Search Documents

By M. Epiney, A. Ghahreman, R. Kim1and

"In the presence of sulfidic refractory ores, increasing the dissolved oxygen (DO) concentration can positively affect the gold leaching rate. To identify the role of DO in gold cyanidation, electrochemical behavior was studied in the presence of 3 different ores. Sample 1 was a low sulfide pyrite ore, contained 5.14% pyrite, 0.19% galena and 3.09% S. Sample 2 was a pyriticore as well, contained more sulfide as 8.35% S, and 12.4% of pyrite. Sample 3 was a tailing of silicate gold ore, still containing75 g/tAu, 0.13% Pb and 0.18% S. Gold cyanidation kinetics were studied by cyclic voltammetry (CV) and chronoamperometry tests. With sample 1, the gold oxidation peak current density from CV curve was increased to 1.38mA/cm2under oxygen injection, while it was only 0.66 mA/cm2with air injection. From chronoamperometry test, the reaction rate was also faster under oxygen injection. Sample 2 showed similar behavior with sample 1, but the gold oxidation peaks higher than sample 1, i.e. 1.75 and 2.27 mA/cm2, under air and oxygen injection, respectively. However, it seemed that the gold oxidation was impeded by sulfide ions for a longer period. In the presence of sample 3, the gold oxidation peak was the highest among three ores –2.75mA/cm2under oxygen injection, because of its lowest sulfide content. However, from chronoamperometry test, it was also shown that the gold oxidation was impeded because of a significant amount of Pb in the ore sample.INTRODUCTIONIt is well known that gold is leached under oxidative condition (Marsden &House, 2006). Through the most representative and oldest gold leaching technique, cyanidation, more than 90% of gold can be selectively leached from an ore. According to Elsner’s equation, gold is leached in cyanide solution by forming cyanide complex [Au (CN)2–], and oxygen is consumed as an oxidant(Eq. 1)."

Jan 1, 2017

By Edward Rybinski

Compañía Minera Antamina is a polymetallic mining complex that produces copper and zinc concentrates as primary products and molybdenum and lead/bismuth/silver concentrates as by-products. In 2007, Metso Process Technology and Innovation (PTI) was contracted to increase SAG mill throughput by integrating and optimising blast fragmentation, crushing and grinding for the harder M4/M4A (CuZn) ores. Following the implementation of recommendations provided by Metso PTI, the SAG mill throughput increased from 2750tph to reach an average of 3600tph for the remainder of 2007. Due to continued application of mine to mill integration and optimisation philosophy, by 2010, the concentrator consistently exceeded the target of 4400tph while processing harder CuZn ores.

Jan 1, 2012

By J. H. Reiss, D. F. Bruhn, Idaho National Laboratory, Y. Jiao, D. W. Reed, Y. Fujita, D. L. Daubaras

"Bioleaching offers a potential approach for recovery of rare earth elements (REE) from recyclable materials, such as fluorescent lamp phosphors or degraded industrial catalysts. Microorganisms were enriched from REE-containing ores and recyclable materials with the goal of identifying strains capable of extracting REE from solid materials. Over 100 heterotrophic microorganisms were isolated and screened for their ability to produce organic acids capable of leaching REE. The ten most promising isolates were most closely related to Pseudomonas, Acinetobacter and Talaromyces. Of the acids produced, gluconic acid appeared to be the most effective at leaching REE (yttrium, lanthanum, cerium, europium, and terbium) from retorted phosphor powders (RPP), fluidized cracking catalyst (FCC), and europium-doped yttrium oxide (YOEu). The Acinetobacter isolate, BH1, was the most capable strain and able to leach 33% of the total REE content from the FCC material. These results support the continuing evaluation of gluconic acid-producing microbes for large-scale REE recovery from recyclable materials.INTRODUCTIONAn enhanced recovery, substitute, reuse or recycle paradigm is important for balancing the supply and demand of critical materials (DOE, 2011). The recovery of rare earth elements (REE) from recyclable materials is an important component in this model. REE are used in a variety of modern products. For example, neodymium, europium, terbium, dysprosium, and yttrium are important for applications such as permanent magnets, lamp phosphors, rechargeable batteries, etc. (Binnemans, Jones, Blanpain, Van Gerven, Yang, Walton, & Buchert, 2013; DOE, 2011; Graedel, Harper, Nassar, & Reck, 2013). Cerium and lanthanum are used in glass polishers and additives in fluidized cracking catalysts (FCC)."

Jan 1, 2016

By Quenton Johnson, W. A. Gough, David Carr

"This paper describes the application of the BrainWave Model Predictive Controller (MPC) and Advanced Control Expert (ACE) Advanced Supervisory Control System on the SAG Mill, Ball Mill, and Rougher Flotation cells for a new gold processing line at the Oceana Gold - Haile Gold mine in Kershaw, South Carolina. For this project, ANDRITZ supplied the control system design and programming, operator-training simulator and advanced control. The advanced control was tested against the IDEAS™ dynamic simulator, and commissioned during the startup of the processing plant to help achieve target production as quickly as possible. Operators were able to run the equipment in a consistent and optimized manner from an early stage of the plant operation, increasing efficiency and profitability. MPC is able to reduce process variability beyond the best performance that can be obtained with conventional Proportional Integral Derivative (PID) control methods. MPC is able to optimize the control of processes that exhibit an integrating type response in combination with transport delays or variable interaction, which are characteristic of many gold processes including SAG mill weight control and Flotation cell froth level control. The experience and benefits of applying MPC during the startup of a new gold processing plant are presented in this paper.INTRODUCTION Mineral processing operations present many challenges for automatic process control due to variations in unmeasured ore properties, material transport delays, and non-linear response characteristics. Advanced process control technologies such as expert systems and multi-variable model predictive controllers are often used to improve the control of these processes to increase productivity and recovery efficiency. Typically these systems are applied after the mine has been in operation for a period of time. For this project, a complete dynamic process simulator was developed using the IDEAS platform for the purpose of training operators before the plant was constructed. Operators were able to become familiar with the process and the control system in order to become proficient in the use of the controls before the plant was ready to start. They were able to practice abnormal condition management including startup and shutdown of the process using the simulator and develop complete Standard Operating Procedures (SOPs) for these situations. The simulator was also used to test the control system functionality and operator Human Machine Interface (HMI) configuration to reduce errors and improve the performance of the control system during plant start-up."

Jan 1, 2017

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By W. Hawker, A. M. Ivana

"Pressure oxidation is used to liberate gold from refractory sulphide ore and concentrates with over fifteen autoclaves in operation. Despite the importance of pressure oxidation, the autoclave chemistry and chemical thermodynamics are not well established. For example, there is no consensus on aqueous iron speciation or stability of jarosite phases. Additionally, there remains questions about basic ferric sulphate formation and stability. In addition to a review of the current state of knowledge, a methodology to study the ferric precipitation reaction and relate the results to chemical thermodynamic predictions is presented which will be used to accurately define the phase boundaries of the iron precipitates in the future (hematite, jarosite and basic ferric sulphate).INTRODUCTION With declining availability of orebodies that respond to simple leaching conditions, pressure oxidation has become a prevalent technology to liberate gold locked in sulphide mineral matrices. Gold pressure oxidation was established 32 years ago, with McLaughlin being the first facility in 1985 (Thomas & Pearson, 2016). Pressure oxidation is carried out at elevated temperatures ranging from 180 to 240°C as shown in the summary of operations in Table 1 (Ruonala et al., 2016; Fleming, 2010).A considerable amount of research has been done to study iron solubility and precipitation under autoclave conditions (Tozawa & Sasaki, 1986; Umetsu et al., 1977; Sasaki et al., 1993; Fleuriault, 2016; Cheng & Demopoulos, 2004; Papangelakis et al., 1994; Yue et al., 2003). These reports provide a description of the process chemistry and iron behaviour in the autoclave. However, there remain questions about the type and stability of aqueous species and solid phases. This detailed information is required to build a robust chemical thermodynamic model of the system, allowing for equilibrium and kinetic reaction limitations to be discerned."

Jan 1, 2017

By C. Han, S. J. Zhou, Y. B. Shen, D. Z. Wei, P. Fang

"Collecting property of two hydroxamic acid collectors have different type of nonpolar structure to hemimorphite has been comparatively studied via monomineral flotation test, and the reason causes different collecting performance has been discussed from the view of relationship between molecular structure and collecting property. The flotation tests results show that C5-9 hydroxamic acid has an unbranched linear alkyl nonpolar group shows better collecting property to hemimorphite than cyclohexyl hydroxamic acid which has a naphthenic nonpolar group. FTIR detecting results show that the adsorption type of collector adsorbed on hemimorphite surface is chemical adsorption. Calculation results of polar group’s geometric structure parameters, polar group’s electron density distribution, octanol-water partition coefficient (logP) and molecular frontier orbital energy show that the key factor caused different collecting property of two collectors to hemimorphite is the logP; unbranched linear alkyl nonpolar group is more conducive than naphthenic nonpolar group to make hemimorphite particle more hydrophobic.INTRODUCTIONZinc-bearing mineral recovered from lead-zinc ores is the main source that people can obtain zinc resource from nature. However, natural sulfide ores are currently getting depleted steadily for the primary zinc source. In order to satisfy the future demand of zinc resource, there is an obvious recognition that the recovery of zinc oxidized minerals from the ores is a crucial alternative (Hosseini & Forssberg, 2007; Navidi Kashani & Rashchi, 2008).But the fact that can’t be ignored is the flotation of zinc oxidized minerals is much more difficult than that of zinc sulfide minerals, which is mainly due to the flotation characteristics of these zinc oxidized minerals such as lower selectivity and higher reagent consumption, as well as complex and variety of lead-zinc ores. Presently, there have been many various beneficiation technologies used for recovering zinc oxidized minerals and dealing with ores for recovering metallic zinc such as flotation and hydrometallurgy (Abkhoshk, Jorjani, Al-Harahsheh, Rashchi, & Naazeri, 2014; Önal et al., 2005). But from an overall perspective, flotation is the most common method used for the beneficiation of zinc oxidized minerals, and there have been extensive investigations conducted on the flotation of zinc oxide ores (Ejtemaei, Gharabaghi, & Irannajad, 2014). Until now, the most well-known method used commercially for the flotation of zinc oxidized minerals is sulfidization with sodium sulfide and flotation with a cationic collector of amines containing from 8 to 18 carbon atoms. However, a major problem for this method is the large amount of fines and slime results in the increase of reagent consumption and promotes the phenomenon of slime-coating. For preclude this negative effect, the de-sliming and processing optimization is indispensible (Peres, Borges, & Galery, 1994; Salum, de Araujo, & Peres, 1992)."

Jan 1, 2016

By Sylvain Picard

"RESUMELe gisement Silidor représente la dernière découverte effectuée dans le camp minier de Rouyn-noranda (fin 1985). Située à 5 km à I' ouest-nord-ouest de Rouyn-Noranda, ce gisement aurifère doit être mis en exploitation au cours du mois d’avril 1990. 11 est constitué par plusieurs facies minéralises comprenant une tonalité, un dyke mafique, une brèche carbonatée et par une veine de quartz. L’or se présente en particules très fines associées ou non à la pyrite. La zone d’altération hematitisee se développe sur une largeur de 30m environ de chaque cote de la veine. Une première étude structurale montre que la minéralisation s’est mise en place le long d’une zone de tension, orientée NNW, résultant de I' interaction de deux zones de cisaillement dextre orientées N270° et N300°. Les réserves diluées sont évaluées jusqu’ à 700 m de profondeur, à 4,78 Mt à 5,4 g/t Au. ABSTRACTThe Silidor ore deposit, located 5km WNW of Rouyn-Noranda, is the latest discovery made in the Rouyn-Noranda mining camp. Discovered at the end of 1985, this gold deposit will begin production in the spring of 1990. The deposit comprises several facies including a tonalite, a mafic dyke, a carbonated breccia and quartz vein. Gold is present as very fine grains, associated or not with pyrite. A 30m wide hematized alteration zone is developed on both sides of the structure. A structural analysis shows that the mineralization took place along a NNW oriented tension zone that resulted from the interaction of two dextral shear zones, oriented N270 and N300 respectively. The diluted ore reserves are estimated at4,78 Mt at 5,4 g/t down to a depth of 700m."

Jan 1, 1990

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By S McQuitty

The metallurgical treatment of Falconbridge ore re-quires an extremely fine grind of the pyrrhotite portion ? for maximum liberation and recovery of nickel. This paper describes the operation of a grate discharge pebble mill in closed circuit with cyclones regrinding 25 to 30 tons per hour of sulphides to approximately 90 per cent minus 325 mesh. The consumption of the screened ore grinding medium is of the order of 2.5 pounds per kw.-hour, or less than 1 per cent of the tonnage of re-ground sulphides. IN RECENT years, there has been a considerable interest in pebble grinding in the uranium industry, and a number of installations have appeared. However, the use of sulphide ore pebbles as a grinding medium has so far been relatively limited. There has also been some question as to their suitability for the very fine grinding of sulphide concentrates. This paper describes the preliminary results of a commercial operation involving the

Jan 1, 1964

By J. Awmack, M. A. Tomlinson, P. J. Lind

"Peñasquito is a complex polymetallic deposit containing gold, silver, lead, zinc, and copper and is one of the largest producers of gold in Mexico. Mining activity is currently transitioning to a second open pit, Chile Colorado, which will be mined concurrently with the existing open pit, Peñasco. The ore bodies are located within diatreme pipes and into the surrounding sediment formation. In the coming years, mining will be carried out in more sedimentary zones, which are significantly higher in organic carbon content. Organic carbon in the feed influences both flotation and leaching operations. Several changes are being implemented to the Peñasquito flowsheet to mitigate the effects of increased organic carbon in the plant feed. These include the use of alternate reagent schemes, construction of a carbon pre-flotation circuit, implementation of a pre-leach flotation circuit ahead of pyrite leach, and evaluation of a tertiary process for separation of carbon and precious metal minerals.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas in the Mazapil municipality (Figure 1). Peñasquito has been in operation since 2009, with mining carried out by open-pit methods. Oxide ore has been processed in a heap leach facility and sulfide ore is treated in the sulfide processing plant. The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 465,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead in lead concentrate, and 263 million lb of contained zinc in zinc concentrate (Goldcorp Inc., 2017). To recover more of the contained gold and silver and to mitigate the impact of increasing organic carbon content in the ore, a number of significant changes are being made to the operation."

Jan 1, 2018

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By N. H. Grace

"IntroductionA STRIKING FEATURE of the past twenty years has been the application of organized scientific and industrial research to problems of national defence and security and to the development of our natural resources. It has been shown that effective research improves public health, increases the productivity of land, makes mineral wealth available, and increases the efficiency and productive capacity of industry. Alberta is a region bounteously provided with a variety of natural resources, and the Province has entered into a period of unprecedented industrial development. There is, surely, a great opportunity to bring scientific research to bear •on problems associated with the development of these natural resources.I propose to spend a little time discussing the term 'research', indicating something of the various types of research and those fields which appear to •be the particular responsibility of government bodies. It seems logical, also, to outline the course of development .of industrial and scientific research in the English-speaking world during the past twenty-odd years.Research is investigation, examination, or enquiry, and involves the application of human thought, and actions, to the unfolding of new knowledge. That knowledge may assume a variety of forms. Fundamental knowledge may be new facts related to some form of matter, to motion, space, thought, and so on. Those engaged in applying the natural sciences have no monopoly on research as this term is equally valid for those engaged in obtaining, sorting, relating, and interpreting the facts of history, literature."

Jan 1, 1952

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By R. K. Carnochan

MANY improvements have been made in recent years in the milling of industrial minerals and it is the purpose of this paper to review some of the more important innovations that are now being used in the preparation of these products. Some of the observations which will be made have been prompted by what was seen on a recent trip to industrial mineral milling plants in the north and central sections of the eastern United States. The flotation plants visited were those of the Valley Forge Cement Company at West Conshohocken, Pa., the International Agricultural Corporation at Mount Pleasant, Tenn., and the Aluminum Ore Company at Rosiclare, Ill. Besides these, sand plants in Pennsylvania, West Virginia, and Ohio, coal-cleaning plants in Pennsylvania, pyrophyllite, mica, feldspar, clay, and kyanite plants in North Carolina, and a zinc mill and the Tennessee Valley Authority ceramic laboratory in Tennessee were visited. The milling of industrial minerals can be considered under three broad headings, namely, crushing, grinding, and purification. Usually there is both a separation and grinding problem in treating an industrial mineral, but the problems are distinct, although sometimes a separation is made while grinding, as in the case of a Raymond throw-out mill, which grinds and at the same time throws out most of any hard material present in its feed.

Jan 1, 1939

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By J. Ga?parík

The optimal selection of machine or machine group for building processes is very important role of building planner during the process of building planning. During this process building planner have to analyze several factors influencing the final effective decision concerning this problem. There are several factors and criteria for effective selection of building machines. In our contribution there are analyzed: ability of machines to realize designed building process (quality aspect), duration of mechanized process (time aspect) and minimizing of energy consumption (cost and environmental aspect). Selected scientific methods and theories of problem solution can be divided into these groups: theory of system (creation of building machine selection method), multi-criteria optimizing method (analysis of mechanized building process from the point of more optimal criteria), queuing theory (application during the mathematical modeling of mechanized soil processes), method of scientific analysis (analysis of factors influencing final decisions), method of scientific synthesis (creation of optimizing method implemented into building processes and possible application in construction sector). Multi-criteria optimizing method were during our research work implemented into soil processes and selected building group machines (excavators and trucks), which are very often used in construction and mining processes. This method can be considered as a multi-level decision making process based on multiple parameters. In our contribution is presented key mathematical models for model example solution and software built in Java, which has been created as a support for method described in this contribution. Application of this method and software will increase the effectiveness of building machine selection from the point of key criteria of optimizing: quality, time and energy consumption.

Aug 1, 2013

By H. C. Cooke

"This paper has reference in a general way to the region extending from the north shore of lake Buron to the northern limit of the elliptical-shaped area generally known as the Sudbury Basin, and more especially to the district lying south of the Basin (Fig. 3). Attention is concentrated mainly on the structure of the district and, as space does not permit of much geological description, it is assumed that the reader has some knowledge of the general geology. The accompanying table outlines the sequence of the rock formations according to the most recent available information; for further details the interested reader may consult the publications of the various authors mentioned in the paper.STRUCTURE OF THE SEDIMENTARY ROCKS SOUTH OF THE SUDBURY IRRUPTIVEThe rocks south of the Sudbury irruptive, excluding certain intrusives, are, in order from north to south:(1) A band of basic lavas.(2) A band of well-bedded greywackes and quartzites, long termed the McKim greywacke.(3) The Copper Cliff formation, with McKim greywacke' both to the north and south.(4) The Ramsay Lake conglomerate.(5) A thick quartzite formation.All these rocks strike approximately east-northeast, dip steeply south, and generally face south, though there are local exceptions."

Jan 1, 1954