Search Documents

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By L. Hutton, S. W. Colley

"The release of soluble salts of base metals from acid mine pits and in the waste water from metal refiners is an avoidable source local pollution and contamination. Tightening of the regulations controlling natural resource extraction and industrial wastewater discharge is mandating the removal and recovery of metals from waste streams, and the remediation of contaminated sites. There is an economic incentive in recovering the valuable copper and nickel, as the value of the recovered metal can offset remediation costs and for high flow waste streams can be a source of income. Extraction of metals from waste streams by conventional Ion Exchange and chelation resins is widely practised, but has limitations on applicability in complex and dilute feeds due to the structure and properties of polymeric resin beads. Composite Advanced Ion Exchange (AIX) materials have been developed for the recovery and purification of base metals from base metal mining and metal processing industries. A silica-composite based resin has been developed for the selective extraction of copper from high iron containing feeds. This resin can be eluted with sulfuric acid yielding a copper stream suitable for return to solvent extraction or to electrowinning. We describe the development and application of the resin and process to two acid mine drain feeds of varying copper and iron concentrations, and show that the copper concentration can be considerably upgraded even at small scale with a final metal content of >95% copper.INTRODUCTIONWaste water with high sulphate concentrations, low pH and containing complex and variable mixtures of metals is an inevitable product in the mining, extraction and metal refining industries. One problematical water source is Acid Mine Drainage (AMD) which in addition to the metals of interest also contains a wide range of contaminating elements. Purge streams from metal refining are less complex in composition but contain significant quantities of the value metals. The typical treatment of such waste streams is treatment with lime to increase the pH of the water, precipitating the dissolved metals and sulphate as a sludge of mixed metal oxides/hydroxides and sulphates. The process is effective in producing a water stream that can be safely discharged but if there are significant concentrations of value metals such as copper, nickel, zinc then there can be a considerable loss of metal value."

Jan 1, 2016

By T. G. Carter

"This paper traces the introduction and use of fire-resistant (FR) fluids in hydraulic systems at underground mines in British Columbia. Reasons are given for the decision to make compulsory the use of such fluids in underground mines after January 1, 1975 by provincial government legislation. Examples are quoted of fires caused, or supported by, mineral oils which have resulted in loss of life and property.The basic principles of hydraulic systems are reviewed in order to present the effects of changing a system operating on mineral oils to one which must operate on FR fluids. Approximations of the cost of system conversions are given for certain machines and a brief survey is made of the various pieces of underground equipment which contain hydraulic systems operating on FR fluids.IntroductionIn 1948, Admiral Ben Moreel , who was then president of Jones and Laughlin Steel Corporation in the United States , wrote:""Although safe and healthful working conditions can be justified on a cold dollars-and- cents basis, I prefer to justify them on the basic principle that it is the right thing to do. ""(1)This paper will outline the introduction and use of fire resistant fluids at mine operations in the Province of British Columbia. That it was the right thing to do in enhancing the safety and well-being of every person employed at the mines was the prime consideration. That it may be justified on a cold dollars-and-cents basis is left for the reader to judge. The prime purpose of this paper is not so much to trace the efforts made by the individual mines to successfully introduce and use fire-resistant (FR) fluids in hydraulic systems, but to present an over-all picture of what occurred, in a collective sense, at the majority of mines which have ended up with a working FR fluid system. The problems attendant to the introduction of an FR fluid will be recounted in a manner which, it is hoped, will prove useful to those contemplating system conversions. Because the predominant fluid now in use is an invert, or water-in-oil. emulsion, this will be the FR fluid considered.Fluid Loss from SystemsThe quantities of various fluids required for use in hydraulic systems are extremely high. This statement in itself may appear to be redundant in that the capacities of the various systems should demand that a fixed amount of fluid is required for the initial filling of a system, with a further amount of fluid scheduled for use during subsequent fluid changes, i.e. at the recommended change intervals . If only this were the case!"

Jan 1, 1981

By Lar Liljeblad

"As demands upon the earth's natural resources continue to grow, exploration companies, mining organizations and others face the problem of the need to tackle increasingly more difficult strata to open up new reserves. Innovations in materials technology and tool design have steadily improved this capability, but none perhaps so drastically as a recently introduced cemented carbide in which tool wear resistance and/or toughness can be tailored precisely to the user's drilling needs.Introduction Until about forty years ago, the bulk of rock-drilling operations had to be carried out with hardened steels. Short life between re-grinds was common especially in abrasive rock formations. Shortly after World War II, Sandvik, Sweden, pioneered the development of sintered (cemented) carbide-tipped steel tools as a means of improving drill tool life. The new material was a composite of tungsten carbide and cobalt, the latter acting as a 'cement' to bind the wear-resistant carbide grains together, and the composite, in turn, was brazed to the steel. The immediate effect was a 100-fold increase in the service life of the tool.Intractable ProblemsWhile the carbide-tipped tools served the mining and quarrying industries admirably there were, nonetheless, some seemingly intractable limitations. The greater the wear resistance of the material - the quality for which it is selected - the more brittle it is. Also, rocks vary widely in hardness and abrasiveness and no single tool, either in terms of material or shape, meets every need. Specifically, for fast penetration of non-abrasive rock, toughness must be combined with a relatively sharp tool prome. Highly abrasive rock, on the other hand, demands a substantially broad area of extremely wear-resistant material on the tool if long bit life is to be assured. Between these extremes there are innumerable variations in rock"

Jan 1, 1991

By B. M. Das, V. J. Hucka, J. H. Tu

Subsidence can cause serious damage to surface installations such as railroads, highways, pipelines, buildings and other facilities over a period of many years. Although total elimination of the effects of subsidence is difficult, the damage can be minimized through a systematic analysis. An example of such a study for reducing the effects of subsidence on pipelines is presented in this paper. Subsidence-induced stresses on a pipeline over some coal mining properties in Utah have been analyzed using a computer with graphics capabilities. The results are useful in predicting the extent of damages due to mining subsidence. In view of the gradual replacement of room-and-pillar mining by longwall with caving, this sort of analysis will become more and more important. In the next phase of this study the predicted results will be compared with the permissible stress levels on pipelines over actual subsided areas in an actual case.

Jan 1, 1989

By V. Casaletto, L. Widdifield

"Equipment capable of higher production requires more sophisticated maintenance programs. Reduction in fleet size through use of modern technology requires higher utilization and greater availability.Caterpillar's maintenance control system program will display the capabilities of computer technology in a maintenance environment. Utilizing such resources will provide increased availability, lower inventory requirements, fewer last minute disasters, and lower cost per ton for maintenance. High production from premium quality equipment can only be realized by good planning and care, executed by maintenance and operating personnel acting cooperatively.IntroductionAccurate information is the key to accurate decision making. In today' s competitive industry, mines' teeter on the brink between profit and loss. Their survival will be predicated on their ability to retrieve, analyze, and formulate accurate information regarding the operating costs of mobile equipment. This paper deals with the impact of managing equipment operating costs and introduces a computerized control system designed for monitoring and controlling these costs.Caterpillar has produced several computerized modelling programs designed at taking the guesswork out of equipment selection and management. The most basic of these is Equipment Investment Analysis (E.LA.). This model compares two or more alternatives over the projected life of the machine. It deals with comparisons in the owning and operating costs of equipment, as well as, their productivity over a specified period of time.In order for a computer model to be credible as a decision making tool, it must be simple to use and the results measurable and accountable . Caterpillar has introduced several computer models to assist the industry in selecting and managing an equipment fleet. These programs allow the user to predict and monitor the operating costs and production capability of mobile equipment. They are often used in the machine selection process to select equipment which best suits a mine's long-term cost per tonne objectives. After the optimum selection is made, Caterpillar's Maintenance Control System provides an efficient management tool to monitor and verify the data used in the selection model."

Jan 1, 1992

By R. E. G. Caines, P. Alport

"Operating heavy equipment in Labrador, where the winters are 8 months long and the temperature frequently drops below -40°F (-40°C) for days and sometimes weeks presents unique problems in both the operation and maintenance junctions. Winterization programs must be well designed and implemented at the proper time. These programs must include the proper selection of fuel oil, engine oil, hydraulic oils, greases, cooling system fluids, etc. More often than not, modifications have to be made to the original equipment in order that it can be operated safely and economically in the Canadian North. Manufacturers usually design equipment for a less harsh environment and the user makes adaptations by trial and error.Operators have to be trained for the proper operation on ice- and snow-covered roads in an open-pit mine. Special emphasis must be put on haulage road conditions. In this paper, the authors will cover some specific maintenance procedures, equipment modifications and operator training problems experienced by the Iron Ore Company of Canada in its open-pit operation in Labrador.IntroductionT he Iron Ore Company of Canada is engaged in open-pit mining , concentrating and pelletizing of iron ore. The company operates in two provinces, Quebec and Newfoundland (Fig . 1) . The Knob Lake operation "", based in Schefferville, Quebec, has mine sites located both in Labrador and Quebec . The Caro l Lake Project is situated in Labrador, 25 kilometres east o f the Quebec border at Labrador City. The Carol operation mines, concentrates and pelletizes it s o re before rail transportation to the seaport o f Sept-lies via the Quebec North Shore and Labrador Railway."

Jan 1, 1984

By Daniel Hodouin, Robert Lanthier, Yve Dube

"A procedure f or constructing a grinding mill dynamic model is proposed. This model is used in a dynamic simulator of are grinding circuits. The simulator is designed for flexible flow sheets involving different grinding mills and particle classifiers and is able to accept several single variable PID control loops. The dynamic model is validated on a laboratory ball mill, and calibrated to an industrial installation. The simulator is used for characterization of grinding circuit dynamic behaviour and tuning of control strategiesIntroductionThe ore grinding operation is a critical step of the ore preparation process because it is the last comminution stage before the separation of minerals. The properties of the ground minerals to be concentrated, control the quality and efficiency of the separation process. This is why it is important to control properly the operation of the last grinding stage, commonly constituted of a closed circuit ball mill with classifier . To provide an adequate fine product, the grinding operation should compensate for the perturbations of the feed characteristics (size analysis, grindability, etc.). The main objective is to maintain a constant size distribution for providing stable operating conditions to the separation units. Simultaneously another usual objective is to operate the grinding circuit at a maximum capacity.Automatic control applied to grinding circuit s is the appropriate approach to improve its operation. Most frequently average optimal operating conditions are determined from steady -state performances of the circuit , and the automatic control is used for stabilizing the operation at selected values of the process variables . In the traditional approach, one or several single input! single output (SISO) control loops are implemented and empirically tuned. Advanced control practices'!' are based on a quantitative analysis of the circuit dynamics, which could also give a basis for the tuning of conventional SISO 100ps(2)."

Jan 1, 1987

By J. B. Hinzer, J. D. Harvey

"Noranda's Lyon Lake property in the Sturgeon Lake area of Northwestern Ontario was staked by Mattagami Lake Mines Limited in May 1969 to cover airborne Input anomalies. Subsequent ground geophysical and diamond drilling programs resulted in the disco very of the Boundary Extension, Lake and Creek ore zones. As of December 31, 1978, ore reserves were estimated at 3,945,000 tons assaying 6.53 per cent Zn, 1.24 per cent Cu, 0.63 per cent Pb, 3.42 oz/ton Ag and 0.010 oz/ton Au.These deposits are hosted within the South Sturgeon Lake volcanic pile of Archean age, which consists of several cycles of basic intermediate and felsic volcanic materials overlain by a sedimentary iron formation and built upon a plutonic base (Franklin , ' 1975). The top 50 m of the second felsic cycle, according to mine terminolo gy, contains the mineralization within Quartzphenocryst- bearing felsic lapilli tuff and underlying thin discontinuous graphitic sediments and altered coarse pyroclastics. The basal andesitic member of the overlying cycle forms the hanging wall to the ore deposits.Although there is no alteration pipe below the deposits, the coarse footwall rocks are permeated by chlorite, garnet, carbonate, iron sulphide and magnetitie-bearing veins intensifying from west to east.Immediate host rocks are alkali depleted and MnO, FeO, Zn and Cu enriched compared to Goodwin's (1972) average Archean rhyolites. Bedded pyrite-pyrrhotite-chalcopyrite lenses with sphalerite-rich tops are underlain by weakly developed stringer mineralization.Traversing eastward from the Lake Zone to the Creek Zone and toward the Sturgeon Lake Mine deposit, more rapid facies changes, more pronounced chloritic and carbonate alteration, the presence ofgarnets, greater MnO, FeO, CaO and Ag abundances, and increasing Zn/Cu and MnO/FeO ratios are apparent."

Jan 1, 1981

By D. Assmus, S. Daly

"Poor fragmentation, high toe areas, excessive shovel wear and tear and frequent re-drilling and blasting of certain tough waste rock zones in the Lomex pit in the early 1980snecessitateda better understanding of these zones.A combination of geotechnical mapping, penetration rate data, toe elevation contouring and observations on shovel and drill performance were used to determine the character and extent of these zones. This complementary information was brought together by the geotechnical mapper and the explosives supervisor.Distinct zones with particular geological characteristics were determined. A classification system with three types of blast and dig-ability was developed for the Lomex pit and later applied to the Valley pit, with considerable success. The three blast zone types are called ""poor"", ""f air"", and ""good"". This system will be described in detail.The explosives supervisor adjusted the blasting parameters to each zone, in particular, pattern spacing and burden. The resulting powder factors showed considerable variation between the poor, fair and good zones within each pit as well as between the two pits. Pattern geometry and length of collar were also adjusted to improve fragmentation. Cost savings resulted from less re-drilling and less wear and tear on drills and shovels in the poor zones and more efficient use of explosives in all the zones. An annual estimated cost savings of well in excess of $1,000,000 is realized at Highland Valley Copper. A by-product of the mapping was the determination of unstable structures and water flowing zones. Blasting was then adapted to this information for enhanced slope stability."

Jan 1, 1992

By Robert B. Parsons

"The Department of Finance introduced draft amendments to the resource allowance regulations on July 23, 1992 that effectively nullify the decision in the Gulf Canada Limited case. Prior to the amendments it appeared that only ""directly"" related general and administrative, capital cost allowance and scientific research expenditures had to be deducted from resource profits. Now ancillary expenditures are required to be deducted. Consequently, the ability of taxpayers to claim the resource allowance is curtailed.IntroductionOn October 25, 1990 it was almost certain that taxable mines were going to get a break. The Federal Court-Trial Division had just decided in Gulf Canada Limited's favour to allow it to claim resource related tax benefits larger than what Revenue Canada evidently wished. Revenue Canada appealed first to the Federal Court of Appeal and then to the Supreme Court of Canada. On January 10, 1992 the Federal Court of Appeal agreed with the Federal Court decision and on July 2, 1992the Supreme Court declined to hear any further appeal. A mere three weeks later, on July 23, 1992, the Department of Finance issued draft ""clarifying"" measures to amend the calculation of the resource allowance. These measures effectively nullify the benefits that arose under the decisions of the Federal Court."

Jan 1, 1992

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By Roger Lafrance

"This paper discusses various aspects affected by the use of large-diameter boreholes in underground mines. Topics covered consist of noxious fumes, vibrations, post-blast effects, various types of explosives, the cordine system in production blasts, the slider primer system and wall-control methods. In general, the paper is an overview of this important fact of underground mining.IntroductionWith economical factors leading the way, many reasons motivated drilling equipment companies to develop equipment that can drill holes up to eight inches in diameter and even larger for underground applications. One of these other reasons is the fact that many orebodies were considered marginal, given the high costs of conventional mining methods utilizing small diameter boreholes. With these criteria in mind, accelerated programs were put in motion to develop equipment that would reduce both-development and production costs in underground mines. Change s in any basic program often affect other areas down the line. This is particularly true with the ad vent of large-diameter boreholes underground.C-I-L Inc. is certainly no stranger to this phenomena. Whether production headings increase in size and tonnage or whether production increases due to lower costs, one fact remains unchanged and that is the fact that all development and production holes are loaded and blasted whether they be of small or large diameter. Due to this fact, C-I-L Inc., as a leading explosives manufacturer, initiated a program to examine blasting methods in use in surface work with the intent of revising these method s for underground applications. Research facilities were also oriented toward developing appropriate products. This was a task that was accepted with anticipation, with the result that many new blasting systems and methods were brought forward, thanks to the collective efforts of both the consumers and manufacturers."

Jan 1, 1984

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By James K. Gowans

"Cominco Ltd's Polaris Mine, located on Little Cornwallis Island, Northwest Territories (latitude 75degrees 30') went into production in late 1981, becoming the world's most northerly base metal mine. The concentrator, powerhouse, shops, offices, dry and warehouse, were uniquely designed and constructed on a 100f t wide by 400 ft long by 65 ft high barge. This process barge was constructed in southern Canada at Trois Rivières, then towed 3,500 miles into the High Arctic Islands and beached on Little Cornwallis Island.The paper deals with the original design philosophy, flowsheet and the initial year's operation of the Polaris process barge.IntroductionTo bring a mining property into production in the Canadian High Arctic, a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these fact or s, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gamed at the Black Angel Min e on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during the ""shipping window"". The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months' production was gained by opting for the ""barge"" approach."

Jan 1, 1983

By G. R. Larocque

"The Loss Prevention Program and management style applied at Kidd Creek enabled them to maintain a 1.02/200 000 man-hours accident frequency over a 20-year period. Falconbridge Limited, Kidd Creek Division operates a major zinc, copper, silver mine, two gold mines and a metallurgical facility in Timmins, Ontario. The metallurgical site and the base metal mine are 17 miles apart and joined by their own railroad. The minesite consists of two shafts, one 3000 feet deep and the other to 5200 feet deep, as well as the necessary maintenance and service shops. The metallurgical site consists of a 14 000 STPD concentrator, a zinc refining plant, copper smelter, copper refinery, and the necessary maintenance shops. The two gold mining operations are adjacent to the metallurgical site.At the time of writing this paper the workforce consisted of some 2500 people divided between the two sites. Nine hundred and ninety-two employees are stationed at the minesite, with the remainder at the metallurgical site and gold mines. The workforce in the Timmins operation is non-unionized and reflects the belief that employee interests are well served.Beside providing competitive wages and an excellent benefit package, Kidd Creek takes special pride in its employee relations practices and continued efforts in communication.In each of the programs referred to, there have been equal involvement by both management and the employees. Each crew, under the direction of a supervisor, makes up its own health and safety committee. To maintain a successful Loss Prevention Program, it is essential that management and the employees work closely together and provide meaningful input and effort to succeed.At this point, refer to the lost time injury frequency as a measure of failure and refer to the opposite end of the scale as the measure of success. The ultimate goal of every operating company is to have a zero frequency, therefore denoting 100070 success. The company uses most of the tangible safety aids found in other mining operations, such as safety posters, safety reminders, check lists, and the use of the Neil George Safety System. The difference is the manner and style of management at the Kidd Creek Division. Their ""open door"" policy and the close association, between management and the employees, has always served them well. Also, at Kidd Creek they believe they have a well-trained and dedicated workforce."

Jan 1, 1989

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was' put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

By P. R. A. Andrews, R. K. Collings

"There are more than 300 occurrences of fluorite in Canada. Deposits of economic significance, however, are confined to Newfoundland and Nova Scotia in eastern Canada, Ontario in central Canada, and British Columbia in western Canada. Fluorite has been mined and processed intermittently in Ontario and Newfoundland until November 1990, when Canada's only producer Minworth Ltd., a U.K. based company, with a mine and concentrator near St. Lawrence on the Burin Peninsula, Newfoundland, closed its operation.CANMET has processed ore samples from each of the major mineralized areas, and thirty-one studies were conducted between 1920and 1970. A summary of the important aspects of the various testwork studies is presented. The production of acid-grade fluorite was possible by flotation, and ceramic-grade, by flotation and gravity concentration methods. Gravity concentration methods included heavy media separation, jigging and tabling. Flotation was by direct and reverse techniques; associated minerals, quartz, calcite, barite, etc. were depressed by a variety of depressants. The function of the major depressants is discussed briefly. The various uses offluorite which include hydrofluoric acid, chlorofluorocarbons, aluminum production, petroleum alkylation, fluxing and ceramic applications etc. are discussed briefly."

Jan 1, 1993

"Nanisivik Mines Ltd. operates a 10-M W diesel-electric generating plant at its zinc-lead operation on Baffin Island in the Canadian Arctic. This paper provides a description of the plant and the integrated waste heat recovery system. Data is presented detailing the actual costs of operating a plant over a period of seven years. Problems in operation are described as well as the success of the plant in meeting its objectives over the years. IntroductionNanisivik is located on the shore of Strathcona Sound at the north end of Baffin Island (Fig. I). Nanisivik Mines Ltd. has operated a 2,100 tonne per day zinc-lead underground mine and a concentrator, together with supporting infrastructure, at this location since October 1976. Annual production of 100 000 tonnes of zinc and 10 000 tonnes of lead concentrate is transported by ship to Europe during the mid -July to mid October shipping season.All electrical needs of the project are provided by the company-owned and -operated power plant. Facilities served by this electrical system are the underground mining areas, the concentrator and industrial area, a townsite, airport, and shiploading dock complex."

Jan 1, 1986

By Hung-wei Liu, Kevin Plucknett

Early attempts to manufacture titanium aluminides using blended elemental powders, through powder metallurgical processes, have been obstructed due to serious swelling during sintering. Although the use of pre-alloyed powder can avoid this undesired expansion problem, there are limited commercial powder sources available. Therefore, in the present research, fundamental studies on the synthesis of dual-phase (? plus a2) Ti48Al intermetallic materials is undertaken, in particular assessing powder manufacture. In order to produce pre-alloyed powders, highly porous Ti48Al pieces are initially sintered from elemental Ti and Al powder blends, and subsequently pulverised into powders. The powder size is then further reduced by use of either dry or wet milling processes (i.e. shatterbox grinding, attrition, or ball milling). Among these methods, shatterbox grinding has shown the highest efficiency, with a slight mechanical alloying effect observed. The manufactured powder morphologies and phases, as well the sintered material, will be discussed.

Jan 1, 2015