Search Documents

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By Kurt D. Mitchell

"This paper discusses general application for A C variable frequency drives in the mining industry. A review of induction motors characteristics, adjustable frequency controller fundamentals, and three commonly used controllers is presented. General application guidelines for the three different types of controllers; variable voltage input , current source input and pulse width modulated are then reviewed in detail, and an example of the economic benefit of this technology is discussed. IntroductionSoon after static DC variable speed drives were well established in industry, a need for static AC variable speed drives was seen. The first technical papers describing possible systems appeared in the mid-1960s, with commercially available units arriving in the early 1970s. Without exception, static AC drives are substantially more complex than their DC counterparts, but they have some very desirable properties. As compared to DC motors, AC motors are less costly, physically smaller, more reliable, require less maintenance , easily sealed, have good load regulation, are able to run at higher operating voltages, and have little danger of over-speed runaway . These properties are particularly desirable in explosion-proof, submersible or difficult accessibility applications.Variable speed AC drives are now a proven technology. available in packages from Sub-horsepower to hundreds of horsepower, from 115VAC to 4160 VAC. This paper covers the principles of operation of three common types of controllers, application criteria, motor consideration and finally an example of how an AC variable speed drive can pay for itself in terms of energy savings."

Jan 1, 1986

By Olaf Kessler, Jan Kalich, Michael Reich, Julia Osten, Uwe Füssel

Modern automobile bodies consist of different materials, e.g. aluminium alloys and high strength steels. Mechanical joining, e.g. clinching, is very suitable for joining aluminium and steel sheet. But clinching needs a sufficient ductility, which is no longer supplied by high strength steels. Laser-assisted clinching has been shown, to be able to join aluminium and high strength steel sheet successfully. Thereby the steel sheets were heated locally for short times to increase their ductility. Due to the thermal contact between steel and aluminium sheet the aluminium alloys also achieve a local short-time heat treatment. This fact may cause a significant impact, as aluminium sheet in automobile bodies is often used in T4 (or similar) condition and later artificially aged during the paint bake cycle. Aluminium alloys 6016 and 6181 have been short-time heat treated with heating rates up to some 100 K/s. Precipitation and dissolution processes have been monitored in-situ by calorimetry. Mechanical properties have been investigated on as well as after short-time heat treatment by deformation dilatometry. The results show, that suitable short-time annealing parameters during laser-assisted clinching can increase ductility and at the same time act as retrogression for aluminium sheets, resulting in increased strength after aging.

Jan 1, 2015

By Christopher R. Davis

Resource modelling is the basis for any economic appraisal of a mining project and includes a number of steps from data acquisition and validation to resource reporting and classification. At each step in the modelling process it is necessary to define the specific objectives, the methodology proposed to achieve those objectives and to establish a set of checks and validation tools to assess the effectiveness of the proposed methodology. The data used has to be both reliable and relevant for the purpose of the modelling. QA/QC for database validation requires verification of sample location; including correct collar location, topographic modelling and down-hole surveying. Validation is also performed on assaying information such as checks for sampling bias and accuracy of core splits, proper use of pulp duplicates and standards, handling of calculated values, explicit/implicit absent data and data entry errors. The second step involves identifying the mineralized domains resulting from the mineralization process. This step requires a geometric interpretation of all relevant geological features that have influenced the spatial distribution of the mineralization including dykes, faults and alteration. In addition, a geologic reference system rather than a standard Cartesian system is established to measure distances between samples. Once the mineralized domains are established and the database has been validated, statistical and spatial description of the mineralized samples are examined in order to establish the histogram and the variogram of all variables of interest and their correlation. Results are also used to calibrate the global resource estimate within the mineralized domain and to establish the search strategy for grade interpolation. The mineral envelope is filled with polyhedral cells representing mining blocks. The average grade of these blocks is estimated using kriging techniques in order to eliminate global bias and to minimize the local error in the block grade estimate. Visual checks are made to validate the spatial trends in grade distribution while global bias and smoothing effect are assessed from the declustered sample statistics. When required, smoothing correction may be applied using ?change of support? techniques. Simulations are used to perform sensitivity analysis and the simulation models are used if severe smoothing of spatial variability makes the interpolated model inappropriate for mine planning. The keys to successful resource estimation are an integrated team of geologists, geophysicists, geostatisticians and mine engineers using the best available technology and reviews by independent auditors. The resource team is also responsible for performing a QA/QC program in order to measure the effectiveness of the methods in meeting the specific objectives at each step of the modelling process.

May 1, 2001

By Gerhard Kircbner, Boen Tan

"IntroductionThe Key Lake uranium-nickel ore deposits are located in the Athabasca Basin of northern Saskatchewan, Canada (Fig. 1). Many papers have been published on Key Lake in the past (Dahlkarnp and Tan, 1977; Kirchner and Tan, 1977; Kirchner et al., 1980). Immediately after its incorporation in 1968, Uranerzbergbau GmbH, a German holding company, set up exploration subsidiaries in Australia, the United States and Canada. This account reviews those exciting years starting with the concept to explore the rim of the Athabasca Basin in Saskatchewan, and leading up to the discovery of the deposits in 1975 and 1976.A few summary statements can be made:• The discovery of Key Lake resulted from a very systematic exploration approach and the persistence of Uranerz, the operator. • Cluff Lake and Rabbit Lake had been discovered some seven years before, but it was the discovery of the Key Lake deposits which brought Saskatchewan to the forefront to become Canada's foremost uranium producing province.• The experiences gained at Key Lake, which were subsequently published, triggered the discovery of many other deposits of similar, or even larger, size than Key Lake. The spatial relationship of those deposits to graphitic conductors and hydrothermal alteration zones are presently the most effective indicators for locating new deposits - indicators which were first recognized at Key Lake.• Key Lake is, and will remain for some years to come, the largest producing high-grade uranium mine in the world."

Jan 1, 1994

By William H. Pomroy, Kenneth E. Hjelmstad

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. A fire emergency plan includes a means of warning miners of the existence of a fire, and the need to evacuate or retreat to a place of refuge. The warning alarm must be fast and must reach all miners, regardless of their location or work activity. Means of fire warning are varied, and include such methods as stench, flashing lights, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. Stench can be slow and seldom achieves total mine coverage, especially in high-back room-and-pillar mines with low ventilation velocity. Telephones are effective only where personnel are close enough to hear the phone ring. A novel fire warning alarm system has been developed by the U.S. Bureau of Mines which enables instantaneous warning of all underground personnel. The warning alarm is sent by an electromagnetic signal which penetrates through mine rock from a transmitter to small person-wearable receivers. Each miner's cap lamp battery could be equipped with a small receiver and when a fire or other emergency occurs the miner could be alerted to the danger by a blinking of the cap lamp. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This paper describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, design of the prototype transmitter and receiver, test results, and status of commercial development of systems utilizing this technology.

Jan 1, 1994

By N. A. McPherson, P. C. Stevens, A. J. Rigby

"There has been a consistent move in recent years to continuously cast small billets while utilizing ceramic stream protection between tundish and mould. The need to have ceramic stream protection has developed from a need to improve billet surface quality by submerged pouring. The need to protect the ladle to tundish stream in conjunction with tundish to mould protection is explained.The continuous casting of thin slabs is at the development state and will require a great deal of ceramic development to ensure the economic viability of the project. An insight is given to the main problems.IntroductionDuring the early development period o f the continuous casting of steel in the late 1940s and 1950s, much of the work was carried out on small cross section products. For example, the continuous casting of 50 mm square billets was carried out on a production scale in the United Kingdom at Barrow. Slab casting was initiated on a production basis on 100 mm thick stainless steel slabs at Atlas Steel, Weiland, Ontario. In the case of slab casting the thickness increased gradually until it was similar to Slabbing Mill feedstock , i.e. in the range 200 mm to 250 mm , although stainless steel continued to be lower at around 185 mm thick.For billets , a significant proportion of steel is now cast at around 100 mm square which creates specific difficulties when casting with a submerged pour - mould powder practice. The move back to smaller cross sections is further emphasized by the current interest in "" Near Net Shape Casting"" . If this move continues, then significant development will be required to create the refractories used between tundish and mould in the continuous casting process.Two specific areas which will receive attention are; (I) the casting of small cross section billet s; and (2) the casting of thin slab."

Jan 1, 1990

By T. M. Siew

"This paper begins with a brief discussion of the geology of the Newfoundland Zinc Mine area. The results of groundwater studies and pumping tests are then presented. It was decided that groundwater in the mine could best be controlled by conventional sump pumping and grouting. The system is fully described, as well as plans for improvements on the method. LocationThe Newfoundland Zinc Mine is located in the Great Northern Peninsula of Newfoundland, six miles northeast of Daniel's Harbour. The mine is situated at an elevation of approximately 350 feet above sea level, 5 miles farther inland , west of the long range of mountains which rise abruptly with elevations of over 2,000 feet above sea level.GeologyThe ore deposits occur in lower Ordovician carbonate rocks that form part of the stable St. Lawrence platform, which is mainly composed of (1) the lower Cambrian Labrador group, (2) the upper Cambrian to lower Ordovician St. George group, (3) the disconformity overlying Middle Ordovician limestones and shales of the Table Head formation and, (4) two overlying klippen composed of Cambrian and lower Ordovician rocks.The ore deposit is a Mississippi Valley type of the Tennessee variety, having proven are reserves of 5.3 million tons averaging 9.70/0 zinc from eleven ore zones which exist in an area of 5.5 square miles.Among these ore zones, the L zone is the major underground mining area, and is by far the largest of the known deposits. It has proven are reserves of 3.4 million tons with 11.5% zinc; this underground development has been inprogress since 1974.Stratigraphically, the orebody, which occurs about 300 feet below the disconformities between the Table Head and St. George formations, is situated in the upper St. George formationof lower Ordovician age.The upper St. George formation of the L zone is divided into three main units (Fig . I) : the underlying lower limestone the middle grey dolomite pseudo breccia unit and the overlying siliceous dolomite unit. In this area of the mine, the beds of the St. George formation dip gently west to northwest to 10 to 15 degrees. The orebody, which is generally strata controlled with a southwesterly plunge and which has the form of thin, narrow, but elongate, en-echelon ore bed s, is contained in grey dolomite pseudo breccia. Its dimensions vary from 50 to 900 feet in width and 8 to 120 feet in thickness, and the over-alllength exceed s 6,000 feet.The surficial deposit of the area is a till comprising a heterogeneous mixture of sand, gravel, cobbles and boulders, with an average depth of 20 feet."

Jan 1, 1980

By Wenbin Zhang, George W. Poling

"Prior or simultaneous addition of ammonium sulphate can, not only enhance the activating effect of hydrosulphide ions on xanthate flotation of malachite but it can also eliminate possible detrimental or depressing effects of excess residual hydrosulphide . Use of relatively inexpensive ammonium sulphate appears to reduce the consumption of the much more expensive sulphidizing agent for optimal flotation recovery INTRODUCTIONOxidized copper minerals float poorly with conventional thiol-type collectors. This is believed to be due to the nonadherent character of the collector coating, which is readily re- moved by particle abrasion. Rosas and Polingr reported emulsion flotation seemed capable of resisting abrasion during the flotation of non-sulphide copper ores. It appears that the most common flotation technique for oxidized copper minerals comprises sulphidization with Na .S and subsequent treatment by sulphydryl collector. The principles of this method are available . Malghan recently reviewed the studies on the role of sodium sulphide in the flotation of oxidized copper, lead and zinc minerals.It is well known that in the sulphidized flotation of malachite, the activation process depends strongly on the concentration of the sulphidizing agent, i.e., insufficient sulphide gives poor recoveries because of inadequate sulphidization; excessive sulphide also causes poor recoveries due to the depressive effect of the residual hydro-sulphide ions in solution. A major difficulty in sulphidization, especially with a varying feed nature, is to establish and maintain the optimum sulphide concentration in solution. In plant practice, vigorous control of sodium sulphide is required and stepwise addition of the reagent is recommended to improve the efficiency of the process. Soto and Laskowskim have found that malachite, depressed by an excess of sulphide ions, can restore its floatability if air or oxygen is introduced to the pulp. They attributed this to the oxidation of the HS - ions on the surface of the mineral. Jones and Woodcockuvi showed that a sulphide ion selective electrode could be used to optimize the conditions (e.g . amount of hydrosulphide, sulphidization time, flotation time) more readily and precisely than existing methods in the flotation of oxidized copper ores."

Jan 1, 1989

By V. Schenk

Dust exposure resulting from the exploitation and winning of natural resources below ground has presented a serious health problem since the beginning of mining. The boom phase of the German hard coal mining industry after World War II with at times up to 500,000 employees saw an increase of dust exposure of miners below ground as the mechanization of road heading and mining increased significantly. More and more miners were diagnosed with coal-workers-pneumoconiosis (CWP), a chronic and irreversible lung disease resulting in a significant impairment of pulmonary function. This realization led to a reduction of CWP in the German hard coal mining industry in the 1960s. The successful fight against CWP began with the introduction of technical dust prevention measures. By infusing the coal seam with water before mining, sprinkling and spraying of heading and mining machines as well as canopies with water, aspiration in places with high amounts of dust and the suppression of dust with chemical substances it is possible to significantly reduce the miners? dust exposure. All operating points below ground are checked and measured regularly with regard to dust exposure. Through the combination of these values together with the individual shift data a relatively precise profile of individual dust exposure can be obtained. This profile allows the targeted work assignment when certain predetermined limits have been reached, moving the miner to a work place with less dust exposure and thus reducing the chronic dust exposure. The state of health of the individual is known because since about 60 years ago extensive occupational health checks have been carried out regularly at least every two years which means that work restrictions can be imposed depending on the findings. Since the beginning of the 1980s more value has been attached to not only situational but also behavioral prevention. Given the comprehensive provision of protective masks, having a protective effect as well as the required comfort when being worn, each miner has the opportunity to protect his respiratory organs depending on the specific dust exposure. Through a combination of all these measures the German hard coal mining industry has succeeded in beating the classic coal miner?s disease CWP. For mines in the Ruhr valley this means that a miner who started work after 1978 will no longer develop CWP.

Aug 1, 2013

By D. Crone, T. Watts

"The Lindsley project was a program of deep drilling to test the contact down-dip from two nickel-copper deposits, one uneconomical and the other mined out. The role of Borehole Pulse EM(PEM) was to detect the higher grade, more massive sulphide zones if they were missed by a drillhole, and to help determine geometry if the zones were intersected. Two problems appeared as the PEM survey progressed: (1) conductivity-thickness as measured by the PEM did not always relate to economic sulphides as determined by the market; (2) a pattern of unusual PEM anomalies was obtained that indicated something odd and big, but the cause was unknown. A large fold structure subsequently was indicated by a program of deepening previous holes, the third of which intersected high-grade mineralization below 1280 m. Falconbridge is in the process of shaft sinking and underground exploration.IntroductionThe Falconbridge Lindsley property is on the south rim of the Sudbury basin, 8 Ian north of downtown Sudbury. The original property was acquired by a prospector named James Stobie, who, in early August 1885, staked a showing that later became the Mount Nickel mine (Fig. I). On August 10 Stobie staked another property that would become the Little Stobie mine, and at the end of the same month he staked the main Stobie orebody.In 1888, the ground immediately west of the MOlU1t Nickel find was staked. This ground contained the Blezard deposit (Fig. 1) which was put into production in 1889 and was eventually acquired by Inco. Down-dip from the Blezard workings, on Falconbridge ground, is located the upper Lindsley No. 1 deposit which was drilled off by Falconbridge in the 1940s to 1950s. A decision to go underground on the Lindsley No.1 mineralization was made in 1969, but the project was cancelled in 1971 because of declining nickel prices. The shaft was stopped at 95 m, and the headframe and hoist were sold. Further surface exploration drilling in the 1970s discovered the deeper Lindsley No. 2 zone, but as it had grades similar to those of the No. 1 zone, it too was considered uneconomic."

Jan 1, 1992

By Simon Houlding

"Part 1 (CIM Bulletin, August 1991) of this article identified the limitations of the traditional modelling methods and demonstrated the approximations and errors introduced by their application to complex mining situations. The objective of Part 2 is to describe the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods. Limitations of the Traditional MethodsThe limitations of the traditional modelling method s (viz. simple block modelling, gridded modelling and their more recent variations) were discussed in detail in Part I . These methods are all based on the use of rectangular discretization to represent the boundaries and volumes of ore deposits and mining excavations. As a result they are unsuited to the representation of nonrectangular geological complexities such as folding, faulting and irregular surfaces . They are equally unsuited to the representation of realistic excavation limits, particularly in the case of underground mining.Recently these methods, with limited variations in technique, have been applied to increasingly more complex geological and mining situations. The resulting potentials for error and conflict within the modelling pro cess were demon strated in Part I . The effects can be summarized as follows:• volume and boundary approximations introduced by therepresentation of irregular three-dimensional boundaries andvolumes by rectangular modelling elements ; • geostatistical errors and conflicts caused by neglect of the relationships between grade estimates and the geometric/ spatial aspects of irregular volumes and associated observations (samples), including an inability to produce precise estimates with meaningful confidence limits;• a compounding of these effects by using rectangular element sizes other than the geostatistical optimum, and by using differentelement sizes within a model; and• general inefficiencies introduced throughout the modelling pro cess by the requirement to represent geology, grade distribution and excavation limits with a singular modelling method and model."

Jan 1, 1991

By T. G. Carter

"During the early part of the 1980s, four new surface coal mines commenced operation in the Province of British Columbia. Each represented a major investment in both persons and materials in order to protect this investment in one significant area-the fixed portion of the surface coal handling system-a substantial amount of work was undertaken to ensure that the system was well protected from an outbreak of fire. A great deal of effort in this field had already been made by those coal mines which had been in operation for a number of years and experience gained at these operations was utilized in determining the level and extent of fire protection for the new mines.This paper summarizes the major problems, and suggests some of the methods of solution, in providing an adequate degree of fire protection for surface coal handling systems. It will also discuss the potential for gas and dust explosions together with ways to minimize this potential.The Fixed Coal Handling SystemNote: The word ""fixed"" has been used in its present context to denote that part of the coal handling system where the coal is moved via fixed installations such as a conveyor. It differentiates from that part of the system where coal is moved by mobile equipment.The raw coal delivered to the truck dump will undergo two major processes on its way to the rail load out. The first will be at the coal preparation plant where coal of specified quality will be extracted from the raw feed to the plant. If this coal is of metallurgical quality, and sometimes if it is of thermal quality, it will pass through a thermal dryer where part of the moisture acquired during coal preparation will be removed, i.e. the second process. As the complexity of both the coal preparation plant and the thermal dryer is such as to warrant separate considerations they will not form part of this paper. Each of the processes, however, is generally, housed in its own building, thus, containment of any hazards is usually more attainable than those existing or caused in the rest of the system."

Jan 1, 1988

? Introduction ? Partenariat MRNF - MAE ? Goldex ? Manitou : - Ré-aménagement du bassin versant - Accès aux zones problématiques - Filtration du ruisseau pour les travaux - Nettoyage près de la rivière - Régulation du débit et bassin - Digues et bassins - Déposition résidus Goldex ? Chemins d?accès Goldex-Manitou ? Pipelines: Goldex ? Retour Goldex ? Manitou ? Station de pompage ? Résumé

Feb 1, 2008

By Alan Galley, Tom Hynes, Michel Plouffe

"Mining in Canada’s economy• Employs 320,000+ workers; Wages 30-60% above other sectors• Operates 220 producing mines, 33 smelters and refineries• Paid $8.4B in taxes and royalties to governments in 2010• Invests about $30B in capital projects annually • Largest private employer of Aboriginal Canadians 2• Core supplier to clean-technology sectors• Attracted 18% of world exploration spending in 2010• Efficient TSX processes - 1400 mining companies listed, ~50% of mineral projects are outside Canada• Estimated 1000 Canadian companies in 100 countries• Minerals account for 21% by value of Canada’s goods exports• Top 5 World Producer in uranium, potash, nickel, platinum, aluminum, diamonds, zinc, met coal"

Jan 1, 2012

By S. W. Brooksbank, R. A. Benkis

"IntroductionThe Republic of Indonesia is a developing Southeast Asian country that unites the Indian and Pacific oceans, and spreads across nearly 14000 islands with a total land area of about two million km-. The distance across the country approximates the distance across Canada: Indonesia extends for more than 6000 km from the northern tip of Sumatra to the eastern border of Irian Jaya in the middle of New Guinea. With a population of around 180million, Indonesia is one of the world's most populous countries. A mix of 366 ethnic groups populates the country and there are some 250 distinct languages spoken. The topography of Indonesia generally is quite rugged because of its numerous volcanos. For example, the island of Java has 121 volcanos, of which 15 rise above 3000 m and another 44 reach heights between 2000 m and 3000 m.Indonesia has a diversified resource base, with plentiful energy resources (coal, oil, gas and hydroelectric), significant mineral deposits, large timber potential and a developed system of agricultural commodity production and export. A high proportion of the primary resources are on the sparsely populated islands of Sumatra and Kalimantan, whereas 7'3 of Indonesia's people reside on Java, or on 70/0 of the country's land area. Around Jakarta in western Java the population density is around 8000 per krn2. This contrasts with less than nine people per km- on Sulawesi (Fig. I)."

Jan 1, 1992

By D. Raicevic

After more than 93% of the uranium is extracted from Elliot Lake uranium ores by a sulphuric acid leaching process, the leach residue (tailings) contains small amounts of uranium and radioactive isotopes, particularly radium-226, which is the most serious health hazard. Heavy metal components and pyrite are also present, along with the gangue minerals. Currently, over /000 acres of the Elliot Lake area are covered with these tailings, which contain over five million tons of pyrite. Because of constant oxidation of the pyrite by bacteria (thiobacillus) and the presence of moisture, pyrite slowly generates sulphuric acid, which steadily leaches the metal-bearing constituents from the tailings. The seepage-flows of the dissolved contaminants, although often quite low in volume, have an environmental impact on the Elliot Lake area. Although these seepages are treated and most of the contaminants removed and impounded, a small amount of the radioactive contaminants reaches Lake Huron via the Serpent River. This paper describes a flotation approach for treatment of the Elliot Lake uranium tailings to produce new, decontaminated tailings practically free of pyrite, with radium, thorium and uranium contents considerably reduced. The decontaminated tailing produced, which comprises about 75% by weight of the current uranium tailings, appears to be suitable for mine backfill. Because mine backfilling normally uses about 50% of the plant tailings, the surface storage of about half of the uranium tailings, therefore, would be eliminated by this process. Mine backfilling would also increase the mine production and thus enlarge the over-all uranium resources due to recovery of the ore from pillars. The pyrite concentrate produced from the current uranium tailings would be suitable for sulphuric acid production. The possibility of uranium recovery, and disposal of radium and thorium from the concentrates produced, is now being studied at CANMET.

Jan 1, 1979

By Robert B. Parsons

"A study recently completed by the Prospectors and Developers Association, assisted by the author and computerized mine models he developed, presents a strong case that present tax rules severely handicap the junior exploration company relative to the established producer. This month, Tax Notes briefly summarizes the highlights of the study and some of the Association's ideas which came out of the study.IntroductionIn the case of any industry, a particular project or investment will generally generate a more attractive after-tax rate of return to a tax paying entity than to a non-tax paying entity: the ability to shelter current taxable income with tax deductions related to the project or investment can present a definite advantage as compared to shielding taxable income in the future with the same deductions. But, this advantage is probably seen nowhere more clearly than in the mining industry where the tax rules allow for substantial up-front write-off's. Studies show that the junior mining company which is earning no taxable income currently can be seriously disadvantaged, compared to the mining company which is currently generating taxable profit and paying taxes. This is particularly disturbing when one considers the importance of the junior segment of the mining industry. One might well ask where the equity is, in a tax system which causes the junior company to look at a deposit and see rock in the ground, when at the same time the deposit represents a viable mine to an operating company. This inequity and the importance of the junior mining company have been recognized to some extent in the income tax legislation. In recent years, the expansion of the rules for deducting certain earned depletion allowances against any source of income, and changes to improve the flow-through share rules, have gone part way in helping to put the junior on a more equal footing with the operating company. But it is questionable whether or not these helpful changes to the tax rules have done enough to alleviate the apparent inequities in the income tax legislation."

Jan 1, 1985

By Gerhard Heinrich

"The composition and the possible utilization of a slag sample from a nickel smelter operation in the Sudbury district were investigated. The sample containing 0.136% Ni, 0.10% Co and 0.29% Cu could be characterized as a fayalit e slag with a sulphide bearing glass matrix. While the fayalite contains most of the Co, Ni is enriched within both sulphides and fayalite. Cu is only present in higher amounts in sulphides or metallic droplets. This, as well as the small grain sizes of the mineral phases, inhibits significant enrichment by mechanical methods. However preconcentration is possible by means of magnetic separation. An effective hydro metallurgical approach proved to be oxygen pressure leaching with sulphuric acid. Accordingly, the method proposed for processing the investigated slags is to combine the normal utilization as coarse construction material with pressure leaching of the fines and the ground upgraded magnetic fraction. Besides the recovery of base metals, the leaching process yields fine-grained residues, which, after addition of CaD, will set to a cement-like material, or can be used as a pozzolanic cement colour. INTRODUCTIONDuring the pyro metallurgical processing of nickel ores, the valuable metals nickel, cobalt and copper are enriched within the sulphide matte, similar to the smelting of copper ores. The resulting waste materials are slags, which may still contain valuable metal contents of up to 0.5% or above . These contents are close to the cut-off grades of some nickel-cop per-cobalt deposits. The methods that are used to recover copper from slags comprise in general further pyro metallurgical treatment, often after enrichment by flotation. Another area of application for such slags is their use as construction material. However, this might cause environmental problems if nickel containing dusts are produced.Based on one example, the characerization and a possible way of complete utilization of nickel smelter slag s as construction materials in combination with partial base metal recovery are described in this paper. The investigated slag sample was obtained from a dump site in the Sudbury district, Ontario. Detailed test series for process optimization were not possible during this study due to the limited available sample size."

Jan 1, 1989

By J. Peck, M. J. Scobie, M. D. Pollitt

"IntroductionOne aspect of current research in the Canadian Centre for Automation and Robotics in Mining (CCARM) involves the automatic identification of different rock types based on particular drill performance parameter responses. In this paper, the four drill performance parameters of torque, pulldown pressure, rotary speed and penetration rate, were measured from an instrumented rotary blasthole drill during field investigations undertaken at the Fording River Mine, Elkford, British Columbia. The variations in these parameters were subsequently correlated with the corresponding rock types using the results from gamma, neutron and core logs in the same or adjacent boreholes. Work to date has sought to understand the relationships between drilling performance parameter variation and rock properties. Using the results of these studies, the present research is aimed at developing techniques whereby classical statistical pattern recognition methods are applied to drill data to permit the discrimination of different rock units. A monitoring system incorporating such a capability would greatly enhance the quality and amount of geological information on a per borehole basis while drilling. This data in tum could be used economically and directly towards explosive loading, geological exploration and reserve estimation. Background and PhilosophyThis work is an extension of equipment monitoring studies at the Fording River Mine. At this site over a two-year period, 5180 m of data was acquired on an instrumented Bucyrus-Erie 60R drill during routine production blasthole drilling. Throughout these studies, a 311mm diameter S8M Security tungsten-carbide tricone bit was used. The mine, located in southeast British Columbia, is a large-scale, open pit coal operation. The means of excavation revolves around a drill-blast-muck cycle and employs a standard shovel-truck system of transport. Four main rock types are present: sandstone, siltstone, mudstone and coal, with average compressive strengths ranging from 10 MPa to 150MPa respectively (peck 1989). However, based on the field studies, very few differences in terms of strength and compositional properties were seen between the sandstones and siltstones at the site. Therefore, they are referred to as sandstone/siltstone in all further discussions."

Jan 1, 1991