes centrifugal forces which are 20 to 200 times greater than the force of gravity. This means the separation between coal and the impurities occurs very quickly, therefore a low retention time is required allowing cyclones to have high tonnage capacities. Also these greater forces allow better separation for the finer particle sizes.Heavy media cyclones are now widely used to produce both metallurgical and thermal coal. Work is in progress to reduce magnetite consumption, extend wear life, increase tonnage capacity, improve separation efficiency and automatically control these cyclone circuits."

Jan 1, 1989

By D. Nower

"The supply of copper is expected to be at a large deficit in 2012. To recover from these deficits mining companies are required to maximize production and there is no better way to accomplish this than to optimize the use of their mobile mining equipment fleets. To optimize these fleets, each equipment type has to be monitored in its own unique way. Automation would not only improve production, but also minimize the safety risks and eliminate planning errors. The automated vibration monitoring of multiple systems on the shovel can determine the machine’s condition at all times. This reduces unplanned downtime and keeps critical shovels in production. This paper will discuss the details of how shovels can be successfully monitored, continuously. INTRODUCTIONP&H Mining, part of Joy Global, is the world’s largest manufacturer of above-ground mining equipment. Its electric rope shovels, such as Figure 1, with capacities up to 115 tons (104.3 metric tons), are used for high production loading in surface mines; its draglines, such as Figure 2, have bucket capacities to 160 cubic yards (122 cubic meters). P&H also produces blasthole drills, mobile mining crushers and other essential mining equipment. Headquartered in Milwaukee, WI, the company does business on every continent, except Antarctica. ECONOMIC FACTORSDue to the global demands for metals and power, mines are required to operate at full capacity. Mine operations cannot afford any critical assets to shutdown unexpectedly; depending on the ore type and quality, downtime for a single shovel can be as much as $300,000 per hour.Electric rope shovels are one of the most critical assets in open pit mining. They are very large, complex machines with DC or AC motors, multiple reduction gearboxes (some of them complex planetary) and multiple large rolling element bearings. This complexity, combined with the tough 24/7 service, results in too much unplanned shovel downtime, which can affect the entire downstream process."

Jan 1, 2012

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By K. Gardner

"Many deposits have a geological model developed early in the project stages, which is not always reviewed or modified as the project matures and production commences. Conversely, ongoing pressures, due to a combination of declining head grades, a push for increased revenue and a multitude of other reasons, leads to processing plant modifications, with the primary aim being to increase production. Often, the ore deposit knowledge is not sustained or developed during the operational stages to the level carried out during the prefeasibility and feasibility study phases. This results in the variability within the deposit being poorly understood and a lack of data and knowledge being available to support (and ideally optimise) operations particularly in an environment where the flow sheet has changed and ore feed requirements are complex.INTRODUCTION This paper presents a case study of ore deposit knowledge development and corresponding process plant operating strategy at the Ladolam Gold Deposit, commonly referred to as the Lihir gold deposit in Papua New Guinea. The gold deposit is located in a tropical equatorial climate on the east side of Lihir Island in the New Ireland Province of Papua New Guinea. Gold mineralisation was discovered in 1982, and was followed by a major exploration campaign by a joint venture between Kennecott (Rio Tinto) and Nuigini Mining Limited. The first drillhole was drilled in 1983, and after an extensive period of drilling consisting of 343 holes for 83,500 m, the final Feasibility Study was completed in 1992. The feasibility study was based on a Reserve base of 37.9 Moz in refractory sulphide ore, with gold extraction proposed to occur via whole ore pressure oxidation due to the refractory nature of the mineralisation. The Lihir Special Mining Lease (SML) was granted in 1995 to a new PNG company – Lihir Gold Limited, and Rio Tinto established Lihir Management Company to develop and operate the mine on behalf of LGL. Mining and processing of the deposit commenced in 1997. Newcrest Mining Limited purchased Lihir Gold Limited in August 2010, and subsequently completed a major plant upgrade including the installation of additional grinding, autoclave and carbon-in-leach capacity. Post commissioning of the upgrade, Newcrest has continued to increase throughput and production. A reinvigorated ore body knowledge development program has significantly assisted this process in identifying operating strategies for the process plant and delivering recovery improvement projects to address declining head grade and recovery due to increased stockpile feed and flotation circuit use."

Jan 1, 2017

By Daan Maijer, Wade Marquardt, Robert MacKay, Steven Cockcroft, Farzaneh Farhang Mehr

"To comply with the new Corporate Average Fuel Economy (CAFE) standards, the automotive industry is aiming to reduce weight and increase the power and efficiency of small displacement engines through the application of forced induction technologies. As an example, there are now several 2.0 litre turbocharged engines in production, producing in excess of 240 hp. To meet the need for improved fatigue properties in the engine blocks used in these high-output engines, a new water-cooled chill technology is under exploration at UBC in partnership with General Motors and Nemak. A series of experimental techniques were used to assess the capability of the new chill to extract heat from an A319 casting in the vicinity of the main bearing bulk head. The results show that this method has the potential to achieve a reduction in secondary dendrite arm spacing thus meeting the new microstructural specifications for these engines.INTRODUCTION The automotive industry is working to meet the stricter efficiency requirements laid out within the CAFE (Corporate Average Fuel Economy) regulations (Bastani, 2012; Cole, 1995; Mackay, 2011; Miller, 2000), while at the same time not sacrificing performance. One approach is to increase the use of lightweight materials, which leads to a decrease in the overall vehicle weight and fuel consumption (Cole, 1995; Mackay, 2011; Miller, 2000). Other approaches include smaller displacement engines and gas-electric hybrid drivetrains. However, one trend that is becoming clear, is a greater emphasis on force induction gasoline engines. This allows for weight reduction to be achieved with smaller displacement engines without sacrificing performance. One consequence of this approach is that the engine block materials are subject to higher in-service thermal and mechanical cyclic loads (Cole, 1995; Miller, 2011; Heysler, 2001) The fatigue properties of an alloy are strongly affected by a number of the, as-cast, microstructure features including, Secondary Dendrite Arm Spacing (SDAS), porosity and eutectic lamella spacing (including intermetallic ß-Al5FeSi platelets) (Mackay, 2010a; Mackay, 2010b; Viet-Duc, 2015; Casellas, 2005). It is generally accepted they can act as fatigue initiation sites and that a reduction in their size will result in an improvement in fatigue performance. For a given alloy chemistry, one of the key parameters affecting the length scale of all three is cooling rate (Mackay, 2000)."

Jan 1, 2017

By P. Belley

Prior to 2006, the filtration unit for leached sludge treatment (filter press) permitted the filtration, washing and drying of cake to 17% (w/w) moisture. That year saw moisture content abruptly increase to 20% (w/w), drastically changing the rheological properties of the cake. The cake became sticky and agglomerated. This led to major disruptions of operations and plant capacity (cake release and cake conveyor problems, complicating the subsequent steps of the process). The conditions for the filtration, washing and drying, were simulated to ease cake unloading without aggravating dust emissions (moisture about 17% (w/w)). All of the laboratory tests yielded a moisture content above 17% (w/w). Therefore, we concluded that the moisture problems were not due to a recipe change in primary material, but to an operational problem in the filter press. Through the laboratory results, the filter press operating conditions (washing ratio, drying pressure and drying time) were optimized to enable a reduction in cake moisture to 17% (w/w).

Jan 1, 2007

By Philippe Henry

HYDROMETAL is using suitable technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy while keeping the environment cleaner. Hydrometal is treating on average 60000 t per year of complex materials through a unique hydrometallurgical recycling concept. Zn, Cu, Sn, and Pb are the most important in volume, but in the last 15 years, Hydrometal has also developed a few specific recycling treatments for the minor metals including Ge, In, Co, etc. In 2010, Hydrometal commenced the recycling of RE (Rare Earths) from wastes generated by the RE refining industry in Europe and has decided to initiate new recycling projects for the RE recovery from the magnet or glass industries. Two case studies of recycling of materials in our integrated hydrometallurgical facility (Hydrométal) in Belgium are discussed: recycling of cerium from polishing sludges; and recycling of Ni- Co from cement produced in the zinc industry.

Jan 1, 2014

By J. F. Harkom

Introduction The importance of the preservative treatment of mine timbers need scarcely be stressed here. Increasing the life of mine timbers will reduce one of the major costs of mining and also conserve the available timber supply which lies within easy access of the mines. When treated, several species of timber may be used which otherwise could not be considered, owing to their short life. Another feature which should appeal to the mining industry is that wood preservatives are a mine product, and the benefit to be derived from the increased consumption of wood preservatives due to the example set by mine owners is not inconsiderable. Mine timbers may be divided into three classes when considering preservative treatments. (1) Timber obviously not profitable to treat owing to long natural life or short period of time in service. (2) Timber that obviously should receive protection from decay. (3) Timber installed in locations where the length of service required will depend on future developments, so that preservative treatments might or might not prove to be a profitable investment.

Jan 1, 1930

"THE PACIFIC CONTINENTAL MARGIN OF CANADA is de-fined, for the purposes of this paper, as the area sea-ward from the present mainland coast of British Columbia to the foot of the continental slope. It thus coincides with A. Sutherland Brown's Insular Tectonic Belt. The region is limited to the north and south by the political boundary with the U.S.A., the location of which is still in dispute.The region can be subdivided into: (1) an interior trough comprising the Queen Char-lotte, Comox and Nanaimo basins; (2) a medial uplift comprising Vancouver Island and the Queen Charlotte Islands; and (3) a marginal shelf which is extremely narrow (Jess than 5 km) west of the Queen Charlotte Islands, widens to 160 km in Queen Charlotte Sound and is about 35 km wide west of Vancouver Island, where it is underlain by the Tofino sedimentary basin, with its• extension, the Juan de Fuca Basin, at the southern end.The medial uplift consists of a highly disturbed anticlinorium of mainly Mesozoic rocks, with a core of Palaeozoic. The rocks include thick sequences of eugeosynclinal volcanics and sediments. There is strati-graphical evidence of repeated interruption in sedi-mentation. By late Jurassic, the main eugeosynclinal phase was over and a successor basin was initiated in the interior' trough. This became filled, during Cre-taceous and Tertiary time, with sediments ranging in environment from bathyal turbidites to terrestrial conglomerates and coals. West of the medial uplift, another successor basin developed in early Tertiary times and became filled with mainly deep-water marine sediments. A third effusive sequence marks the base of the Tertiary on Graham Island and over most of the Hecate Strait region and Tofino Basin."

Jan 1, 1970

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By H. W. McGerrigle

The St. Lawrence Valley of Quebec lies in an earthquake danger zone, the main centers of which appear to be Murray Bay, Montreal and Quebec City. This paper compares conditions in this "earthquake zone" with those of other, currently more active, earthquake zones of the Earth, deals briefly with the mechanics of earth movements and outlines the means by which earthquakes are re-corded. An account is then given of the earthquakes which have occurred in the Province of Quebec -from that of 1534-35 to the earthquake of 1925. A 50-year frequency cycle is implied. The general conclusion is that the 11robability of future earthquakes should be given more consideration in the construction of buildings in the St. Lawrence Valley region.

Jan 1, 1966

By C. Tissot, R. Palmer

"Due to the low concentrations of gold, direct measurement of gold concentration in ore on belt has not been seriously considered to now. Pre-concentration or sorting strategies have largely consisted of particle sorting based on secondary characteristics such as colour, which can be successful in select cases. CSIRO has produced sample measurement results using gamma activation analysis of ~300 gm samples with accuracies of around 30 ppb at best. With this encouragement, a feasibility study into gold ore measurement on belt for the purpose of sorting pods of gold ore has been undertaken. The study described here included, prototype design options with existing industrial Linacs, extensive Monte Carlo modelling of measurement sensitivity and shielding, further sample measurement, a study of the interaction of target measurement accuracy and sorting efficiency, and a rough estimation of potential economic benefit. The projected model sensitivity of around 0.1-0.15 ppm (1 standard deviation) in 10 seconds for 1 ppm average feed result in good bulk sorting performance and intriguing economic potential.INTRODUCTION Pre-concentration or sorting strategies for gold ores have largely consisted of particle sorting based on secondary characteristics such as colour or density, which can be successful in select cases (Klein, 2010). No method is available to measure gold content for sorting in particles or even in bulk on belt, principally due to the low concentrations of gold present. In fact, in many cases it is difficult to do rapid bulk grade measurements of base metal ores with concentrations many orders of magnitude higher. By a fortunate quirk of nature gold is particularly amenable to gamma activation analysis (GAA). CSIRO has performed extensive work in GAA of samples of crushed ore (Tickner, 2017). This has resulted in the Photon AssayTM technique that is currently being commercialised through the CSIRO spinoff company Chrysos. The technique relies on the recent availability of industrial high intensity X-ray sources such as Linacs which are currently being used in industry for security, medical and sterilisation applications. This development has led to CRC ORE funding a feasibility study to determine whether on-belt measurement of gold concentration is possible at a rate and accuracy sufficient to be useful for bulk sorting, where pods of ore are diverted rather than individual rocks. The study in the first instance is based on Monte Carlo modelling that has successfully predicted the performance of the sample based gold measurements. As well as the measurement feasibility consideration was also given to the likely heterogeneity of gold ores and hence the degree to which useful separation could be achieved. This is then tied to a back of the envelope evaluation of the order of magnitude economics of bulk sorting in an example deposit."

Jan 1, 2017

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By Ahmad Ghahreman, Lin Li

"In this study, the Fe(II)/Fe(III) redox reaction kinetics on the surface of pyrite, have been investigated in a 0.5 mol L-1 sulfuric acid solution for a temperature range of 22 to 65°C. Based on mixed potential theory, chronoamperometry is introduced to study the Fe(II)/Fe(III) kinetics by subtracting the current density of pyrite oxidation in an iron-free acidic solution from that in an iron-containing solution at the same applied polarized potential. Tafel behavior was established by this method to analyze the kinetics of the Fe(II)/Fe(III) redox reactions. The results showed that exchange current densities increased slightly with temperature, however remained on the order of 10-5 A cm-2. The activation energy for Fe(II) oxidation and Fe(III) reduction on the pyrite surfaces was calculated to be 102.0 and 32.7 kJ mol-1, respectively. Anodic transfer coefficients also increased, from 0.24 to 0.39, with increasing temperature, which indicates a weakened n-type semiconductor property at higher temperatures. Electrochemical impedance spectroscopy measurements have indicated that at lower anodic over potentials the charge transfer is the rate determining step of pyrite oxidative dissolution in sulfuric acid solution. In the presence of Fe ions, the major contribution of the total current density comes from the Fe(II)/Fe(III) redox reaction. INTRODUCTION Pyrite, an abundant sulfides mineral in the nature, is commonly considered a valueless gangue mineral frequently associated with other valuable sulfide minerals such as chalcopyrite, or metals such as gold, or coal (Lin & Say, 1999). Pyrite oxidation has been the subject of extensive research in view of gold metallurgy, as oxidation of pyrite is the initial step to break down the pyrite lattice and expose the encapsulated fine gold particles (Gasparrini, 1983). Fe(III) ion and dissolved oxygen (DO) have generally been considered as the two most important oxidants with respect to pyrite oxidation, having been studied extensively in previous research (Zheng, Allen, & Bautista, 1986; King Jr & Lewis, 1980). The process of pyrite oxidation can be viewed as a series of reactions amongst pyrite, ferrous, ferric and oxygen in which pyrite is initially oxidized by the dissolved oxygen in water forming ferrous (Eq. 1), and then the ferrous also is oxidized by he dissolved oxygen to form ferric (Eq. 2). The ferric, produced by reaction 2, then could potentially oxidize pyrite (Eq. 3) and convert to ferrous."

Jan 1, 2017

By P. L. Drake

This paper comprises a discussion of the role which mineral resources will play in Canada&apos;s future export trade and the growing demand for minerals in Canada.

Jan 1, 1979